319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM b Reference Guide Compaq Notebook Series Document Part Number: 319954-001 November 2003 This guide explains how to set up, operate, maintain, and troubleshoot your notebook. It also provides information on battery pack and power management, external device connections, and modem and network connections. The last chapter provides additional reference material on modem commands, safety, and regulatory information.
319954-001.book Page ii Thursday, February 3, 2005 3:03 PM © 2003 Hewlett-Packard Development Company, L.P. Microsoft, MS-DOS, and Windows are trademarks of Microsoft Corporation in the U.S. and/or other countries. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
19954-001.book Page iii Thursday, February 3, 2005 3:03 PM Software Product License Agreement Your Hewlett-Packard product contains software programs. CAREFULLY READ THIS LICENSE AGREEMENT BEFORE PROCEEDING TO OPERATE THIS EQUIPMENT. RIGHTS IN THE SOFTWARE ARE OFFERED ONLY ON THE CONDITION THAT THE CUSTOMER AGREES TO ALL TERMS AND CONDITIONS OF THE LICENSE AGREEMENT. PROCEEDING TO OPERATE THE EQUIPMENT INDICATES YOUR ACCEPTANCE OF THESE TERMS AND CONDITIONS.
319954-001.book Page iv Thursday, February 3, 2005 3:03 PM Software Product License Agreement Operating system and software applications by Microsoft are licensed to you under the Microsoft License Agreement contained in the Microsoft documentation or displayed on your screen when Microsoft Software Products are launched.
319954-001.book Page v Thursday, February 3, 2005 3:03 PM Software Product License Agreement PRODUCT RECOVERY CD-ROM or DVD. If your HP product was shipped with a product recovery CD-ROM or DVD: (i) The product recovery CD-ROM or DVD and/or support utility software may be used only for restoring the hard disk of the HP product with which the product recovery CD-ROM or DVD was originally provided.
319954-001.book Page vi Thursday, February 3, 2005 3:03 PM Software Product License Agreement U.S. GOVERNMENT RESTRICTED RIGHTS. Use, duplication, or disclosure is subject to HP standard commercial license terms and, for non-DOD Departments and Agencies of the U.S. Government, the restrictions set forth in FAR 52.227-19(c)(1-2) (June 1987) Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304 U.S.A. Copyright © 2000 Hewlett-Packard Company. All Rights Reserved.
319954-001.book Page vii Thursday, February 3, 2005 3:03 PM Contents Software Product License Agreement 1 Getting Started with Your Notebook Identifying Parts of the Notebook . . . . . . . . . . . . . . . . . . 1–1 Front Panel and Right Panel Components . . . . . . . . 1–2 Left Panel and Back Panel Components . . . . . . . . . . 1–4 Bottom Panel Components . . . . . . . . . . . . . . . . . . . . 1–6 Status Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–8 Setting Up Your Notebook. .
319954-001.book Page viii Thursday, February 3, 2005 3:03 PM Contents To Type Alternate Graphics Using the ALT GR Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9 Using CDs or DVDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–10 To Insert or Remove a CD or DVD. . . . . . . . . . . . . 2–10 To Play DVD Movies . . . . . . . . . . . . . . . . . . . . . . . 2–11 To Create or Copy CDs . . . . . . . . . . . . . . . . . . . . . . 2–11 To Write to DVD Media . . . . . . . . . . . . . . .
319954-001.book Page ix Thursday, February 3, 2005 3:03 PM Contents 4 Modem and Network Connections Using the Modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1 To Connect the Modem . . . . . . . . . . . . . . . . . . . . . . . 4–2 Special Restrictions in Certain Countries . . . . . . . . . 4–3 To Change Your Modem Settings . . . . . . . . . . . . . . . 4–4 Connecting to a Local Area Network (LAN). . . . . . . . . . 4–5 Using a Wireless LAN Adapter . . . . . . . . . . . . . . . . . . .
319954-001.book Page x Thursday, February 3, 2005 3:03 PM Contents Heat Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6 Infrared Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–6 Keyboard and Pointing Device Problems . . . . . . . . . 6–6 Local Area Network (LAN) Problems . . . . . . . . . . . 6–8 Memory Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–9 Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . .
319954-001.book Page xi Thursday, February 3, 2005 3:03 PM Contents Exposure to Radio Frequency Radiation . . . . . . . . . Wireless Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . European Union. . . . . . . . . . . . . . . . . . . . . . . . . . . . Japan . . . . . .
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 1 Getting Started with Your Notebook Identifying Parts of the Notebook Components included with the notebook may vary by geographical region and the features you selected. The following illustrations identify the standard external components included with most notebook models. Reference the illustrations that closely match your notebook.
319954-001.
319954-001.
319954-001.
319954-001.
319954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Bottom Panel Components 1 Hard drive 4 Reset button 2 Battery latch 5 Docking port (select models only) 3 RAM (memory) cover 6 Mini PCI cover (no user parts inside) Ä 1–6 CAUTION: The FCC does not allow unauthorized Mini PCI devices to be used in the notebook. Installing an unsupported Mini PCI device can prevent your notebook from operating properly and may result in a warning message.
319954-001.
319954-001.book Page 8 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Status Lights The notebook includes a number of status lights that report power and battery status, drive activity, and keyboard functions such as Caps Lock and Num Lock. The following diagram shows the main status lights on the front of the notebook. 1 Power mode ■ ■ ■ On: Notebook is on (even if the display is off). Blinking: Notebook is in Standby. Off: Notebook is off or in Hibernation.
319954-001.book Page 9 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook The keyboard status lights, located above the keyboard, indicate the states of the keyboard locks. 1 Caps Lock On: Caps Lock is active. 2 Num Lock On: Num Lock is active. (The Keypad Lock must also be on to use the embedded keypad.) 3 Keypad Lock On: The embedded keypad is active (Fn+F8). Num Lock must also be on to activate the numeric keys.
319954-001.book Page 10 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Setting Up Your Notebook Å WARNING: To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation setup, posture, and health and work habits for computer users, and provides important electrical and mechanical safety information. This guide is located on the Web at http://www.compaq.
319954-001.book Page 11 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Step 2: Connect AC Power Ä CAUTION: Use only the AC adapter included with your notebook (or other approved adapter that meets the power requirements of the notebook). Using the wrong AC adapter could damage the notebook or adapter, cause data loss, and may void your warranty. 1. Plug the AC adapter into the notebook. 2. Connect the power cord to the AC adapter. 3. Plug the power cord into a wall outlet.
