HP ProBook 4415s Notebook PC HP ProBook 4416s Notebook PC HP ProBook 4515s Notebook PC Maintenance and Service Guide
© Copyright 2009 Hewlett-Packard Development Company, L.P. AMD Athlon, AMD Sempron, AMD Turion, and ATI Radeon are trademarks of Advanced Micro Devices, Inc. Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard Company under license. Intel is a registered trademark of Intel Corporation in the United States and other countries. Microsoft, Windows, and Windows Vista are U.S. registered trademarks of Microsoft Corporation. SD Logo is a trademark of its proprietor.
MSG revision history Revision Publication date Description A October 2009 ● Updated commodities in the following location: Product description on page 1.
iv MSG revision history
Safety warning notice WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow.
vi Safety warning notice
Table of contents 1 Product description 2 External component identification Windows Vista and Windows XP ....................................................................................................... 10 Display ............................................................................................................................... 10 Top components ................................................................................................................ 11 Pointing devices ............
Plastics Kit .......................................................................................................................................... 42 Cable Kit ............................................................................................................................................. 43 Mass storage devices ......................................................................................................................... 44 Miscellaneous parts ....................................
5 Computer Setup Computer Setup in Windows Vista and Windows XP ...................................................................... 110 Starting Computer Setup ................................................................................................. 110 Using Computer Setup .................................................................................................... 110 Navigating and selecting in Computer Setup ..................................................
Phillips PM2.0×3.0 screw ................................................................................................................. 144 Phillips PM2.5×6.0 screw ................................................................................................................. 145 Phillips PM2.5×11.0 captive screw ................................................................................................... 146 Phillips PM3.0×4.0 screw ...............................................................
Index .................................................................................................................................................................
xii
1 Product description Category Description Product Name HP ProBook 4415s Notebook PC 14.0-in UMA 4415s 14.0-in Discrete 4416s √ HP ProBook 4416s Notebook PC 15.6-in Discrete 4515s √ √ HP ProBook 4515s Notebook PC Processors 15.6-in UMA 4515s √ √ AMD Turion™ II Ultra Dual-Core Mobile M600 2.4-GHz processor, 2MB L2 cache √ √ √ √ AMD Turion II Dual-Core Mobile M520 2.3-GHz processor, 1-MB L2 cache √ √ √ √ AMD Turion II Dual-Core Mobile M500 2.
Category Chipset Description 14.0-in UMA 4415s 15.6-in UMA 4515s 15.6-in Discrete 4515s AMD Athlon QL-64 2.1GHz processor, 1-MB L2 cache √ √ √ √ AMD Athlon QL-66 2.2-GHz processor, 1-MB L2 cache √ √ √ √ AMD Sempron™ M100 2.0-GHz processor, 512-GB L2 cache √ √ √ √ AMD Sempron SI-42 2.
Category Memory Hard drives Description 14.0-in UMA 4415s 14.0-in Discrete 4416s 15.6-in UMA 4515s 15.6-in Discrete 4515s 15.6-in HD AntiGlare without webcam √ √ 15.6-in HD AntiGlare with webcam √ √ 15.6-in HD AntiGlare with webcam and WWAN √ √ 15.6-in HD BrightView without webcam √ √ 15.6-in HD BrightView with webcam √ √ 15.
Category Description Supports the following drives: Optical drives 14.0-in Discrete 4416s 15.6-in UMA 4515s 15.6-in Discrete 4515s √ √ √ √ HP 3D DriveGuard √ √ √ √ Fixed (removal of 1 screw required) √ √ √ √ Supports no optical drive option √ √ √ √ 12.
Category Wireless Description 14.0-in UMA 4415s 14.0-in Discrete 4416s √ √ √ √ Integrated WLAN options by way of MiniPCI card √ √ √ √ 2 WLAN antennas built into display assembly √ √ √ √ Support for no-WLAN option √ √ √ √ Support for the following WLAN formats: √ √ √ √ Wireless personal area network (WPAN) by way of Bluetooth® module: √ √ √ √ Support for no-WPAN option √ √ √ √ Bluetooth 2.0 module √ √ √ √ Bluetooth 2.
Category Keyboard/ pointing devices Description 14.0-in UMA 4415s 14.0-in Discrete 4416s √ √ √ √ High-Definition Multimedia Interface (HDMI) √ √ √ √ Multi-pin AC power √ √ √ √ 14.0-in keyboard with TouchPad √ √ √ √ √ √ TouchPad supports 2-way scroll (taps enabled as default) Security Operating system 6 15.6-in Discrete 4515s VGA (Dsub 15-pin) supporting 1600 × 1200 external resolution at 75GHz (hot plug/unplug with autodetect) 15.6-in/17.
Category Description 14.0-in UMA 4415s 14.0-in Discrete 4416s 15.6-in UMA 4515s 15.
Category Description 14.0-in UMA 4415s 14.0-in Discrete 4416s 15.6-in UMA 4515s 15.
Category Serviceability Description 14.0-in UMA 4415s 14.0-in Discrete 4416s 15.6-in UMA 4515s 15.
2 External component identification Windows Vista and Windows XP Display NOTE: 10 Your computer may look slightly different from the illustration in this section. Component Description (1) Internal display switch Turns off the display if the display is closed while the power is on. (2) Internal microphone Records sound. (3) Webcam light (select models only) On: The webcam is in use. (4) Webcam (select models only) Records audio and video and captures still photographs.
Top components Pointing devices Component Description (1) TouchPad* Moves the pointer and selects or activates items on the screen. (2) Left TouchPad button* Functions like the left button on an external mouse. (3) TouchPad scroll zone Scrolls up or down. (4) Right TouchPad button* Functions like the right button on an external mouse. *This table describes factory settings.
Lights NOTE: Component Description (1) Caps lock light On: Caps lock is on. (2) Info Center/QuickLook light ● On: The computer is on. ● Blinking (5 times): (3) 12 Your computer may look slightly different from the illustration in this section. Power light Chapter 2 External component identification ◦ When the computer is on, press button to launch Info Center. ◦ When the computer is off or in Hibernation, press button to launch QuickLook.
Buttons, switches, and speakers NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) Speakers (2) Produce sound. (2) Internal display switch Turns off the display if the display is closed while the power is on. (3) Info Center/Quick Look button Launches Info Center or QuickLook. (4) Power button ● When the computer is off, press the button to turn on the computer.
Keys NOTE: 14 Refer to the illustration that most closely matches your computer. Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer.
Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Windows logo key Displays the Windows Start menu. (4) Windows applications key Displays a shortcut menu for items beneath the pointer. (5) Integrated numeric keypad keys Can be used like the keys on an external numeric keypad.
Front components Component Description (1) ● Blinking turquoise: The hard drive or optical drive is being accessed. ● Amber: HP 3D DriveGuard has temporarily parked the hard drive. (2) Drive light Wireless switch Turns the wireless feature on or off but does not establish a wireless connection. NOTE: You must set up or access a wireless network to establish a wireless connection.
Right-side components Component Description (1) USB ports (2) Connect optional USB devices. (2) RJ-11 (modem) jack (select models only) Connects a modem cable. (3) Optical drive (select models only) Reads optical discs and, on select models, also writes to optical discs. (4) Optical drive light (select models only) Blinking: The optical drive is being accessed. (5) Battery light ● Amber: A battery is charging. ● Turquoise: A battery is close to full charge capacity.
