Specifications

ManualsBrandsCompaq ManualsComputer equipmentArmada 7792

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Notice

The information in this guide is subject to change without notice.

COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR

TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;

NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM

THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.

This guide contains information protected by copyright. No part of this guide may be

photocopied or reproduced in any form without prior written consent from Compaq

Computer Corporation.



1997 Compaq Computer Corporation.

Compaq and LTE are registered in the U. S. Patent and Trademark Office.

Armada is a trademark of Compaq Computer Corporation.

Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corporation.

The software described in this guide is furnished under a license agreement or

nondisclosure agreement. The software may be used or copied only in accordance with

the terms of the agreement.

Product names mentioned herein may be trademarks and/or registered trademarks of their

respective companies.

Maintenance and Service Guide

Compaq

ArmadaStation

Compaq

Armada MiniStation E

Compaq

Armada MiniStation EX

Compaq Armada 7000 Family of Personal Computers

First Edition August 1997

Documentation Part Number 272412-001

Spare Part Number 296391-001

Compaq Computer Corporation

Summary of content (147 pages)

PAGE 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notice The information in this guide is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. This guide contains information protected by copyright.
PAGE 2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents Preface Symbols..............................................................................................................ix Technician Notes ...............................................................................................ix Serial Number ..................................................................................................... x Locating Additional Information....................................
PAGE 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9 Miscellaneous Enclosures Kit Components...........................................3-12 3.10 Miscellaneous Plastics Kit Components ..............................................3-13 3.11 MultiBay/PC Card Assembly ...............................................................3-14 3.12 ArmadaStation and Armada MiniStation Options ...............................3-16 3.13 Miscellaneous .................................................
PAGE 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.14 5.15 5.16 5.17 5.18 Expansion Boards .................................................................................5-50 Mechanism Assembly...........................................................................5-52 Power Supply........................................................................................5-55 Backplane Assembly.............................................................................
PAGE 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface This Maintenance and Service Guide is a troubleshooting guide that can be used for reference when servicing the Compaq ArmadaStation and Armada MiniStation E and EX. Compaq Computer Corporation reserves the right to make changes to the Compaq ArmadaStation and Armada MiniStation E and EX without notice. Additional information is available on the Compaq ArmadaStation and Armada MiniStation E and EX Illustrated Parts Map.
PAGE 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Number When requesting information or ordering spare parts, provide the ArmadaStation or Armada MiniStation serial number. The ArmadaStation serial number is located on the right side below the PCI/ISA expansion slots; the Armada MiniStation serial number is located on the left side above the power button.
PAGE 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 1 Product Description 1.1 ArmadaStation Features The Compaq ArmadaStation provides fully integrated desktop capabilities for the Compaq Armada 7000 Family of Personal Computers. The ArmadaStation eliminates the need to disconnect external devices when you remove the computer. Figure 1-1.
PAGE 8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The ArmadaStation provides a MultiBay device bay, a half-height device bay, two PC Card slots, integrated Ethernet, integrated stereo speakers, modem connections, computer I/O port replication, and connections for up to two PCI or ISA expansion boards.
PAGE 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The ArmadaStation also provides a variety of external equipment connectors.
PAGE 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 ArmadaStation Components The external components on the top, front, and right side of the ArmadaStation are shown in Figure 1-2 and described in Table 1-1. Figure 1-2.
PAGE 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional components on the front and right sides of the ArmadaStation are shown in Figure 1-3 and described in Table 1-2. Figure 1-3.
PAGE 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The components on the rear panel and left side of the ArmadaStation are shown in Figure 1-4 and described in Table 1-3. Figure 1-4.
PAGE 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The external connectors on the right side and rear panel of the ArmadaStation are shown in Figure 1-5 and described in Table 1-4. Figure 1-5.