319954-001.book Page 12 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Step 3: Connect a Phone Line 1. Make sure the telephone line is an analog line, sometimes called a data line. (Do not use a digital line.) 2. Connect the telephone cord (RJ-11) into a telephone jack. 3. Plug the other end of the telephone cord into the RJ-11 modem jack on the notebook. For details about using the modem, see “Using the Modem.
319954-001.book Page 13 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Step 4: Turn On the Notebook Press the power button above the left side of the keyboard. The notebook boots up, and Windows starts automatically. your notebook does not turn on when operating on ✎ Ifbattery power, the battery pack may be out of power. Plug in the AC adapter, then press the power button again. Leave the AC adapter plugged in for several hours to fully charge the battery pack.
319954-001.book Page 14 Thursday, February 3, 2005 3:03 PM Getting Started with Your Notebook Step 5: Set Up Windows Your notebook has the Microsoft Windows operating system preinstalled on its hard drive. The first time you turn on your notebook, the Windows Setup program runs automatically and includes opportunities to customize your setup. 1. Follow the Setup program instructions on the screen. If the program prompts you to enter the Product ID code, locate the code on the bottom of the notebook. 2.
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 2 Basic Operation Operating Your Notebook You can start and stop your notebook by using the power button. However, alternative methods may be required, depending on power considerations, types of active connections, and startup time. This chapter describes several of these methods.
319954-001.book Page 2 Thursday, February 3, 2005 3:03 PM Basic Operation Default Power Settings Power mode To enter this mode Function ON—Power status light is on. Briefly press the power button. Powers on the notebook. OFF—Power status light is off. Select Start > Turn Off Computer > Turn Off. If the system has stopped responding and Windows shutdown procedures cannot be used, press and hold the power button for 4 seconds to turn off the notebook. Powers off the notebook.
319954-001.book Page 3 Thursday, February 3, 2005 3:03 PM Basic Operation To Reset the Notebook Occasionally, Windows or the notebook may stop responding and you will not be able to turn off the notebook. If this happens, try the following procedures in the order listed: ■ If possible, shut down Windows. Press ctrl+alt+del, then select Shut Down > Restart. -or- ■ Press the power button for at least 4 seconds until the display shuts down. Unsaved data will be lost.
319954-001.book Page 4 Thursday, February 3, 2005 3:03 PM Basic Operation To Use the TouchPad The TouchPad includes an on-off button so you can turn off the TouchPad to avoid moving the pointer accidentally when you are typing. The indicator light turns off when you turn off the TouchPad. 1 Click buttons. The Click buttons work like the left and right buttons on a standard mouse. 2 TouchPad (touch-sensitive pointing device). 3 TouchPad on-off button and indicator light. 4 Scroll pad.
319954-001.book Page 5 Thursday, February 3, 2005 3:03 PM Basic Operation To Use the Tap to Click Function of the TouchPad The Tap to Click function of your TouchPad is not enabled by default. To enable it, follow the instructions included here: 1. Select Start > Control Panel > Printers and Other Hardware > Mouse. The Mouse Properties dialog box opens. 2. Select the Device Settings tab and then select the Settings button. 3. In the left panel, select Tapping. Then select the Enabling Tapping check box.
9954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Basic Operation To Use the Function Hot Keys The combination of the Fn key plus another key creates a hot key—a shortcut key sequence—for various system controls. To use a hot key, press and hold Fn, press the appropriate second key, then release both keys. 2–6 This hot key Does this Fn+F1 Decreases the display brightness. Fn+F2 Increases the display brightness. Fn+F8 Toggles the built-in keypad on and off.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Basic Operation To Use the One-Touch Buttons Your notebook includes 5 One-Touch buttons that can start any application or open a document or Web site by pressing a single key. Press a One-Touch button to open the corresponding application, document, or Web site. To program a One-Touch button: 1. Select Start > All Programs > Utilities > One-Touch. 2. On the One-Touch tab, select the button you want to reprogram. 3.
319954-001.book Page 8 Thursday, February 3, 2005 3:03 PM Basic Operation To Use the Windows and Applications Keys The Windows key brings up the Windows Start menu. This is the same as selecting the Start button on the taskbar. The Applications key brings up the shortcut menu for the selected item. This is the same menu that appears when you right-click while pointing at the selected item. 2–8 This key combination Does this Windows key+E Runs Windows Explorer. Windows key+F1 Runs Windows Help.
319954-001.book Page 9 Thursday, February 3, 2005 3:03 PM Basic Operation To Type Alternate Graphics Using the ALT GR Key Non-U.S. keyboards have an ALT GR key to the right of the spacebar and keys on the keyboard that show International characters. These special characters appear on the lower-right corner of some keys on the keyboard.
319954-001.book Page 10 Thursday, February 3, 2005 3:03 PM Basic Operation Using CDs or DVDs To Insert or Remove a CD or DVD Ä CAUTION: Do not remove a CD or DVD while the notebook is reading it, or the notebook could stop responding and you could lose data. To avoid damage to the disk or drive, be sure to press the CD or DVD firmly onto the spindle. ✎ The location of the CD or DVD drive varies by model. 1. Press the button on the face of the CD or DVD drive.
319954-001.book Page 11 Thursday, February 3, 2005 3:03 PM Basic Operation To Play DVD Movies If your notebook is equipped with a DVD or other DVD-readable drive, it also includes DVD player software that lets you play DVD movies. » Select Start > All Programs > Multimedia > DVD Player > InterVideo WinDVD. best performance while playing movies on battery power, set ✎ For the Control Panel Power Scheme to Portable/Laptop. can have regional codes embedded in the disc data.
319954-001.book Page 12 Thursday, February 3, 2005 3:03 PM Basic Operation To Write to DVD Media If your notebook is equipped with a DVD+RW/R and CDRW combo drive, you must install Roxio Easy CD Creator and Sonic My DVD software from the CDs included with your notebook before you can write to DVD media. When writing to DVD+R or DVD+RW media, observe the following guidelines: ■ Place the notebook on a flat, stable surface, and ensure that room temperature is below 90° F.
319954-001.book Page 13 Thursday, February 3, 2005 3:03 PM Basic Operation For complete protection, set passwords in Windows and through the BIOS Setup utility, see “Configuring Your Notebook” in the “Troubleshooting” chapter. To Lock Your Notebook To protect against unauthorized access while your notebook is running, lock the notebook before leaving it unattended, or set up a screen saver with a Windows password.