Left-side components Component Description (1) ExpressCard slot Supports optional ExpressCards. (2) Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (3) RJ-45 (network) jack Connects a network cable. (4) Vent Enables airflow to cool internal components.
Bottom components Component Description (1) Battery release latches (2) Release the battery from the battery bay. (2) Battery bay Holds the battery. Wireless antennas Component Description (1) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN).
Component Description (2) Send and receive wireless signals to communicate with wireless local area networks (WLAN). WLAN antennas (2)* *To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region. These notices are located in Help and Support. NOTE: The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions.
Linux Display NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) Internal display switch Turns off the display if the display is closed while the power is on. (2) Internal microphone Records sound. (3) Webcam light (select models only) On: The webcam is in use. (4) Webcam (select models only) Records audio and video and captures still photographs.
Top components Pointing devices 22 Component Description (1) TouchPad Moves the pointer and selects or activates items on the screen. (2) Left TouchPad button Functions like the left button on an external mouse. (3) TouchPad scroll zone Scrolls up or down. (4) Right TouchPad button Functions like the right button on an external mouse.
Lights NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) Caps lock light On: Caps lock is on. (2) Info Center/QuickLook light ● On: The computer is on. ● Blinking (5 times): (3) Power light ◦ When the computer is on, press button to launch Info Center. ◦ When the computer is off or in Hibernation, press button to launch QuickLook. ● Off: The computer is off or in the Suspend or Hibernation state. ● On: The computer is on.
Buttons, switch, and speakers NOTE: Your computer may look slightly different from the illustration in this section. Component Description (1) Speakers (2) Produce sound. (2) Internal display switch Turns off the display if the display is closed while the power is on. (3) Info Center/QuickLook button Launches Info Center or QuickLook. (4) Power button ● When the computer is off, press the button to turn on the computer. ● When the computer is on, press the button to shut down the computer.
Keys NOTE: Refer to the illustration that most closely matches your computer. Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key, the num lk key, or the esc key. (3) Function keys Execute frequently used system functions when pressed in combination with the fn key.
26 Component Description (1) esc key Displays system information when pressed in combination with the fn key. (2) fn key Executes frequently used system functions when pressed in combination with a function key or the esc key. (3) Function keys Execute frequently used system functions when pressed in combination with the fn key. (4) Integrated numeric keypad keys Can be used like the keys on an external numeric keypad.
Front components Component Description (1) Drive light Blinking turquoise: The hard drive or optical drive is being accessed. (2) Wireless switch Turns the wireless feature on or off but does not establish a wireless connection. NOTE: You must set up or access a wireless network to establish a wireless connection.
Right-side components Component Description (1) USB ports (2) Connect optional USB devices. (2) RJ-11 (modem) jack (select models only) Connects a modem cable. (3) Optical drive (select models only) Reads optical discs and, on select models, also writes to optical discs. (4) Optical drive light (select models only) Blinking: The optical drive is being accessed. (5) Battery light ● Amber: A battery is charging. ● Turquoise: A battery is close to full charge capacity.
Left-side components Component Description (1) ExpressCard slot Supports optional ExpressCards. (2) Security cable slot Attaches an optional security cable to the computer. NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen. (3) RJ-45 (network) jack Connects a network cable. (4) Vent Enables airflow to cool internal components.
Bottom components 30 Component Description (1) Battery release latches (2) Release the battery from the battery bay. (2) Battery bay Holds the battery.
Wireless antennas Component Description (1) WWAN antennas (2)* (select models only) Send and receive wireless signals to communicate with wireless wide-area networks (WWAN). (2) WLAN antennas (2)* Send and receive wireless signals to communicate with wireless local area networks (WLAN). *To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental Notices that applies to your country or region.
Additional hardware components Component Description (1) Power cord* Connects an AC adapter to an AC outlet. (2) Battery* Powers the computer when the computer is not plugged into external power. (3) AC adapter Converts AC power to DC power. *Batteries and power cords vary in appearance by country or region.
3 Illustrated parts catalog Service tag The service tag, affixed to the bottom of the computer, provides information that may be needed when troubleshooting system problems. The service tag provides the following information: (1) Product name: This is the product name affixed to the front of the computer. (2) Serial number (s/n): This is an alphanumeric identifier that is unique to each product.
Computer major components Item Description (1) Display assembly (includes 2 WLAN antenna transceivers and cables) Spare part number For use only with black computers with 15.
Item Description Spare part number ● AntiGlare display assembly for use on computers equipped with a webcam and WWAN module 536794-001 ● BrightView display assembly for use on computers equipped with a webcam and WWAN module 536795-001 For use only with red computers with 15.
Item (5) (6) (7) Description Spare part number For use in red computers with 15.6-in displays 572728-001 For use in black computers with 14.0-in displays 535867-001 For use in red computers with 14.0-in displays 572727-001 Speakers For use in computers with 15.6-in displays 536598-001 For use in computers with 14.0-in displays 536420-001 Top cover For use in computers with 15.6-in displays 535866-001 For use in computers with 14.
Item (12) Description Spare part number For use only in models with the following system boards: 585218-001, 585219-001, 585220-001, 585221-001 537921-001 Processor (includes replacement thermal material) (not illustrated) AMD Turion II Ultra Dual-Core processors (for use only with the following system boards: 585218-001, 585219-001, 585220-001, 585221-001) ● M500 (2.2-GHz with 1-MB L2 cache) 576253-001 ● M520 (2.3-GHz with 1-MB L2 cache) 583055-001 ● M600 (2.
Item Description Spare part number ● 504664-002 For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad, Chile, the People's Republic of China, Colombia,
Item (17) Description Spare part number 1-GB 535809-001 2-GB 535810-001 WWAN module For use in all countries and regions except China 483377-002 For use in China 571888-001 Including GPS, UNDP (United Nations Development Program; not available with Linux) 531993-001 (18) Subscriber identification module (SIM) 536599-001 (19) Base enclosure (20) (21) (22) (23) For use in computers with 15.6-in displays 535864-001 For use in computers with 14.
Display assembly components Item Description (1) Display bezel (2) For use in computers with 15.6-in displays with a webcam 536421-001 For use in computers with 15.6-in displays without a webcam 536424-001 For use in computers with 14.0-in displays with a webcam 536423-001 For use in computers with 14.0-in displays without a webcam 536422-001 Display Hinge Kit For use in computers with 15.
Item (3) Description Spare part number For use in computers with 14.0-in displays 535871-001 Webcam module 535797-001 Display Cable Kit For use in computers with 15.6-in HD displays 536433-001 For use in computers with 14.0-in displays 536430-001 (4a) Microphone cable (4b) WLAN antenna receivers and cables (4c) WWAN antenna receivers and cables (4d) Display/webcam cable Display/webcam cable for use in computers with 15.
Plastics Kit Item 42 Description Spare part number Plastics Kit: 535780-001 (1) ExpressCard slot bezel (2) Optical drive bezel Chapter 3 Illustrated parts catalog
Cable Kit Item Description Spare part number Cable Kit For use only with computers with 14.0-in displays 536538-001 For use only with computers with 15.
