Installation Manual

ManualsBrandsComnet ManualsFiber ConverterElectrical Substation-Rated Media Converter

INS_RLMC1005_REV–

Rev. 27 Jun 2016

INSTALLATION AND OPERATION MANUAL

RLMC1005 Series

Electrical Substation-Rated 10/100 Mbps Ethernet

Electrical To ST Optical Media Converter

The ComNet RLMC1005 is designed for deployment in environments where high

levels of electromagnetic noise and interference (EMI) and severe voltage transients

and surges are routinely encountered.

User-selectable link fault pass-through provides remote indication of a network fault,

and a summary fault alarm provides a local or remote indication via Form C dry

contact closure in the event of loss of optical link or operating power.

The 10/100BASE-TX port supports both auto-negotiation and automatic MDI/MDI-X

crossover for full and half-duplex operation; manual MDI/MDI-X switching is not

required.

LED indicators confirm operational status.

See Figures 1 – 6 for complete operation details.

The RLMC1005 is DIN-rail or panel-mountable. See Figure A on the last page for

mounting instructions.

This manual serves the following

ComNet Model Numbers:

RLMC1005M2/24DC

RLMC1005S2/24DC

RLMC1005M2/48DC

RLMC1005S2/48DC

RLMC1005M2/HV

RLMC1005S2/HV

Summary of content (5 pages)

PAGE 1
INSTALLATION AND OPERATION MANUAL RLMC1005 Series Electrical Substation-Rated 10/100 Mbps Ethernet Electrical To ST Optical Media Converter This manual serves the following ComNet Model Numbers: RLMC1005M2/24DC RLMC1005S2/24DC RLMC1005M2/48DC RLMC1005S2/48DC RLMC1005M2/HV RLMC1005S2/HV The ComNet RLMC1005 is designed for deployment in environments where high levels of electromagnetic noise and interference (EMI) and severe voltage transients and surges are routinely encountered.
PAGE 2
INSTALLATION AND OPERATION MANUAL Figure 1 – RLMC1005(M,S)2 Series Front Panel RLMC1005 Series Figure 2 – RLMC1005(M,S)2/24DC and Figure 3 – RLMC1005(M,S)2/HV RLMC1005(M,S)2/48DC Bottom Panel Bottom Panel 6 6 5 8 8 7 2 7 9 9 3 1 4 9 Table 1 – RLMC100524DC Physical Feature Descriptions Call-out Description Manual Reference 1 Unit Model Number (Be sure to refer to any specific instructions for your unit variation) – 2 10/100 Mbps Fiber Optic Port See Installation Instructions, Step 5
PAGE 3
INSTALLATION AND OPERATION MANUAL RLMC1005 Series Installation Instructions Figure 4 – DIP Switches DIP Switches on RLMC1005(M,S)2/24DC and RLMC1005(M,S)2/48DC Models DIP Switches on RLMC1005(M,S)2/HV Model Table 2 – DIP Switch Settings SW NAME OFF (DOWN) ON (UP) 1 Link Fault Enable Port 1 Link Fault Pass-Through Disabled Link Fault Pass-Through Enabled 2 N/A N/A N/A 3 FFE Fiber Fault Relay Disabled Fiber Fault Relay Enabled 4 PS Fault Enable Power Supply Fault Relay Disabled Power
PAGE 4
INSTALLATION AND OPERATION MANUAL RLMC1005 Series Installation Instructions (Continued) 7 - VERIFY FUNCTIONALITY See LED Indicator table below and Troubleshooting Guide if corrective action is needed. Table 4 – Front Panel LED Indicators Fiber Optic Link Fiber Optic Speed Fault Power Solid Communication link has been established over optical fiber. Flashes when data is being transmitted.
PAGE 5
MECHANICAL INSTALLATION INSTRUCTIONS Installation Considerations This product is supplied as Standalone/Surface Mount module. Units should be installed in dry locations protected from extremes of temperature and humidity. WARNING: Unit is to be used with a Listed Class 2 power supply. IMPORTANT SAFEGUARDS: A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.