319954-001.book Page 14 Thursday, February 3, 2005 3:03 PM Basic Operation To Attach a Security Cable Your notebook includes a built-in connector to secure the notebook with a cable and a lock (such as the Kensington MicroSaver lock system, available at many computer stores). 1. Wrap the cable around a secure object. 2. Insert the cable into the security cable slot on the notebook. 3. Lock it with the cable lock key, then store the key in a safe place away from the notebook.
319954-001.book Page 15 Thursday, February 3, 2005 3:03 PM Basic Operation To Protect Against Viruses Virus-protection software can help protect the integrity of your data. This is especially important if you use the Web. Your notebook comes equipped with Norton AntiVirus software. Because new viruses appear frequently, you will also want to keep the program virus definitions up to date. Norton AntiVirus updates are on the Web at http://www.symantec.com.
319954-001.book Page 16 Thursday, February 3, 2005 3:03 PM Basic Operation Taking Care of Your Notebook Follow these recommendations to maintain your notebook during everyday use and prevent potential physical damage or data loss. To Protect Your Hard Drive Hard drives, as well as other internal components, are not indestructible and can be damaged by inappropriate handling and operation. ■ Avoid bumps or jolts. ■ Do not operate the notebook while traveling over bumpy terrain.
319954-001.book Page 17 Thursday, February 3, 2005 3:03 PM Basic Operation To Safeguard Your Data ■ Do not use a pointing device or activate any other device that interrupts operation while the system is starting or stopping. ■ Back up your work regularly. Copy files to diskettes, CDs, DVDs, and other media, or to network drives. ■ Use a virus-scanning program (such as the Norton AntiVirus program included with your notebook) to check your files and operating system.
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 3 Battery Packs and Power Management Managing Power Consumption When you are running your notebook on battery power, you can maximize operating time without compromising performance. Your notebook is designed to help you reduce power consumption and extend battery life. During idle periods, the notebook automatically enters power-saving modes after specified timeout periods. You can adjust these timeouts to suit your working habits.
319954-001.book Page 2 Thursday, February 3, 2005 3:03 PM Battery Packs and Power Management How the Notebook Manages Power Automatically Your notebook enters Hibernation and Standby automatically, and turns off the hard drive and display based on values set in Windows. When this occurs The result is To resume No keyboard, pointing device, or other input activity occurs for the specified interval. Display is turned off. Conserves battery power and extends the life of the display.
319954-001.book Page 3 Thursday, February 3, 2005 3:03 PM Battery Packs and Power Management To Change Timeout Settings and Create Power Schemes You can adjust the length of timeouts after which your notebook automatically shuts down components or enters a power-saving mode. You can also save these settings as a power scheme. 1. Select Start > Control Panel > Performance and Maintenance > Power Options. 2. Select the Power Schemes tab, then enter the settings you want.
319954-001.book Page 4 Thursday, February 3, 2005 3:03 PM Battery Packs and Power Management To Check Battery Status From the battery status light » Check the battery status light on the notebook. From the Windows taskbar The Windows taskbar can display a power icon that provides detailed battery status information (see Windows Help for details). The icon resembles a battery when a battery pack is the notebook’s sole source of power.
319954-001.book Page 5 Thursday, February 3, 2005 3:03 PM Battery Packs and Power Management To Respond to a Low-Battery Warning The notebook automatically alerts you when the battery power drops to a critically low level. The notebook first emits a high-pitched beep or displays a warning message. Then, if you do not restore power within a short time, the notebook goes into Hibernation.
319954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Battery Packs and Power Management To Get the Most from Your Battery Packs Follow these suggestions to make your battery power last as long as possible: ■ Plug in the AC adapter, especially when using a CD-ROM or DVD drive, or any external connections such as a PC Card or a modem. ■ Set the display brightness to the lowest comfortable level (Fn+F1). ■ Put the notebook in Standby when you will not be using it for a short while.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Battery Packs and Power Management ■ To preserve the life of a battery pack, be sure to charge it regularly. ■ If the notebook will be unused and unplugged for more than 2 weeks, remove and store the battery pack. Ä To prevent damage to the battery pack, do not expose it to high temperatures for extended periods of time. ■ High temperatures accelerate the self-discharge rate of a stored battery pack.
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 4 Modem and Network Connections Using the Modem You can connect your modem to a telephone line and communicate throughout the world. You can explore the Internet, send and receive e-mail messages, and use your notebook to send and receive faxes.
319954-001.book Page 2 Thursday, February 3, 2005 3:03 PM Modem and Network Connections To Connect the Modem Ä 4–2 CAUTION: Your built-in modem may not work with multiple phone lines or a private branch exchange (PBX). It cannot be connected to a coin-operated telephone and does not work with party lines. Some of these connections may result in excess electrical voltage and could cause a malfunction in the internal modem. Check your telephone line type before connecting your phone line.
319954-001.book Page 3 Thursday, February 3, 2005 3:03 PM Modem and Network Connections Special Restrictions in Certain Countries ■ Many countries impose a blackout period after a modem repeatedly fails to connect to a service provider. The number of failed attempts and the period you must wait before trying again differ from country to country. Check with your telephone company.
319954-001.book Page 4 Thursday, February 3, 2005 3:03 PM Modem and Network Connections To Change Your Modem Settings The modem is already set up to be compatible with telephone systems and modems in most areas. However, in some situations, you may have to change modem settings to match local conditions. If you have questions about local requirements, contact your telephone company. ■ Control Panel. Open Phone and Modem Options in Control Panel to change many modem settings.
319954-001.book Page 5 Thursday, February 3, 2005 3:03 PM Modem and Network Connections Connecting to a Local Area Network (LAN) You can connect to local area networks (LANs). LANs give you access to network resources, such as printers and file servers on your corporate network, and possibly to the Internet. To connect to a LAN: 1. Check that the existing LAN supports Ethernet 10Base-T (10 Mbps) or 100Base-TX (100 Mbps) connections. 2. Plug the LAN cable (not supplied) into the built-in LAN port.
319954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Modem and Network Connections Using a Wireless LAN Adapter Your notebook model may include a wireless local area network (WLAN) adapter. A WLAN adapter enables your notebook to connect to a compatible wireless network access point or to another, compatible, wireless-enabled notebook. A WLAN adapter cannot be used to connect the notebook to a mobile telephone service, a Bluetooth wireless device, or a cordless telephone.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Modem and Network Connections To use a wireless LAN connection: 1. Verify that all drivers required by the WLAN adapter are installed and that the WLAN adapter is correctly configured. If you are using an integrated WLAN adapter, all required drivers are installed and the adapter is preconfigured and ready for use. 2. If you are using an integrated WLAN adapter, verify that it is enabled.
