Maintenance and Service Guide HP Pavilion ze2200 Notebook PC Compaq Presario M2200 Notebook PC ✎ The information and procedures included in this Maintenance and Service Guide apply to all Compaq Presario M2200 Notebook PC models and to the following HP Pavilion ze2200 Notebook PC models: ■ ■ ■ ■ ■ ze2201AP ze2201XX ze2202AP ze2203AP ze2204AP ■ ■ ■ ■ ■ ze2205AP ze2206AP ze2207AP ze2208AP ze2209AP ■ ■ ■ ■ ■ ze2209XX ze2210AP ze2211AP ze2250EA ze2281EA To verify the applicability of spare parts kits t
© Copyright 2005 Hewlett-Packard Development Company, L.P. Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Intel, Pentium, Celeron, and Centrino are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. The information contained herein is subject to change without notice.
Contents 1 Product Description 1.1 1.2 1.3 1.4 1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 Resetting the Notebook . . . . . . . . . . . . . . . . . . . . . . . 1–4 Power Management. . . . . . . . . . . . . . . . . . . . . . . . . . 1–5 External Components . . . . . . . . . . . . . . . . . . . . . . . . 1–6 Design Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 1–32 2 Troubleshooting 2.1 Computer Setup. . . . . . . . . . . . . . . . . . . . . . . . .
Contents 3.4 Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . 3–16 3.5 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–18 3.6 Sequential Part Number Listing . . . . . . . . . . . . . . . 3–19 4 Removal and Replacement Preliminaries 4.1 Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Service Considerations . . . . . . . . . . . . . . . . . . . . . . . Plastic Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 5.10 5.11 5.12 5.13 5.14 5.15 5.16 5.17 5.18 5.19 5.20 5.21 5.22 5.23 LED Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display Assembly . . . . . . . . . . . . . . . . . . . . . . . . . Base Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Speaker Assembly. . . . . . . . . . . . . . . . . . . . . . . . . Heat Sink. . . .
Contents A Connector Pin Assignments B Power Cord Set Requirements 3-Conductor Power Cord Set . . . . . . . . . . . . . . . . . . . . . . B–1 General Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . B–2 Country-Specific Requirements . . . . . . . . . . . . . . . . . . . .
1 Product Description The HP Pavilion ze2200 Notebook PC 1 and the Compaq Presario M2200 Notebook PC 2 offer advanced modularity, Intel® Mobile Pentium® M and Celeron® M processors, and extensive multimedia support.
Product Description 1.1 Features references are made throughout this Maintenance and ✎ Numerous Service Guide to “full-featured” and “defeatured” notebook models. A model is considered to be full-featured if it has 3 Universal Serial Bus ports and the following components: ■ S-Video-out jack ■ Expansion port 2 ■ 6-in-1 Digital Media Slot or 6-in-1 Memory Reader A notebook model is considered to be defeatured if it has only 2 Universal Serial Bus ports and none of the components in the preceding list.
Product Description ■ 15.0-inch XGA (1024 × 768) TFT display with over 16.7 million colors ■ 80-, 60-, or 40-GB high-capacity hard drive, varying by notebook model ■ 256-MB DDR2 synchronous DRAM (SDRAM) at 400 MHz, expandable to 1.
Product Description ■ Connectors: ❏ External monitor port ❏ Universal Serial Bus (USB) v. 2.0 (up to 3 ports) ❏ RJ-11 (modem) jack ❏ RJ-45 (network) jack ❏ Audio-out (headphone) jack ❏ Audio-in (microphone) jack ❏ Power ❏ IEEE 1394 digital port ❏ S-Video-out jack (select models only) ❏ Expansion port 2 (select models only) ❏ 6-in-1 Digital Media Slot (select models only) ❏ 6-in-1 Memory Reader (select models only) 1.
Product Description 1.3 Power Management The notebook comes with power management features that extend battery operating time and conserve power.
Product Description 1.4 External Components The external components on the front of the HP Pavilion ze2200 notebook are shown below and described in Table 1-1.
Product Description Table 1-1 Front Components HP Pavilion ze2200 Item Component Function 1 Speakers (2) Produce stereo sound. 2 Wireless light (select models only) On: One or more optional internal wireless devices, such as a WLAN and/or a Bluetooth® device (select models only), are turned on. 3 Power/standby light ■ On: Notebook is turned on. ■ Blinking: Notebook is in standby. ■ Off: Notebook is off.
Product Description The external components on the front of the Compaq Presario M2200 notebook are shown below and described in Table 1-2.
Product Description Table 1-2 Front Components Compaq Presario M2200 Item Component Function 1 Speakers (2) Produce stereo sound. 2 Wireless light (select models only) On: One or more optional internal wireless devices, such as a WLAN and/or a Bluetooth device (select models only), are turned on. 3 Power/standby light ■ On: Notebook is turned on. ■ Blinking: Notebook is in standby. ■ Off: Notebook is off.
Product Description The external components on the right side of the HP Pavilion ze2200 notebook are shown below and described in Table 1-3.
Product Description Table 1-3 Right-Side Components HP Pavilion ze2200 Item Component Function 1 USB ports (1 or 2 depending on the notebook model) Connect an optional USB device. 2 6-in-1 Digital Media Slot (select models only) Supports an optional digital memory card. 3 1394 port (select models only) Connects an optional 1394a device such as a scanner, digital camera, or digital camcorder. 4 6-in-1 Digital Media Slot light (select models only) On: A digital memory card is being accessed.
Product Description The external components on the right side of the Compaq Presario M2200 notebook are shown below and described in Table 1-4.
Product Description Table 1-4 Right-Side Components Compaq Presario M2200 Item Component Function 1 USB ports (1 or 2 depending on the notebook model) Connect optional USB devices. 2 6-in-1 Memory Reader (select models only) Supports an optional digital memory card. 3 1394 port (select models only) Connects an optional 1394a device such as a scanner, digital camera, or digital camcorder. 4 6-in-1 Memory Reader light (select models only) On: A digital memory card is being accessed.
Product Description The external components on the left side of the HP Pavilion ze2200 notebook are shown below and described in Table 1-5.
Product Description Table 1-5 Left-Side Components HP Pavilion ze2200 Item Component Function 1 Power connector Connects an AC adapter cable. 2 Monitor port Connects an optional VGA monitor or projector. 3 Expansion port 2* (select models only) Connects the notebook to an optional docking device. 4 RJ-45 jack Connects an optional network cable. 5 RJ-11 jack Connects the modem cable. 6 USB port Connects an optional USB device.
Product Description The external components on the left side of the Compaq Presario M2200 notebook are shown below and described in Table 1-6.
Product Description Table 1-6 Left-Side Components Compaq Presario M2200 Item Component Function 1 Power connector Connects an AC adapter cable. 2 Monitor port Connects an optional VGA monitor or projector. 3 Expansion port 2* (select models only) Connects the notebook to an optional docking device. 4 RJ-45 (network) jack Connects an optional network cable. 5 RJ-11 (modem) jack Connects the modem cable. 6 USB port Connects an optional USB device.
Product Description The external components on the rear panel of the HP Pavilion ze2200 notebook are shown below and described in Table 1-7. Rear Panel Components, HP Pavilion ze2200 Table 1-7 Rear Panel Components HP Pavilion ze2200 Item Component Function 1 Battery bay Holds a battery pack. 2 Exhaust vent Provides airflow to cool internal components. Ä 1–18 To prevent overheating, do not obstruct vents.
Product Description The external components on the rear panel of the Compaq Presario M2200 notebook are shown below and described in Table 1-8. Rear Panel Components, Compaq Presario M2200 Table 1-8 Rear Panel Components Compaq Presario M2200 Item Component Function 1 Battery bay Holds a battery pack. 2 Exhaust vent Provides airflow to cool internal components. Ä To prevent overheating, do not obstruct vents.
Product Description The notebook keyboard components on the HP Pavilion ze2200 notebook are shown below and described in Table 1-9.
Product Description Table 1-9 Keyboard Components HP Pavilion ze2200 Item Component Function 1 Function keys (12) Perform system and application tasks. When combined with the fn key, several keys perform additional tasks as hotkeys. 2 caps lock key Enables caps lock and turns on the caps lock light. 3 fn key Combines with other keys to perform system tasks. For example, pressing fn+f7 decreases screen brightness. 4 Windows logo key Displays the Windows Start menu.
Product Description The notebook keyboard components on the Compaq Presario M2200 notebook are shown below and described in Table 1-10.
Product Description Table 1-10 Keyboard Components Compaq Presario M2200 Item Component Function 1 Function keys (12) Perform system and application tasks. When combined with the Fn key, the function keys perform additional tasks as hotkeys. 2 caps lock key Enables caps lock and turns on the caps lock light. 3 Fn key Combines with other keys to perform system tasks. For example, pressing Fn+F7 decreases screen brightness. 4 Windows logo key Displays the Windows Start menu.
Product Description The notebook top components on the HP Pavilion ze2200 notebook are shown below and described in Table 1-11. Top Components, HP Pavilion ze2200 Table 1-11 Top Components HP Pavilion ze2200 Item Component Function 1 Left and right TouchPad buttons Function like the left and right buttons on an external mouse. 2 TouchPad Moves the pointer. 3 Caps lock light On: Caps lock is on. 4 Display switch If the notebook is closed while on, initiates standby.
