Installation Manual

ManualsBrandsComnet ManualsElectronicsMini Digital Video Transmitter/ Data Transceiver

INS_FVT/FVR110_REV–

10/27/11

PAGE 1

INSTALLATION AND OPERATION MANUAL

FVT/FVR110(M,S)1[/M]

10-BIT DIGITAL VIDEO WITH

ONE BI-DIRECTIONAL DATA CHANNEL

The ComNet

™

FVT/FVR110 series is a video transmitter/receiver and data transceiver

that supports the simultaneous transmission of short haul quality 10-bit EIA RS-250C

digitally encoded video and bi-directional data over one multimode or single mode

optical fiber. The FVT110 also transmits a single bi-directional contact closure signal.

The module is universally compatible with major CCTV camera manufacturers.

Figures 6 and 7 starting on Page 4 illustrate the specific data connections for

RS232, RS422, 2 or 4-wire RS485 data transmission.

The FVT/FVR110 also supports “up-the-coax” data transmission from all major

manufacturers, utilizing time-base correction these units can achieve distances of

48km. The FVT/FVR110 supports Panasonic Proteus

™

, Pelco Coaxitron

™

and Bosch

Bilinx

™

Up-the-Coax systems.

Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment

operating status. Figure 10 on Page 6 describes the LED indicators for each light on

the unit.

The FVT110 and FVR110 units are interchangeable between stand-alone or card

mount configurations, or may be DIN-rail mounted by the addition of ComNet

model DINBKT1 adaptor plate. The FVT110M is stand-alone only. See Figure A on

Page 8 for mounting instructions.

Summary of content (8 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] 10-BIT DIGITAL VIDEO WITH ONE BI-DIRECTIONAL DATA CHANNEL The ComNet™ FVT/FVR110 series is a video transmitter/receiver and data transceiver that supports the simultaneous transmission of short haul quality 10-bit EIA RS-250C digitally encoded video and bi-directional data over one multimode or single mode optical fiber. The FVT110 also transmits a single bi-directional contact closure signal.
PAGE 2
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] FIGURE 1 – FVT/FVR110 TRANSMITTER AND RECEIVER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPES Operating Voltage Range: 8–15 VDC Power Consumption: 6W Max NOTE: Remove Electrical Connector for Rack Mount Units FIGURE 2 – FVT110 TRANSMITTER FIGURE 3 – FVR110 RECEIVER FRONT PANEL FRONT PANEL TECH SUPPORT: 1.888.678.
PAGE 3
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] FIGURE 4 – FVT110/M TRANSMITTER MULTIMODE OR SINGLE MODE OPTICAL FIBER BLACK BLACK WITH WHITE STRIPES Operating Voltage Range: 8–15 VDC Power Consumption: 6W Max FIGURE 5 – FVT110M TRANSMITTER FRONT PANEL REAR PANEL VIDEO IN OPTICAL DATA FORMAT LEDs: LINK VIDEO DATA GND +Vin INS_FVT/FVR110_REV– 10/27/11 PAGE 3
PAGE 4
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] FIGURE 6 – DATA SWITCH POSITIONS The mode for each data channel is configured using a pair of switches on the front panel of the unit. Switch 1 ON Switch 2 ON ON OFF OFF ON OFF OFF Switch FVT110/M FVT110 FVR110 TECH SUPPORT: 1.888.678.
PAGE 5
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] FIGURE 7 – DATA CONNECTIONS Customer Equipment UTC Control RS232 RS422 Bi-phase or Manchester 2-Wire RS485 4-Wire RS485 Customer Equipment FVT110 FVR110 VIDEO IN VIDEO OUT Customer Equipment FVT110 FVR110 Customer Equipment Data Transmit DIN(–) DOUT(–) Data Receive Up-the-Coax Control Receiver Up-the-Coax Control Transmitter Data Receive DOUT(–) DIN(–) Data Transmit Signal Ground GND GND Signal Ground Data Out (+) DIN(+)
PAGE 6
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] FIGURE 8 – CONTACT CLOSURE The FVT110 transmits the state of a contact closure input over fiber to an output relay on the FVR110. FVT110 FVT110/M Dry contact closure input. Applying a voltage to these pins may damage the unit. Dry contact closure input. Applying a voltage to these pins may damage the unit.
PAGE 7
INSTALLATION AND OPERATION MANUAL FVT/FVR110(M,S)1[/M] FIGURE 10 – LED INDICATORS LINK GREEN Communication link has been established over optical fiber RED Communication link has not been established. OFF Unit powered down. TECH SUPPORT: 1.888.678.9427 VIDEO An active video signal is present on the BNC connector. No active video signal present on the BNC connector. Unit powered down. DATA IN POWER CIN An active data Unit powered up Contact Closed signal is present on the pins of the data connector.
PAGE 8
MECHANICAL INSTALLATION INSTRUCTIONS INSTALLATION CONSIDERATIONS This fiber-optic link is supplied as a Standalone/Rack module. Units should be installed in dry locations protected from extremes of temperature and humidity. FIGURE A Dimensions are for a standard ComNet™ one slot module .156 [3.