319954-001.book Page 8 Thursday, February 3, 2005 3:03 PM Modem and Network Connections Making Wireless Network Connections (Select Models Only) If your notebook includes a wireless on-off button, you can connect by radio to an 802.11 wireless local area network (LAN) and access computers and other resources on the network. A wireless network provides all the functions of a typical “wired” network, but also provides for “roaming.
319954-001.book Page 9 Thursday, February 3, 2005 3:03 PM Modem and Network Connections To Prepare for Connections Before you can connect your notebook to an existing 802.11 wireless network, you need to configure the notebook for the specific wireless connection. Connecting to a Wireless Network You can connect to an access point that gives you access to a local area network, or you can connect directly to other computers in an “ad hoc” network. Before you can connect your notebook to an existing 802.
319954-001.book Page 10 Thursday, February 3, 2005 3:03 PM Modem and Network Connections 4. Type a name for the new network. 5. If you want to use encrypted communication, clear the automatic key option, then select the following parameters: ❏ Key: ASCII passphrase or hexadecimal key string. ❏ Key format: ASCII for passphrase, hexadecimal for key string. ❏ Key length: smaller number for 64-bit encryption, larger number for 128-bit. 6.
319954-001.book Page 11 Thursday, February 3, 2005 3:03 PM Modem and Network Connections Turning On Communication and Making a Connection If your notebook has wireless 802.11 capabilities, the wireless indicator light on the front of the notebook turns on when 802.11 communication is turned on. 1. If the notebook is not on, turn it on. 2. If you normally press the wireless on-off button on the front of the notebook to turn wireless 802.
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 5 Add-On Devices Connecting External Devices To Insert or Remove a PC Card The notebook PC Card slot supports standard Type II and Type III PC Cards (PCMCIA and CardBus). location and number of the PC Card slots vary by model ✎ The series. Inserting a PC Card 1. Hold the PC Card label side up and its connectors facing the card slot. 2. Aligning the PC Card along the bottom of the slot, slide the PC Card until it is seated.
319954-001.book Page 2 Thursday, February 3, 2005 3:03 PM Add-On Devices Removing a PC Card Ä CAUTION: Before removing a PC Card, you must use the Eject Hardware or Safely Remove Hardware icon in the taskbar, or shut down the notebook. Otherwise, you could lose data. 1. Select the Eject Hardware or Safely Remove Hardware icon in the taskbar, select the card you want to remove, then remove the card. This protects your data and helps avoid unexpected problems.
319954-001.book Page 3 Thursday, February 3, 2005 3:03 PM Add-On Devices To Connect an Audio Device You can plug in an external microphone, external speakers, or headphones. In addition, if you connect your notebook to the port replicator, you can plug in a stereo source (such as a CD player) or a device that accepts digital audio (such as a digital audio recorder). Ä CAUTION: The headphone and line-in jacks are three-terminal stereo jacks. They are not compatible with two-terminal mono plugs.
319954-001.book Page 4 Thursday, February 3, 2005 3:03 PM Add-On Devices To Use an External Monitor Connecting an External Monitor 1. Plug a standard 4-pin S-Video cable to the S-Video out jack on your notebook (yellow connector on the back panel). Plug the other end of the cable to the S-Video in jack on your television. Restart your notebook. ✎ Although your notebook has a 7-pin S-Video out jack, the notebook accepts either a 7-pin or 4-pin cable connection. 2.
319954-001.book Page 5 Thursday, February 3, 2005 3:03 PM Add-On Devices Using Dual Display Mode You can extend your desktop by connecting an external monitor to your notebook. 1. Select Start > Control Panel > Appearance and Themes > Display. 2. Select the Settings tab. 3. Select the second display, then select the option to extend the desktop. You can set different resolutions and numbers of colors for each display. However, using the Extended Desktop requires video memory for each display.
319954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Add-On Devices To Connect a 1394 Device (Select Models Only) If your notebook has a 1394 port (also known as FireWire), you can use it to connect devices such as audio and video equipment, disk drives, printers, and other notebooks. Attach the device cable to the 1394 port. Windows automatically recognizes the device. The 1394 port is a 4-wire port.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Add-On Devices Using the Infrared Port ■ Make sure the infrared port of your notebook and the infrared port of the device with which you want to communicate are positioned in a straight line facing each other. The 2 ports should be no more than (1 meter) 3.3 feet apart with no obstructions in between. Noise from nearby equipment can cause transmission errors.
319954-001.book Page 8 Thursday, February 3, 2005 3:03 PM Add-On Devices To Use a Port Replicator (Select Models Only) A port replicator provides your notebook with external connections that you can leave in place whenever you remove the notebook. Instead of disconnecting and reconnecting peripheral devices, you can simply undock and dock the notebook. Ä CAUTION: Use only the approved AC adapter that meets the power requirements of the notebook.
319954-001.book Page 9 Thursday, February 3, 2005 3:03 PM Add-On Devices 3. Align the notebook with the locator posts on the port replicator. 4. Press the notebook down until it snaps into place. 5. If the notebook is off, open the notebook and press the power button to turn it on. The lights on the port replicator turn on. When the notebook is docked, you can use the notebook security connector to secure the notebook.
319954-001.book Page 10 Thursday, February 3, 2005 3:03 PM Add-On Devices To Undock from the Port Replicator 1. Press down the undock button on the right side of the port replicator. 2. Lift the notebook out of the port replicator.
319954-001.book Page 11 Thursday, February 3, 2005 3:03 PM Add-On Devices Installing Additional RAM (Memory) The notebook has 2 slots that hold 2 RAM modules. At least one slot contains a RAM module installed at the factory. You can use both slots to expand your RAM. To Install a RAM Expansion Module Use only PC2100 DDR-266-MHz or higher RAM. You will need a small Phillips screwdriver for these steps.
319954-001.book Page 12 Thursday, February 3, 2005 3:03 PM Add-On Devices 7. Replace the cover. 8. Insert the battery pack.
319954-001.book Page 13 Thursday, February 3, 2005 3:03 PM Add-On Devices To Remove a RAM Expansion Module You may want to remove a RAM module so you can install a larger one. You will need a small Phillips screwdriver for these steps. Ä CAUTION: Your notebook internal components are extremely sensitive to static electricity and can be permanently damaged by it. Handle the RAM module only by its edges.
319954-001.book Page 14 Thursday, February 3, 2005 3:03 PM Add-On Devices 7. Pull the board out of the connector. 8. Replace the cover. 9. Insert the battery pack. Replacing the Hard Drive To Replace the Hard Drive You will need a small Phillips screwdriver for this procedure. 1. Save your work and shut down the notebook. If you are not sure whether the notebook is off or in Hibernation, briefly press the power button.
