Installation Manual

ManualsBrandsComnet ManualsElectronicsSimplex Audio Transmitter with Contact Closure

INS_F(T,R)A2C1(M,S)1_FXA2C1(M,S)1_REV– 04/25/12 PAGE 1

INSTALLATION AND OPERATION MANUAL

FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1

2 AUDIO CHANNELS + 1 CONTACT CLOSURE

The ComNet

™

FTA/FRA2C1 Series audio multiplexer provides the transmission of two

audio signals and one contact closure over one multimode or single mode optical

fiber. A bidirectional model, FXA2C1(M,S)1, is also available. The modules use 24-bit

96kHz sample rate digital encoding for superior transmission of balanced line-level

audio. Plug-and-play design ensures ease of installation and no electrical or optical

adjustments are required.

These extenders are designed for long-term, reliable operation in harsh industrial

environments, and a fault-specific LED indicator is provided for rapidly ascertaining

the operating status of the extender and the link. See Figure 9 on Page 5 for an

explanation of LED indicators.

Packaged in the exclusive ComNet ComFit housing, these units may be either wall or

rack mounted. See Figure A on Page 6 for mounting instructions.

See Figures 1 – 9 for complete installation details.

This manual serves the following

ComNet Model Numbers:

FTA2C1M1

FRA2C1M1

FTA2C1S1

FRA2C1S1

FXA2C1M1A

FXA2C1M1B

FXA2C1S1A

FXA2C1S1B

Summary of content (6 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1 2 Audio Channels + 1 Contact Closure This manual serves the following ComNet Model Numbers: FTA2C1M1 FRA2C1M1 FTA2C1S1 FRA2C1S1 FXA2C1M1A FXA2C1M1B FXA2C1S1A FXA2C1S1B The ComNet™ FTA/FRA2C1 Series audio multiplexer provides the transmission of two audio signals and one contact closure over one multimode or single mode optical fiber. A bidirectional model, FXA2C1(M,S)1, is also available.
PAGE 2
INSTALLATION AND OPERATION MANUAL FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1 FIGURE 1 – FTA2C1 TRANSMITTER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE/RED Power Supply: 8-15VDC @ 2W Note: Remove Electrical Connector for Rack Mount Units FIGURE 2 – FTA2C1 TRANSMITTER FRONT PANEL Tech Support: 1.888.678.
PAGE 3
INSTALLATION AND OPERATION MANUAL FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1 FIGURE 3 – FRA2C1 Receiver MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE/RED Power Supply: 8-15VDC @ 2W Note: Remove Electrical Connector for Rack Mount Units FIGURE 4 – FRA2C1 Receiver FRONT PANEL Tech Support: 1.888.678.
PAGE 4
INSTALLATION AND OPERATION MANUAL FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1 FIGURE 5 – FXA2C1 TRANSceiver MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK n BLACK WITH WHITE STRIPE/RED Power Supply: 8-15VDC @ 2W Note: Remove Electrical Connector for Rack Mount Units FIGURE 6 – FXA2C1 TRANSceiver FRONT PANEL REAR PANEL n Tech Support: 1.888.678.
PAGE 5
INSTALLATION AND OPERATION MANUAL FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1 FIGURE 7 – AUDIO WIRING Wiring panel terminal block is located on the back panel of each unit.
PAGE 6
MECHANICAL INSTALLATION INSTRUCTIONS Installation Considerations This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity. FTA/FRA2C1(M,S)1 and FXA2C1(M,S)1 Figure A Dimensions are for a standard ComNet™ one slot module. .156 [3.