PAGE 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activity Lights The ArmadaStation has two activity lights. MultiBay Activity Light The MultiBay activity light is located on the MultiBay. This light turns on when information from a removable drive inserted in the ArmadaStation MultiBay is accessed. Power/Suspend Light The power/suspend light is located on the front/right corner of the ArmadaStation and is visible from both the front and right side of the ArmadaStation.
PAGE 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security Lock The ArmadaStation features a security lock that allows all computer and ArmadaStation resources (hard drives, diskette drives, CD-ROM drives, PC Cards) to be secured to the system (computer and ArmadaStation). When the security lock is engaged, the computer cannot be undocked, and no drives or PC Cards can be removed from the system.
PAGE 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Regional Modem and Ethernet Differences The modem and Ethernet connectors found on the ArmadaStation vary by region.
PAGE 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3 Armada MiniStation Features The Compaq Armada MiniStation provides fully integrated desktop capabilities for the Compaq Armada 7000 Family of Personal Computers. The Armada MiniStation eliminates the need to disconnect external devices when you undock the computer from the Armada MiniStation. Figure 1-6. Compaq Armada MiniStation The Armada MiniStation is available in two models to provide expanded functionality.
PAGE 18
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4 Armada MiniStation Components The external components on the top and right side of the Armada MiniStation are shown in Figure 1-7 and described in Table 1-7. NOTE: The Armada MiniStation E does not contain a battery charging bay or MultiBay. Figure 1-7.
PAGE 20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The components on the left side of the Armada MiniStation are shown in Figure 1-8 and described in Table 1-8. Figure 1-8.
PAGE 21
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The external components and connectors on the rear panel of the Armada MiniStation are shown in Figure 1-9 and described in Table 1-9. Figure 1-9.
PAGE 22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activity Lights The ArmadaStation MiniStation EX has two activity lights. MultiBay Light The MultiBay light is located on the left side of the Armada MiniStation EX and is visible from both the top and left sides of the Armada MiniStation EX. This light turns on when information from a removable drive inserted in the MultiBay is accessed.
PAGE 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PC Card Slots The ArmadaStation MiniStation EX has two PC Card slots. The slots support one of the following PC Card combinations: ■ Two Type I or Type II PC Cards ■ One Type III PC Card in the top slot and a Type I or Type II in the bottom slot. If a Type III PC Card is inserted in the bottom PC Card slot, no other PC Cards can be used. The PC Card slot supports both 5-volt and 3.
PAGE 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 2 Troubleshooting This chapter contains troubleshooting information for the ArmadaStation and Armada MiniStation. Information on how to identify and correct some common hardware, memory, and software problems is included.
PAGE 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solving Docking and Undocking Problems The following table lists some common docking problems and recommended actions to take when they occur. Table 2-1 Solving Docking and Undocking Problems Problem Probable Cause Recommended Action(s) Cannot undock computer. The computer is using Windows NT and a software application is running. Exit all applications and turn off the system if you are using Windows NT.
PAGE 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solving Expansion Board Problems The following table lists some common expansion board problems and recommended actions to take when they occur. Table 2-2 Solving Expansion Board Problems Problem Probable Cause Recommended Action(s) Expansion board does not work. Expansion board is not properly seated. Reinstall the expansion board. Expansion board is not recognized by the system.
PAGE 27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 2-3 Solving Ethernet Network Problems Problem Probable Cause Recommended Action(s) When turned on, the computer does not detect the network. The computer is not connected to the Ethernet network. Connect the computer to the Ethernet network. Suspend or Hibernation was initiated. Exit Suspend or Hibernation. Windows 95: Restart the system by clicking Start > Shut Down > Restart the Computer.
PAGE 28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table 2-3 Continued Problem Probable Cause The computer stopped communicating with the network after exiting Suspend. The computer does not detect Windows 95: Restart the system by clicking network drivers. Start > Shut Down > Restart the Computer. Windows NT: Click Start > Shut Down. Power the computer back on. The computer stopped communicating with the network for no apparent reason.
PAGE 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers for the Compaq ArmadaStation and Armada MiniStation.
PAGE 31
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 ArmadaStation Components Figure 3-1.
PAGE 32
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Miscellaneous Base Plastics Kit Components Figure 3-2.
PAGE 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Miscellaneous Base Hardware Kit Components Figure 3-3.
PAGE 35
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Miscellaneous Cable Kits Figure 3-4.
PAGE 36