319954-001.book Page 15 Thursday, February 3, 2005 3:03 PM Add-On Devices 6. Match your notebook to one of the following illustrations. Use a pointed tool to remove the plugs from the 2 or 3 screw holes, then remove the screws. The number of screws varies by model. 7. Gently pull the hard drive out of the notebook. 8. Gently slide the new drive into the hard drive compartment. Press firmly to make sure the connector seats properly. 9. Reinstall the hard drive screws and plugs.
319954-001.book Page 16 Thursday, February 3, 2005 3:03 PM Add-On Devices To Replace the Hard Drive Holder If you are installing a new hard drive that does not have a holder, you can remove the holder parts from the hard drive you are removing. You will need a small Phillips screwdriver for this procedure. 1. Remove the 4 screws from the sides of the holder and drive case, then slide the drive out of the holder. 2. Notice that the hard drive has a pin connector attachment at one end.
319954-001.book Page 17 Thursday, February 3, 2005 3:03 PM Add-On Devices To Prepare a New Hard Drive When you install a new hard drive, you also need to prepare it to be able to work with your notebook. If you want to restore the Windows software and operating system that were originally installed on your notebook, follow the system recovery procedures described in the “Troubleshooting” chapter of this guide.
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 6 Troubleshooting Troubleshooting Your Notebook This chapter contains solutions to many types of problems you might have with your notebook. Try the solutions one at a time, in the order in which they are presented. Here are some other sources of information for troubleshooting: ■ Use the Windows troubleshooters. Select Start > Help and Support. ■ Select the question mark One-Touch key located at the top of the keyboard.
319954-001.book Page 2 Thursday, February 3, 2005 3:03 PM Troubleshooting Audio Problems If No Sound Is Audible ■ If your model has a volume control, press the + (plus) button to increase the volume. ■ Select the speaker icon on the taskbar (if present). Clear the Mute all check box if selected. If your model has an audio mute button, press it so the indicator light goes off.
319954-001.book Page 3 Thursday, February 3, 2005 3:03 PM Troubleshooting CD-ROM and DVD Problems If You Cannot Boot from a CD or DVD ■ Make sure the CD or DVD is bootable. ■ Make sure the CD-ROM/DVD drive is selected as the boot device. See the “Basic Operation” chapter in this guide to change the boot sequence. ■ Restart the notebook by selecting Start > Turn Off Computer > Restart. If a DVD Plays Erratically ■ Dirt or smudges can cause a disc to skip. Clean the disc with a soft cloth.
319954-001.book Page 4 Thursday, February 3, 2005 3:03 PM Troubleshooting ■ Restart the system: remove the disc from the drive, and select Start > Turn Off Computer > Restart. ■ If you created the CD on a DVD/CDRW combo-type drive, try using a different media brand. Read and write quality may vary for media. If a DVD Movie Does Not Fill the Screen Each side of a double-sided DVD has a different format (standard or widescreen).
319954-001.book Page 5 Thursday, February 3, 2005 3:03 PM Troubleshooting ■ Install the driver or .inf file for your specific monitor ❏ Select the external monitor as the primary display device in the display properties ❏ Continue to toggle Fn+F5 until the external display is enabled. Hard Drive Problems If the Notebook Hard Drive Does Not Spin ■ Make sure the notebook has power.
319954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Troubleshooting Heat Problems Your notebook normally gets warm during routine operation. If the Notebook Gets Abnormally Hot ■ Always set the notebook on a flat surface, so that air can flow freely around and underneath it. ■ Make sure the air vents on the bottom and sides of the notebook are clear. ■ Keep in mind that games and other programs that drive CPU usage toward 100 percent can increase the notebook temperature.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Troubleshooting If the Pointer Is Difficult to Control ■ Adjust the pointer controls by selecting Start > Control Panel > Printers and Other Hardware > Mouse. ■ Ensure that your thumb or palm is not pressing or near the TouchPad on-off button while typing. ■ Use an external mouse if using the TouchPad is difficult. If the TouchPad Does Not Work ■ Press the TouchPad on-off button to turn on the light.
319954-001.book Page 8 Thursday, February 3, 2005 3:03 PM Troubleshooting Local Area Network (LAN) Problems If the Built-In Network Adapter Does Not Connect to the LAN ■ Check all cables and connections. Try connecting at a different network station, if available. ■ Make sure the LAN cable is Category 3, 4, or 5 for 10Base-T operation, or Category 5 for 100Base-TX operation. Maximum cable length is (100 meters) 330 feet. ■ Select Start > Help and Support > and use the Networking troubleshooter.
319954-001.book Page 9 Thursday, February 3, 2005 3:03 PM Troubleshooting Memory Problems If a Message Reports That You Are Out of Memory ■ Make sure drive C is not running low on free space. ■ If you are having memory problems while running MS-DOS programs, select Start > Help and Support. Use the MS-DOS or Application and Software troubleshooter in Windows Help. ■ The full amount of RAM in your notebook is not available for running applications. A certain amount of RAM is used for display memory.
319954-001.book Page 10 Thursday, February 3, 2005 3:03 PM Troubleshooting ■ Eliminate extra connections in the line. If possible, connect directly to the wall jack. ■ Try another telephone line, preferably one normally used for a fax machine or modem. If the Modem Does Not Dial or No Dial Tone Is Detected ■ Check all cables and connections. ■ Connect a standard telephone to the phone line and make sure the line is working. ■ Make sure someone else is not using the same phone line.
319954-001.book Page 11 Thursday, February 3, 2005 3:03 PM Troubleshooting If the Modem Dials, But Does Not Connect ■ Make sure you are using an analog telephone line (2, 3, or 4 wires). You must not use a digital line. In a hotel, ask for a data line. ■ Try another telephone line, preferably one normally used for a fax machine or modem. ■ The modem at the other end may have a problem. Try dialing to a different modem. If the Modem Is Not Detected ■ Check the modem setup.
319954-001.book Page 12 Thursday, February 3, 2005 3:03 PM Troubleshooting If the Modem Causes an ERROR Message A string of AT commands may contain an incorrect command. If you entered commands as extra settings for the modem in Control Panel or in your communications software, check the commands. If the Modem Does Not Fax ■ If you are using fax Class 2 in the fax software, try using Class 1. ■ Close any other communications programs.
