ProLiant 1600 Servers Supporting Pentium II Processors with 100 MHz GTL Bus Maintenance and Service Guide First Edition (May 1998) Part Number 179480-001 Spares Part Number 313625-001 Compaq Computer Corporation
Notice The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
iii Contents About This Guide Compaq Technician Notes................................................................................................... vii Where to Go for Additional Help ....................................................................................... viii Other Information Sources........................................................................................... viii Integrated Management Display .............................................................................
iv Chapter 3 Diagnostic Tools Utilities Access .................................................................................................................. 3-2 Power-On Self-Test (POST) ............................................................................................... 3-4 Diagnostics Software........................................................................................................ 3-19 Running Diagnostics......................................................................
v Chapter 4 Connectors, Switches, and Jumpers Processor Board ................................................................................................................. 4-2 Components ................................................................................................................ 4-2 External Connectors and LEDs.................................................................................... 4-3 Bus Settings..........................................................................
vii About This Guide This Maintenance and Service Guide is a troubleshooting guide that can be used for reference when servicing ProLiant 1600 Servers Supporting Pentium II Processors with 100 MHz GTL Bus. WARNING: To reduce the risk of personal injury from electrical shock and hazardous energy levels, only authorized service technicians should attempt to repair this equipment. Improper repairs could create conditions that are hazardous.
viii About This Guide ■ ■ Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. CAUTION: To properly ventilate your system, you must provide at least 12 inches (30.5 cm) of clearance at the front and back of the computer. IMPORTANT: Any indication of repair at the component level or modification of a printed wiring board may void any warranty.
ix http://www.compaq.com.
1-1 Chapter 1 Illustrated Parts Catalog This chapter provides the illustrated parts breakdown and a spare parts list for the Compaq ProLiant 1600 Servers Supporting Pentium II Processors with 100 MHz GTL Bus. See Table 1-1 for the names of referenced spare parts. Mechanical Parts Exploded View 3 10 15 1 8 14 4 11 32a 2 5 6 Figure 1-1.
1-2 Illustrated Parts Catalog System Components Exploded View 9 7 15 1 14 19 20 17 14 6 32b 16 18 12 13 Figure 1-2.
1-3 Spare Parts List Table 1-1 Spare Parts List Ref CHASSIS Description Spare Part # 1 Chassis 313641-001 2 Right Side Access Panel 271927-001 3 Left Side Access Panel and Top Cover 333563-001 4 Front Bezel 298012-001 5 Front Bezel Plate (rack-mountable model only) 271924-001 6 Hot-Plug Drive Cage, (5 x 1.0-inch) 250911-001 SYSTEM COMPONENTS 7 Power Supply, 325W 271916-001 8 I/O Fan with Bracket 281844-001 9 4.
1-4 Illustrated Parts Catalog Spare Parts List Continued 24 SCSI DAT/DLT Cable 300926-001 * 25 Parallel Cable 271938-001 * 26 SCSI Adapter Kit 50-to-68, Female 189638-001 * MISCELLANEOUS 27 Return Kit 298017-001 * 28 Carton and Buns (International) 298017-002 * 29 Maintenance and Service Guide 313625-001 * 30 Illustrated Parts Map 313626-001 * 31 Slide Rail, 22-inch, Pair 165689-002 * 32 Miscellaneous Plastics Kit a) feet b) processor retention brackets 333575-001 33 Country Kit
1-5 Spare Parts List Continued 50 2.1-GB Pluggable Wide Ultra 1-inch Hard Drive 242603-001 * 51 2.1-GB Non-Pluggable Wide Ultra 1-inch Hard Drive 242604-001 * 52 2.1-GB Pluggable Fast-Wide SCSI-2 1-inch Hard Drive 199878-001 * 53 2.1-GB Pluggable Fast-Wide SCSI-2 Hard Drive 199643-001 * 54 2.1-GB Non-Pluggable Fast-Wide SCSI-2 Hard Drive 199644-001 * 55 2.1-GB Pluggable Fast-Wide SCSI-2 Hard Drive 199428-001 * 56 2.1-GB Non-Pluggable Fast-SCSI-2 Hard Drive 142272-001 * 57 1.