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 Miscellaneous Cable Kit Components Figure 3-5.
PAGE 38
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 Miscellaneous Table 3-8 Spare Parts: Miscellaneous (not illustrated) Description Spare Part Number ArmadaStation Miscellaneous Base Screw Kit 272131-001 Tool kit, includes: case utility tool connector removal tool loop back plugs 100767-001 3.
PAGE 39
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 Armada MiniStation Components Figure 3-6.
PAGE 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 41
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9 Miscellaneous Enclosures Kit Components Figure 3-7.
PAGE 42
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10 Miscellaneous Plastics Kit Components Figure 3-8.
PAGE 43
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11 MultiBay/PC Card Assembly Figure 3-9.
PAGE 44
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 45
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12 ArmadaStation and Armada MiniStation Options Figure 3-10.
PAGE 46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 47
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13 Miscellaneous Table 3-15 Spare Parts: Miscellaneous (not illustrated) Description Spare Part Number Armada MiniStation Miscellaneous Screw Kit 272138-001 Tool kit, includes: case utility tool connector removal tool loop back plugs 100767-001 3.
PAGE 48
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 4 Removal and Replacement Preliminaries This chapter provides general service information for the Compaq ArmadaStation and Armada MiniStation. Adherence to the procedures and precautions described in this chapter is essential for proper service. 4.1 Electrostatic Discharge A sudden discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
PAGE 49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preventing Electrostatic Damage to Equipment Many electronic components are sensitive to ESD. Circuitry design and structure determine the degree of sensitivity. The following proper packaging and ground precautions are necessary to prevent damage. ■ Protect all electrostatic sensitive parts and assemblies with nonconductive or approved containers or packaging.
PAGE 50
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grounding Methods The method for grounding must include either a wrist strap or a foot strap at a grounded workstation. When seated, wear a wrist strap connected to a grounded system. When standing, use footstraps and a grounded floor mat.
PAGE 51
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grounding Equipment Use the following equipment to prevent static electricity damage to equipment: Wrist Straps are flexible straps with a minimum of one megohm +/- 10% resistance in the ground cords. To provide proper ground, a strap must be worn snug against the skin. On grounded mats without banana-plug connectors, connect a wrist strap with alligator clips.
PAGE 52
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Service Considerations Listed below are some of the considerations that you should keep in mind during the disassembly and assembly of the ArmadaStation or Armada MiniStation.
PAGE 53
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cables and Connectors Cables must be handled with extreme care to avoid damage. Apply only the tension required to seat or unseat the cables during insertion or removal from the connector. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing the cables, and ensure that the cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced.
PAGE 54
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 5 ArmadaStation Removal and Replacement Procedures This chapter presents the removal and replacement procedures for the ArmadaStation. 5.1 Serial Number The ArmadaStation serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is displayed on the right side of the ArmadaStation, below the expansion slot connectors (Figure 5-1). Figure 5-1.
PAGE 55
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Disassembly Sequence Chart Use the chart below to determine the section number and disassembly sequence for removing components from the ArmadaStation. 5.3 Preparing the ArmadaStation for Disassembly 5.4 External Components Compaq Logo ArmadaStation Feet Alignment Tray Assembly 5.5 Rear Panel Assembly 5.6 Upper Case Assembly 5.7 Drive Cage Shield 5.8 Half-Height Bays Half-Height Drives Half-Height MultiBay Adapters 5.
PAGE 56
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.3 Preparing the ArmadaStation for Disassembly Before beginning removal and replacement procedures, follow these steps: 1. Turn the ArmadaStation keylock clockwise to unlock it. 2. Undock the computer from the ArmadaStation. 3. Turn off the ArmadaStation. 4. Disconnect the power cord from the wall outlet 1 (Figure 5-3). 5. Disconnect the power cord from the ArmadaStation 2. Figure 5-3. Disconnecting the ArmadaStation 6.
PAGE 57
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 External Components This section describes the removal and replacement procedures that do not require access to the internal components of the ArmadaStation. This includes: ■ Compaq logo ■ Feet ■ Alignment tray assembly Compaq Logo You need to install a Compaq logo on the ArmadaStation or monitor support cover only if the old logo is damaged or removed. The logo is an adhesive-backed label.
PAGE 58
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ArmadaStation Feet The feet for the ArmadaStation are rectangular, adhesive-backed rubber pads. Install the feet by removing the protective covering from the adhesive back and placing the feet in their positions on the bottom of the ArmadaStation (Figure 5-5). Figure 5-5.
