NW10 Series-Quick Start guide

ManualsBrandsComnet ManualsWireless TransmissionWireless Radio High Performance for High Density Environments

INS_NW10_NW10E_QS_REV– 07/7/15 PAGE 1

QUICK START GUIDE

INDUSTRIAL OUTDOOR HIGH THROUGHPUT

802.11A/N WIRELESS ETHERNET

Thank you for purchasing NetWave

from ComNet. This quick start guide is designed to

walk you through installation.

This guide applies to the following models:

NW10: Industrial Multipoint, FCC Version, User Configurable

NW10E: Industrial Multipoint, ETSI Version, User Configurable

An easy to read LED array displays unit operational status along with received signal

strength ensuring optimal installation and operation. See Figure 2 on Page 2 for LED

Indicator explanations.

See Figures 3 through 5 beginning on Page 3 for mounting instructions.

This manual serves the following

ComNet Model Numbers:

NW10

NW10E

Summary of content (9 pages)

PAGE 1
QUICK START GUIDE INDUSTRIAL OUTDOOR HIGH THROUGHPUT 802.11A/N WIRELESS ETHERNET This manual serves the following ComNet Model Numbers: NW10 NW10E Thank you for purchasing NetWave® from ComNet. This quick start guide is designed to walk you through installation.
PAGE 2
QUICK START USER GUIDE NW10[E] FIGURE 1 – INDUSTRIAL HIGHTHROUGHPUT WIRELESS ETHERNET LINK PORT 1 - POE IN FRONT PORT 2 - POE OUT PORT 2 - POE OUT BACK PORT 1 - POE IN IMPORTANT: Only plug PoE power to Port 1. Connecting a PoE power source to the PSE Port (#2) will cause a major device malfunction and void the warranty.
PAGE 3
QUICK START USER GUIDE NW10[E] FIGURE 3 – INSTALLATION INSTRUCTIONS Step 1. Unpack the mounting hardware from the box. Determine if this will be a pole or wall mount application. The included Mounting kit is designed to support poles up to 2 in (5.8 cm) in diameter. If surface or wall mounting, the optional NWBKT hardware will be required. Step 2. A. Route the RJ45 connectorized Ethernet cable through the weather tight gland connection as shown at left.
PAGE 4
QUICK START USER GUIDE NW10[E] FIGURE 4 – POLE MOUNT INSTRUCTIONS Included Hardware Vertical Mount in -45º Position TECH SUPPORT: 1.888.678.
PAGE 5
QUICK START USER GUIDE NW10[E] INSTALLATION REQUIREMENTS Shielded outdoor CAT 5 or better should be used for all out of plant Ethernet connection and should be properly grounded through the PoE AC ground. Industrial grade shielded Ethernet cable is recommended to help prevent ESD damage commonly experienced with outdoor installations. Visit www.comnet.net/comnet-products/cables CONFIGURING NETWAVE 1.
PAGE 6
CONFIGURING MAC LOCK FOR POINT TO POINT LINKS MAC-Filter replaces MAC-Lock on the first generation Netwave hardware. MAC-Filter is only available on devices operating as an AP. By default, it is disabled. You can locate MAC-Filter tab by going to Networking -> WIFI -> Enable. To enable and lock to a client radio, Click on the drop down menu and select “Allow Listed Only”. A new dialog box will appear.
PAGE 7
QUICK START USER GUIDE NW10[E] TYPICAL POINT-TO-POINT CONFIGURATIONS Ethernet 1Gbps Ethernet NW10 (Access Point) NW10 (Client) P1 PoE 1Gbps Ethernet PoE Camera .. .. ..
PAGE 8
QUICK START USER GUIDE NW10[E] AGENCY COMPLIANCE FCC Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation.
PAGE 9
QUICK START USER GUIDE NW10[E] Need Additional Assistance? Visit our website http://www.comnet.net or contact Comnet tech support: Tel: (203) 796-5300 Toll free: (888) 678-9427 Email: techsupport@comnet.net Additional Technical support contact details can be found at: http://www.comnet.net/services/technical-support.html Or Visit our pre-sales design center: http://www.comnet.net/services/design-center.html Or our customer care: http://www.comnet.net/services/customer-care.