Product Description Table 1-11 Top Components HP Pavilion ze2200 (Continued) Item Component Function 5 Power/standby button When the notebook is ■ Off, press to turn on the notebook. ■ On, briefly press to initiate hibernation. ■ In standby, briefly press to resume from standby. ■ In hibernation, briefly press to restore from hibernation. system has stopped responding ✎ IfandtheWindows shutdown procedures cannot be used, press and hold for at least 4 seconds to turn off the notebook.
Product Description The top components on the Compaq Presario M2200 notebook are shown below and described in Table 1-12. Top Components, Compaq Presario M2200 Table 1-12 Top Components Compaq Presario M2200 Item Component Function 1 Left and right TouchPad buttons Function like the left and right buttons on an external mouse. 2 TouchPad Moves the pointer. 3 Caps lock light On: Caps lock is on. 4 Display switch If the notebook is closed while on, initiates standby.
Product Description Table 1-12 Top Components Compaq Presario M2200 (Continued) Item Component Function 5 Wireless light (select models only) On: One or more optional internal wireless devices, such as a WLAN and/or a Bluetooth device (select models only), are turned on. 6 Power/standby button When the notebook is ■ Off, press to turn on the notebook. ■ On, briefly press to initiate hibernation. ■ In standby, briefly press to resume from standby.
Product Description The external components on the bottom of the HP Pavilion ze2200 notebook are shown below and described in Table 1-13. Bottom Components, HP Pavilion ze2200 Table 1-13 Bottom Components HP Pavilion ze2200 Item Component Function 1 Battery bay Holds a battery pack. 2 Battery pack release latch Releases a battery pack from the battery bay. 3 Memory module compartment Contains two memory module slots that support replaceable memory modules.
Product Description Table 1-13 Bottom Components HP Pavilion ze2200 (Continued) Item Component Function 4 Exhaust vents (4) Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Do not allow a hard surface, such as a printer, or a soft surface, such as pillows, thick rugs or clothing, to block airflow. 5 Optical drive Supports an optical disc. 6 Label area Contains the notebook serial number and other applicable regulatory labels.
Product Description The external components on the bottom of the Compaq Presario M2200 notebook are shown below and described in Table 1-14. Bottom Components, Compaq Presario M2200 Table 1-14 Bottom Components Compaq Presario M2200 Item Component Function 1 Battery bay Holds a battery pack. 2 Battery pack release latch Releases a battery pack from the battery bay. 3 Memory module compartment Contains two memory module slots that support replaceable memory modules.
Product Description Table 1-14 Bottom Components Compaq Presario M2200 (Continued) Item Component Function 4 Exhaust vents (4) Provide airflow to cool internal components. Ä To prevent overheating, do not obstruct vents. Do not allow a hard surface, such as a printer, or a soft surface, such as pillows, thick rugs, or clothing, to block airflow. 5 Optical drive Supports an optical disc. 6 Label area Contains the notebook serial number and other applicable regulatory labels.
Product Description 1.5 Design Overview This section presents a design overview of key parts and features of the notebook. Refer to Chapter 3, “Illustrated Parts Catalog,” to identify replacement parts, and Chapter 5, “Removal and Replacement Procedures,” for disassembly steps.
2 Troubleshooting Å WARNING: Only authorized technicians trained by HP should repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly-/module-level repair. Because of the complexity of the individual boards and subassemblies, do not attempt to make repairs at the component level or modifications to any printed wiring board. Improper repairs can create a safety hazard.
Troubleshooting Accessing Computer Setup The information and settings in Computer Setup are accessed from the Main, Security, Advanced, Tools, and Exit menus. 1. Open Computer Setup by turning on or restarting the notebook. Press f10 while the “Press to enter Setup” message is displayed in the lower-left corner of the screen. ❏ To change the language, use the arrow keys to select the Advanced menu, select Language Support, and then press f5 or f6 until the appropriate language is highlighted.
Troubleshooting Computer Setup Defaults To return all settings in Computer Setup to the values that were set at the factory: 1. Open Computer Setup by turning on or restarting the notebook. Press f10 while the “Press to enter Setup” message is displayed in the lower-left corner of the screen. ❏ To change the language, use the arrow keys to select the Advanced menu, select Language Support, and then press f5 or f6 until the appropriate language is highlighted.
Troubleshooting Selecting from the Main Menu Table 2-1 Main Menu Select To Do This System Information ■ View identification information about the notebook. ■ View specification information about the processor, memory and cache size, keyboard controller version, and system BIOS. Selecting from the Security Menu Table 2-2 Security Menu Select To Do This Administrator password Enter, change, or delete an HP Administrator password. Power-on password Enter, change, or delete a power-on password.
Troubleshooting Selecting from the Advanced Menu Table 2-3 Advanced Menu Select To Do This Video Graphic Mode Select UMA, SidePort, or UMA+SidePort video memory modes. Dedicated Video Memory View the size of the on-board video memory. Total Video Memory View the size of the total system video memory. Language Support Change the Computer Setup language. Boot Order Set the boot order.
Troubleshooting Table 2-5 Exit Menu Select To Do This Exit Saving Changes Save changes entered during the current session. Then exit and restart the notebook. The changes you save are in effect when the notebook restarts. Exit Discarding Changes Cancel changes entered during the current session. Then exit and restart the notebook. Load Setup Defaults Replace configuration settings in Computer Setup with factory default settings. (Identification information is retained.
Troubleshooting 2.2 Troubleshooting Flowcharts Table 2-6 Troubleshooting Flowcharts Overview Flowchart Description 2.1 “Flowchart 2.1—Initial Troubleshooting” 2.2 “Flowchart 2.2—No Power, Part 1” 2.3 “Flowchart 2.3—No Power, Part 2” 2.4 “Flowchart 2.4—No Power, Part 3” 2.5 “Flowchart 2.5—No Power, Part 4” 2.6 “Flowchart 2.6—No Video, Part 1” 2.7 “Flowchart 2.7—No Video, Part 2” 2.8 “Flowchart 2.8—Nonfunctioning Docking Device (if applicable)” 2.9 “Flowchart 2.
Troubleshooting Table 2-6 Troubleshooting Flowcharts Overview (Continued) Flowchart Description 2.14 “Flowchart 2.14—No OS Loading, Optical Drive” 2.15 “Flowchart 2.15—No Audio, Part 1” 2.16 “Flowchart 2.16—No Audio, Part 2” 2.17 “Flowchart 2.17—Nonfunctioning Device” 2.18 “Flowchart 2.18—Nonfunctioning Keyboard” 2.19 “Flowchart 2.19—Nonfunctioning Pointing Device” 2.20 “Flowchart 2.
Troubleshooting Flowchart 2.1—Initial Troubleshooting Begin troubleshooting. N Go to Is there power? “Flowchart 2.2—No Power, Part 1.” Y N Check LED board, speaker connections. Beeps, LEDs, or error messages? N Y Go to All drives working? N Go to Is there video? (no boot) Y “Flowchart 2.6—No Video, Part 1.” N Keyboard/ pointing device working? Y N Go to Is the OS loading? N Go to Is there sound? Y “Flowchart 2.9—No Operating System (OS) Loading.” Y “Flowchart 2.15—No Audio, Part 1.
Troubleshooting Flowchart 2.2—No Power, Part 1 No power (power LED is off). Remove from docking device (if applicable). N N Power up on battery power? Go to Power up on battery power? Reset power.* “Flowchart 2.3—No Power, Part 2.” Y Y N N Power up on AC power? Power up on AC power? Reset power.* Y Go to “Flowchart 2.4—No Power, Part 3.” Y Y Power up in docking device? Done N 1. Reseat the power cables in the docking device and at the AC outlet. 2. Ensure the AC power source is active.
Troubleshooting Flowchart 2.3—No Power, Part 2 Continued from “Flowchart 2.2—No Power, Part 1.” Visually check for debris in battery socket and clean if necessary. Y Power on? Done N Check battery by recharging it, moving it to another notebook, or replacing it. N Replace power supply (if applicable). Power on? Y N Go to Done Power on? “Flowchart 2.4—No Power, Part 3.
Troubleshooting Flowchart 2.4—No Power, Part 3 Continued from “Flowchart 2.3—No Power, Part 2.” Plug directly into AC outlet. Y Power LED on? Done N Reseat AC adapter in notebook and at power source. Y Done Power on? N External N Try different outlet. Power outlet active? Y Internal or external AC adapter? Replace external AC adapter. N Internal Go to “Flowchart 2.5—No Power, Part 4.” Replace power cord.
Troubleshooting Flowchart 2.5—No Power, Part 4 Continued from “Flowchart 2.4—No Power, Part 3.” Open notebook. Y Loose or damaged parts? N Reseat loose components and boards and replace damaged items. Close notebook and retest. N Power on? Y Done Replace the following items (if applicable). Check notebook operation after each replacement: 1. Internal DC-DC converter* 2. Internal AC adapter 3. Processor board* 4.
Troubleshooting Flowchart 2.6—No Video, Part 1 No video. Docking Device Go to Stand-alone or docking device? *NOTE: To change from internal to external display, use the hotkey combination. “Flowchart 2.7—No Video, Part 2.” Stand-alone Internal or external display*? Y Adjust brightness. A Adjust brightness. Press lid switch to ensure operation. Y Video OK? Done N Internal External Video OK? Y Done N Video OK? Done N Replace the following one at a time. Test after each replacement. 1.