PAGE 59
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Alignment Tray Assembly The alignment tray assembly is used to align the computer on the ArmadaStation. The left side of the computer should be aligned with the left side of the alignment tray assembly when docking the computer. To remove the alignment tray assembly from the ArmadaStation, pull forward on the docking restraint latch (Figure 5-6). Figure 5-6.
PAGE 60
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the alignment tray assembly, follow these steps: 1. Place the alignment tray assembly on the upper case assembly. 2. Align the tabs in the back of the alignment tray assembly with the slots in the upper case assembly (Figure 5-7). 3. Push the alignment tray assembly into place on the upper case assembly. Figure 5-7.
PAGE 61
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 Rear Panel Assembly The rear panel assembly is spared as a unit and consists of the: ■ Rear panel ■ Rear panel shield ■ Rear panel release latch To remove the rear panel assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Position the ArmadaStation so the rear panel is facing forward. 3. Slide the rear panel release latch to the left 1 (Figure 5-8). 4.
PAGE 62
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NOTE: Once the rear panel assembly has been removed, the manual release lever is accessible (Figure 5-9). When this lever is moved to the right, the mechanism assembly, which secures the computer when it is docked in the ArmadaStation, releases and allows the computer to be manually undocked. Figure 5-9.
PAGE 63
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Before installing the rear panel assembly, make sure the manual release lever is positioned as far to the left as it will go. To install the rear panel assembly, follow these steps: 1. Slide the rear panel release latch to the left. 2. Align the tabs on the top edge of the rear panel assembly with the slots on the back edge of the upper case assembly (Figure 5-10). Figure 5-10. Installing the Rear Panel Assembly 3.
PAGE 64
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6 Upper Case Assembly The upper case assembly is spared as a unit and consists of the: ■ Top cover ■ PC Card door ■ Speaker grills ■ Monitor support cover slot buttons ■ Label To remove the upper case assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Position the ArmadaStation so the front is facing forward. 3. Remove the alignment tray assembly (Section 5.4). 4.
PAGE 65
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. Grasp the back of the upper case assembly, lift up on the back of the assembly, and swing it forward (Figure 5-12). Figure 5-12. Removing the Upper Case Assembly 7. Set aside the upper case assembly.
PAGE 66
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the upper case assembly, follow these steps. 1. Align the front edge of the upper case assembly with the front edge of the base assembly 1 (Figure 5-13). 2. Swing the back of the upper case assembly back and down until it rests on the base assembly 2 . Figure 5-13. Installing the Upper Case Assembly 3. Replace the three upper case screws.
PAGE 67
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7 Drive Cage Shield The drive cage shield is located in the base assembly and covers the half-height bay assemblies. To remove the drive cage shield, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5). 4. Remove the upper case assembly (Section 5.6). 5.
PAGE 68
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the drive cage shield, follow these steps: 1. Align the tabs on the back of the shield (Figure 5-15). 1 with the slots in the backplane assembly NOTE: Make sure any cables used to connect half-height drive assemblies are properly tucked underneath the slots in the backplane cover and not resting on top of the drive cages before installing the drive cage shield. 2. Swing the front of the shield down 2. 3.
PAGE 69
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8 Half-Height Bays The ArmadaStation features one standard half-height bay, which is located on the front of the ArmadaStation. This bay supports any standard half-height drive (such as a diskette or hard drive) or a MultiBay (using a half-height MultiBay adapter). A MultiBay comes as standard equipment in the ArmadaStation right half-height bay. This allows you to use removable drives from the computer or charge battery packs.
PAGE 70
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Remove the half-height bay blank bezel cover from the drive cage (Figure 5-16). Figure 5-16.
PAGE 71
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4. Remove the screws from the sides of the half-height drive (Figure 5-17). NOTE: The half-height drive should have two screws installed in each side. If these screws are missing, appropriate-sized screws must be obtained to secure the half-height drive to the drive cage shield. Figure 5-17.
PAGE 72
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Place the drive cage over the half-height drive. Align the front of the drive with the tab on the front of the drive cage (Figure 5-18). NOTE: The drive cage should be aligned so the “L” and “LEFT” indicators can be read when the half-height drive is installed in the ArmadaStation left half-height bay. Figure 5-18.
PAGE 73
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. Install the screws securing the half-height drive to the drive cage (Figure 5-19). Figure 5-19.
PAGE 74