2-1 Chapter 2 Removal and Replacement Procedures This chapter provides subassembly/module-level removal and replacement procedures for the ProLiant 1600 Servers Supporting Pentium II Processors with 100 MHz GTL Bus. After completing all necessary removal and replacement procedures, run the Diagnostics program to verify that all components operate properly.
2-2 Removal and Replacement Procedures Symbols in Equipment WARNING: Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, allow the surface to cool before touching. WARNING: Any surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards.
2-3 CAUTION: Electrostatic discharge can damage electronic components. Be sure you are properly grounded before beginning any installation procedure. See the section titled “Electrostatic Discharge Information” in this chapter, for more information.
2-4 Removal and Replacement Procedures Rack Warnings WARNING: To reduce the risk of personal injury, make sure that the rack is adequately stabilized before extending a component outside the rack. A rack may become unstable if more than one component is extended for any reason. Extend only one component at a time. WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: ■ The leveling jacks are extended to the floor.
2-5 Server Warnings and Precautions WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching. WARNING: To reduce the risk of electric shock or damage to the equipment: Do not disable the power cord grounding plug. The grounding ■ plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet ■ that is easily accessible at all times.
2-6 Removal and Replacement Procedures Front Bezel To remove the front bezel: 1. Unlock the front bezel keylock. 2. Open the front bezel. 3. Lift up the front bezel and pull it away from the chassis. Figure 2-1. Removing the front bezel Reverse steps 1 through 3 to replace the front bezel.
2-7 Front Bezel Plate To remove the front bezel plate : NOTE: This procedure applies to the ProLiant 1600 rack-mountable model only. 1. Remove the ten T-15 screws from the front bezel plate. 2. Remove the front bezel plate. Figure 2-2. Removing the front bezel plate Reverse steps 1 through 2 to replace the front bezel.
2-8 Removal and Replacement Procedures Feet To remove the feet from the chassis, one at a time: 1. Perform the preparation procedures. See page 2-2. 2. Remove the front bezel. See page 2-6. 3. Place the server on its left side. 4. Remove the T-15 screw from each foot 1. 5. Pivot each foot down 2, and pull it off the base of the chassis 3. 3 2 1 Figure 2-3. Removing the feet from the chassis Reverse steps 1 through 5 to replace the feet. Make sure each foot snaps securely in its position.
2-9 Left Side Access Panel Remove the left side access panel to service the hot-plug drive cage, IDE 24X CD-ROM drive, power supply, and backplane board. To remove the left side access panel: WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. 1. Perform the preparation procedures. See page 2-2. 2. Open the front bezel. 3. Loosen the two thumbscrews attaching the left side access panel to the front of the chassis. 4.
2-10 Removal and Replacement Procedures Top Cover Remove the top cover to service the PCI and ISA boards, system switches, IDE CD-ROM drive cables, diskette drive cables, I/O fan with bracket, and the power switch. WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. To remove the top cover: 1. Perform the preparation procedures. See page 2-2. 2. Open the front bezel. 3.
2-11 Right Side Access Panel Remove the right side access panel to convert from tower to rack or to replace a damaged panel. To remove the right side access panel: 1. Perform the preparation procedures. See page 2-2. 2. Remove the front bezel. See page 2-6. 3. Remove the feet on the base of the right side access panel (tower model). See page 2-8. 4. Remove the two T-15 screws securing the right side access panel to the front of the chassis. 5.
2-12 Removal and Replacement Procedures Mass Storage Compaq ProLiant 1600 servers ship standard with a hot-pluggable drive cage containing five 1-inch hot-pluggable drive bays. Four removable media bays contain one-third height diskette drive and one-half-height IDE CD-ROM drive. Two bays can contain a second CD-ROM drive, tape drives, hard drives, or any SCSI device. The Compaq ProLiant 1600 servers support up to seven mass storage devices.
2-13 Hot-Plug Drive Cage To remove the hot-plug drive cage: 1. Perform the preparation procedures. See page 2-2. 2. Remove the front bezel. See page 2-6. 3. Remove the left side access panel. See page 2-9. 4. Disconnect all cables from the hot-plug drive cage. 5. Remove the four T-15 screws. 6. Slide the hot-plug drive cage out the front of the chassis. Figure 2-8.