Troubleshooting Flowchart 2.7—No Video, Part 2 Continued from “Flowchart 2.6—No Video, Part 1.” Remove notebook from docking device, if connected. Adjust display brightness. Check brightness of external monitor. N Y Go to “A” in “Flowchart 2.6—No Video, Part 1.” Video OK? Y Video OK? Done N Check that notebook is properly seated in docking device, for bent pins on cable, and for monitor connection. Try another external monitor.
Troubleshooting Flowchart 2.8—Nonfunctioning Docking Device (if applicable) Nonfunctioning docking device. Reseat power cord in docking device and power outlet. Check voltage setting on docking device. Reinstall notebook into docking device. Y Reset monitor cable connector at docking device. Docking device operating? N Y Docking device operating? N Done Done Test replacement docking device with new notebook. Remove notebook, replace docking device.
Troubleshooting Flowchart 2.9—No Operating System (OS) Loading No OS loading.* Reseat power cord in docking device and power outlet. No OS loading from hard drive, go to “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” No OS loading from diskette drive, go to “Flowchart 2.13—No OS Loading, Diskette Drive.” No OS loading from optical drive, go to “Flowchart 2.14—No OS Loading, Optical Drive.” No OS loading from network, go to “Flowchart 2.20—No Network/Modem Connection.
Troubleshooting Flowchart 2.10—No OS Loading, Hard Drive, Part 1 OS not loading from hard drive. Y Nonsystem disk message? N Go to “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” Reseat external hard drive. Y OS loading? Done N N Boot from CD? N Y Boot from diskette? Check the Setup utility for correct booting order. Y Change boot priority through the Setup utility and reboot. N Boot from hard drive? N Y Boot from hard drive? Done Y 2–18 Go to “Flowchart 2.
Troubleshooting Flowchart 2.11—No OS Loading, Hard Drive, Part 2 Continued from “Flowchart 2.10—No OS Loading, Hard Drive, Part 1.” Reseat hard drive. N 1. Replace hard drive. 2. Replace system board. Disc or diskette in drive? Y Y Hard drive accessible? Done N Remove disc or diskette and reboot. Run FDISK. Y Boot from hard drive? N Done N Hard drive partitioned? Y N Y N Go to “Flowchart 2.13—No OS Loading, Diskette Drive.
Troubleshooting Flowchart 2.12—No OS Loading, Hard Drive, Part 3 Continued from “Flowchart 2.11—No OS Loading, Hard Drive, Part 2.” N System files on hard drive? Install OS and reboot. Y Y Y Virus on hard drive? OS loading from hard drive? Clean virus. N Done N Y Run SCANDISK and check for bad sectors. Diagnostics on disc or diskette? Replace hard drive. N N Can bad sectors be fixed? Run diagnostics and follow recommendations. Replace hard drive. Y N Boot from hard drive? Fix bad sectors.
Troubleshooting Flowchart 2.13—No OS Loading, Diskette Drive Y OS not loading from diskette drive. Reseat diskette drive. OS loading? Done N Y N Bootable diskette in drive? Nonsystem disk message? N Y N Check diskette for system files. Try different diskette. Go to Boot from another device? “Flowchart 2.17—Nonfunctioning Device.” Y Y N Diskette drive enabled in the Setup utility? Enable drive and cold boot notebook.
Troubleshooting Flowchart 2.14—No OS Loading, Optical Drive Y No OS loading from CD-ROM or DVD-ROM drive. N Install bootable disc and reboot notebook. Bootable disc in drive? Disc in drive? Y N Install bootable disc. Try another bootable disc. Y Boots from CD or DVD? Done N Y Boots from CD or DVD? Reseat drive. Done N N Booting from another device? Y Y Booting order correct? N Go to “Flowchart 2.17—Nonfunctioning Device.” Reset the notebook. Refer to Go to Section 1.
Troubleshooting Flowchart 2.15—No Audio, Part 1 Y Turn up audio internally or externally. No audio. Audio? Done N Y Notebook in docking device (if applicable)? N Go to Internal audio? Undock N “Flowchart 2.16—No Audio, Part 2.” Y Go to Dock notebook in replacement docking device. “Flowchart 2.16—No Audio, Part 2.” Y Go to “Flowchart 2.17—Nonfunctioning Device.
Troubleshooting Flowchart 2.16—No Audio, Part 2 Continued from “Flowchart 2.15—No Audio, Part 1.” N Audio driver in OS configured? Reload audio drivers. Y N Correct drivers for application? Load drivers and set configuration in OS. Y Connect to external speaker. N Audio? Y Replace audio board and speaker connections in notebook (if applicable).
Troubleshooting Flowchart 2.17—Nonfunctioning Device Nonfunctioning device. Reseat device. Unplug the nonfunctioning device from the notebook and inspect cables and plugs for bent or broken pins or other damage. Y Clear CMOS. Fix or replace broken item. Any physical device detected? N Reattach device. Close notebook, plug in power, and reboot. Go to “Flowchart 2.9—No Operating System (OS) Loading.” Replace hard drive. N Device boots properly? N Replace NIC.
Troubleshooting Flowchart 2.18—Nonfunctioning Keyboard Keyboard not operating properly. Connect notebook to good external keyboard. N External device works? Replace system board. Y Reseat internal keyboard connector (if applicable). N Keyboard operating properly? Replace internal keyboard or cable. Y Y Keyboard operating properly? Done Done N Replace system board.
Troubleshooting Flowchart 2.19—Nonfunctioning Pointing Device Pointing device not operating properly. Connect notebook to good external pointing device. N Replace system board. External device works? Y Reseat internal pointing device connector (if applicable). N Replace internal pointing device or cable. Pointing device operating properly? Y Y Pointing device operating properly? Done Done N Replace system board.
Troubleshooting Flowchart 2.20—No Network/Modem Connection No network or modem connection. N Network or modem jack active? Replace jack or have jack activated. Y Y Connect to nondigital line. Digital line? N Y N NIC/modem configured in OS? Network or modem connection working? Reload drivers and reconfigure. Done N Y Disconnect all power from the notebook and open. Replace NIC/modem (if applicable). Reseat NIC/modem (if applicable).
3 Illustrated Parts Catalog This chapter provides an illustrated parts breakdown and a reference for spare part numbers and option part numbers. 3.1 Serial Number Location When ordering parts or requesting information, provide the notebook serial number and model number located on the bottom of the notebook.
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components Item Description 1 Display assemblies (include wireless antenna boards and cables) Spare Part Number 15.0-inch, XGA TFT, for use on HP Pavilion ze2200 models 381065-001 15.
Illustrated Parts Catalog Notebook Major Components, Compaq Presario M2200 3–4 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Item Description 4 Keyboards Spare Part Number For use on HP Pavilion ze2200 models in: Belgium Brazil Denmark Europe and The Netherlands France French Canada Germany Greece Israel Italy Korea Norway 381068-A41 381068-201 381068-081 381068-331 381068-051 381068-121 381068-041 381068-151 381068-BB1 381068-061 381068-AD1 381068-091 Portugal Saudi Arabia Spain Sweden/Finland Switzerland Taiwan United Kingdom Asia Pac
Illustrated Parts Catalog Notebook Major Components, HP Pavilion ze2200 3–6 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Item Description 5 Top covers (include TouchPad) 6 Spare Part Number For use on full-featured HP Pavilion ze2200 models For use on defeatured HP Pavilion ze2200 models 382396-001 382905-001 For use on full-featured Compaq Presario M2200 models For use on defeatured Compaq Presario M2200 models 382397-001 382906-001 Speaker assemblies For use on HP Pavilion ze2200 models 382410-001 For use on Compaq Presario M
Illustrated Parts Catalog Notebook Major Components, Compaq Presario M2200 3–8 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Item Description 12 Processors (include thermal pad) Spare Part Number Intel Pentium M 745 (1.8-GHz) with 400-MHz FSB Intel Pentium M 735 (1.7-GHz) with 400-MHz FSB Intel Pentium M 725 (1.6-GHz) with 400-MHz FSB Intel Pentium M 715 (1.5-GHz) with 400-MHz FSB Intel Pentium M 715A (1.5-GHz) with 400-MHz FSB Intel Celeron M 370 (1.5-GHz) with 400-MHz FSB Intel Celeron M 360 (1.