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Insert the half-height drive assembly in the base assembly, making sure to align the alignment holes on the drive cage with the alignment pins in the base assembly (Figure 5-20). Figure 5-20. Installing a Half-Height Drive 8. Attach the appropriate cable to the connectors on the half-height drive and the ArmadaStation.
PAGE 75
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Half-Height MultiBay Adapters To remove a half-height MultiBay adapter, complete these steps: 1. Remove the drive cage shield (Section 5.7). 2. Disconnect the hard drive, CD-ROM/audio, diskette drive, and MultiBay cables from the half-height MultiBay adapter. 3. Lifting the left side first, lift the adapter out of the base assembly until the security extension bar on the right side is clear (Figure 5-21). Figure 5-21.
PAGE 76
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Remove the half-height bay blank bezel cover from the drive cage. 4. Remove the screws from the sides of the half-height MultiBay adapter (Figure 5-22). Figure 5-22.
PAGE 77
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Place the drive cage over the half-height MultiBay adapter. Align the front of the adapter with the tab on the front of the drive cage (Figure 5-23). Figure 5-23.
PAGE 78
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. Install the screws securing the half-height MultiBay adapter to the drive cage (Figure 5-24). Figure 5-24.
PAGE 79
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Turn the drive cage/half-height MultiBay adapter assembly upside down. Position the security extension bar 1 as far to the left as it will go. This is done by pressing the tabs 2 on the lock slide and moving the security extension bar to the left until it locks on the first tab 3 (Figure 5-25).
PAGE 80
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9. Swing the drive cage/half-height MultiBay adapter assembly into the base assembly from left to right. Make sure the security extension bar 1 extends to the right. If an Armada 7000 Half-Height MultiBay Adapter is being installed in the left half-height bay, the bar must fit into the channel 2 on the MultiBay installed in the right half-half bay.
PAGE 81
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10. Connect the diskette drive cable to the diskette drive connector on the half-height MultiBay adapter (Figure 5-27). Figure 5-27.
PAGE 82
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11. Connect the hard drive cable to its respective connectors on the half-height MultiBay adapter and backplane assembly (Figure 5-28). Figure 5-28.
PAGE 83
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. Connect the MultiBay cable to the half-height MultiBay adapter (Figure 5-29). CAUTION: Be careful when connecting the MultiBay cable to the half-height MultiBay adapter. The connectors can only connect one way. Attempts to connect the cable the wrong way can result in damage to the connectors on the cable and the half-height MultiBay adapter.
PAGE 84
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. Connect the CD-ROM/audio cable to its respective connectors on the half-height MultiBay adapter and backplane assembly (Figure 5-30). Figure 5-30. Connecting the CD-ROM/Audio Cable to the Armada 7000 Half-Height MultiBay Adapter and Backplane Assembly 5.9 I/O Assembly The I/O assembly consists of the I/O board, connector board, PC Card assembly, and I/O panel.
PAGE 85
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Remove the two screws 1 securing the I/O assembly to the top brace (Figure 5-31). 4. Grasp the outside edges of the I/O assembly and pull the assembly until it disconnects 2 . CAUTION: Be careful when removing the I/O assembly. The assembly includes a multiple-pin connector that is firmly connected to the backplane assembly. Pull firmly to disconnect the I/O assembly from the backplane assembly. Figure 5-31.
PAGE 86
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the 100BaseTX Ethernet module, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the rear panel assembly (Section 5.5). 3. Remove the I/O assembly (Section 5.9). 4. Remove the four jumpers from the I/O assembly 1 (Figure 5-32). 5. Connect the 100BaseTX Ethernet module to the connectors on the right side of the I/O assembly 2 . Figure 5-32.
PAGE 87
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the I/O assembly, follow these steps: 1. Align the right side of the I/O bracket with the groove in the expansion card cage (Figure 5-33). 2. Slide the I/O assembly into the ArmadaStation itself on the backplane assembly. 1 until the assembly connector seats NOTE: Make sure the manual release lever does not interfere with the installation of the I/O bracket. 3.
PAGE 88
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.10 Top Brace The top brace separates the power supply, I/O assembly, mechanism assembly, and backplane assembly from the upper case assembly. The top brace must be removed to access the power supply, mechanism assembly, and backplane assembly. To remove the top brace, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3.
PAGE 89
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Lift up on the rear edge of the top brace and swing the brace forward until it clears the ArmadaStation (Figure 5-35). Figure 5-35.
PAGE 90
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the top brace, follow these steps: 1. Align the tabs on the front of the top brace backplane assembly (Figure 5-36). 1 with the slots on the top of the 2. Swing down the back edge of the top brace until the brace is resting on the base assembly and power supply 2 . Figure 5-36. Installing the Top Brace 3. Install the two screws securing the top brace to the base assembly and power supply.
PAGE 91