Mass storage devices Item Description (1) Hard drives (include bracket) (2) 44 Spare part number 500-GB, 7200-rpm 575125-001 500-GB, 5400-rpm 535814-001 320-GB, 7200-rpm 575124-001 320-GB, 5400-rpm (for use only in models with the following system boards: 535803-001, 574505-001, 574506-001) 535813-001 250-GB, 7200-rpm 536783-001 250-GB, 5400-rpm (for use only in models with the following system boards: 535803-001, 574505-001, 574506-001) 535812-001 160-GB, 7200-rpm 536782-001 160-GB, 5
Miscellaneous parts Description Spare part number AC adapters 65-W AC adapter 463958-001 90-W AC adapter (for use in all countries and regions except India) 463955-001 90-W non-PFC AC adapter (for use only in India) 463956-001 90-W PFC AC adapter (for use only in India) 535593-001 Power cords: For use in the United States 246959-001 For use in Australia and New Zealand 246959-011 For use in Europe, the Middle East, and Africa 246959-021 For use in the United Kingdom 246959-031 For use in I
Sequential part number listing 46 Spare part number Description 246959-001 Power cord for use in the United States 246959-011 Power cord for use in Australia and New Zealand 246959-021 Power cord for use in Europe, the Middle East, and Africa 246959-031 Power cord for use in the United Kingdom 246959-061 Power cord for use in Italy 246959-081 Power cord for use in Demanrk 246959-201 Power cord for use in Brazil 246959-291 Power cord for use in Japan 246959-AD1 Power cord for use in Kore
Spare part number Description 504664-001 Broadcom 4322 802.11a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States 504664-002 Broadcom 4322 802.
48 Spare part number Description 535804-001 Heat sink for use in computers with UMA graphics subsystems 535805-001 Heat sink for use in computers with discrete graphics subsystems 536418-001 6-cell, 47-Wh Li-ion battery for use in computers with 15.6-in displays 535753-001 8-cell, 63-Wh Li-ion battery for use in computers with 15.
Spare part number Description 536410-AD1 Keyboard for use in Korea on computers with 14.0-in 536420-001 Speakers for use in computers with 14.0-in displays 536421-001 Display bezel for use on computers with 15.6-in displays with a webcam 536422-001 Display bezel for use on computers with 14.0-in displays without a webcam 536423-001 Display bezel for use on computers with 14.0-in displays with a webcam 536424-001 Display bezel for use on computers with 15.
50 Spare part number Description 536537-A41 Keyboard for use in Europe on computers with 15.6-in displays 536537-AB1 Keyboard for use in Taiwan on computers with 15.6-in displays 536537-AD1 Keyboard for use in South Korea on computers with 15.6-in displays 536537-B31 Keyboard for International use on computers with 15.6-in displays 536537-B71 Keyboard for use in Europe on computers with 15.6-in displays 536537-BA1 Keyboard for Slovenia use on computers with 15.
Spare part number Description 572727-001 Palm rest for use in red computers with 14.0-in displays (includes TouchPad) 572728-001 Palm rest for use in red computers with 15.6-in displays (includes TouchPad) 572747-001 AMD Athlon QL-66, 2.2-GHz processor with 1-GB L2 cache (for use only with the following system boards: 574505-001, 574506-001, 585802-001, 585803-001) 572748-001 AMD Turion RM-76, 2.
52 Spare part number Description 585218-001 System board for use in computers with a WWAN module and UMA graphics subsystem memory that use AMD Mxxx processors 585219-001 System board for use in computers without a WWAN module and UMA graphics subsystem memory that use AMD Mxxx processors 585220-001 System board for use in computers with a WWAN module and discrete graphics subsystem memory that use AMD Mxxx processors 585221-001 System board for use in computers without a WWAN module and discrete
4 Removal and replacement procedures Preliminary replacement requirements Tools required You will need the following tools to complete the removal and replacement procedures: ● Flat-bladed screwdriver ● Phillips P0 and P1 screwdrivers ● Torx T8 screwdriver Service considerations The following sections include some of the considerations that you must keep in mind during disassembly and assembly procedures.
Cables and connectors CAUTION: When servicing the computer, be sure that cables are placed in their proper locations during the reassembly process. Improper cable placement can damage the computer. Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In all cases, avoid bending, twisting, or tearing cables.
Grounding guidelines Electrostatic discharge damage Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure determine the degree of sensitivity. Networks built into many integrated circuits provide some protection, but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions. A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or microcircuitry.
Packaging and transporting guidelines Follow these grounding guidelines when packaging and transporting equipment: ● To avoid hand contact, transport products in static-safe tubes, bags, or boxes. ● Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging. ● Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations. ● Place items on a grounded surface before removing items from their containers.
Equipment guidelines Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation. ● When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground, wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors, use alligator clips to connect a wrist strap.
Component replacement procedures This section provides removal and replacement procedures. There are as many as 121 screws, in 12 different sizes, that must be removed, replaced, or loosened when servicing the computer. Make special note of each screw size and location during removal and replacement.
Computer feet The computer feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare part number 535793-001. There are 8 rubber feet that attach to the base enclosure in the locations illustrated below.
Battery Description Spare part number 8-cell, 63-Wh Li-on battery for use in computers with 15.6-in displays 535753-001 6-cell, 47-Wh Li-on battery for use in computers with 15.6-in displays 536418-001 6-cell, 47-Wh Li-on battery for use in computers with 14.0-in displays 572032-001 Before disassembling the computer, follow these steps: 1. Shut down the computer.
Switch cover and keyboard Description Spare part number Switch covers For use in black computers with 15.6-in displays 535861-001 For use in red computers with 15.6-in displays 572726-001 For use in black computers with 14.0-in displays 535860-001 For use in red computers with 14.0-in displays 572725-001 Keyboards for use in computers with 15.6-in displays 536537-xxx Keyboards for use in computers with 14.
2. To remove the switch cover on 15.6-in models, remove the following screws: (1) Two screw covers and two PM2.5×3.0 screws (2) Five PM2.5×3.0 broadhead screws (15.6-in models) (3) Two PM2.0×3.0 screws – or – To remove the switch cover on 14.0-in models, remove the following screws: (1) Two screw covers and two PM2.5×3.0 screws (2) Two PM2.5×3.0 broadhead screws (3) Two PM2.0×3.0 screws 3. 62 Turn the computer right-side up and open the computer as far as possible.
4. Slide the switch cover back (1), and then lift it off the computer (2). 5. On computers with 15.6-in displays, remove the two Phillips PM2.5×3.0 screws that secure the keyboard to the computer. – or – On computers with 14.0-in displays, remove the three Phillips PM2.5×3.0 screws that secure the keyboard to the computer.
6. Slide the keyboard back toward the display (1), and then rotate it forward (2) to gain access to the keyboard cable connector. 7. Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached, and disconnect the keyboard cable (2) from the system board. 8. Remove the keyboard. Reverse this procedure to install the switch cover and keyboard.
Memory module Description Spare part number 2-GB (PC2-6400, 800-MHz, DDR2) 535810-001 1-GB (PC2-6400,800-MHz, DDR2) 535809-001 Before removing the memory module, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
Optical drive NOTE: All optical drive spare part kits include an optical drive bezel. Description Spare part number DVD±RW Double-Layer Drive with LightScribe 535816-001 Blu-ray ROM DVD+/-RW SuperMulti DL Drive 535817-001 DVD-ROM Drive 535815-001 Before removing the optical drive, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
4. Remove the optical drive (3) from the computer. NOTE: 15.6-in model shown below NOTE: 14.0-in model shown below 5. If it is necessary to replace the optical drive bracket, position the optical drive with the rear toward you. 6. Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical drive.
7. Remove the optical drive bracket (2). Reverse this procedure to reassemble and install the optical drive.
Speakers Description Spare part number For use in computers with 15.6-in displays 536598-001 For use in computers with 14.0-in displays 536420-001 Before removing the speaker, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3.