Illustrated Parts Catalog Notebook Major Components, HP Pavilion ze2200 3–10 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Item Description Spare Part Number Miscellaneous Plastics Kit 17a 17b 17c 18 For use on HP Pavilion ze2200 models 382400-001 For use on Compaq Presario M2200 models 382401-001 Includes: Hard drive cover (includes two captive screws) Memory module compartment cover (includes 2 captive screws) Mini PCI compartment cover (includes 2 captive screws) Not illustrated: PC Card slot space saver Notebook feet (4) Mini P
Illustrated Parts Catalog Notebook Major Components, HP Pavilion ze2200 3–12 Maintenance and Service Guide
Illustrated Parts Catalog Table 3-1 Spare Parts: Notebook Major Components (Continued) Item Description 20 Optical drives (include bezel) 21 Spare Part Number For use on HP Pavilion ze2200 models: 8X DVD-ROM drive 24X DVD/CD-RW Combo Drive 8X DVD±RW/R and CD-RW Combo Drive 8X DVD±RW/R and CD-RW Combo Dual Layer Drive 381399-001 381401-001 381403-001 390141-001 For use on Compaq Presario M2200 models: 8X DVD-ROM drive 24X DVD/CD-RW Combo Drive 8X DVD±RW/R and CD-RW Combo Drive 8X DVD±RW/R and CD-RW
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-2 Miscellaneous Plastics Kit Spare Part Number Information Item Description Spare Part Number Miscellaneous Plastics Kit 1 2 3 4 5 For use on HP Pavilion ze2200 models 382400-001 For use on Compaq Presario M2200 models 382401-001 Includes: Memory module compartment cover Mini PCI compartment cover Hard drive cover PC Card slot space saver Notebook feet (4) Maintenance and Service Guide 3–15
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-3 Mass Storage Devices Spare Part Number Information Spare Part Number Item Description 1 Hard drives (all 4200-rpm; include frame and connector) 80-GB 60-GB 40-GB 2 381398-001 381397-001 381396-001 Optical drives For use on HP Pavilion ze2200 models 8X DVD-ROM drive 24X DVD/CD-RW Combo Drive 8X DVD±RW/R and CD-RW Combo Drive 8X DVD±RW/R and CD-RW Combo Dual Layer Drive 381399-001 381401-001 381403-001 390141-001 For use on Compaq Presario M2200 models 8X DVD-ROM
Illustrated Parts Catalog 3.
Illustrated Parts Catalog Table 3-4 Spare Parts: Miscellaneous (not illustrated) (Continued) Spare Part Number Description Power cords For use in: Australia and New Zealand 373979-011 Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden 373979-021 Brazil 373979-201 Canada, French Canada, Latin America, Thailand, and The United States 373979-001 Denmark 373979-081 Hong Kong and the United Kingdom 373979-031 Israel 373979-BB1 Italy 373979-061
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) 309674-001 USB travel mouse 364727-001 USB digital drive 367759-001 Battery pack, 6-cell, 4.4-AHr 367760-001 Battery pack, 12-cell, 8.8-AHr 367771-001 Processor, Intel Pentium M 725 (1.
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 367777-AB1 Keyboard for use on Compaq Presario M2200 models in Taiwan 367777-AD1 Keyboard for use on Compaq Presario M2200 models in Korea 367777-B71 Keyboard for use on Compaq Presario M2200 models in Sweden/Finland 371693-001 Wired headset with volume control 371790-001 65-watt AC adapter 373023-001 Mini PCI communications card, 802.
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 373979-001 Power cord for use in Canada, French Canada, Latin America, Taiwan, Thailand, and the United States 373979-011 Power cord for use in Australia and New Zealand 373979-021 Power cord for use in Belgium, Europe, Finland, France, Germany, Greece, the Netherlands, Norway, Portugal, Spain, and Sweden 373979-031 Power cord for use in Hong Kong and the United Kingdom 373979
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 381066-001 Display assembly, 15.
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 381068-AD1 Keyboard for use on HP Pavilion ze2200 models in Korea 381068-B71 Keyboard for use on HP Pavilion ze2200 models in Sweden/Finland 381068-BB1 Keyboard for use on HP Pavilion ze2200 models in Israel 381394-001 Memory module, 256-MB (266 MHz) 381395-001 Memory module, 512-MB (266 MHz) 381396-001 Hard drive, 4200-rpm, 40-GB (includes frame and connector) 381397-001
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 382399-001 Base enclosure for use on Compaq Presario M2200 models 382400-001 Miscellaneous Plastics Kit for use on HP Pavilion ze2200 models 382401-001 Miscellaneous Plastics Kit for use on Compaq Presario M2200 models 382402-001 Screw Kit for use on HP Pavilion ze2200 models 382403-001 Screw Kit For use on Compaq Presario M2200 models 382404-001 Logo Kit for use on HP Pavi
Illustrated Parts Catalog Table 3-5 Spare Parts: Sequential Part Number Listing (Continued) Spare Part Number Description 382417-001 Display hinge brackets for use on HP Pavilion ze2200 models 382418-001 Hinge covers (for use only on Compaq Presario M2200 models) 382905-001 Top cover for use on defeatured HP Pavilion ze2200 models (includes TouchPad) 382906-001 Top cover for use on defeatured Compaq Presario M2200 models (includes TouchPad) 382907-001 LED board for use on Compaq Presario M2200 m
4 Removal and Replacement Preliminaries This chapter provides essential information for proper and safe removal and replacement service. 4.1 Tools Required You will need the following tools to complete the removal and replacement procedures: ■ Magnetic screwdriver ■ Phillips P0 screwdriver ■ 5.
Removal and Replacement Preliminaries 4.2 Service Considerations The following sections include some of the considerations that you should keep in mind during disassembly and assembly procedures. you remove each subassembly from the notebook, place ✎ As the subassembly (and all accompanying s) away from the work area to prevent damage. Plastic Parts Using excessive force during disassembly and reassembly can damage plastic parts. Use care when handling the plastic parts.
Removal and Replacement Preliminaries 4.3 Preventing Damage to Removable Drives Removable drives are fragile components that must be handled with care. To prevent damage to the notebook, damage to a removable drive, or loss of information, observe the following precautions: ■ Before removing or inserting a hard drive, shut down the notebook. If you are unsure whether the notebook is off or in hibernation, turn the notebook on, and then shut it down through the operating system.
Removal and Replacement Preliminaries 4.4 Preventing Electrostatic Damage Many electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, the discharge contains enough power to alter device parameters or melt silicon junctions.
Removal and Replacement Preliminaries 4.5 Packaging and Transporting Precautions Use the following grounding precautions when packaging and transporting equipment: ■ To avoid hand contact, transport products in static-safe containers, such as tubes, bags, or boxes. ■ Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers or packaging. ■ Keep electrostatic-sensitive parts in their containers until the parts arrive at static-free workstations.
Removal and Replacement Preliminaries 4.6 Workstation Precautions Use the following grounding precautions at workstations: ■ Cover the workstation with approved static-shielding material (refer to Table 4-2, “Static-Shielding Materials”). ■ Use a wrist strap connected to a properly grounded work surface and use properly grounded tools and equipment. ■ Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
Removal and Replacement Preliminaries Other grounding equipment recommended for use in preventing electrostatic damage includes: ■ Antistatic tape ■ Antistatic smocks, aprons, and sleeve protectors ■ Conductive bins and other assembly or soldering aids ■ Nonconductive foam ■ Conductive tabletop workstations with ground cords of one megohm resistance ■ Static-dissipative tables or floor mats with hard ties to the ground ■ Field service kits ■ Static awareness labels ■ Material-handling packages ■ Nonconduct
Removal and Replacement Preliminaries Table 4-1 shows how humidity affects the electrostatic voltage levels generated by different activities.
5 Removal and Replacement Procedures This chapter provides removal and replacement procedures. There are 66 screws, in 8 different sizes, that must be removed, replaced, or loosened when servicing the notebook. Make special note of each screw size and location during removal and replacement. Refer to Appendix C, “Screw Listing,” for detailed information on screw sizes, locations, and usage.
Removal and Replacement Procedures 5.1 Serial Number Report the notebook serial number to HP when requesting information or ordering spare parts. The serial number is located on the bottom of the notebook.
Removal and Replacement Procedures 5.2 Disassembly Sequence Chart Use the chart below to determine the section number to be referenced when removing notebook components. Disassembly Sequence Chart Section Description 5.3 Preparing the Notebook for Disassembly # of Screws Removed Battery pack 0 5.4 Hard Drive 2 loosened to remove the hard drive cover 4 removed to disassemble the hard drive 5.5 Notebook Feet 0 5.6 Optical Drive 1 5.
Removal and Replacement Procedures Disassembly Sequence Chart (Continued) Section Description # of Screws Removed 5.12 Display Assembly HP Pavilion ze2200 = 4 Compaq Presario M2200 = 6 5.13 Base Enclosure HP Pavilion ze2200 = 23 Compaq Presario M2200 = 25 5.14 RTC Battery 0 5.15 Speaker Assembly 0 5.16 Heat Sink 3 5.17 Fan 2 5.18 Processor 1 loosened 5.19 Battery Connector Board 2 5.20 Power Connector Board 2 5.21 USB/S-Video Controller Board 1 5.22 Bluetooth Board 2 5.
Removal and Replacement Procedures 5.3 Preparing the Notebook for Disassembly Before you begin any removal or installation procedures: 1. Shut down the notebook. If you are unsure whether the notebook is off or in hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the notebook. 3. Disconnect the power cord. Battery Pack Spare Part Number Information 12-cell, 8.8-AHr 6-cell, 4.4-AHr 367760-001 367759-001 4.
Removal and Replacement Procedures b. Slide and hold the battery release latch 1 to the left. (The front edge of the battery pack disengages from the notebook.) c. Lift the front edge of the battery pack 2 up and swing it back. d. Remove the battery pack. Removing the Battery Pack Reverse the above procedure to install the battery pack. 5.
Removal and Replacement Procedures 5. Remove the hard drive by following these steps: a. Position the notebook with the rear panel toward you. b. Loosen the two PM2.0×5.0 screws 1 that secure the hard drive cover to the notebook. c. Lift the right side of the cover 2 and swing it to the left. d. Remove the hard drive cover.
Removal and Replacement Procedures e. Grasp the mylar tab 1 and lift the hard drive until it disconnects from the notebook. f. Remove the hard drive 2 from the hard drive bay.