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11 Left Speaker Assembly The left speaker assembly consists of the left speaker, its cover, and its insulator. To remove the left speaker assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5). 4. Remove the upper case assembly (Section 5.6). 5. Remove the drive cage shield (Section 5.7). 6.
PAGE 92
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.12 Control Panel Cable The control panel cable connects the control panel to the backplane connector and is spared as a unit. To remove the control panel cable, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5). 4. Remove the upper case assembly (Section 5.6). 5. Remove the top brace (Section 5.10). 6.
PAGE 93
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Untuck the control panel cable from the backplane assembly. 8. Remove the control panel assembly (Section 5.13). The control panel cable can be disconnected from the control panel assembly when the assembly is removed from the base assembly. NOTE: Be careful not to damage the control panel cable on the drive cage shield when removing the control panel assembly. Refer to Section 5.
PAGE 94
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Remove the three screws (Figure 5-39). 1 securing the control panel assembly to the base assembly 8. Lift the control panel assembly and control panel cable 2 from the base assembly. Figure 5-39.
PAGE 95
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9. Disconnect the control panel cable from the control panel assembly (Figure 5-40). Figure 5-40.
PAGE 96
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . After the control panel assembly has been removed, inspect the control panel spacer to determine if it should be replaced. To replace the control panel spacer, follow these steps: 1. Completely remove the old control panel spacer from the base assembly (Figure 5-41). 2. Remove the backing from the new control panel spacer and install it in the base assembly in the indicated position.
PAGE 97
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the control panel assembly, follow these steps: 1. Connect the control panel cable to the connector on the control panel assembly. 2. Rotate the security actuator clockwise 1 and push it toward the control panel assembly until it locks on the indicated position 2 (Figure 5-42). Figure 5-42.
PAGE 98
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Bend the control panel ground cable up and over the top surface of the control panel housing. 4. Insert the control panel assembly into the base assembly, making sure the pin on which the actuator spring sits 1 fits into the alignment hole in the base assembly (Figure 5-43). 2 NOTE: Be careful not to trip the security actuator during the control panel assembly installation. Figure 5-43.
PAGE 99
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Use a flat-blade screwdriver 1 to trip the C/U actuator pushing down on the actuator tab (Figure 5-44). 2 into the proper position by Figure 5-44. Tripping the C/U Actuator 6. Install the screws securing the control panel assembly to the base assembly.
PAGE 100
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Route the control panel cable between the control panel and the base assemblies 1 and around the backplane assembly 2 (Figure 5-45). Make sure the protective wrapping on the control panel cable protects the cable from the base assembly and backplane assembly sheet metal 3 . The cable end with three pieces of protective wrapping should be connected to the backplane assembly. Figure 5-45.
PAGE 101
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NOTE: When routing the control panel cable around the backplane assembly, inspect the subpan side shield and backplane-brace spacer to determine if they should be replaced. To replace these components, follow these steps: 1. Completely remove the old subpan side shield and backplane-brace spacer from the backplane and base assemblies. 2.
PAGE 102
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NOTE: The C/U actuator assembly should not be disassembled during removal and installation of the control panel assembly. However, if it should be removed, refer to Figure 5-47 for the proper position of the security actuator 1 , torsion spring 2 , and MultiBay security arm 3 . Figure 5-47.
PAGE 103
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.14 Expansion Boards The ArmadaStation provides two slots for 32- or 64-bit PCI expansion boards and two slots for 16-bit, full-length ISA expansion boards. Any combination of two of these boards can be installed in the ArmadaStation. For additional information, consult the documentation included with the expansion boards.
PAGE 104
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Select the slot into which the expansion board is to be inserted: PCI expansion boards are installed in the shorter slots 1 ; ISA expansion boards are installed in the longer slots 2 (Figure 5-49). Figure 5-49. Expansion Board Slots 6. Align the bracket on the left side of the expansion board with the expansion slot on the left side of the ArmadaStation. 7.
PAGE 105
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.15 Mechanism Assembly The mechanism assembly provides the motorized docking feature of the ArmadaStation. IMPORTANT: The mechanism assembly contains white lithium grease, which is used as a lubricant. The assembly is spared as a unit and should not be disassembled. To remove the mechanism assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3.
PAGE 106
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. Disconnect the two mechanism assembly cables from the backplane assembly (Figure 5-51). Figure 5-51.