319954-001.book Page 13 Thursday, February 3, 2005 3:03 PM Troubleshooting ■ Zoomed Video is not supported. ■ If the card requires an IRQ, make sure one is available. Open the hardware Device Manager. Select Start > Control Panel > Performance and Maintenance > System. If a Network PC Card Stops Communicating Properly ■ The card may have been reset if the notebook entered Standby or was shut down. Exit any applications, then remove and reinsert the card. ■ Check settings in the Control Panel.
319954-001.book Page 14 Thursday, February 3, 2005 3:03 PM Troubleshooting ■ Restart the notebook by selecting Start > Turn Off Computer > Restart. ■ Some file browsers respond slowly while processing graphics or waiting for broken network connections to time out.
319954-001.book Page 15 Thursday, February 3, 2005 3:03 PM Troubleshooting If the Notebook Keeps Beeping The notebook beeps repeatedly or displays a warning when battery power is low. Save your work, shut down Windows immediately, and insert a charged battery pack or plug in the AC adapter. If the Battery Pack Does Not Charge ■ Make sure the AC adapter is fully plugged into the power source and the notebook, and that the light on the adapter is on.
319954-001.book Page 16 Thursday, February 3, 2005 3:03 PM Troubleshooting ■ Heavy modem use can impact battery-operating time. ■ PC Card use can impact battery-operating time. ■ Test and recondition the battery pack every 3 months. If the Time Remaining for the Battery Pack Is Not Correct The Time Remaining is an estimate, not a precise value, and is based on the rate at which the notebook is using power at the moment.
319954-001.book Page 17 Thursday, February 3, 2005 3:03 PM Troubleshooting Printing Problems will be able to solve most printing problems by using the ✎ You Print troubleshooter in Windows Help. Select Start > Help and Support. If a Serial or Parallel Printer Does Not Print ■ Make sure the printer is on and has paper in it. ■ Make sure you are using the correct printer cable or cable adapter, and that the cable is secure at both ends. ■ Check for printer errors.
319954-001.book Page 18 Thursday, February 3, 2005 3:03 PM Troubleshooting Serial, Parallel and USB Problems If a Serial Mouse Does Not Work ■ Make sure you followed the manufacturer’s installation instructions completely and have installed the mouse properly. If not, repeat the procedure. ■ Make sure the port connection is secure. ■ Restart the notebook by selecting Start > Turn Off Computer > Restart.
319954-001.book Page 19 Thursday, February 3, 2005 3:03 PM Troubleshooting If the Serial or Parallel Port Is Not Working ■ Make sure the port connection is secure. ■ Check the port settings in Control Panel. Open the hardware Device Manager, then select Ports (COM & LPT). If the USB Port Is Not Working ■ Contact the vendor of the peripheral device for the latest USB drivers. ■ Check the port settings in Control Panel. Open the hardware Device Manager, then select Universal Serial Bus Controller.
319954-001.book Page 20 Thursday, February 3, 2005 3:03 PM Troubleshooting If the Notebook Will Not Boot from the Diskette Drive ■ Make sure the diskette drive is selected as the boot device. See the “Basic Operation” chapter in this guide for directions. ■ If you are using a USB diskette drive, use the BIOS Setup utility to make sure Legacy USB Support is enabled.
319954-001.book Page 21 Thursday, February 3, 2005 3:03 PM Troubleshooting Wireless Problems If You Have Problems with Wireless 802.11 Communication ■ Make sure the wireless indicator light is on. ■ If your notebook includes Bluetooth capabilities, make sure wireless 802.11 communication is turned on. Select Start > All Programs > Utilities > Wireless Configuration, then make sure that the 802.11 button is enabled. ■ Make sure you are using the correct SSID and channel settings.
319954-001.book Page 22 Thursday, February 3, 2005 3:03 PM Troubleshooting If You Have Trouble Connecting to Another Notebook in the Network Neighborhood or My Network Places ■ Wait a few minutes, then press F5 to refresh the list of notebooks on the network. ■ Select Start > Search > Notebooks or People to locate the notebook. If You Cannot Connect to a Particular Notebook on the Network ■ Make sure the notebook is properly connected to the network.
319954-001.book Page 23 Thursday, February 3, 2005 3:03 PM Troubleshooting Configuring Your Notebook The BIOS Setup utility helps you configure your notebook operation. To Run the BIOS Setup Utility The BIOS (basic input and output system) Setup utility enables you to make changes to the notebook system configuration and to tailor the operation of your notebook to your individual work needs.
319954-001.book Page 24 Thursday, February 3, 2005 3:03 PM Troubleshooting Main Menu 6–24 Setting Description Default BIOS Revision Shows the current BIOS version. Detected automatically System Time Sets the time using 24-hour format. Values set take effect immediately. System Date Sets the date using dd/mm/yy format (except English, which uses mm/dd/yy format). Language Sets the language for BIOS Setup.
319954-001.book Page 25 Thursday, February 3, 2005 3:03 PM Troubleshooting System Devices Menu Setting Description Default Video Display Device Sets whether the built-in display automatically switches to an external display, if one is detected. Auto External Pointing Device Disables the internal pointing devices when an external pointing device is connected. Auto Legacy USB Support Enables BIOS support for USB mouse, keyboard, and diskette disk drive during startup.
319954-001.book Page 26 Thursday, February 3, 2005 3:03 PM Troubleshooting Security Menu (Continued) Setting Description Default Set Administrator Password Press enter to set, change, or clear the administrator password, which protects BIOS Setup settings. The password can have no more than 8 characters (0–9, A–Z), and cannot include special or accented characters. Enter Require Password on Boot Sets whether a user password is required when the notebook boots.
319954-001.book Page 27 Thursday, February 3, 2005 3:03 PM Troubleshooting Exit Menu Setting Description Save Changes and Exit Saves Setup changes, then exits and reboots. Discard Changes and Exit Discards any Setup changes made since last save, then exits and reboots. Does not affect password, date, or time changes. Get Default Values Restores default settings, and remains in Setup. Does not affect password, date, or time changes.
319954-001.book Page 28 Thursday, February 3, 2005 3:03 PM Troubleshooting To Change Video Memory Settings Using BIOS Setup Utility The notebook comes with either 32 MB or 16 MB of video memory. your video memory to 8 MB, 16 MB, 32 MB, or ✎ Changing 64 MB may change the performance of your notebook, depending on your selection. To change your video memory: 1. Select Start > Turn Off Computer > Restart. 2. Press F2 when the splash screen appears. 3.