2-14 Removal and Replacement Procedures IDE 24X CD-ROM Drive To remove the IDE 24X CD-ROM drive: 1. Perform the preparation procedures. See page 2-2. 2. Open the front bezel. 3. Remove the left side access panel. See page 2-9. 4. Remove the two T-15 screws and washers from the front of the drive. 5. Disconnect the CD-ROM signal cable. 6. Slide the CD-ROM drive out the front of the chassis. 7. Disconnect the power cable. Figure 2-9.
2-15 Diskette Drive To remove the 1.44 MB diskette drive: 1. Perform the preparation procedures. See page 2-2. 2. Remove the front bezel. See page 2-6. 3. Remove the top cover. See page 2-10. 4. Disconnect all cables from the diskette drive. 5. Remove the two T-15 screws and washers from the front of the drive. 6. Slide the diskette drive out the front of the chassis. Figure 2-10. Removing the 1.44 MB diskette drive Reverse steps 1 through 6 to replace the 1.44 MB diskette drive.
2-16 Removal and Replacement Procedures Cable Diagrams Spare Part No. 271936-002 Figure 2-11. IDE 24X CD-ROM drive cable Spare Part No. 271928-001 Figure 2-12.
2-17 Spare Part No. 149097-001 Figure 2-13.
2-18 Removal and Replacement Procedures System I/O Board Cage The system I/O board cage contains the system I/O board with PCI slots, system switches, ISA slots, and the battery. Four slots are PCI/ISA; two are PCI only, for a total of six slots. To remove the system I/O board cage: 1. Perform the preparation procedures. See page 2-2. 2. Remove the top cover. See page 2-10. 3. Disconnect all cables from the system I/O board cage and any installed boards. 4. Remove any installed boards.
2-19 I/O Fan with Bracket To remove the I/O fan with bracket: 1. Perform the preparation procedures. See page 2-2. 2. Remove the top cover. See page 2-10. 3. Loosen the single thumbscrew attaching the I/O fan with bracket to the chassis 1. 4. Tilt the top of the I/O fan with bracket forward and away from the chassis 2. 5. Disconnect the I/O fan with bracket cable and slide it out of the clip 3. 6. Lift the I/O fan with bracket away from the chassis. 1 2 3 Figure 2-15.
2-20 Removal and Replacement Procedures Power Switch To remove the power switch and cable assembly: WARNING: Any surface or area of the equipment marked with these symbols indicates the presence of electrical shock hazards. The enclosed area contains no operatorserviceable parts. To reduce the risk of injury from electrical shock hazards, do not open this enclosure. 1. Perform the preparation procedures. See page 2-2. 2. Remove the front bezel. See page 2-6. 3. Remove the top cover. See page 2-10.
2-21 6. Unwind the power supply cables and LED cables from the strain-relief casing and disconnect them from the power switch. Power SCSI Activity Figure 2-17. Disconnecting the power switch cables Reverse steps 1 through 6 to replace the power switch and cable assembly.
2-22 Removal and Replacement Procedures Processor Cage Assembly The processor cage assembly contains the processor cage, processor board, processor, processor power module, and memory. See Chapter 1, “Illustrated Parts Catalog,” for the spare part numbers for these items. Processor Cage To remove the processor cage: 1. Perform the preparation procedures. See page 2-2. 2. Disconnect all cables from the rear exterior of the processor cage. 3. Remove the security screw (if installed) 1. 4.
2-23 5. Pull the processor cage out through the back of the chassis. Figure 2-19. Removing the processor cage Reverse steps 1 through 5 to replace the processor cage. NOTE: Replace the spare parts into the same slots and sockets from which they were removed in the system I/O board cage.
2-24 Removal and Replacement Procedures Processor To remove the processor: 1. Perform the preparation procedures. See page 2-2. 2. Remove the processor cage (see page 2-22) and open the cage door. 3. Push in the latches on each side of the processor until you hear two clicks 1. This locks the tabs in the open position. 4. Lift the processor from the processor cage 2. 1 2 1 Figure 2-20. Removing the processor Reverse steps 1 through 4 to replace the processor.