PAGE 107
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9. Remove the mechanism assembly by pressing down on the two square tabs on the mechanism assembly cover 1 and pulling the assembly out of the backplane assembly 2 (Figure 5-52). Figure 5-52. Removing the Mechanism Assembly Reverse the removal procedure described above to install the mechanism assembly.
PAGE 108
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.16 Power Supply The power supply is located in the left rear corner of the ArmadaStation. It is replaced as an assembly with its fan. To remove the power supply, follow these steps: CAUTION: Do not handle or carry the power supply by the wiring harness. This can cause damage to the power supply and wiring harness. 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3.
PAGE 109
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7. Remove the two screws 1 securing the power supply to the backplane assembly and base assembly (Figure 5-53). 8. Disconnect the two cables attaching the power supply to the backplane assembly 2. CAUTION: Make sure the power supply cables are properly unclipped from the backplane assembly before disconnecting the power supply cables. 9. Remove the power supply from the base assembly 3. Figure 5-53.
PAGE 110
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.17 Backplane Assembly The backplane assembly consists of the backplane board, backplane brace, docking connector, alignment pins, and the backplane shield. The backplane assembly is spared as a unit. To remove the backplane assembly, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.5). 4.
PAGE 111
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15. Remove the two screws securing the backplane assembly to the base assembly (Figure 5-54). 1 16. Grasp the top of the backplane assembly and lift up on the assembly and remove it from the base assembly 2 . NOTE: When removing the backplane assembly, do not use the heatsink assembly. 3 to lift the Figure 5-54. Removing the Backplane Assembly Reverse the removal procedure described above to install the backplane assembly.
PAGE 112
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.18 Expansion Card Cage The expansion card cage separates the expansion cards and I/O assembly from the power supply and mechanism assembly. It also provides structural support for the mechanism assembly and power supply. To remove the expansion card cage, follow these steps: 1. Prepare the ArmadaStation for disassembly (Section 5.3). 2. Remove the alignment tray assembly (Section 5.4). 3. Remove the rear panel assembly (Section 5.
PAGE 113
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12. Flex the right bottom side of the expansion card cage away from the retainer on the base assembly 1 and swing the cage up and away 2 (Figure 5-55). Figure 5-55.
PAGE 114
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13. Swing the expansion card cage to the right until the tabs on the right side of the cage clear the slots in the base assembly (Figure 5-56). Figure 5-56. Removing the Expansion Card Cage Reverse the removal procedure described above to install the backplane assembly.
PAGE 115
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 6 Armada MiniStation Removal and Replacement Procedures This chapter presents the removal and replacement procedures for the Armada MiniStation. NOTE: This chapter contains instructions that refer to the Armada MiniStation in its two optional models: the Armada MiniStation E (Ethernet capability) and the Armada MiniStation EX (Ethernet, MultiBay, battery charging bay, and PC Card capabilities).
PAGE 116
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Disassembly Sequence Chart Use the chart below to determine the section number and disassembly sequence for removing components from the Armada MiniStation. 6.3 Preparing the Armada MiniStation for Disassembly 6.4 External Components Compaq Logo Armada MiniStation Feet 6.5 Enclosure Cover 6.6 Module Assembly 6.7 Power Supply 6.8 MultiBay/PC Card Assembly Figure 6-2.
PAGE 117
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Preparing the Armada MiniStation for Disassembly Before beginning removal and replacement procedures, follow these steps: 1. Turn the Armada MiniStation EX keylock counterclockwise to unlock it. 2. Undock the computer from the Armada MiniStation. 3. Disconnect the power cord from the wall outlet 1 (Figure 6-3). 4. Disconnect the power cord from the Armada MiniStation 2. Figure 6-3. Disconnecting the Armada MiniStation 5.
PAGE 118
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 External Components This section describes the removal and replacement procedures that do not require access to the internal components of the Armada MiniStation. This includes: ■ Compaq logo ■ Feet Compaq Logo A Compaq logo should be installed on the Armada MiniStation or monitor support cover only if the old logo is damaged or removed. The logo is an adhesive-backed label.
PAGE 119
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Armada MiniStation Feet The feet for the Armada MiniStation are round, adhesive-backed rubber pads. Install the feet by removing the protective covering from the adhesive back and placing the feet in their positions on the bottom of the Armada MiniStation (Figure 6-5). Figure 6-5.
PAGE 120
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 Enclosure Cover The enclosure cover is spared as a unit. To remove the enclosure cover, follow these steps: 1. Prepare the Armada MiniStation for disassembly (Section 6.3). 2. Position the Armada MiniStation so the rear panel faces forward. 3. Remove the two screws securing the enclosure cover to the module assembly (Figure 6-6). 1 4.