Removal and Replacement Procedures g. Remove the four PM2.5×4.0 screws 1 that secure the hard drive frame to the hard drive. h. Lift the frame 2 up to remove if from the hard drive. i. Slide the hard drive connector 3 toward you and remove it. Removing the Hard Drive Frame and Connector Reverse the above procedure to reassemble and install the hard drive.
Removal and Replacement Procedures 5.5 Notebook Feet The notebook feet are adhesive-backed rubber pads. The feet are included in the Miscellaneous Plastics Kits, spare part numbers 382400-001 (for use on HP Pavilion ze2200 models) and 382401-001 (for use on Compaq Presario M2200 models). The feet attach to the base enclosure as illustrated below.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 2. Remove the PM2.0×7.0 screw 1 that secures the optical drive to the notebook. 3. Insert a thin tool, such as a paper clip, into the media tray release hole 2. (The optical drive media tray releases from the optical drive.) 4. Use the media tray frame to slide the optical drive 3 to the right. 5. Remove the optical drive. Removing the Optical Drive Reverse the above procedure to install an optical drive.
Removal and Replacement Procedures 5.7 Memory Module Memory Module Spare Part Number Information 512-MB 256-MB 381395-001 381394-001 1. Prepare the notebook for disassembly (refer to Section 5.3).
Removal and Replacement Procedures 2. Position the notebook with the rear panel toward you. 3. Loosen the two PM2.0×5.0 screws 1 that secure the memory module compartment cover to the notebook. 4. Lift the rear edge of the memory module compartment cover 2 up and swing it toward you. 5. Remove the memory module compartment cover.
Removal and Replacement Procedures 6. Spread the retaining tabs 1 on each side of the memory module socket to release the memory module. (The right side of the module rises away from the notebook.) 7. Slide the module 2 away from the socket at an angle. modules are designed with security slots 3 to prevent ✎ Memory incorrect installation into the memory module socket. Removing the Memory Module Reverse the above procedure to install a memory module.
Removal and Replacement Procedures 5.8 Mini PCI Communications Card Mini PCI Communications Card Spare Part Number Information 802.11b/g Broadcomm (for use in most of the world) 802.11b/g Broadcomm (for use in the rest of the world) 802.11b Intel (for use in most of the world) 802.11b Intel (for use in the rest of the world) 802.11b/g Intel (for use in most of the world) 802.11b/g Intel (for use in the rest of the world) 373047-001 373048-001 373023-001 373024-001 373025-001 373026-001 1.
Removal and Replacement Procedures 4. Loosen the PM2.0×5.0 screw 1 that secures the Mini PCI compartment cover to the notebook. 5. Lift the rear edge of the Mini PCI compartment cover 2 up and then swing it toward you. 6. Remove the Mini PCI compartment cover. Mini PCI compartment cover is included in the ✎ The Miscellaneous Plastics Kits, spare part numbers 382400-001 (for use on HP Pavilion ze2200 models) and 382401-001 (for use on Compaq Presario M2200 models).
Removal and Replacement Procedures disconnecting the cables, make note of which wireless ✎ Before antenna cable is attached to which antenna clip on the Mini PCI communications card. 7. Disconnect the wireless antenna cables 1 from the Mini PCI communications card. 8. Spread the two retaining tabs 2 that secure the Mini PCI communications card to the communications compartment socket. (The front edge of the board rises up). 9.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 3. Remove the two PM2.0×8.0 screws that secure the keyboard cover to the notebook.
Removal and Replacement Procedures 4. Turn the notebook display-side up with the front panel toward you. 5. Open the notebook as far as possible. 6. Insert a flat blade tool into the keyboard cover notches behind the f4, f12, and insert keys 1 and lift up 2 until the keyboard cover disengages from the notebook. 7. Remove the keyboard cover. Removing the Keyboard Cover Reverse the above procedure to install the keyboard cover.
Removal and Replacement Procedures 5.10 LED Board LED Board Spare Part Number Information For use on HP Pavilion ze2200 models For use on Compaq Presario M2200 models 382415-001 382907-001 1. Prepare the notebook for disassembly (Section 5.3). 2. Remove the keyboard cover (Section 5.9).
Removal and Replacement Procedures 3. Release the zero insertion force (ZIF) connector to which the keyboard cable is connected and disconnect the keyboard cable 1 from the system board. 4. Remove the two PM2.0×4.0 screws 2 that secure the LED board to the notebook. 5. Remove the LED board 3. Removing the LED Board Reverse the above procedure to install the LED board.
Removal and Replacement Procedures 5.
Removal and Replacement Procedures 3. Remove the four PM2.0×3.0 screws that secure the keyboard to the notebook.
Removal and Replacement Procedures 4. Lift the rear edge of the keyboard and swing it toward you until it rests on the palm rest.
Removal and Replacement Procedures 5. Release the ZIF connector 1 to which the keyboard cable is connected and disconnect the keyboard cable 2 from the system board. 6. Remove the keyboard. Disconnecting the Keyboard Cable Reverse the above procedure to install the keyboard.
Removal and Replacement Procedures 5.12 Display Assembly Display Assembly Spare Part Number Information 15.0-inch, XGA TFT, for use on HP Pavilion ze2200 models (includes wireless antenna boards and cables) 381065-001 15.
Removal and Replacement Procedures 2. Turn the notebook upside down with the front panel toward you. 3. Disconnect the wireless antenna cables from the Mini PCI communications card 1. 4. Remove the cables from the clip 2 in the base enclosure.
Removal and Replacement Procedures 5. Turn the notebook display-side up with the front toward you. 6. Open the display. 7. Disconnect the display cable 1 from the system board. 8. Remove the wireless antenna cables from the clips 2 in the top cover.
Removal and Replacement Procedures Ä CAUTION: Support the display assembly when removing the following screws. Failure to follow this caution can result in damage to the display assembly. 9 and 10 apply only to HP Pavilion ze2200 models. See ✎ Steps steps 11 and 12 in this section for information on removing the display assembly on Compaq Presario M2200 models. 9. Remove the four PM2.0×7.0 screws 1 that secure the display assembly to the notebook. 10. Remove the display assembly 2.
Removal and Replacement Procedures Ä CAUTION: Support the display assembly when removing the following screws. Failure to follow this caution can result in damage to the display assembly. 11 and 12 apply only to Compaq Presario M2200 ✎ Steps models. 11. Remove the six PM2.0×7.0 screws 1 that secure the display assembly to the notebook. 12. Remove the display assembly 2. Removing the Display Assembly, Compaq Presario M2200 Models Only Reverse the above procedure to install the display assembly.
Removal and Replacement Procedures 5.13 Base Enclosure Base Enclosure Spare Part Number Information For use on HP Pavilion ze2200 models For use on Compaq Presario M2200 models 382398-001 382399-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g.
Removal and Replacement Procedures 3 through 5 apply only to HP Pavilion ze2200 models. ✎ Steps See steps 6 through 8 in this section for information on removing the base enclosure screws on Compaq Presario M2200 models. 3. Remove the three PM2.0×8.0 screws 1 and the two PM2.0×4.0 screws 2 that secure the base enclosure to the notebook.
Removal and Replacement Procedures 4. Turn the notebook upside down with the front panel toward you. 5. Remove the following: 1 Five PM2.0×16.0 screws that secure the base enclosure the notebook 2 Seven PM2.0×8.0 screws that secure the base enclosure the notebook 3 Six PM2.0×4.
Removal and Replacement Procedures 6 through 8 apply only to Compaq Presario M2200 ✎ Steps models. 6. Remove the six PM2.0×8.0 screws 1 and the PM2.0×4.0 screw 2 that secure the base enclosure to the notebook.
Removal and Replacement Procedures 7. Turn the notebook upside down with the front panel toward you. 8. Remove the three PM2.0×4.0 screws 1 and the fifteen PM2.0×8.0 screws 2 that secure the base enclosure to the notebook.
Removal and Replacement Procedures 9 and 10 apply to both HP Pavilion ze2200 and ✎ Steps Compaq Presario M2200 models. 9. Lift the rear edge of the base enclosure 1 until it disengages from the notebook. 10. Slide the base enclosure 2 back and remove it. Removing the Base Enclosure Reverse the above procedure to install the base enclosure.
Removal and Replacement Procedures 5.14 RTC Battery RTC battery is spared with the system board spare part ✎ The kits. If the battery needs to be replaced, use an “ML1220” model battery. 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g.
Removal and Replacement Procedures 2. Remove the RTC battery from the socket on the system board. Removing the RTC Battery Reverse the above procedure to install the RTC battery. Make sure the battery is installed with the “+” side facing up.
Removal and Replacement Procedures 5.15 Speaker Assembly Speaker Assembly Spare Part Number Information For use on HP Pavilion ze2200 models For use on Compaq Presario M2200 models 382410-001 383189-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g.
Removal and Replacement Procedures 2. Disconnect the speaker cable 1 from the system board. 3. Lift the speaker 2 straight up to remove it from the top cover. Removing the Speaker Assembly Reverse the above procedure to install the speaker assembly.
Removal and Replacement Procedures 5.16 Heat Sink Heat Sink Spare Part Number Information Heat sink (includes thermal pad) 382412-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g. Keyboard (Section 5.11) h. Display assembly (Section 5.12) i.
Removal and Replacement Procedures 2. Disconnect the fan cable 1 from the system board. 3. Remove the three PM2.0×4.0 screws 2 that secure the heat sink to the top cover. 4. Remove the heat sink 3. Removing the Heat Sink Reverse the above procedure to install the heat sink.