2-25 Processor Retention Bracket To remove the processor retention bracket: 1. Perform the preparation procedures. See page 2-2. 2. Remove the processor cage (see page 2-22) and open the cage door. 3. Lift the processor from the processor cage. See page 2-24. 4. Remove the two security screws, 1 and lift the processor retention bracket from the processor board and cage 2. 1 2 1 Figure 2-21. Removing the processor retention bracket.
2-26 Removal and Replacement Procedures Processor Power Module To remove the processor power module: 1. Perform the preparation procedures. See page 2-2. 2. Remove the processor cage (see page 2-22) and open the cage door. 3. Pull out the clips on each end of the processor power module 1. 4. Lift the processor power module from the processor cage 2. 1 2 Figure 2-22.
2-27 Memory Compaq ProLiant 1600 servers ship standard with 64 MB of memory installed on the processor board in socket 4. Memory is expandable to 1GB. 4 3 2 1 Figure 2-23.
2-28 Removal and Replacement Procedures The following guidelines MUST be followed when installing or replacing memory: Use 100 MHz, 32-, 64-,128-, or 256-MB; registered SDRAM DIMMs. CAUTION: Use only Compaq SDRAM DIMMs. SDRAM DIMMs from other sources may adversely affect data integrity. Power-On Self-Test (POST) will warn of non-supported SDRAM DIMMs. To remove a SDRAM DIMM: 1. Perform the preparation procedures. See page 2-2. 2. Remove the processor cage and place it on a non-conductive work surface.
2-29 Power Supply To remove the power supply: 1. Perform the preparation procedures. See page 2-2. 2. Remove the left side access panel. See page 2-9. 3. Remove the processor cage. See page 2-22. 4. Slide the hot-pluggable drive cage out slightly 1. See Figure 2-8 to determine which screws should be removed. 5. Remove the air baffle by detaching the hook-and-loop fastener holding it to the power supply. 6. Disconnect the power supply cable from the power switch. See Figure 2-17 on page 220. 7.
2-30 Removal and Replacement Procedures When reconnecting the cables from the power supply to the backplane board, match cables P1, P2, and P5 with the appropriate connectors. Cable P5 should plug into the far left side of connector P5. Figure 2-26 depicts the positions of these cable connectors on the backplane board. P2 P1 P5 Figure 2-26.
2-31 Backplane Board To remove the backplane board: 1. Perform the preparation procedures. See page 2-2. 2. Remove the top cover. See page 2-10. 3. Remove the left side access panel. See page 2-9. 4. Remove the system I/O board cage. See page 2-18. 5. Remove the processor cage. See page 2-22. 6. Disconnect all cables from the backplane board. 7. Remove the three T-15 screws from the backplane board. 8. Slide the backplane board down slightly and pull it from its mounting posts. Figure 2-27.
2-32 Removal and Replacement Procedures External Replacement Battery CAUTION: Do not remove the lithium battery from the system I/O board or permanent damage may occur. If the battery fails, use the external replacement battery. To install the external replacement battery: 1. Perform the preparation procedures. See page 2-2. 2. Remove the top cover. See page 2-10. 3. Connect the replacement battery to the battery header on the system I/O board. 4.
3-1 Chapter 3 Diagnostic Tools This chapter describes software and firmware diagnostic tools available for all Compaq server products.
3-2 Diagnostic Tools Utilities Access The Compaq SmartStart and Support Software CD contains the SmartStart program and many of the Compaq utilities needed to maintain your system, including: ■ System Configuration Utility ■ Array Configuration Utility ■ Drive Array Advanced Diagnostics Utility ■ ROMPaq Firmware Upgrade Utilities CAUTION: Do not select the Erase Utility when running the SmartStart and Support Software CD. This will result in data loss to the entire system.
3-3 ■ Run the utilities from diskette. You can also run the utilities from their individual diskettes. If you have a utility diskette newer than the version on the SmartStart and Support Software CD, use that diskette. You can also create a diskette version of the utility from the SmartStart and Support Software CD. To create diskette versions of the utilities from the CD: 1. Boot the Compaq SmartStart and Support Software CD. 2.