PAGE 121
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 Module Assembly The module assembly is located underneath the enclosure cover. To remove the module assembly, follow these steps: 1. Prepare the Armada MiniStation for disassembly (Section 6.3). 2. Remove the enclosure cover (Section 6.5). 3. Position the Armada MiniStation so the right side is facing forward. 4. Remove the two screws securing the module assembly to the base assembly (Figure 6-7). Figure 6-7.
PAGE 122
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5. Position the Armada MiniStation so the left side is facing forward. 6. Disconnect the power supply cable from the module assembly 2 (Figure 6-8). 7. Remove the two screws securing the module assembly to the base assembly Figure 6-8. Removing the Module Assembly Screws and Disconnecting the Power Supply Cable 6-8 Armada MiniStation Removal and Replacement Procedures 2.
PAGE 123
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8. Lift the module assembly away from the base assembly (Figure 6-9). NOTE: The Armada MiniStation EX module assembly includes a multiple-pin connector that is firmly connected to the MultiBay/PC Card assembly. Pull firmly to disconnect the module assembly from the MultiBay/PC Card assembly. Figure 6-9.
PAGE 124
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . To install the module assembly, follow these steps: 1. Align the alignment pins on the bottom of the module assembly with the holes in the base assembly 1 and place the module assembly on the base assembly (Figure 6-10). 2. Press firmly on the front of the module assembly to properly seat the module assembly connector board. 3. Install the two screws assembly. 2 on the right side (the side with the docking lever) of the 4.
PAGE 125
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.7 Power Supply The screws securing the module assembly to the base assembly also secure the power supply. Once these screws have been removed (Section 6.7), the power supply can also be removed. To remove the power supply, follow these steps: 1. Prepare the Armada MiniStation for disassembly (Section 6.3). 2. Remove the enclosure cover (Section 6.5). 3. Remove the module assembly (Section 6.6). 4.
PAGE 126
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8 MultiBay/PC Card Assembly (Armada MiniStation EX only) The MultiBay/PC Card Assembly provides the Armada MiniStation EX with a MultiBay, a battery charging bay, and two PC Card slots. MultiBay devices supported by the computer and ArmadaStation can be used in the Armada MiniStation EX. CAUTION: Be careful when removing and installing the MultiBay/PC Card assembly.
PAGE 127
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Remove the five screws securing the MultiBay/PC Card assembly to the base assembly (Figure 6-12). 4. Remove the MultiBay/PC Card assembly. NOTE: The MultiBay/PC Card assembly includes a multiple-pin connector that is firmly connected to the module assembly. Pull firmly to disconnect the MultiBay/PC Card assembly from the module assembly. Figure 6-12.
PAGE 128
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 7 Specifications This chapter provides physical and performance specifications for the ArmadaStation and Armada MiniStation. 7.1 ArmadaStation Physical and Environmental Specifications Table 7-1 ArmadaStation Physical and Environmental Specifications Dimensions Height With Monitor Support Cover Without Monitor Support Cover Depth Width Weight ArmadaStation Monitor Support Cover U.S. Metric 5.6 in 5.0 in 16.0 in 17.
PAGE 129
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 Armada MiniStation Physical and Environmental Specifications Table 7-2 Armada MiniStation Physical and Environmental Specifications Dimensions Height With Monitor Support Cover Without Monitor Support Cover Depth Width Weight Armada MiniStation E Armada MiniStation EX Monitor Support Cover U.S. Metric 5.60 in 5.00 in 15.37 in 14.75 in 14.20 cm 12.70 cm 39.05 cm 37.47 cm 7.67 lb 11.50 lb 3.30 lb 3.48 kg 5.23 kg 1.
PAGE 130
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix A Connector Pin Assignments This appendix contains the pin assignments for all external connectors.
PAGE 131
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 132
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 133
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 134
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Table A-13 Docking Connector Pin Signal Pin Signal 1 EBOXL 34 XA1/R OUT 2 AGND 35 GND 3 EBOXS1 36 GND 4 RED 37 EXPCLK2 5 AGND 38 +3.
PAGE 135
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 136
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 137
Connector Pin Assignments A-8
PAGE 138
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix B Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the Compaq ArmadaStation and Armada MiniStation permit them to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord sets received with the ArmadaStation and Armada MiniStation meet the requirements for use in the country where the equipment is purchased.
PAGE 139
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 140
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 141
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 142
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 143
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 144
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 145
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 146
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 147
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .