Installation Manual

ManualsBrandsComnet ManualsElectronics4-Ch Digital Video Receiver + 2Ch Bi-directional Data

INS_FVT/FVR4012_REV–

02/29/12

PAGE 1

INSTALLATION AND OPERATION MANUAL

FVT/FVR4012

4-CHANNEL 10-BIT DIGITALLY ENCODED VIDEO

+ 2 BI-DIRECTIONAL DATA CHANNELS

+ 1 BI-DIRECTIONAL CONTACT CLOSURE

The FVT/FVR4012(M,S)1 Series transmits four (4) channels of video utilizing

state of the art 10-bit digital encoding and decoding for very high quality video

transmission, along with two (2) channels of bi-directional data and one (1)

bi-directional contact closure over one single mode or multimode optical fiber.

This equipment is environmentally hardened and suitable for use in unconditioned

roadside or out-of plant installations.

The FVT/FVR4012 is compatible with NTSC, PAL and SECAM video transmission

protocols and supports bi-directional RS232, 422 and 485 (2 & 4 Wire) data. See

Figure 4 on Page 3 for data selection.

See Figure 6 on Page 5 for contact switch positions.

Bi-Color LED indicators are provided to indicate the status of the system, video and

data. See Figure 7 on Page 5 for LED indication explanations.

These units may be directly plugged into the ComNet Rack (Part C1) or they can

operate as standalone modules. See Figure A on Page 6 for mounting instructions.

See Figures 1 – 7 for complete installation details. No additional parts or power

supplies are required.

Summary of content (6 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL FVT/FVR4012 4-channel 10-Bit digitally encoded video + 2 bi-directional data channels + 1 bi-directional contact closure The FVT/FVR4012(M,S)1 Series transmits four (4) channels of video utilizing state of the art 10-bit digital encoding and decoding for very high quality video transmission, along with two (2) channels of bi-directional data and one (1) bi-directional contact closure over one single mode or multimode optical fiber.
PAGE 2
INSTALLATION AND OPERATION MANUAL FVT/FVR4012 FIGURE 1 – FVT/FVR4012 TRANSMITTER AND RECEIVER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPE Power Supply: Surface Mount: 9-12 VDC @ 1A. Rack Mount: From Rack NOTE: Remove Electrical Connector for Rack Mount Units FIGURE 2 – FVT4012 TRANSMITTER FIGURE 3 – FVR4012 RECEIVER FRONT PANEL FRONT PANEL Tech Support: 1.888.678.
PAGE 3
INSTALLATION AND OPERATION MANUAL FVT/FVR4012 FIGURE 4 – DATA SWITCH POSITIONS The mode for each data channel is configured using a pair switches on the front panel of the unit.
PAGE 4
INSTALLATION AND OPERATION MANUAL FVT/FVR4012 FIGURE 5 – DATA CONNECTIONS See Page 3 for Switch Settings RS-232 RS-422 Bi-phase or Manchester 2-Wire RS-485, Sensornet 4-Wire RS-485 Customer Equipment FVT4012 FVR4012 Customer Equipment Data Transmit DIN(-) DOUT(-) Data Receive Data Receive DOUT(-) DIN(-) Data Transmit Signal Ground GND GND Signal Ground Data Out (+) DIN(+) DOUT(+) Data In (+) Data Out (-) DIN(-) DOUT(-) Data In (-) Data In (+) DOUT(+) DIN(+) Data Out (+) D
PAGE 5
INSTALLATION AND OPERATION MANUAL FVT/FVR4012 FIGURE 6 – CONTACT SWITCH POSITIONS The four CONTACT switches on the front of the unit set the operating mode of the CONTACT OUT terminal pair. It can either function as an alarm to indicate fault conditions, or it can function as a contact closure to indicate the state of the CONTACT IN terminal pair on the rear of the unit at the other end of the fiber. 1 2 3 4 ON OFF OFF OFF Closed when optical Port has established link.
PAGE 6
MECHANICAL INSTALLATION INSTRUCTIONS Installation Considerations This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity. Figure A Dimensions are for a standard ComNet™ two slot module C1-US, C1-EU, C1-AU or C1-CH Card Cage Racks .156 [3.