Removal and Replacement Procedures 5.17 Fan Fan Spare Part Number Information Fan (includes thermal pad) 382411-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g. Keyboard (Section 5.11) h. Display assembly (Section 5.12) i.
Removal and Replacement Procedures 3. Remove the two PM2.0×4.0 screws 1 that secure the fan to the heat sink. 4. Remove the fan 2. Removing the Fan Reverse the above procedure to install the fan.
Removal and Replacement Procedures 5.18 Processor Processor Spare Part Number Information Intel Pentium M 745 (1.8-GHz) with 400-MHz FSB Intel Pentium M 735 (1.7-GHz) with 400-MHz FSB Intel Pentium M 725 (1.6-GHz) with 400-MHz FSB Intel Pentium M 715 (1.5-GHz) with 400-MHz FSB Intel Pentium M 715A (1.5-GHz) with 400-MHz FSB 373053-001 373052-001 367771-001 383431-001 380690-001 Intel Celeron M 370 (1.5-GHz) with 400-MHz FSB Intel Celeron M 360 (1.4-GHz) with 400-MHz FSB Intel Celeron M 350 (1.
Removal and Replacement Procedures 2. Turn the processor locking screw 1 one-quarter turn counterclockwise until you feel a click. 3. Lift the processor 2 straight up and remove it. gold triangle 3 on the processor should be aligned in the ✎ The front right corner when you install the processor. Removing the Processor Reverse the above procedure to install a processor.
Removal and Replacement Procedures 5.19 Battery Connector Board Battery Connector Board Spare Part Number Information Battery connector board 382413-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g. Keyboard (Section 5.11) h.
Removal and Replacement Procedures 3. Remove the PM2.0×4.0 screw that secures the battery connector board to the top cover.
Removal and Replacement Procedures 4. Turn the top cover upside down with the front panel toward you. 5. Remove the PM2.0×4.0 screw 1 that secures the battery connector board to the top cover. 6. Slide the battery connector board 2 toward the rear panel until it disconnects from the system board. 7. Remove the battery connector board 3. Removing the Battery Connector Board Reverse the above procedure to install the the battery connector board.
Removal and Replacement Procedures 5.20 Power Connector Board Power Connector Board Spare Part Number Information Power connector board 382414-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g. Keyboard (Section 5.11) h. Display assembly (Section 5.
Removal and Replacement Procedures 2. Remove the two PM2.0×4.0 screws 1 that secure the power connector board to the top cover. 3. Slide the power connector board 2 toward the rear panel until it disconnects it from the system board. 4. Remove the power connector board 3. Removing the Power Connector Board Reverse the above procedure to install the power connector board.
Removal and Replacement Procedures 5.21 USB/S-Video Controller Board ✎ This section applies only to full-featured models. USB/S-Video Controller Board Spare Part Number Information USB/S-Video controller board 382416-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f.
Removal and Replacement Procedures 2. Remove the PM2.0×4.0 screw 1 that secures the USB/S-Video controller board to the top cover. 3. Lift up on the right side of the board 2 to disconnect it from the system board. 4. Remove the USB/S-Video controller board. Removing the USB/S-Video Controller Board Reverse the above procedure to install the USB/S-Video controller board.
Removal and Replacement Procedures 5.22 Bluetooth Board ✎ This section applies only to full-featured models. Bluetooth Board Spare Part Number Information Broadcomm Bluetooth board 376651-001 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Memory module compartment cover (Section 5.7) d. Mini PCI compartment cover (Section 5.8) e. Keyboard cover (Section 5.9) f. LED board (Section 5.10) g.
Removal and Replacement Procedures 3. Remove the two PM1.5×3.5 screws 1 that secure the Bluetooth board to the USB/S-Video controller board. 4. Disconnect the Bluetooth board cable 2 from the USB/S-Video controller board. 5. Remove the Bluetooth board 3. Removing the Bluetooth Board Reverse the above procedure to install the Bluetooth board.
Removal and Replacement Procedures 5.23 System Board System Board Spare Part Number Information For use on full-featured models, 855GM, with Intel Centrino technology 373522-001 For use on full-featured models, 855GM, without Intel Centrino technology 381062-001 For use on defeatured models, 852GM 373523-001 PC Card cage 389525-001 ✎ All system board spares kits include a disk cell RTC battery.
Removal and Replacement Procedures 1. Prepare the notebook for disassembly (Section 5.3) and remove the following components: a. Hard drive (Section 5.4) b. Optical drive (Section 5.6) c. Keyboard cover (Section 5.9) d. LED board (Section 5.10) e. Keyboard (Section 5.11) f. Display assembly (Section 5.12) g. Base enclosure (Section 5.13) h. Speaker assembly (Section 5.15) i. Battery connector board (Section 5.19) j. Power connector board (Section 5.20) k. USB/S-Video controller board (Section 5.21) 2.
Removal and Replacement Procedures 3. Release the ZIF connector 1 to which the TouchPad cable is connected and disconnect the cable 2 from the system board.
Removal and Replacement Procedures 4. Turn the top cover upside down with the front toward you. 5 applies only to HP Pavilion ze2200 models. See step 6 ✎ Step in this section for information on removing the system board screws on Compaq Presario M2200 models. 5. Remove the two PM2.0×4.0 screws that secure the system board to the top cover.
Removal and Replacement Procedures ✎ Step 6 applies only to Compaq Presario M2200 models. 6. Remove the four PM2.0×4.0 screws that secure the system board to the top cover.
Removal and Replacement Procedures 7. Flex the left edge of the top cover 1 out until the 1394 connector 2 disengages from the top cover. 8. Lift the left side of the system board 3 until the 1394 connector is clear. 9. Flex the front edge of the top cover 4 until the audio connectors 5 and LED section 6 of the system board disengage from the top cover.
Removal and Replacement Procedures 10. Slide the system board to the left at an angle and remove it. Removing the System Board Reverse the above procedure to install the system board.
6 Specifications This chapter provides physical and performance specifications. Table 6-1 Notebook Dimensions HP Pavilion ze2200 Height (varies from front to back) Width Depth 3.01 cm to 3.86 cm 23.46 cm 33.40 cm 1.19 in to 1.52 in 9.24 in 13.15 in 3.29 cm to 3.89 cm 23.06 cm 33.40 cm 1.30 in to 1.53 in 9.08 in 13.15 in 2.44 kg 2.39 kg 5.38 lb 5.
Specifications Table 6-1 Notebook (Continued) Temperature Operating Nonoperating 10°C to 35°C -20°C to 60°C 50°F to 95°F -4°F to 140°F Relative humidity (noncondensing) Operating Nonoperating 10% to 90% 5% to 95%, 38.7°C (101.6°F) maximum wet bulb temperature Maximum altitude (unpressurized) Operating (14.7 to 10.1 psia) Nonoperating (14.7 to 4.
Specifications Table 6-2 15.0-inch, XGA, Display Dimensions Height Width Diagonal 22.9 cm 30.0 cm 38.1 cm Number of colors Up to 16.8 million Contrast ratio 250:1 Brightness 150 nits typical 9.0 in 11.8 in 15.0 in Pixel resolution Pitch Format Configuration 0.264 × 0.264 mm 1024 × 768 RGB vertical stripe Backlight Edge lit Character display 80 × 25 Total power consumption 5.
Specifications Table 6-3 Hard Drives 80-GB* 60-GB* 40-GB* 9.5 mm 70 mm 99 g 9.5 mm 70 mm 102 g 9.
Specifications Table 6-4 Primary 6-cell, Li-Ion Battery Pack Dimensions Height Width Depth Weight 2.00 cm 9.40 cm 13.40 cm 0.34 kg 0.79 in 3.70 in 5.28 in 0.75 lb Energy Voltage Amp-hour capacity Watt-hour capacity 11.1 V 4.
Specifications Table 6-5 24X DVD/CD-RW Combo Drive Applicable disc Read: Write: DVD-R, DVD-RW, CD-R and CD-RW DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc 6–6 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-5 24X DVD/CD-RW Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD media DVD media < 110 ms < 210 ms < 130 ms < 225 ms Random Full stroke Audio output level Line-out, 0.7 V rms Cache buffer 2 MB Data transfer rate CD-R (24X) CD-RW (10X) CD-ROM (24X) DVD (8X) Multiword DMA mode 2 3600 KB/s (150 KB/s at 1X CD rate) 1500 KB/s (150 KB/s at 1X CD rate) 3600 KB/s (150 KB/s at 1X CD rate) 10,800 KB/s (1352 KB/s at 1X DVD rate) 16.
Specifications Table 6-6 8X DVD±RW/R and CD-RW Combo Drive Applicable disc Read: DVD-R, DVD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R, CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Write: CD-R and CD-RW DVD-R and DVD-RW Disc diameter Standard disc Mini disc 6–8 12 cm (4.72 in) 8 cm (3.
Specifications Table 6-6 8X DVD±RW/R and CD-RW Combo Drive (Continued) Disc thickness 1.2 mm (0.047 in) Track pitch 0.74 µm Access time CD DVD < 175 ms < 285 ms < 230 ms < 335 ms Random Full stroke Audio output level Audio-out, 0.