WWAN module Description Spare part number WWAN module for use in all countries and regions except China 483377-002 WWAN module for use in China 571888-001 WWAN module, including GPS, UNDP (United Nations Development Program; not available with Linux) 531993-001 CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region.
4. Remove the WWAN module (3) by pulling the module away from the slot at an angle. NOTE: WWAN modules are designed with a notch (4) to prevent incorrect insertion. Reverse this procedure to install the WWAN module. Palm rest Description Spare part number Palm rest for use in black computers with 15.6-in displays (includes TouchPad) 535868-001 Palm rest for use in red computers with 15.6-in displays (includes TouchPad) 572728-001 Palm rest for use in black computers with 14.
2. On 15.6-in models: a. Remove the two Phillips PM2.5×3.0 broadhead screws (1) that secure the palm rest to the computer. b. Slide the palm rest back toward the display (2), and then lift and rotate the front edge (3) to gain access to the TouchPad cable. – or – On 14.0-in models: 72 a. Remove the three Phillips PM2.5×3.0 broadhead screws (1) that secure the palm rest to the computer. b.
3. Release the ZIF connector (1) to which the TouchPad cable is connected, and then disconnect the TouchPad cable (2) from the system board. 4. Remove the palm rest. Reverse this procedure to install the palm rest.
Hard drive NOTE: The hard drive spare part kit includes a hard drive bracket.
4. Remove the hard drive (4) from the hard drive bay. 5. If it is necessary to replace the hard drive bracket, remove the two Phillips PM3.0×4.0 hard drive bracket screws (1) from each side of the hard drive. 6. Lift the bracket (2) straight up to remove it from the hard drive. Reverse this procedure to reassemble and install the hard drive.
WLAN module Description Spare part number Broadcom 4322 802.11a/b/g/n WLAN modules: ● For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S.
Before removing the WLAN module, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 60). 5.
Display assembly on computers with 15.6-in displays NOTE: For information about removing the display from 14.0-in models, see Display assembly on computers with 14.0-in displays on page 91. NOTE: The display assembly spare part kit includes 2 WLAN antenna transceivers and cables. Description Spare part number For use only with black computers with 15.
Remove the display cables: 1. Position the computer right-side up with the front toward you. 2. Open the computer as far as possible. 3. Disconnect the display panel/webcam cable assembly (1) from the system board. 4. Remove the microphone module cable from the routing path (2), and then disconnect the cable (3) from the system board. 5. Remove the WLAN wireless antenna cables (4) from the tape, clips and routing channels built into the top cover. 6.
3. If it is necessary to replace the display bezel, display enclosure, or display hinges, remove the eight rubber screw covers (1) and the eight Phillips PM2.0×6.0 screws (2) that secure the display bezel to the display assembly. The rubber screw covers are available in the Rubber Kit, spare part number 535793-001. 4. Remove the bezel: a. Flex the top of the bezel until it disengages from the display enclosure (1). b.
5. If it is necessary to replace the webcam module from the display enclosure, gently pull the webcam module away from the double-sided tape on the display enclosure (1), disconnect the webcam cable from the module (2), and then remove the webcam. The webcam module is available using spare part number 535797-001. NOTE: To replace the webcam module in the display enclosure, align the holes on the webcam module with the pins on the display enclosure and press onto the double-sided tape. 6.
d. 7. Remove the display hinges (2). The left and right display hinges are available in the Display Hinge Kit, spare part number 535872-001 for computers with 15.6-in displays. If it is necessary to replace the display/webcam cable: NOTE: The display cable and webcam cable are bound together as one cable assembly. 82 a.
Reverse this procedure to reassemble and install the display assembly.
Top cover NOTE: The top cover removal procedures differ for 15.6-in computers from those of 14.0-in computers. NOTE: You must remove the top cover before you can remove the display assembly on computers with 14.0-in displays. You do not have to remove the top cover to remove the display assembly on computers with 15.6-in displays. Description Spare part number Top cover for use in computers with 15.6-in displays 535866-001 Top cover for use in computers with 14.
2. Disconnect the power button board cable from the system board by releasing the ZIF connector (1), and then disconnecting the cable (2). 3. Remove the 19 Phillips PM2.5×6.0 screws that secure the top cover to the computer. 4. Remove the two Phillips PM2.0×4.0 screws (1) and the three Phillips PM2.0×2.0 screws (2) that secure the top cover to the computer.
5. Lift the front edge (1) of the top cover until it disengages from the base enclosure, release the top cover from the sides and rear of the base enclosure, and then remove the top cover (2). 6. Remove the top cover. NOTE: Steps 6 through 10 illustrate how to remove the top cover from computers with 14.0-in displays. Steps 1 through 5 illustrate how to remove the top cover from computers with 15.6-in displays. 7. Position the computer right-side up with the front toward you. 8.
11. Remove the 21 PM2.5×6.0 screws that secure the top cover to the computer. NOTE: Two of these screws (one of each side) also secure the display panel to the computer. 12. Remove the Phillips PM2.0×4.5 screw that secures the top cover to the computer. 13. Lift the top cover until is disengages from the base enclosure (1). Locations at which the top cover more securely connects to the base enclosure are indicated by callout (2). 14. Remove the top cover. Reverse this procedure to install the top cover.
Power button board Description Spare part number Power button board for use in computers with 15.6-in displays (includes cable) 574513-001 Power button board for use in computers with 14.0-in displays (includes cable) 574514-001 Before removing the power button board, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2.
2. Lift the board straight up and off the top cover. NOTE: Computer with 15.6-in display shown. Reverse this procedure to install the power button board.
RTC battery Description Spare part number RTC battery 449137-001 Before removing the RTC battery, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4.
Display assembly on computers with 14.0-in displays NOTE: For information about removing the display from 15.6-in models, see Display assembly on computers with 15.6-in displays on page 78. NOTE: The display assembly spare part kit includes two WLAN antenna transceivers and cables. Description Spare part number For use only with black computers with 14.
NOTE: When replacing the display assembly, only replace the four bottom screws in the display brackets. The top screw on the bracket on each side is replaced when you install the top cover. 92 4. Lift the display assembly up and off the computer (2). 5. If it is necessary to replace the display bezel, display enclosure, or display hinges, remove the eight rubber screw covers (1) and the eight Phillips PM2.5×6.0 screws (2) that secure the display bezel to the display assembly.
e. Lift the bezel at the seam in the hinges until it disengages from the display enclosure (5). f. Remove the bezel from the display enclosure. The display bezel is available using spare part numbers 536423-001 on computers with 14.0-in displays and a webcam and 536422-001 on computers with 14.0-in displays and no webcam. 7.
94 b. Lift the bottom of the panel (2) to remove it from the enclosure. c. Remove the six Phillips PM2.0×3.0 screws (1) that secure the display hinges to the display panel. d. Remove the display hinges (2). The left and right display hinges are available in the Display Hinge Kit, spare part number 535871-001 for computers with 14.0-in displays.
9. If it is necessary to replace the webcam cable from the display enclosure, gently pull the webcam cable (1) from the clips and routing channels (2) built into the top cover. The webcam cable is included in the Display Cable Kit, spare part numbers 536430-001 for computers with 14.0-in displays. Reverse this procedure to install the display assembly.
Bluetooth module NOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetooth module cable is included in the Cable Kit, spare part number 536539-001 for computers with 15.6-in displays, 536538-001 for computers with 14.0-in displays. See Cable Kit on page 43 for more Cable Kit spare part number information.
