User Manual

ManualsBrandsCOMPAL ManualsOtherCOMPAL GWT9R The Pixel Watch

What’s in the box

● Device

● Charging Cable

How to Set Up the Device

1. Press and hold the crown on the device for 3 seconds.

2. Unlock your phone and turn on Bluetooth. Connect the device with your phone

through Bluetooth.

3. Follow the setup instructions on your phone to finish the setting up.

How to Charge the Device

1. Plug the Magnetic Charging Cable into a USB power adapter.

2. Plug the adapter into a power outlet. Or plug the charging cable into a USB port

directly.

3. Position the back of your device on the charger. The charger's magnets align your

device, and you'll see the battery charging icon on the screen of the device.

WARNING: HEALTH AND SAFETY INFORMATION

To avoid damaging your device, accessories or any connected devices, and to reduce the risk

of personal injury, discomfort, property damage or other potential hazards, follow these

precautions below :

● Handle your Magnetic Charging Cable with care. You may damage the device if you

disassemble, drop, bend, burn, crush or puncture your device. Using a damaged

Magnetic Charging Cable, damaged cables or power adapter or charging when

moisture or debris is present, may cause overheating, fire, electric shock, injury or

damage to your charging cable or other property. Do not expose your USB-C Magnetic

Charging Cable to liquids, which can cause a short circuit and overheating. If the

charging cable gets wet, do not attempt to dry it using an external heat source. Your

Magnetic Charging Cable is designed to work best in ambient temperatures between

32° and 95° F (0° and 35° C), and should be stored between ambient temperatures of -

4° and 113° F (-20° and 45° C). Do not expose your Magnetic Charging Cable to

temperatures above 113° F (45° C) as this may damage the product and pose a risk of

fire. Avoid using the wireless charger in direct sunlight.

Summary of content (5 pages)

PAGE 1
What’s in the box ● Device ● Charging Cable How to Set Up the Device 1. Press and hold the crown on the device for 3 seconds. 2. Unlock your phone and turn on Bluetooth. Connect the device with your phone through Bluetooth. 3. Follow the setup instructions on your phone to finish the setting up. How to Charge the Device 1. Plug the Magnetic Charging Cable into a USB power adapter. 2. Plug the adapter into a power outlet. Or plug the charging cable into a USB port directly. 3.
PAGE 2
● This product must be used with a certified AC adapter with Limited Power Source (LPS) output per IEC 60950-1 and/or PS2 classified output per IEC 62368-1, rated: 5 Volts 1 Amp. Failure to use compatible accessories can cause fire, electric shock, injury, or damage to the Magnetic Charging Cable and the accessories. ● Be sure the power adapter and the charging cable are well ventilated when in use or charging.
PAGE 3
and dry your device after exposure to liquids.The charger and other accessories, including some wristbands are not water resistant and should not be exposed to liquids. EMC compliance statement Important: This device, and other in-box accessories have demonstrated Electromagnetic Compatibility (EMC) compliance under conditions that included the use of compliant peripheral devices and shielded cables between system components.
PAGE 4
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.
PAGE 5
Le présent appareil est conforme aux CNR d'IC Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes; 1. l'appareil ne doit pas produire de brouillage, et 2. l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.