Data Sheet

SPECIFICATIONS
Data
Video Input 1 volt pk-pk (75 ohms)
Overload >1.5 V pk-pk
# Input/Output Channels 8
Bandwidth (minimum) 10 Hz - 6.5 MHz per channel
Differential Gain <4%
Dif feren tial Phase <0.7˚
Tilt <1%
Signal-to-Noise Ratio (SNR) 57 dB Typical
Max. RG-59 COAX Distance 100m (300 ft) Camera to Fiber Optic Module to
maintain 6 Mhz Bandwidth
Wavelength 1310 nm, Multimode and Single Mode
Number of Fibers 1
Optical Emitter Laser Diode
Connectors
Optical ST
Power Terminal Block
Video BNC (Gold Plated Center-Pin)
LED Indicators › Video Sync Presence for Each Video Channel
› Optical Carrier Detect › Power
Power
Surface Mount 8 to 15 VDC
Power Consumption 4 W
Rack Mount From Rack
Electrical & Mechanical
Number of Rack Slots 2
Current Protection Automatic Resettable Solid-State Current Limiters
Circuit Board Meets IPC Standard
Size 6.1 × 5.3 × 2.2 in (15.5 × 13.5 × 5.6 cm)
Shipping Weight <2 lb./0.9 kg
Environmental
MTBF >100,000 hours
Operating Temp -40˚ C to +75˚ C
Storage Temp -40˚ C to +85˚ C
Relative Humidity 0% to 95% (non-condensing)¹
ValueLine
FVT/FVR81(M,S)1
8-Channel Digitally Encoded Video
TYPICAL APPLICATION
ORDERING INFORMATION
OPTICAL FIBER
VIDEO (Coax)
Part Number Description
Fibers
Required Fiber
Optical PWR
Budget
Max.
Distance²
# Rack
Slots
FVT81M1 Video Transmitter (1310 nm)
1 Multimode 62.5/125µm 16 dB 2 km (1.2 miles) 2
FVR81M1 Video Receiver (1310 nm)
FVT81S1 Video Transmitter (1310 nm)
1 Single Mode 9/125µm 16 dB³ 48 km (30 miles) 2
FVR81S1 Video Receiver (1310 nm)
Accessories
Options
DC Plug-in Power Supply, 90-264 VAC, 50/60 Hz (Included)
[1] Add suffix ‘/C’ for Conformally Coated Circuit Boards to extend to condensation conditions (Extra charge, consult factory)
DIN-Rail Mounting Adaptor Plate Kit – With mounting hardware (Optional, order model DINBKT1 or DINBKT4)
NOTE: This product requires a fiber installation with a minimum 30 dB connector return loss. The use of Super Polish Connectors is recommended.
Complies with FDA Performance Standard for Laser Products, Title 21, Code of Federal Regulations, Subchapter J. In a continuing effort to improve
and advance technology, product specifications are subject to change without notice.
[2] Distance may be limited by optical dispersion. High bandwidth 50/125µm fiber is required to achieve maximum multimode distance. Contact
ComNet tech support before using these units for distances greater than 2 km. [3] Add “HP” to model number for 23dB.
1 Fiber
V V
FVT81S1
FVR81S1
8 8
16 Mar 2015© 2015 Communication Networks. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks.
3 CORPORATE DRIVE
|
DANBURY, CONNECTICUT 06810
|
USA
|
T: 203.796.5300
|
F: 203.796.5303
|
TECH SUPPORT: 1.888.678.9427
|
[e-mail]
8 TURNBERRY PARK ROAD
|
GILDERSOME
|
MORLEY
|
LEEDS, UK LS27 7LE
|
T: [phone]
|
F: [phone]
|
[e-mail]