Data Sheet

SPECIFICATIONS
Video
Video Input 1 volt pk-pk (75 ohms)
Overload >1.5 V pk-pk
# Input/Output Channels 32
Bandwidth (minimum) 10 Hz - 6.5 MHz per channel
Differential Gain <2%
Dif feren tial P hase <0.7˚
Tilt <1%
Signal-to-Noise Ratio (SNR) 67 dB Typical
Max. RG-59 COAX Distance 100m (300 ft) Camera to Fiber Optic Module to
maintain 6 Mhz Bandwidth
Data
Data Channels 8
Data Interface RS232, RS422 and RS485 (2 W/4 W)
Data Format NRZ, NRZI, Manchester, Bi-Phase and Sensornet
Data Rate DC-250 Kbps (NRZ)
Bit Error Rate <1 in 1010 @ Maximum Optical Loss Budget
Operating Mode Simplex or Full-Duplex
Wavelength Single Mode 9/125µm
Number of Fibers 1
LED Indicators › Video Sync Presence for Each Video Channel
› Received Data › Transmitted Data
› Optical Carrier Detect › Power
Optical Emitter Laser Diode
Connectors
Optical ST
Power Terminal Block
Video BNC (Gold Plated Center-Pin)
Data RJ45 (5 pcs. Included)
Power
Operating Voltage Range 90 to 264 VAC
Power Consumption 70 W Max
Output Voltage 9 VDC +/- 5% @ 6.5 Amps @ 75˚C
Fusing 1.25 A slow blow (rack power supply)
(plug-in modules individually electronically fused)
Mechanical
Current Protection Automatic Resettable Solid-State Current Limiters
Circuit Board Meets IPC Standard
Size (L×W×H) 19 × 7.5 × 6 in (48 × 19 × 15 cm)
Shipping Weight <8 lb /3.6 kg
Environmental
MTBF >100,000 hours
Operating Temp -40˚ C to +75˚ C
Storage Temp -40˚ C to +85˚ C
Relative Humidity 0% to 95% (non-condensing)
1
FVT/FVR320D8S1
32-Channel Digitally Encoded Video
+ 8 Bi-Directional Data Channels/10-Bit Digital/Short-Haul Video
V
D
V
D
FVT320D8S1
FVT320D8S1
32
8
32
8
TYPICAL APPLICATION
OPTICAL FIBER
COPPER CABLE
ORDERING INFORMATION
Part Number Description Fibers Req’d Fiber
Optical Pwr
Budget Max Distance²
FVT320D8S1 Video Transmitter/Data Transceiver 1 Single Mode 9/125µm 18 dB 36 km (22 miles)
FVR320D8S1 Video Receiver/Data Transceiver 1 Single Mode 9/125µm 18 dB 36 km (22 miles)
Accessories Power Cord
Options [1] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)
[2] Distance may be limited by optical dispersion. This product requires a fiber installation with a minimum 30 dB connector return loss. The use of
Super Polish Connectors is recommended.
Complies with FDA Performance Standard for Laser Products, Title 21, Code of Federal Regulations, Subchapter J
In a continuing effort to improve and advance technology, product specifications are subject to change without notice.
19 Jun 2015© 2015 Communication Networks. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks.
3 CORPORATE DRIVE
|
DANBURY, CONNECTICUT 06810
|
USA
|
T: 203.796.5300
|
F: 203.796.5303
|
TECH SUPPORT: 1.888.678.9427
|
[e-mail]
8 TURNBERRY PARK ROAD
|
GILDERSOME
|
MORLEY
|
LEEDS, UK LS27 7LE
|
T: [phone]
|
F: [phone]
|
[e-mail]