3-4 Diagnostic Tools Power-On Self-Test (POST) POST is a series of diagnostic tests that runs automatically on Compaq computers when the system is turned on. POST checks the following assemblies to ensure that the computer system is functioning properly: ■ Keyboard ■ Power supply ■ System board ■ Memory ■ Memory expansion boards ■ Controllers ■ Diskette drives ■ Hard drives If POST finds an error in the system, an error condition is indicated by an audible and/or visual message.
3-5 POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem Action 163-Time & Date Not Set 2S Invalid time or date in configuration memory. Run the System Configuration Utility and correct. 164-Memory Size Error 2S Configuration memory incorrect. Run the System Configuration Utility and correct. 170- Expansion Device Not Responding None EISA or PCI expansion board failure. Check board for secure installation. Replace the failed board if necessary.
3-6 Diagnostic Tools 178-Processor Configuration Invalid None Processor type or step does not match configuration memory. Run the System Configuration Utility and correct. 179-System Revision Mismatch None A board was installed that has a different revision date. Run the System Configuration Utility and correct.
3-7 POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem Action 180-Log Reinitialized None 201-Memory Error None RAM failure. Run Diagnostics. Replace failed assembly as indicated. 203-Memory Address Error None RAM failure. Run Diagnostics. Replace failed assembly as indicated. 205-Cache Memory Error None Cache memory error. Replace the processor board in the slot indicated. 205-Option Cache Memory Error None Option cache memory error.
3-8 Diagnostic Tools 212-System Processor Failed/Mapped out 1S 213-Cache Size Error None Processor in slot x failed. Run Diagnostics and replace failed processor. Invalid optional cache size. Replace cache with 256K cache.
3-9 POST Error Messages Continued Error Code 213-System Processor Not Installed Audible Beeps L=Long S=Short 1S Probable Source of Problem Action System processor configured for slot indicated is missing. Install processor in the slot indicated or run the System Configuration Utility to remove the processor from the .CFG file. 214-DC-DC Converter Failed None PowerSafe Module (DCDC Converter) failed. Run Diagnostics. Replace failed assembly as indicated. 301-Keyboard Error None Keyboard failure.
3-10 Diagnostic Tools 601-Diskette Controller Error None Diskette controller circuitry failure. 1. Make sure the diskette drive cables are attached. 2. Replace the diskette drive and/or cable. 3. Replace the system board.
3-11 POST Error Messages Continued Error Code 605-Diskette Drive Type Error Audible Beeps L=Long S=Short 2S Probable Source of Problem Action Mismatch in drive type. Run the System Configuration Utility to set diskette type correctly. Installed coprocessor not configured. Run the System Configuration Utility and correct. Coprocessor or configuration error. 1. Run the System Configuration Utility and correct.
3-12 Diagnostic Tools 1612-Primary power supply failure 2S 1613-Low System Battery None 1614-Redundant fan failure detected None Primary power supply has failed. Replace power supply as soon as possible. Real time clock system battery is running low on power. Run Diagnostics. Replace failed assembly as indicated.
3-13 POST Error Messages Continued Audible Beeps L=Long S=Short Probable Source of Problem 1615- Power Supply Failure in Bay X None A power supply has failed. Replace or check specified power supply. 1616- Power Supply Configuration Error 2L, 2S Single power supply system is installed in Bay 2 and not in Bay 1. Move power supply from Bay 2 to Bay 1. 1701-SCSI Controller failure None A test on the Fast SCSI-2 Controller failed Run Diagnostics. Replace failed assembly as indicated.
3-14 Diagnostic Tools POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem Action 1705-Locked SCSI Bus Detected. System halted. None SCSI bus failure. Run Diagnostics. Replace failed assembly as indicated. 1730-Fixed Disk 0 does not support DMA Mode. None Fixed disk drive error. Run the System Configuration Utility and correct. 1731-Fixed Disk 1 does not support DMA Mode. None Fixed disk drive error.