Specifications Table 6-7 8X DVD-ROM Drive Applicable disc DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) CD-ROM (Mode 1 and 2) CD Digital Audio CD-XA ready (Mode 2, Form 1 and 2) CD-I ready (Mode 2, Form 1 and 2) CD-R CD-RW Photo CD (single and multisession) CD-Bridge Center hole diameter 1.5 cm (0.59 in) Disc diameter Standard disc Mini disc Disc thickness 6–10 12 cm (4.72 in) 8 cm (3.15 in) 1.2 mm (0.
Specifications Table 6-7 8X DVD-ROM Drive (Continued) Track pitch 0.74 µm Access time CD media DVD media < 100 ms < 175 ms < 125 ms < 225 ms Random Full stroke Audio output level Line-out, 0.7 V rms Cache buffer 512 KB Data transfer rate CD-R (24X) CD-RW (10X) CD-ROM (24X) DVD (8X) Multiword DMA mode 2 3600 KB/s (150 KB/s at 1X CD rate) 1500 KB/s (150 KB/s at 1X CD rate) 3600 KB/s (150 KB/s at 1X CD rate) 10,800 KB/s (1352 KB/s at 1X DVD rate) 16.
Specifications Table 6-8 System DMA Hardware DMA System Function DMA0 Not applicable DMA1 Not applicable DMA2 Not applicable DMA3 Not applicable DMA4 Direct memory access controller DMA5 Available for PC Card DMA6 Not assigned DMA7 Not assigned 6–12 Maintenance and Service Guide
Specifications Table 6-9 System Interrupts Hardware IRQ System Function IRQ0 System timer IRQ1 Quick Launch buttons IRQ2 Cascaded IRQ3 USB2 Enhanced Host Controller—24CD IRQ4 COM1 IRQ5* Conexant AC—Link Audio SMBus Controller—24C3 Data Fax Modem with SmartCP IRQ6 Diskette drive IRQ7* Parallel port IRQ8 System CMOS/real-time clock IRQ9* Microsoft ACPI-compliant system IRQ10* USB UHCI controller—24C2 GM/GME Graphic Controller Realtek RTL8139 Family PCI fast Ethernet Controller IRQ11
Specifications Table 6-9 System Interrupts (Continued) Hardware IRQ System Function IRQ12 Synaptics PS/2 port pointing device IRQ13 Numeric data processor IRQ14 Primary IDE channel IRQ15 Secondary IDE channel IRQ17 Conexant AC -Link Audio IRQ17 Soft V90 Data Fax Modem with SmartCP IRQ17 ATi Mobility Radeon Xpress 200 Series IRQ19 Standard Enhanced PCI to USB Host Controller IRQ19 Standard OpenHCD USB Host Controller IRQ19 Standard OpenHCD USB Host Controller IRQ20 TI 6411 PCIxx21/x51
Specifications Table 6-10 System I/O Addresses I/O Address (hex) System Function (shipping configuration) 0x00000000-0x00000CF7 PCI bus 0x00000000-0x00000CF7 Direct memory access controller 0x00000020-0x00000021 Programmable interrupt controller 0x0000002E-0x0000002F System board resources 0x00000040-0x00000043 System timer 0x00000060-0x00000060 Quick Launch Buttons 0x00000061-0x00000061 System speaker 0x00000062-0x00000062 Microsoft ACPI-Compliant Embedded Controller 0x00000064-0x0000006
Specifications Table 6-10 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0x000001F0-0x000001F7 Primary IDE Channel 0x00000220-0x0000022F System board resources 0x00000274-0x00000277 ISAPNP Read Data Port 0x00000279-0x00000279 ISAPNP Read Data Port 0x00000280-0x00000293 System board resources 0x00000376-0x00000376 Secondary IDE Channel 0x000003B0-0x000003BB PCI standard PCI-to-PCI bridge 0x000003B0-0x000003BB ATI MOBILITY RADEON Xpress 200 Series
Specifications Table 6-10 System I/O Addresses (Continued) I/O Address (hex) System Function (shipping configuration) 0x00000C6F-0x00000C6F System board resources 0x00000CD4-0x00000CD5 System board resources 0x00000CD6-0x00000CD7 System board resources 0x00000CD8-0x00000CDF System board resources 0x00000D00-0x0000FFFF PCI bus 0x00000F40-0x00000F47 System board resources 0x00001080-0x00001080 System board resources 0x00008000-0x0000805F System board resources 0x00008100-0x000081FF System
Specifications Table 6-11 System Memory Map Memory Map Address (hex) System Function (shipping configuration) 0xD4100000-0xD41FFFFF PCI standard PCI-to-PCI bridge 0xD4100000-0xD41FFFFF ATI MOBILITY RADEON Xpress 200 Series 0xD8000000-0xDBFFFFFF PCI standard PCI-to-PCI bridge 0xD8000000-0xDBFFFFFF ATI MOBILITY RADEON Xpress 200 Series 0xFAC00000-0xFEBFFFFF PCI standard PCI-to-PCI bridge 0xF6C00000-0xFABFFFFF PCI standard PCI-to-PCI bridge 0xD4000000-0xD4000FFF Standard OpenHCD USB Host Contro
Specifications Table 6-11 System Memory Map (Continued) Memory Map Address (hex) System Function (shipping configuration) 0xD4208000-0xD42087FF Texas Instruments OHCI Compliant IEEE 1394 Host Controller 0xD4200000-0xD4203FFF Texas Instruments OHCI Compliant IEEE 1394 Host Controller 0xD4204000-0xD4205FFF Broadcom 802.
Specifications Table 6-11 System Memory Map (Continued) Memory Map Address (hex) System Function (shipping configuration) 0xD4209400-0xD42094FF Realtek RTL8139/810x Family Fast Ethernet NIC 0xD4003400-0xD40034FF Conexant AC-Link Audio 0xD4003800-0xD40038FF SoftV90 Data Fax Modem with SmartCP 0xFEC00000-0xFEC00FFF System board resources 0xFEE00000-0xFEE00FFF System board resources 0xA0000-0xBFFFF PCI bus 0xA0000-0xBFFFF PCI standard PCI-to-PCI bridge 0xA0000-0xBFFFF ATI MOBILITY RADEON Xpre
A Connector Pin Assignments Table A-1 Universal Serial Bus Pin Signal Pin Signal 1 +5 VDC 3 Data + 2 Data – 4 Ground Maintenance and Service Guide A–1
Connector Pin Assignments Table A-2 RJ-45 (Network) Pin Signal Pin Signal 1 Transmit + 5 Unused 2 Transmit – 6 Receive – 3 Receive + 7 Unused 4 Unused 8 Unused A–2 Maintenance and Service Guide
Connector Pin Assignments Table A-3 S-Video-Out Pin Signal Pin Signal 1 S-VHS color (C) signal 5 TV-CD 2 Composite video signal 6 S-VHS intensity ground 3 S-VHS intensity (Y) signal 7 Composite video ground 4 S-VHS color ground Maintenance and Service Guide A–3
Connector Pin Assignments Table A-4 External Monitor Pin Signal Pin Signal 1 Red analog 9 +5 VDC 2 Green analog 10 Ground 3 Blue analog 11 Monitor detect 4 Not connected 12 DDC 2B data 5 Ground 13 Horizontal sync 6 Ground analog 14 Vertical sync 7 Ground analog 15 DDC 2B clock 8 Ground analog A–4 Maintenance and Service Guide
Connector Pin Assignments Table A-5 RJ-11 (Modem) Pin Signal Pin Signal 1 Unused 4 Unused 2 Tip 5 Unused 3 Ring 6 Unused Maintenance and Service Guide A–5
Connector Pin Assignments Table A-6 Audio-In (Microphone) Pin Signal Pin Signal 1 Audio signal in 3 Ground 2 Audio signal in Table A-7 Audio-Out (Headphone) Pin Signal Pin Signal 1 Audio out, left channel 3 Ground 2 Audio out, right channel A–6 Maintenance and Service Guide
B Power Cord Set Requirements 3-Conductor Power Cord Set The wide range input feature of the notebook permits it to operate from any line voltage from 100 to 120 or 220 to 240 volts AC. The power cord set included with the notebook meets the requirements for use in the country where the equipment is purchased. Power cord sets for use in other countries must meet the requirements of the country where the notebook is used.
Power Cord Set Requirements General Requirements The requirements listed below are applicable to all countries. B–2 ■ The length of the power cord set must be at least 1.5 m (5.0 ft) and a maximum of 2.0 m (6.5 ft). ■ All power cord sets must be approved by an acceptable accredited agency responsible for evaluation in the country where the power cord set will be used.
Power Cord Set Requirements Country-Specific Requirements 3-Conductor Power Cord Set Requirements Country/Region Accredited Agency Applicable Note Number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
Power Cord Set Requirements 3-Conductor Power Cord Set Requirements (Continued) Country/Region Accredited Agency Applicable Note Number Korea EK 4 The Netherlands KEMA 1 Norway NEMKO 1 People’s Republic of China CCC 5 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 United Kingdom BSI 1 United States UL 2 ✎ NOTES: 1. The flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm² conductor size.
C Screw Listing This appendix provides specification and reference information for the screws used in the notebook. All screws listed in this appendix are available in the Miscellaneous Screw Kits, spare part numbers 382402-001 (for use on HP Pavilion ze2200 models) and 382403-001 (for use on Compaq Presario M2200 models).