4. Remove the Bluetooth module (3) from the base enclosure. Reverse this procedure to install the Bluetooth module. Modem module Description Spare part number For use in all countries and regions except Australia and New Zealand 510100-001 For use only in Australia and New Zealand 510100-011 Before removing the modem module, follow these steps: 1. Shut down the computer.
Remove the modem module: 1. Position the computer right-side up with the front toward you. 2. Remove the two Phillips PM2.5×3.0 screws (1) that secure the modem module to the system board. 3. Lift the modem module (2) straight up to disconnect it from the system board. 4. Remove the tape (3) that secures the cable to the modem module, and then disconnect the modem module cable (4). 5. Remove the modem module. Reverse this procedure to install the modem module.
e. Hard drive (see Hard drive on page 74) f. Display assembly (see Display assembly on computers with 15.6-in displays on page 78 or Display assembly on computers with 14.0-in displays on page 91) g. Top cover (see Top cover on page 84) Remove the USB connector assembly: 1. Position the computer right-side up with the right side toward you. 2. Disconnect the cable from the system board (1) and remove the cable from the routing path in the base enclosure (2). 3. Remove the Phillips PM2.5×3.
Heat sink and fan NOTE: The heat sink spare part kit includes replacement thermal material. Description Spare part number Heat sink for use in computers with UMA graphics subsystems 535804-001 Heat sink for use in computers with discrete graphics subsystems 535805-001 Fan 535766-001 Before removing the heat sink, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system.
4. Remove the heat sink (9). NOTE: The thermal material must be thoroughly cleaned from the surfaces of the system board (1), (2), and (3), and the heat sink components (4), (5), and (6) each time the heat sink is removed. Replacement thermal material is included with all heat sink, system board, and processor spare part kits. NOTE: Steps 5 through 8 apply to computers with UMA subsystem memory. Steps 1 through 4 apply to computers with discrete subsystem memory. 5.
8. Remove the heat sink (7). NOTE: The thermal material must be thoroughly cleaned from the surfaces of the system board (1) and (2) and the heat sink components (3) and (4) each time the heat sink is removed. Replacement thermal material is included with all heat sink, system board, and processor spare part kits.
9. If it is necessary to remove the fan from the heat sink, remove the three Phillips PM2.0×3.0 screws (1) that secure the fan to the heat sink, and then remove the fan from the heat sink (2). Reverse this procedure to install the heat sink.
Processor NOTE: The processor spare part kit includes replacement thermal material. Description Spare part number AMD Turion II Ultra Dual-Core processors (for use only with the following system boards: 585218-001, 585219-001, 585220-001, 585221-001) M500 (2.2-GHz with 1-MB L2 cache) 576253-001 M520 (2.3-GHz with 1-MB L2 cache) 583055-001 M600 (2.
4. Remove the battery (see Battery on page 60). 5. Remove the following components: a. Switch cover and keyboard (see Switch cover and keyboard on page 61) b. Optical drive (see Optical drive on page 66) c. Speakers (see Speakers on page 69) d. Palm rest (see Palm rest on page 71) e. Top cover (see Top cover on page 84) Remove the processor: 1. Position the computer right-side up with the front toward you. 2.
System board NOTE: The system board spare part kit includes replacement thermal material.
When replacing the system board, be sure that the following components are removed from the defective system board and installed on the replacement system board: ● Memory module (see Memory module on page 65) ● WLAN module (see WLAN module on page 76) ● WWAN module (see WWAN module on page 70) ● Modem module (see Modem module on page 97) ● Processor (see Processor on page 104) Remove the system board: 1. Position the computer right-side up with the front toward you. 2.
4. Remove the system board from the base enclosure (2). 5. (15.6-in models only) If it is necessary to remove the optical drive connector board from the system board, pull the optical drive connector board straight off the system board. The optical drive connector board is available using spare part number 535862-001. Reverse this procedure to install the system board. SIM Description Spare part number SIM 536599-001 Before removing the SIM, follow these steps: 1. Shut down the computer.
3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the battery (see Battery on page 60). 5. Remove the following components: a. Switch cover and keyboard (see Switch cover and keyboard on page 61) b. Optical drive (see Optical drive on page 66) c. Speakers (see Speakers on page 69) d. WWAN module (see WWAN module on page 70) e. Palm rest (see Palm rest on page 71) f.
5 Computer Setup Computer Setup in Windows Vista and Windows XP Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer. NOTE: An external keyboard or mouse connected to a USB port can be used with Computer Setup only if USB legacy support is enabled. To start Computer Setup, follow these steps: 1.
NOTE: You can use either a pointing device (TouchPad, pointing stick, or USB mouse) or the keyboard to navigate and make selections in Computer Setup. 2. Press f10 to enter BIOS Setup. 3. Select the File, Security, Diagnostics, or System Configuration menu. To exit Computer Setup menus, choose one of the following methods: ● To exit Computer Setup menus without saving your changes, click the Exit icon in the lower-left corner of the screen, and then follow the on-screen instructions.
NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File menu Select To do this System Information ● View identification information for the computer and the batteries in the system. ● View specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version. Set System Date and Time Set or change the date and time on the computer.
Security menu NOTE: Some of the menu items listed in this section may not be supported by your computer. Select To do this Setup BIOS Administrator Password Set up a BIOS administrator password. User Management (requires a BIOS administrator password) ● Create a new BIOS user account. ● View a list of ProtectTools users. Password Policy (requires a BIOS administrator password) Revise password policy criteria. HP SpareKey Enable/disable HP SpareKey (disabled by default).
Diagnostics menu Select To do this System Diagnostics Menu ● 114 Chapter 5 Computer Setup System Information—Displays the following information: ◦ Identification information for the computer and the batteries in the system. ◦ Specification information for the processor, cache and memory size, system ROM, video revision, and keyboard controller version. ● Start-up Test—Verifies the system components needed for starting the computer. ● Run-In Test—Runs a comprehensive check on system memory.
System Configuration menu NOTE: Some of the listed System Configuration options may not be supported by your computer. Select To do this Language Change the Computer Setup language. Boot Options ● Set a Startup Menu delay (in seconds). ● Enable/disable Custom Logo (disabled by default). ● Enable/disable Display Diagnostic URL (enabled by default). ● Enable/disable CD-ROM boot (enabled by default). ● Enable/disable SD Card boot (enabled by default).
Select To do this Built-In Device Options ● Enable/disable the wireless button state (enabled by default). ● Enable/disable embedded WWAN device radio (enabled by default). ● Enable/disable embedded Bluetooth® device radio (enabled by default). ● Enable/disable the Network Interface Controller (LAN) (enabled by default). ● Set the wake on LAN state.
Computer Setup in Linux Starting Computer Setup Computer Setup is a preinstalled, ROM-based utility that can be used even when the operating system is not working or will not load. NOTE: Some of the Computer Setup menu items listed in this guide may not be supported by your computer. NOTE: Pointing devices are not supported in Computer Setup. You must use the keyboard to navigate and make selections.
Using Computer Setup Navigating and selecting in Computer Setup The information and settings in Computer Setup are accessed from the File, Security, Diagnostics, and System Configuration menus. 1. Open Computer Setup by turning on or restarting the computer, and then pressing f10 while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen. Because Computer Setup is not operating system based, it does not support the TouchPad.