319954-001.book Page 29 Thursday, February 3, 2005 3:03 PM Troubleshooting Please refer to Microsoft operating system (OS) documentation and Web site for specific information regarding: ■ Repairing missing or damaged OS files ■ Adding or removing Windows components ■ Creating System Restore Points The Operating System CD may be required for these actions. However, procedures will vary.
319954-001.book Page 30 Thursday, February 3, 2005 3:03 PM Troubleshooting To restore the notebook to a previous date and time when it was functioning optimally: 1. Select Start > Help & Support > Tools > System Restore. 2. Follow the on-screen directions for restoring the notebook. Operating System (OS) CD Repair To repair the operating system without deleting your personal data, use the standard Microsoft OS CD that was shipped with the notebook.
319954-001.book Page 31 Thursday, February 3, 2005 3:03 PM Troubleshooting OS CD Reinstall If other recovery efforts do not successfully repair the notebook, you can reinstall the operating system. Å WARNING: Personal data and software you have installed on the notebook will be lost during the OS CD reinstall. To protect your data, make a backup copy of My Documents before reinstalling your operating system. Visit Help and Support to learn more about backing up your files.
319954-001.book Page 32 Thursday, February 3, 2005 3:03 PM Troubleshooting 11. Select Format the partition using the NTFS file system (Quick) and press enter. A caution is displayed that formatting this drive will delete all current files. 12. Press F to format the drive. The reinstallation process begins. This process takes 1 to 2 hours to complete. The notebook restarts in Windows after the process is complete.
319954-001.book Page 1 Thursday, February 3, 2005 3:03 PM 7 Reference Information Modem Reference Information You can customize the operation of the modem using AT commands and S-registers. You can do this from Phone and Modem Options in Control Panel, from most communications software, or by using terminal mode in your software. should have a good understanding of modems and how they ✎ You operate before you change default settings.
319954-001.book Page 2 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) Command (Conexant) A Go off-hook and attempt to answer a call. A/ Re-execute command (not preceded by AT).
319954-001.book Page 3 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) On 0=go online, 1=go online and initiate retrain sequence. P Force pulse dialing. Qn 0=enable result codes to DTE (default), 1=disable. Sn Select S-register n as default. Sn=v Set default S-register n to value v. T Force DTMF dialing. Vn Report result codes: 0=short form (terse), 1=long form (verbose) (default).
319954-001.book Page 4 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) +DS=a,b,c,d Controls V.42 bis data compression function (b, c, and d are optional): ■ ■ ■ ■ +DS44=a,b, c,d,e,f,g,h,i Controls V.44 data compression function (b, c, d, e, f, g, h, and i are optional): ■ ■ ■ ■ ■ ■ ■ ■ ■ 7–4 a sets direction(s) of data compression function, seen by DTE: 0=negotiated, no compression; 3=both directions (default).
319954-001.book Page 5 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) +ESA=a,b,c, Controls operation of synchronous access mode: d,e,f,g,h ■ ■ ■ ■ ■ ■ ■ ■ ■ a=0 specifies that in transparent sub-mode, modem transmits 8-bit SYN sequence on idle. b=0 specifies that in framed sub-mode, modem transmits HDLC flags on idle (default and fixed).
319954-001.book Page 6 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) +ILRR=n Report local port rate: 0=disable, 1=enable. +IPR=n Set data rate at which the modem accepts commands when connected: 0 (allows operation only at rates automatically detectable by modem), 2400, 4800, 9600, 19200, 38400, 57600, or 115200.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) +PSS=n 0=modems decide whether to use short startup procedures, 2=use full startup procedures on all subsequent connections. +VCID=n Set caller ID reporting: 0=disable (default), 1=enable with formatted presentation, 2=enable with unformatted presentation. +VRID=n Report caller ID: 0=use formatted presentation, 1=use unformatted presentation.
319954-001.book Page 8 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) &T0 Terminate any test in progress. &T1 Initiate local analog loopback. &V Display current configuration and stored profiles. %TTn PTT testing of signal level: 00–09=DTMF dial 0–9, 0A=DTMF *, 0B=DTMF #, 0C=DTMF A, 0D=DTMF B, 0E=DTMF C, 0F=DTMF D, 10=V.21 Channel 1mark symbol, 11=V.21 Channel 2mark symbol, 12=V.23 Channel 1mark symbol, 13=V.
319954-001.book Page 9 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AT Commands (Advanced Users Only) (Continued) Command (Conexant) +MR=0 Disable reporting of modulation connection. +MR=1 Enable reporting of modulation connection (+MCR: and +MRR: are transmitted) (default). +MR=2 Enable reporting of modulation connection (+MCR: and Receive Rate Only: are transmitted). +MS=a,b,c, Select modulation (b, c, d, e, and f are optional).
319954-001.book Page 10 Thursday, February 3, 2005 3:03 PM Reference Information ECC Commands (Continued) Command (Conexant) +ER: a Select error control protocol: NONE=error control not in use, LAPM=V.42 LAPM protocol, ALT=MNP. +ER=n Error control reporting: 0=disable, 1=enable. +ES=a,b,c Select error control and synchronous mode (b and c are optional). ■ a is requested mode when modem is originator: 0=initiate call with direct mode, 1=initiate call with normal mode, 2=initiate V.
319954-001.book Page 11 Thursday, February 3, 2005 3:03 PM Reference Information FAX Class 1 Command (Conexant) +FAE=n Data/fax auto answer: 0=disable (default), 1=enable. +FAR=n 0=disable adaptive reception (default), 1=enable. +FCL=n Set loss-of-carrier delay in units of 100 ms (n=0 to 255). +FCLASS=n Set active service class: 0=data mode (default), 1=Fax Class 1, 1.0=Fax Class 1.0 mode, 8=voice mode.
319954-001.book Page 12 Thursday, February 3, 2005 3:03 PM Reference Information Voice Commands Command (Conexant) +FCLASS=8 Select voice mode. +VDR=a,b Set report ring cadence and timing of RING event code: ■ ■ +VDT=a,b a=0 disables ring cadence reporting, a=1 enables. b sets report content: 0=DROF and DRON messages only. Set report control tone cadence: ■ ■ a=0 disables ring cadence reporting, a=1 enables. b=0 reports CPOF and CPON messages only.
319954-001.book Page 13 Thursday, February 3, 2005 3:03 PM Reference Information Voice Commands (Continued) Command (Conexant) +VSP=a Disable (a=0) or enable (a=1) speakerphone. +VTD=n Set beep duration (1 to 500 × 0.01 sec). +VTR Start voice transmission and reception. +VTS=string Send voice tones. +VTX Start voice transmission. AT* Commands Command (Conexant) *B Display black-listed numbers. *D Display delayed numbers.