Screw Listing Table C-1 Phillips PM2.0×5.0 Screw mm Color Qty. Length Thread Head Width Black 5 5.0 mm 2.0 mm 4.0 mm Where used: 1 Two screws that secure the hard drive cover to the notebook (screws are captured on the cover by C clips; documented in Section 5.4) 2 Two screws that secure the memory module compartment cover to the notebook (screws are captured on the cover by C clips; documented in Section 5.
Screw Listing Table C-2 Phillips PM2.5×4.0 Screw mm Color Qty. Length Thread Head Width Silver 4 4.0 mm 2.5 mm 4.0 mm Where used: 4 screws that secure the hard drive frame to the hard drive (documented in Section 5.4) Phillips PM2.5×4.
Screw Listing Table C-3 Phillips PM2.0×7.0 Screw mm Color Qty. Length Thread Head Width Black 11 7.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the optical drive to the notebook (documented in Section 5.6) Phillips PM2.0×7.
Screw Listing Table C-3 Phillips PM2.0×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 11 7.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the display assembly on the HP Pavilion ze2200 notebook (documented in Section 5.12) Phillips PM2.0×7.
Screw Listing Table C-3 Phillips PM2.0×7.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 11 7.0 mm 2.0 mm 4.0 mm Where used: 6 screws that secure the display assembly on the Compaq Presario M2200 notebook (documented in Section 5.12) Phillips PM2.0×7.
Screw Listing Table C-4 Phillips PM2.0×8.0 Screw mm Color Qty. Length Thread Head Width Black 33 8.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the keyboard cover to the notebook (documented in Section 5.9) Phillips PM2.0×8.
Screw Listing 2 Table C-4 Phillips PM2.0×8.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 33 8.0 mm 2.0 mm 4.0 mm Where used: 3 screws that secure the base enclosure to the notebook on the HP Pavilion ze2200 notebook (documented in Section 5.13) Phillips PM2.0×8.
Screw Listing Table C-4 Phillips PM2.0×8.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 33 8.0 mm 2.0 mm 4.0 mm Where used: 7 screws that secure the base enclosure to the notebook on the HP Pavilion ze2200 notebook (documented in Section 5.13) Phillips PM2.0×8.
Screw Listing Table C-4 Phillips PM2.0×8.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 33 8.0 mm 2.0 mm 4.0 mm Where used: 6 screws that secure the base enclosure on the Compaq Presario M2200 notebook (documented in Section 5.13) Phillips PM2.0×8.
Screw Listing Table C-4 Phillips PM2.0×8.0 Screw (Continued) mm Color Qty. Length Thread Head Width Black 33 8.0 mm 2.0 mm 4.0 mm Where used: 15 screws that secure the base enclosure on the Compaq Presario M2200 notebook (documented in Section 5.13) Phillips PM2.0×8.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the LED board to the notebook (documented in Section 5.10) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the base enclosure to the HP Pavilion ze2200 notebook (documented in Section 5.13) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 6 screws that secure the base enclosure to the HP Pavilion ze2200 notebook (documented in Section 5.13) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the base enclosure to the Compaq Presario M2200 notebook (documented in Section 5.13) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 3 screws that secure the base enclosure on the Compaq Presario M2200 notebook (documented in Section 5.13) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 1 Three screws that secure the heat sink to the notebook (documented in Section 5.16) 2 One screw that secures the battery connector board to the notebook (documented in Section 5.19) 3 Two screws that secure the power connector board to the notebook (documented in Section 5.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the fan to the heat sink (documented in Section 5.17) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: One screw that secures the battery connector board to notebook (documented in Section 5.19) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 2 screws that secure the system board on the HP Pavilion ze2200 notebook (documented in Section 5.23) Phillips PM2.0×4.
Screw Listing Table C-5 Phillips PM2.0×4.0 Screw (Continued) mm Color Qty. Length Thread Head Width Silver 30 4.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the system board on the Compaq Presario M2200 notebook (documented in Section 5.23) Phillips PM2.0×4.
Screw Listing Table C-6 Phillips PM2.0×3.0 Screw mm Color Qty. Length Thread Head Width Black 4 3.0 mm 2.0 mm 4.0 mm Where used: 4 screws that secure the keyboard to the notebook (documented in Section 5.11) Phillips PM2.0×3.
Screw Listing Table C-7 Phillips PM2.0×16.0 Screw mm Color Qty. Length Thread Head Width Black 5 16.0 mm 2.0 mm 4.0 mm Where used: 5 screws that secure the base enclosure on the HP Pavilion ze2200 notebook (documented in Section 5.13) Phillips PM2.0×16.
Screw Listing Table C-8 Phillips PM1.5×3.5 Screw mm Color Qty. Length Thread Head Width Silver 2 3.5 mm 1.5 mm 3.0 mm Where used: 2 screws that secure the Bluetooth board to the notebook (documented in Section 5.22) Phillips PM1.5×3.
Index 1394 port 1–11, 1–13 6-in-1 Digital Media Slot light 1–11, 1–25 6-in-1 Digital Media Slot 1–11 6-in-1 Memory Reader 1–13 6-in-1 Memory Reader light 1–13, 1–27 A AC adapter, spare part number 3–18, 3–21 arrow keys 1–21, 1–23 audio troubleshooting 2–23 audio-in jack location 1–7, 1–9 pin assignments A–6 audio-out jack location 1–7, 1–9 pin assignments A–6 B base enclosure removal 5–33 spare part numbers 3–9, 3–24, 3–25, 5–33 battery bay 1–18, 1–19, 1–28, 1–30 Maintenance and Service Guide battery co
Index left-side 1–14, 1–16 rear 1–16, 1–18, 1–19 right-side 1–10, 1–12 top 1–24, 1–26 Computer Setup Advanced Menu 2–5 File Menu 2–4 overview 2–1 Security Menu 2–4 Tools Menu 2–5 Computer Setup defaults 2–3 connector pin assignments audio-in A–6 audio-out A–6 external monitor A–4 headphone A–6 microphone A–6 modem A–5 monitor A–4 network A–2 RJ-11 A–5 RJ-45 A–2 S-Video-out A–3 Universal Serial Bus (USB) A–1 connectors, service considerations 4–2 D design overview 1–32 disassembly sequence chart 5–3 disket
Index E electrostatic discharge 4–4, 4–8 exhaust vents 1–18, 1–19, 1–29, 1–31 expansion port 2 1–15, 1–17 external monitor port location 1–15, 1–17 pin assignments A–4 nonfunctioning keyboard 2–26 nonfunctioning pointing device 2–27 fn key 1–21, 1–23 front components 1–6, 1–8 function keys 1–21, 1–23 G F grounding equipment and methods 4–6 fan H removal 5–45 spare part number 3–7, 3–25, 5–45 features 1–2 feet illustrated 3–14 locations 5–10 flowcharts, troubleshooting no audio 2–23, 2–24 no network/
Index I I/O address specifications 6–15 IDE drive light 1–7, 1–9 interrupt specifications 6–13 K keyboard removal 5–24 spare part numbers 3–5, 3–20, 3–21, 3–23, 3–24, 5–24 troubleshooting 2–26 keyboard components 1–20, 1–22 keyboard cover removal 5–19 spare part numbers 3–3, 3–25, 5–19 keypad keys 1–21, 1–23 L label area 1–29, 1–31 LED board removal 5–22 spare part numbers 3–3, 3–25, 3–26, 5–22 left-side components 1–14, 1–16 Logo Kit, spare part numbers 3–18, 3–25 M mass storage devices, spare part num
Index mouse, spare part number 3–18, 3–20 mute button 1–25, 1–27 mute light 1–25, 1–27 N network jack location 1–15, 1–17 pin assignments A–2 network, troubleshooting 2–28 nonfunctioning device, troubleshooting 2–16, 2–25 notebook feet illustrated 3–14 locations 5–10 notebook specifications 6–1 num lock key 1–21, 1–23 num lock light 1–25, 1–27 O optical drive location 1–11, 1–13, 1–29, 1–31 OS loading problems 2–22 precautions 4–3 removal 5–11 spare part numbers 3–13, 3–17, 3–24, 3–26 specifications 6–6,
Index RJ-45 jack location 1–15, 1–17 pin assignments A–2 S Screw Kit, spare part number 3–18, 3–25 screw listing C–1 security cable slot 1–11, 1–13 serial number 3–1, 5–2 service considerations 4–2 speaker assembly removal 5–41 spare part numbers 3–7, 3–25, 3–26, 5–41 speakers 1–7, 1–9 specifications battery pack 6–5 display 6–3 DMA 6–12 DVD/CD-RW Combo Drive 6–6 DVD±RW/R and CD-RW Combo Drive 6–8 DVD-ROM drive 6–10 hard drive 6–4 I/O addresses 6–15 interrupts 6–13 memory map 6–18 notebook 6–1 static shie
Index U Universal Serial Bus (USB) port location 1–11, 1–13, 1–15, 1–17 pin assignments A–1 USB digital drive, spare part number 3–17, 3–20 USB travel mouse, spare part number 3–18, 3–20 USB/S-Video controller board removal 5–54 spare part numbers 3–7, 3–25, 5–54 V video troubleshooting 2–14 volume button 1–25, 1–27 W Windows applications key 1–21, 1–23 Windows logo key 1–21, 1–23 wireless button 1–25 wireless light 1–7, 1–9, 1–27 workstation precautions 4–6 Maintenance and Service Guide Index–7