Computer Setup menus The menu tables in this section provide an overview of Computer Setup options. NOTE: Some of the Computer Setup menu items listed in this chapter may not be supported by your computer. File menu Select To do this System information ● View identification information for the computer. ● View specification information for the processor, cache and memory size, and system ROM. Restore Defaults DReplace the configuration settings in Computer Setup with the original factory settings.
Security menu NOTE: Some of the menu items listed in this section may not be supported by your computer. Select To do this Setup Password Enter, change, or delete a setup password. Power-On Password Enter, change, or delete a power-on password. Password Options ● Enable/disable stringent security. ● Enable/disable the password requirement on computer restart. ● Enable/disable DriveLock on any computer hard drive. ● Enter, change, or disable DriveLock on an optional MultiBay hard drive.
System Configuration menu NOTE: Some of the listed System Configuration options may not be supported by your computer. Select To do this Language Change the Computer Setup language. Boot options ● Set an f9, f10, and f12 delay when starting up. ● Enable/disable CD-ROM boot. ● Enable/disable floppy boot. ● Enable/disable internal network adapter boot. ● Enable/disable MultiBoot, which sets a boot order that can include most boot devices in the system.
Select To do this Built-in device options ● Enable/disable embedded WLAN Device Radio. ● Enable/disable embedded Bluetooth Device Radio. ● Enable/disable Network Interface Controller (NIC) ● Enable/disable LAN/WLAN Switching. ● Enable/disable Wake on LAN. ● Enable/disable the integrated camera (webcam) ● Enable/disable USB port. ● Enable/disable ExpressCard slot.
6 Specifications Computer specifications Metric U.S. Depth (14.0-in models) 23.24 cm 9.15 in Depth (15.6-in models) 24.96 cm 9.83 in Width (14.0-in models) 33.60 cm 13.2 in Width (15.6-in models) 37.18 cm 14.6 in Height (front to rear) (14.0-in models) 3.10 to 3.58 cm 1.24 to 1.41 in Height (front to rear) (15.6-in models) 3.15 to 3.63 cm 1.24 to 1.43 in Weight (14.0-in models: 6-cell battery, no WWAN, no camera, no Bluetooth, no modem, one DIMM, with ODD) < 2.27 kg < 5.
Metric Nonoperating U.S. 200 g, 2 ms, half-sine Random vibration Operating 0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate Nonoperating 1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this range of temperatures. 14.0-in WXGA display specifications Metric U.S. Height 27.94 cm 11.0 in Width 20.83 cm 8.2 in Diagonal 35.56 cm 14.
15.6-in WXGA display specifications Metric U.S. Height 20.7 cm 8.1 in Width 33.1 cm 13.0 in Diagonal 39.1 cm 15.6 in Number of colors Up to 16.8 million Contrast ratio 300:1 (typical) Brightness 200 nits (typical) Dimensions Pixel resolution Pitch 0.259 × 0.259 mm Format 1280 × 800 Configuration RGB vertical stripe Backlight CCFL Character display 80 × 25 Total power consumption 4.0 W Viewing angle +/-30° horizontal, +10/–40° vertical (typical) 15.
Hard drive specifications 500-GB* 320-GB* 250-GB* 160-GB* Height 9.5 mm 9.5 mm 9.5 mm 9.
DVD±RW Double-Layer Combo Drive specifications Applicable disc Read: Write: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CDROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CD-R, CDRW), CD-R, CD-RW, DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM CD-R and CD-RW Access time CD DVD Random < 175 ms < 230 ms Cache buffer 2 MB DVD+R, DVD+RW, DVD-R, DVDRW, DVD-RAM Data transfer rate 24X CD-ROM 3,600 KB/sec 8X D
Blu-ray ROM DVD+/-RW SuperMulti DL Drive Applicable disc Read: Write: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, MIXED MODE CD, CD-I, CD-I Bridge (Photo-CD, Video CD), Multisession CD (Photo-CD, CD-EXTRA, Portfolio, CDR, CD-RW), CD-R, CD-RW, DVDROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, HDROM (Single Layer), HD-ROM (Dual Layer), HD DVD-R, HD DVD-R for Dual Layer, HD DVD-RW, BD-ROM, BD-R, BR-RE CD-R and CD-RW DVD+R, DVD+R (9), DVD+RW, DVD-R, DVD-R (9), DVD-RW, DV
DVD-ROM Drive Applicable disc DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18, CD-ROM (Mode 1 and 2), CD Digital Audio, CD-XA ready (Mode 2, Form 1 and Form 2), CD-I (Mode 2, Form 1 and Form 2), CD-R, CD-RW, Photo CD (single and multisession), CD-Bridge Access time CD DVD Random < 100 ms < 125 ms Cache buffer 512 KB Data transfer rate CD-R (24X) 3600 KB/sec (150 KB/sec at 1X CD rate) CD-RW (10X) 1500 KB/sec (150 KB/sec at 1X CD rate) CD-ROM (24X) 3600 KB/sec (150 KB/sec at 1X CD rate) DVD (8X) 10,800
System DMA specifications, Windows Vista and XP Hardware DMA System function DMA4 Direct memory access controller System interrupt specifications, Windows Vista Hardware IRQ System function ISA0 System timer ISA1 Standard 101-/102-Key or Microsoft Natural Keyboard ISA8 System CMOS/real-time clock ISA100 - ISA119 Microsoft ACPI-Compliant System ISA12 Synaptics PS/2 TouchPad ISA120 - ISA129 Microsoft ACPI-Compliant System ISA13 Numeric data processor ISA130 - ISA139 Microsoft ACPI-Complia
Hardware IRQ System function PCI-3 Intel ICH9 Family PCI Express Root Port 2 - 2942 PCI-4 Intel ICH9 Family PCI Express Root Port 3 - 2944 PCI-5 Intel ICH9 Family PCI Express Root Port 5 - 2948 PCI-6 Intel ICH9 Family PCI Express Root Port 6 - 294A System interrupt specifications, Windows XP Hardware IRQ System function ISA0 System timer ISA1 Standard 101-/102-Key or Microsoft Natural Keyboard ISA8 System CMOS/real-time clock ISA9 Microsoft ACPI-Compliant System ISA12 Synaptics PS/2 Tou
System I/O address specifications, Windows Vista I/O address (hex) System function (shipping configuration) 000 - 01F Direct memory access controller 000 - CF7 PCI bus 020 - 021 Programmable interrupt controller 024 - 025 Programmable interrupt controller 028 - 029 Programmable interrupt controller 02C - 02D Programmable interrupt controller 02E - 02F Motherboard resources 030 - 031 Programmable interrupt controller 034 - 035 Programmable interrupt controller 038 - 039 Programmable inte
I/O address (hex) System function (shipping configuration) 0B2 - 0B3 Motherboard resources 0B4 - 0B5 Programmable interrupt controller 0B8 - 0B9 Programmable interrupt controller 0BC - 0BD Programmable interrupt controller 0C0 - 0DF Direct memory access controller 0F0 - 0F0 Numeric data processor 170 - 177 ATA Channel 1 1F0 - 1F7 ATA Channel 0 200 - 27F Motherboard resources 376 - 376 ATA Channel 1 3B0 - 3BB Mobile Intel 4 Series Express Chipset Family 3C0 - 3DF Mobile Intel 4 Serie
