Installation Manual

ManualsBrandsComnet ManualsElectronicsRS232/422/485 2&4W Bi-directional Data Transceiver

INS_FDX60_REV–

04/23/10

PAGE 1

INSTALLATION AND OPERATION MANUAL

FDX60(M)(S)(-M)

SINGLE OR DUAL

RS232/RS422/RS485(2/4W)

DATA TRANSCEIVER

The ComNet™ FDX60(M)(S)(-M) data transceivers provide point-to-point

transmission of simplex or duplex EIA RS232/RS422/RS485 (2W/4W) data

signals over one or two optical fibers. The transceivers are transparent to data

encoding allowing for broad-range compatibility. Models within this series are

available for use with multimode or single mode optical fiber.

Each transceiver incorporates a bi-color (Red/Green) indicating LED for

monitoring proper system operation. See Figure 8 on Page 6 for LED Indicator

explanations.

The FDX60(M)(S)(-M) has a built-in fiber link test feature that allows for the

testing of the fiber. See Figure 13 on Page 8 for an explanation of the Loop

Back Test Mode.

The FDX60(M)(S) may be directly plugged into the ComNet Rack (Part C1) or

they can operate as standalone modules. The FDX60(M)(S)-M has a small

footprint and is designed for surface mounting. See Figures A and B on

Page 9 for mounting instructions.

See Figures 1 – 13 for complete installation details.

Summary of content (9 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) SINGLE OR DUAL RS232/RS422/RS485(2/4W) DATA TRANSCEIVER The ComNet™ FDX60(M)(S)(-M) data transceivers provide point-to-point transmission of simplex or duplex EIA RS232/RS422/RS485 (2W/4W) data signals over one or two optical fibers. The transceivers are transparent to data encoding allowing for broad-range compatibility. Models within this series are available for use with multimode or single mode optical fiber.
PAGE 2
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 1 – FDX60 1 FIBER TRANSCEIVER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE/RED FIGURE 2 – FDX60 1 FIBER TRANSCEIVER FRONT PANEL REAR PANEL NOTE: Remove Electrical Connector for Rack Mount Units TECH SUPPORT: 1.888.678.
PAGE 3
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 3 – FDX60 2 FIBER TRANSCEIVER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE/RED FIGURE 4 – FDX60 2 FIBER TRANSCEIVER FRONT PANEL REAR PANEL NOTE: Remove Electrical Connector for Rack Mount Units TECH SUPPORT: 1.888.678.
PAGE 4
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 5 – FDX60-M 1 FIBER TRANSCEIVER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE/RED FIGURE 6 – FDX60-M 1 FIBER TRANSCEIVER FRONT PANEL REAR PANEL NOTE: Remove Electrical Connector for Rack Mount Units TECH SUPPORT: 1.888.678.
PAGE 5
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 7 – FDX60-M 2 FIBER TRANSCEIVER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE/RED FIGURE 8 – FDX60-M 2 FIBER TRANSCEIVER FRONT PANEL REAR PANEL NOTE: Remove Electrical Connector for Rack Mount Units TECH SUPPORT: 1.888.678.
PAGE 6
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 9 – LED INDICATORS LINK DATA (TX/RX) LOOP BACK (Test Mode) POWER GREEN Unit In Sync Activity Fiber Link Connections are Correct Unit Powered Up RED Unit Not In Sync No Acvitiy Fiber Link Issue Exists (Head End) – OFF No Optical Link – Fiber Link Issue Exists (Far End); Unit Powered Down OR Test Mode is Off FIGURE 10 – SWITCH POSITIONS RS232 Data 1 2 3* RS422, Bi-Phase or Manchester Data 1 2 3* Switch Located on front panel in f
PAGE 7
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 11 – DATA CONNECTIONS – Data In/Out + Data In/Out – Data Out + Data Out RS232 Out RS232 In GND FIGURE 12 – DATA SETTINGS RS232 RS422 Bi-phase or Manchester Customer Equipment FDX60 Signal – Pin FDX60 Signal – Pin Data Transmit IN – 2 OUT – 3 Data Receive Data Receive OUT – 3 IN – 2 Data Transmit Signal Ground GND – 1 GND – 1 Signal Ground FDX60 Signal – Pin FDX60 Signal – Pin Data Out (+) +IN/OUT – 6 +OUT – 4 Data In (+) Da
PAGE 8
INSTALLATION AND OPERATION MANUAL FDX60(M)(S)(-M) FIGURE 13 – LOOP BACK TEST MODE 1. On one end (Head End), put unit into Loop Back Mode by setting Switch 3 to “OFF.” Switch 1 and 2 can be in any position. Data will not pass during Loop Back Test, LEDs may flash if data is sent during Loop Back Test. 2. If the Far End unit is powered on and the fiber link connections are correct, the Far End unit Loop Back LED will light GREEN. 3.
PAGE 9
MECHANICAL INSTALLATION INSTRUCTIONS INSTALLATION CONSIDERATIONS This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity. FIGURE A Dimensions are for a standard ComNet™ one slot module .156 [3.