Owner's Manual 3/8" Cordless Drill 184.10184-1 CAUTION: Before using this cordless drill or any of its accessories, read this manual and follow • • • • • Safety Instructions Assembly Operation Maintenance Parts List all its Safety Rules and Operating Instructions. • Espanol Sears, Roebuck Part No. 18410184-100! and Co., Hoffman Rev. O 10/05/03 Estates, IL 60179 U.S.A.
SECTION PAGE Warranty .......................... 2 Product Specifications ........ 3 Power ToolSafety............. 4 - 6 DrillSafety ....................... 6 Battery &Charger Safety.... 6- 7 Symbols .......................... 7 SECTION Know YourCordless Drill... Accessories ................... Carton Contents .............. Assembly &Operation ...... Maintenance ................... Parts& Service ................
DRILL Chuck ......................... 3/8" Switch ......................... No Load Speed ............. Reversible .................... Clutch ......................... Keyless Variable Speed 0 - 550 RPM Yes 16 + 1 16 Positions BATTERY ADDITIONAL If you require place & plus Drill Mode & CHARGER Battery Voltage ............... Charger ......................... Charger Input .................. 14.4 V 3-5 Hour, Class 2 120 V AC, 60 Hz Charger 17V DC, 400mA Output ...............
GENERAL [_L SAFETY RULES Do not abuse the to carry the tools outlet. Keep cord WARNING] Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, serious personal injury. fire and/or WORK AREA Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. cord. Never use the cord or pull the plug from away from heat, oil, an sharp edges or moving parts. Replace damaged cords immediately.
TOOLUSEANDCARE SERVICE Useclampsor otherpracticalwayto secureandsupportthe workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the tool if the switch does Tool service must be performed only by qualified personnel.
SPECIFIC SAFETY RULES - cont'd • TO AVOID INJURY from accidental starting, always remove the battery from the tool before installing or removing a drill bit, saw blade, sandpaper, DO NOT install or use any drill exceeds 7" (175mm)in length more than 6" (150mm) beyond jaws. They can suddenly bend • Do not charge the battery if it is wet or shows any evidence of corrosion. A small leakage from the battery may occur under extreme usage, charging or temperature conditions.
Other batteries may explode. Do not operate charger if cord or plug is damaged. Replace damaged cord and plug immediately.
Kg Donotoperate charger ifithasreceived asharpblow,beendropped orotherwise damaged inanyway.Haveaqualified technician examine thecharger and repairitifnecessary. Donot disassemble thecharger. Forbestresults, donotcharge the battery whenthebattery orair temperature isbelow50°F(10°C) or above105°F (40°C). • Unplug thecharger whennotinuseand before cleaning ormaintenance. • Donotabusethecord.Toreduce the riskofdamage totheelectric cordor plug,nevercarrythecharger bythecord oryankthecordtopulltheplug.
Screwdriver Storage Keyless Chuck Clutch Forward / Reverse Switch Trigger Switch Battery Bit
CARTON CONTENTS - cont'd 4 in 1 TOOL COMPONENTS CESSORIES KEY A Use only accessories recommended for this cordless drill. Follow instructions that accompany accessories. Use of improper accessories may cause injury to the operator or damage to the cordless drill. Visit a Sears Hardware Store or see the Sears Department or Power and Hand Tool Catalog for an assortment of accessories recommended for use with this cordless drill. C D • • Drill bits Screwdriver [_.
CHARGING THE 1. BATTERY Place the charging stand 110-120V/60Hz electrical near a outlet. Insert small charger plug (1) into charger stand (2) and plug the battery charger (3) into the 110-120V/60Hz wall receptacle (see Fig. 1 ). NOTE: The green come ON. indicator light (4) will Turn the battery (5) upside down and slide it into the matching slots in the charger stand. NOTES: a) Make sure the battery slides fully into the slots in the charger.
INSTALLING BATTERY IN TOOL Remove the discharged battery (1) from the tool by pressing on the battery release buttons (2) on each side of the battery and pulling the battery out of the tool handle (3) (see Fig. 2). 2. Slide the fully charged battery into the matching slots in the tool handle where the discharged battery has been removed. NOTE: Make sure the battery is fully engaged with the mounting slots in the tool handle.
SCREWDRIVER BIT STORAGE 2 Convenient screwdriver bit storage (1) is provided at the rear of the drill housing (see Fig. 3). 1 Fig. 4 \ Fig. 3 FORWARD/REVERSE TORQUE ADJUSTMENT Your drill is equipped with an adjustable torque clutch for driving different types of screws into different types of materials. The proper setting depends upon the type of material and size of screw being used.
fastest speed when the trigger switch is fully depressed. 2. To stop the drill, release switch.
NOTE: Drilling ataslowdrilling speedforan extended period oftimemaycause thedrill motororthebattery packtooverheat. Ifthe drillorbattery gethot,stopdrillingandallow ittocoolfor_at_least_t5 rr _utes. Finish tightening the chuck jaws by holding the chuck collar with one hand and firmly tightening the chuck body by rotating it in a clockwise direction. NOTE: Hand tighten chuck jaws. Do NOT use pliers. 2-.. ___1 1 3 Fig. 6 _ oi Fig.
Check drill bit to make sure it is firmly locked into the drill chuck and the forward/reverse switch is in the forward I WARN'NG I Have you read "POWER TOOL SAFETY", "DRILL SAFETY", "BATTERY & CHARGER SAFETY" position. 2. and "SYMBOLS" on pages 4, 5, 6 & 7 of this Manual? If not, please do it now before you operate this drill. Your safety depends clutch to highest setting. Hold the drill firmly with both hands whenever possible.
forjamming.
DRIVING SCREWS Tap the hex key sharply in a clockwise direction. When driving screws, care must be taken to use the bit that correctly fits the screw being driven. Make sure you use the largest bit size that will properly fit into the head of the screw. loosen the screw removal. 1. Select the correct screwdriver screw being driven. 2. Fasten the screwdriver bit into the chuck, making sure the flats of the bit are gripped by the chuck jaws.
RETIGHTENING LOOSE CHUCK After installing the chuck once it has been removed, the chuck may become loose on the spindle and develop a wobble. Also, the chuck screw may become loose causing the chuck jaws to bind and prevent them from closing. To tighten the chuck, follow these When servicing, use only identical Companion® replacement parts. Use of any other part may create a hazard or cause product damage. steps: 1. Insert hex key into chuck and tighten chuck securely.
Cordless Drill \ \ \ \
Cordless Drill In wA..,.G I When servicing, create a HAZARD Any attempt unless use only or cause to repair repair Companion damage or replace is performed ® replacement to your electrical by a qualified parts. power parts Use of any other parts may tool. on this power tool may create technician. Always order by PART NUMBER, not by key number.