I/O address (hex) System function (shipping configuration) 7108 - 710F Standard Dual Channel PCI IDE Controller 7120 - 7127 Mobile Intel 4 Series Express Chipset Family 7128 - 712B Standard Dual Channel PCI IDE Controller 712C - 712F Standard Dual Channel PCI IDE Controller EF80 - EF9F Motherboard resources FE00 - FE0F Motherboard resources FE80 - FE8F Motherboard resources FFFF - FFFF Motherboard resources System I/O address specifications, Windows XP I/O address (hex) System function (s
I/O address (hex) System function (shipping configuration) 070 - 070 Motherboard resources 070 - 077 System CMOS/real time clock 080 - 080 Motherboard resources 081 - 091 Direct memory access controller 092 - 092 Motherboard resources 093 - 09F Direct memory access controller 0A0 - 0A1 Programmable interrupt controller 0A4 - 0A5 Programmable interrupt controller 0A8 - 0A9 Programmable interrupt controller 0AC - 0AD Programmable interrupt controller 0B0 - 0B1 Programmable interrupt con
I/O address (hex) System function (shipping configuration) 7020 - 703F Intel ICH9 Family USB Universal Host Controller – 2936 7040 - 705F Intel ICH9 Family USB Universal Host Controller – 2935 7060 - 707F Intel ICH9 Family USB Universal Host Controller – 2934 7080 - 709F Intel ICH9 Family USB Universal Host Controller – 2939 70A0 - 70BF Intel ICH9 Family USB Universal Host Controller – 2938 70C0 - 70DF Intel ICH9 Family USB Universal Host Controller – 2937 70E0 - 70E7 ICH9M-E/M SATA AHCI Cont
Memory address System function 98904000-989043FF Intel ICH9 Family USB2 Enhanced Host Controller – 293A 98904400-989047FF Intel ICH9 Family USB2 Enhanced Host Controller – 293C E0000000-EFFFFFFF Motherboard resources F0000000-FEDFFFFF High precision event timer FEC00000-FEC00FFF Motherboard resources FED00000-FED003FF Motherboard resources FED10000-FED13FFF Motherboard resources FED18000-FED18FFF Motherboard resources FED1C000-FED1FFFF Motherboard resources FED20000-FED3FFFF Motherboard
Memory address System function 58904000-589047FF Intel ICM9M-E/M SATA AHCI Controller 58904800-58904BFF Intel ICH9 Family USB2 Enhanced Host Controller – 293A 58904C00-58904FFF Intel ICH9 Family USB2 Enhanced Host Controller – 293C E0000000-EFFFFFFF Motherboard resources F0000000-FEDFFFFF PCI Bus FEC00000-FEC00FFF Motherboard resources FED00000-FED003FF High Precision Event Timer FED10000-FED13FFF Motherboard resources FED18000-FED18FFF Motherboard resources FED19000-FED19FFF Motherboar
7 Screw listing This chapter provides specification and reference information for the screws used in the computer. All screws listed in this section are available in the Screw Kit, spare part number 535870-001. Torx T8M2.5×6.0 screw Color Quantity Length Thread Head diameter Silver 19 6.0 mm 2.5 mm 5.0 mm Where used: 19 screws that secure the top cover to computers equipped with 15-in displays Torx T8M2.5×6.
Torx T8M2.5×4.0 screw Color Quantity Length Thread Head diameter Silver 2 4.0 mm 2.5 mm 5.
Phillips PM2.0×2.0 screw Color Quantity Length Thread Head diameter Black 3 2.0 mm 2.0 mm 5.0 mm Where used: 3 screws that secure the top cover to the computer Phillips PM2.0×2.
Phillips PM2.0×3.0 screw Color Quantity Length Thread Head diameter Silver 19 3.0 mm 2.0 mm 5.
Where used: 6 screws that secure the display hinges to the 14-in display assembly Where used: 3 screws that secure the fan to the heat sink Phillips PM2.0×3.
Phillips PM2.0×3.0 screw Color Quantity Length Thread Head diameter Black 2 3.0 mm 2.0 mm 5.
Phillips PM2.5×6.0 screw Color Quantity Length Thread Head diameter Black 15 (15-in models) or 30 (14-in models) 6.0 mm 2.5 mm 5.0 mm Where used: (1) Six screws that secure the 15-in display to the computer (2) One screw that secures the optical drive to the computer Phillips PM2.5×6.
Where used: 8 screws that secure the display bezel to the display enclosure Where used: 21 screws that secure the top cover to the base enclosure on computers with 14-in displays Phillips PM2.5×11.0 captive screw Color Quantity Length Thread Head diameter Black 1 11.0 mm 2.5 mm 5.
Phillips PM3.0×4.0 screw Color Quantity Length Thread Head diameter Silver 4 4.0 mm 3.0 mm 5.0 mm Where used: 4 screws that secure the hard drive bracket to the hard drive Phillips PM3.0×4.
Phillips PM2.0×4.0 screw Color Quantity Length Thread Head diameter Silver 4 4.0 mm 2.0 mm 5.
Phillips PM2.5×3.0 screw Color Quantity Length Thread Head diameter Black 17 (15-in models) or 18 (14-in models) 3.0 mm 2.5 mm 5.0 mm Where used: 2 screws that secure the WLAN module to the system board Phillips PM2.5×3.
Where used: 2 screws that secure the WWAN module to the system board Where used: 2 screws that secure the modem module to the system board Where used: 2 screws that secure the switch cover to the computer Where used: 2 screws that secure the keyboard to computers with 15-in displays 150 Chapter 7 Screw listing
Where used: 3 screws that secure the keyboard to computers with 14-in displays Where used: 4 screws that secure the speakers to the computer Where used: One screw that secures the USB connector assembly to the computer Phillips PM2.5×3.
Where used: 2 screws that secure the SIM to the computer 152 Chapter 7 Screw listing
Phillips PM2.5×4.5 screw Color Quantity Length Thread Head diameter Black 4 (15-in models) or 4.5 mm 2.5 mm 5.0 mm 7 (14-in models) Where used: 4 screws that secure the display assembly to computers with 14-in displays Where used: 4 screws that secure the display panel to the 15-in display enclosure Phillips PM2.5×4.
Where used: 2 screws that secure the display bezel to the 14-in display enclosure Where used: One screw in the right rear that secures the top cover to computers with 14-in displays 154 Chapter 7 Screw listing
Phillips PM2.5×3.0 broadhead screw Color Quantity Length Thread Head diameter Black 9 (15-in models) or 3.0 mm 2.5 mm 7.0 mm 5 (14-in models) Where used: 2 screws that secure the system board to computers with 15-in displays Where used: 3 screws that secure the system board to computers with 14-in displays Phillips PM2.5×3.
Where used: 5 screws that secure the switch cover to computers with 15-in displays Where used: 2 screws that secure the switch cover and power button board to the computer 156 Chapter 7 Screw listing
Phillips PM2.5×7.0 screw Color Quantity Length Thread Head diameter Black 1 7.0 mm 2.5 mm 5.0 mm Where used: One screw that secures the USB connector assembly to the computer Phillips PM2.5×7.
Phillips PM2.5×9.0 captive screw Color Quantity Length Thread Head diameter Silver 7 (discrete) or 5 (UMA) 9.0 mm 2.5 mm 5.
Where used: 5 screws that secure the heat sink to the system board for computers with UMA memory Phillips PM2.5×9.
8 Backup and recovery Backup and recovery in Windows Vista Overview To protect your information, use the Backup and Restore Center to back up individual files and folders, back up your entire hard drive (select models only), or create system restore points. In case of system failure, you can use the backup files to restore the contents of your computer.
