Data Sheet

ManualsBrandsComnet ManualsElectronicsNetWave Point-to-Multipoint Wireless Ethernet Link

LIFETIME WARRANTY WWW.COMNET.NET TECH SUPPORT: 1.888.678.9427

FEATURES

› Lifetime Warranty

› Up to 95Mbps Throughput

› 802.11a/n Compliant

› Distances up to 2 mi (FCC) or 2km (ETSI)

› Powered by the included power injection module or by an

IEEE802.3af PoE compliant device

› Environmentally Hardened -40º to +75ºC

› Meets class IP67 dust and water immersion protection

standards

› ETSI Standards (EU Region only):

– DFS Dynamic Frequency Selection

– TPC Transmit Power Control

› Secure transmission: WPA2 – AES or TKIP encryption

› ComNet Antenna alignment feature eases installation and

setup

› RF Spectrum Survey Tools

› Antenna Alignment Tools

› LED array displays unit operational status along with

received signal strength

APPLICATIONS

› Point to Multi-Point topologies whereby several Clients

connect to one Access Point

› Simple to deploy and cost-effective alternative to physical

connections to Ethernet edge equipment

› Integration of Ethernet where right-of-way issues mandate

wireless communications

› ITS traffic signalization networks and Video Detection

Systems (VDS)

› ITS roadside and city center CCTV surveillance, and

surveillance of high-value or mission-critical assets

› Wireless communications in manufacturing, petrochemical

refineries, wastewater treatment facilities, and other

industrial automation and control applications operating in

harsh or out-of-plant environments

› Electrical substation video and perimeter surveillance

The NetWave® industrially hardened wireless Ethernet transmission link can be

configured through the embedded User Interface as a Client or as an Access Point.

This point-to-multipoint model allows multiple Ethernet endpoints to be connected

to a central Access Point. Up to 15 endpoints can be linked to a central access point.

The NW1 and NW2 support up to 95Mbps throughput using MIMO technology.

The units can be powered by an IEEE 802.3af PoE compliant device or through the

supplied power injection module. The NW1 is FCC certified for use in North America

and the NW2 is ETSI, DFS and TPC certified for use in the European Union.

NW1/NW2

Industrially Hardened Point-to-Multipoint

Wireless Ethernet Link

2IP67-40º TO 75ºCINCLUDED 802.3af

Summary of content (3 pages)

PAGE 1
Industrially Hardened Point-to-Multipoint Wireless Ethernet Link NW1/NW2 INCLUDED -40º TO 75ºC 802.3af IP67 2 The NetWave® industrially hardened wireless Ethernet transmission link can be configured through the embedded User Interface as a Client or as an Access Point. This point-to-multipoint model allows multiple Ethernet endpoints to be connected to a central Access Point. Up to 15 endpoints can be linked to a central access point.
PAGE 2
Industrially Hardened Point-to-Multipoint Wireless Ethernet Link NW1/NW2 SPECIFICATIONS Wireless Radio EIRP NW1 (FCC): Up to +36dBm for point to multipoint deployments, +45dBm for point to point deployments with MAC-lock feature enabled NW2 (ETSI): +30dBm RF Output +26dBm Rated Transmitter Operational Frequency 5180MHz – 5825MHz, Region-dependent. Not all frequencies are supported in all regions. Contact ComNet for frequencies supported in your region.
PAGE 3
Industrially Hardened Point-to-Multipoint Wireless Ethernet Link NW1/NW2 TYPICAL APPLICATION NW1 (Client) Ethernet PIM or other PSE device Ethernet Power Point-to-Multipoint Topology PoE NW1 (Client) 10/100 Ethernet PC NVR ComNet Gigabit Managed Switch with 30W PoE+ PoE Ethernet IP Camera PIM or other PSE device Ethernet PoE IP Camera NW1/IA870 (Recommended Access Point) NW1 (Client) Ethernet Power PIM or other PSE device Ethernet PoE Power IP Camera Legend Wireless Power CAT5 Eth