319954-001.book Page 14 Thursday, February 3, 2005 3:03 PM Reference Information S-Registers (Conexant) Register Function (Conexant) Range/Units Default S0 Number of rings to auto-answer. 0-255/rings 0 S1 Ring counter. 0-255/rings 0 S2 Escape character. 0-255/ASCII 43 S3 Line termination character. 0-127/ASCII 13 S4 Response formatting character. 0-127/ASCII 10 (line feed) S5 Command line editing character. 0-32/ASCII 8 (backspace) S6 Wait time for dial tone.
319954-001.
319954-001.book Page 16 Thursday, February 3, 2005 3:03 PM Reference Information Safety Information Power Cords The power cord supplied with the notebook AC adapter should match the plug and voltage requirements for your local area. Regulatory approval for the AC adapter has been obtained using the power cord for the local area. However, if you travel to a different area or need to connect to a different outlet or voltage, you should use one of the power cords listed below.
319954-001.book Page 17 Thursday, February 3, 2005 3:03 PM Reference Information Battery Safety ■ To avoid risk of fire, burns, or damage to your battery pack, do not allow a metal object to touch the battery contacts. ■ Do not disassemble the battery pack. There are no serviceable parts inside. Do not dispose of the battery pack in fire or water. ■ Handle a damaged or leaking battery pack with extreme care. If you come in contact with the electrolyte, wash the exposed skin with soap and water.
319954-001.book Page 18 Thursday, February 3, 2005 3:03 PM Reference Information Laser Safety The CD-ROM and DVD drives used with the notebook are certified as a Class 1 laser devices according to the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard and International Standards IEC 825/IEC 825-1 (EN60825/EN60825-1).
319954-001.book Page 19 Thursday, February 3, 2005 3:03 PM Reference Information ■ Avoid direct eye exposure to the infrared LED beam. Be aware that the beam is invisible light and cannot be seen. ■ Do not attempt to view the infrared LED beam with any type of optical device. Mercury Safety This product contains mercury in the fluorescent lamp of the liquid-crystal display, and may require special handling at end of life.
319954-001.book Page 20 Thursday, February 3, 2005 3:03 PM Reference Information Wireless Notice In some environments, the use of wireless devices may be restricted. Such restrictions may apply aboard airplanes, in hospitals, near explosives, in hazardous locations, etc. If you are uncertain of the policy that applies to the use of this device, please ask for authorization to use it prior to turning it on.
319954-001.book Page 21 Thursday, February 3, 2005 3:03 PM Reference Information For more information, consult your dealer, an experienced radio/television technician, or the following booklet, prepared by the Federal Communications Commission: How to Identify and Resolve Radio-TV Interference Problems. This booklet is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4. At the first printing of this manual, the telephone number was (202) 512-1800.
319954-001.book Page 22 Thursday, February 3, 2005 3:03 PM Reference Information The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service. If trouble is experienced with this equipment, call 1-800-652-6672.
319954-001.book Page 23 Thursday, February 3, 2005 3:03 PM Reference Information Declaration of Conformity (U.S.A.) Responsible Party: Hewlett-Packard Company Manager of Corporate Product Regulations 3000 Hanover Street Palo Alto, CA 94304 +1 (650) 857-1501 declares that the product(s) Trade name: Regulatory Model Number: Hewlett-Packard Company CRVSA-02T1-75 CRVSA-02T1-90 Complies with Part 15 of the FCC Rules. Operation is subject to the following 2 conditions: 1.
319954-001.book Page 24 Thursday, February 3, 2005 3:03 PM Reference Information Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. Le composant RF interne est conforme à la norme CNR-210 d'Industrie Canada.
319954-001.book Page 25 Thursday, February 3, 2005 3:03 PM Reference Information ■ EN 60950 (IEC 60950)—Product Safety ■ EN 300 328-2 Technical requirements for 2.4-GHz radio equipment (WLAN) ■ EN 301 489-1 and -17 General EMC requirements for radio equipment (WLAN) The IEEE 802.
319954-001.book Page 26 Thursday, February 3, 2005 3:03 PM Reference Information Cet équipement a été reconnu conforme aux décisions du Conseil 99/5/EC relatives à la connexion pan-européenne de terminal simple au réseau téléphonique public commuté (RTPC) et à un réseau sans fil RF.
319954-001.
319954-001.book Page 28 Thursday, February 3, 2005 3:03 PM Reference Information TELEC approval number: D02-0005JP Name of Equipment: T60H424 2.
319954-001.book Page 29 Thursday, February 3, 2005 3:03 PM Reference Information New Zealand Conexant AMC20493-KT5 Data Fax Modem PTC 211/02/071 PTC200 General Warning The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty.
319954-001.book Page 30 Thursday, February 3, 2005 3:03 PM Reference Information Conexant AMC20493-KT5 Data Fax Modem PTC 211/02/071 (Continued) PTC200 7.5.2 (3) (4) Ringer Sensitivity This device may be subject to ringing or bell tinkle when certain other devices are connected to the same line. If this occurs, the problem should not be referred to the Telecom Faults Service.
319954-001.book Page 31 Thursday, February 3, 2005 3:03 PM Reference Information Russia Brazil Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. International Products sold internationally by the manufacturer and its authorized dealers meet the specifications listed on the following page.
319954-001.book Page 32 Thursday, February 3, 2005 3:03 PM Reference Information Manufacturer’s Name: Manufacturer’s Address: Hewlett-Packard Company, Personal Systems Group 19310 Pruneridge Ave., Cupertino, CA 95014, U.S.A. declares that the following product Product Name: Regulatory Model Number: Product Options: Compaq Notebook Series CRVSA-02T1-75 CRVSA-02T1-90 Includes all options for analog modems (Conexant) and 802.
319954-001.book Page 33 Thursday, February 3, 2005 3:03 PM Reference Information Radio: Equipment Class 2 EN 301 489-17: 2000 Specific conditions for wideband data HYPERLAN equipment EN 300 328-2: 2000 Technical requirements for Radio equipment Notified Body Number: 0682 Notified Body Address: CETECOM ICT Services GmbH, Untertuerkheimer Str.
319954-001.
319954-001.
319954-001.
319954-001.
319954-001.
319954-001.
319954-001.book Page 7 Thursday, February 3, 2005 3:03 PM Index serial 6–18 startup 6–19 USB 6–19 wireless 6–21 turning off notebook 2–2 wireless network connection 4–11 turning on notebook 1–13, 2–2 wireless network connection 4–11 U U.S.A.