To create a screen shot: 1. Display the screen you want to save. 2. Copy the screen image: To copy only the active window, press alt+fn+prt sc. To copy the entire screen, press fn+prt sc. 3. Open a word-processing document, and then select Edit > Paste. The screen image is added to the document. 4. ● Save the document. When backing up to discs, use any of the following types of discs (purchased separately): CD-R, CD-RW, DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW.
Using the Windows recovery tools To recover information you previously backed up, follow these steps: 1. Click Start > All Programs > Maintenance > Backup and Restore Center. 2. Follow the on-screen instructions to recover your entire computer (select models only) or your files. NOTE: Windows includes the User Account Control feature to improve the security of your computer.
4. Press f11 while the “Press for recovery” message is displayed on the screen. 5. Follow the on-screen instructions. Using a Windows Vista operating system DVD (purchased separately) If you are unable to boot (start up) your computer, you must purchase a Windows Vista operating system DVD to reboot the computer and repair the operating system. Make sure that your most recent backup (stored on discs or on an external drive) is easily accessible.
Backup and recovery in Windows XP Overview To protect your information, use the Windows® Backup utility (select models only) to back up files and folders or create recovery points. In case of system failure, you can use the backup files to restore your computer.
NOTE: Be sure that the computer is connected to AC power before you start the backup process. NOTE: The backup process may take over an hour, depending on file size and the speed of the computer. 1. Click Start > All Programs > Accessories > System Tools > Backup. 2. Follow the on-screen instructions.
9 Connector pin assignments Audio-in (microphone) Pin Signal 1 Audio signal in 2 Audio signal in 3 Ground Audio-out (headphone) Pin Signal 1 Audio out, left channel 2 Audio out, right channel 3 Ground 166 Chapter 9 Connector pin assignments
External monitor Pin Signal 1 Red analog 2 Green analog 3 Blue analog 4 Not connected 5 Ground 6 Ground analog 7 Ground analog 8 Ground analog 9 +5 VDC 10 Ground 11 Monitor detect 12 DDC 2B data 13 Horizontal sync 14 Vertical sync 15 DDC 2B clock External monitor 167
RJ-11 (modem) Pin Signal 1 Unused 2 Tip 3 Ring 4 Unused 5 Unused 6 Unused 168 Chapter 9 Connector pin assignments
RJ-45 (network) Pin Signal 1 Transmit + 2 Transmit - 3 Receive + 4 Unused 5 Unused 6 Receive - 7 Unused 8 Unused Universal Serial Bus Pin Signal 1 +5 VDC 2 Data - 3 Data + 4 Ground RJ-45 (network) 169
10 Power cord set requirements The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120 volts AC or from 220 to 240 volts AC. The 3-conductor power cord set included with the computer meets the requirements for use in the country or region where the equipment is purchased. Power cord sets for use in other countries and regions must meet the requirements of the country or region where the computer is used.
Requirements for specific countries and regions Country/region Accredited agency Applicable note number Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan METI 3 The Netherlands KEMA 1 Norway NEMKO 1 The People's Republic of China CCC 5 South Korea EK 4 Sweden SEMKO 1 Switzerland SEV 1 Taiwan BSMI 4 The United Kingdom BSI 1 The United States UL 2 1.
11 Recycling Battery When a battery has reached the end of its useful life, do not dispose of the battery in general household waste. Follow the local laws and regulations in your area for computer battery disposal. Display WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. CAUTION: The procedures in this chapter can result in damage to display components.
Perform the following steps to disassemble the display assembly: 1. Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly. 2. Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the display bezel until the bezel disengages from the display assembly. 3. Remove the display bezel (3).
4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2). 5. Remove all screws (1) that secure the display panel assembly to the display enclosure. 6. Remove the display panel assembly (2) from the display enclosure. 7. Turn the display panel assembly upside-down. 8. Remove all screws that secure the display panel frame to the display panel. 9. Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display panel frame.
10. Remove the display panel frame (2) from the display panel. 11. Remove the screws (1) that secure the backlight cover to the display panel. 12. Lift the top edge of the backlight cover (2) and swing it outward. 13. Remove the backlight cover. 14. Turn the display panel right-side up.
15. Remove the backlight cables (1) from the clip (2) in the display panel. 16. Turn the display panel upside-down. WARNING! The backlight contains mercury. Exercise caution when removing and handling the backlight to avoid damaging this component and causing exposure to the mercury. 17. Remove the backlight frame from the display panel.
18. Remove the backlight from the backlight frame. 19. Disconnect the display panel cable (1) from the LCD panel. 20. Remove the screws (2) that secure the LCD panel to the display rear panel. 21. Release the LCD panel (3) from the display rear panel. 22. Release the tape (4) that secures the LCD panel to the display rear panel. 23. Remove the LCD panel. 24. Recycle the LCD panel and backlight.
Index A AC adapter identifying 20, 32 spare part numbers 45, 46, 47 antenna, disconnecting 70, 77 applications key, Windows 14, 15 audio, product description 4 audio-in (microphone) jack identifying 16, 27 pin assignments 166 audio-out (headphone) jack identifying 16, 27 pin assignments 166 B backing up Windows Vista 160 Windows XP 164 Backup and Restore Center 160, 161 base enclosure, spare part number 39, 48 battery identifying 32, 60 removal 60 spare part number 39, 48, 50, 60 battery bay 19, 30 battery
display assembly removal 78, iii spare part numbers 34, 35, 50, 51, 78, iii display bezel removal 80, 92 spare part number 40, 49, 80, 93 Display Cable Kit, spare part number 41, 49 display cable, spare part number 49 display component recycling 172 display enclosure spare part numbers 49 display enclosure, spare part number 41, 50 Display Hinge Kit, spare part number 40, 48, 82, 94 display panel removal 81, 94 spare part numbers 51 display specifications 124, 125 drive light, identifying 16, 27 DriveLock a
lights battery 17, 28 caps lock 12, 23 drive 16, 27 Info 12 Info Center/QuickLook 23 optical drive 17, 28 power 12, 23 QuickLook 12 QuickLook/Info Center 23 webcam 10, 21 wireless 16, 27 M mass storage devices, spare part numbers iii Media Card Reader, identifying 16, 27 memory map specifications Windows Vista 136 Windows XP 137 memory module product description 3 removal 65 spare part numbers 38, 48, 65 microphone (audio-in) jack identifying 16, 27 pin assignments 166 model name 1 modem jack, pin assignmen
R recovery partition 162 release latches, battery 19, 30 removal/replacement preliminaries 53 procedures 58 restore security defaults 116 restore the factory settings 112 restoring the hard drive 162 RJ-11 (modem) cable, illustrated 43 RJ-11 (modem) jack identifying 17, 28 pin assignments 168 RJ-45 (network) cable, illustrated 43 RJ-45 (network) jack identifying 18, 29 pin assignments 169 RTC battery removal 90 spare part number 38, 46, 90 Rubber Kit, spare part number 39, 47 run-in test 114 S SATA (Serial
USB legacy support 110, 115, 117, 121 USB port identifying 17, 18, 28, 29 pin assignments 169 V vents, identifying 18, 29 Virtualization Technology 115 W webcam identifying 10, 21 removing 81, 93 spare part number 41, 47, 81, 93 webcam light, identifying 10, 21 Windows applications key, identifying 14, 15 Windows Backup utility 164, 165 Windows logo key, identifying 14, 15 Windows recovery 161, 165 Windows Vista operating system DVD 163 wireless antenna, disconnecting 70, 77 wireless light, identifying 16,