3-15 POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem 1764-Slot x Drive Array - Capacity Expansion Process is temporarily disabled (followed by one of the following): Expansion will resume when Array Accelerator has been reattached. Expansion will resume when Array Accelerator has been replaced. Action Reattach or replace Array Accelerator, wait until the Array Accelerator batteries have charged, or for Automatic Data Recovery to complete, as indicated.
3-16 Diagnostic Tools POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem Action 1769-Slot x Drive Array - Drive(s) disabled due to failure during expand. Select F1 to continue with logical drives disabled. Select F2 to accept data loss and to re-enable logical drives. None SMART-2 Controller error. Data has been lost while expanding the array, therefore the drives have been temporarily disabled.
3-17 1776-Drive Array - SCSI Port Termination Error None External and internal SCSI drives are both configured to Port 1. Reconfigure drives.
3-18 Diagnostic Tools POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem Action 1777-Drive Array External Drive Subsystem Error None Cooling fan failure, internal temperature alert or open side panel. Inspect for cooling fan failure or open side panel. 1778-Drive Array resuming Automatic Data Recovery process None This message appears whenever a controller reset or power cycle occurs while Automatic Data Recovery is in progress. No action necessary.
3-19 POST Error Messages Continued Error Code 1786-Drive Array Recovery Needed Audible Beeps L=Long S=Short None Probable Source of Problem Interim Data Recovery mode. Data has not been recovered yet. The following drive(s) need Automatic Data Recovery: Drive X. Physical drive replacement needed: Drive X Press F1 key to allow Automatic Data Recovery to begin. Data will automatically be restored to drive X now that the drive has been replaced or now seems to be working.
3-20 Diagnostic Tools POST Error Messages Continued Error Code *1788-Incorrect Drive Replaced: Drive X Drive(s) were incorrectly replaced: Drive Y Select "F1" to continue - drive array will remain disabled. Select "F2" to reset configuration - all data will be lost. Audible Beeps L=Long S=Short None Probable Source of Problem Drives are not installed in their original positions, so the drives have been disabled. See note below. Action Reinstall the drives correctly as indicated.
3-21 POST Error Messages Continued Error Code Audible Beeps L=Long S=Short Probable Source of Problem Action 1790-Disk 0 Configuration Error None Hard drive error or wrong drive type Run the System Configuration Utility and Diagnostics and correct. 1791-Disk 1 Error None Hard drive error or wrong drive type. Run the System Configuration Utility and Diagnostics and correct. 1792-Drive Array Reports Valid Data Found in Array Accelerator.
3-22 Diagnostic Tools POST Error Messages Continued Error Code 1795-Drive Array - Array Accelerator Configuration Error. Audible Beeps L=Long S=Short None Data does not correspond to this drive array. Array Accelerator is temporarily disabled. 1796-Drive Array - Array Accelerator Not Responding. Probable Source of Problem This indicates that while the system was in use, power was interrupted while data was in the Array Accelerator memory.
3-23 POST Error Messages Continued Error Code 1798-Drive Array - Array Accelerator Write Error Occurred. Audible Beeps L=Long S=Short Probable Source of Problem Action None Hard parity error while writing data to postedwrites memory. Enable Array Accelerator. 1799-Drive Array - Drive(s) Disabled due to Array Accelerator Data Loss.Select "F1" to continue with logical drives disabled. Select "F2" to accept data loss and to re-enable logical drives.
3-24 Diagnostic Tools Diagnostics Software Tables 3-2 through 3-20 include all test error codes generated by Compaq products. Each code has a corresponding description and recommended action(s). Your system generates only those codes that are applicable to your configuration and options. When you select Diagnostics and Utilities from the System Configuration Utility main menu, the utility prompts you to test, inspect, upgrade, and diagnose the server.
3-25 7. Install a loopback plug (Part Number 142054-001), when required by Diagnostics. 8. Run the latest version of Diagnostics. Running Diagnostics There are two ways to access the utilities: ■ From the System Partition. ■ From diskette. A diskette can be created from the SmartStart CD. 1. Accessing the utilities from the system partition: 2. Reboot the server by pressing the Ctrl+Alt+Delete keys. Press F10 when the following prompt appears at the top of the screen during POST.
3-26 Diagnostic Tools Primary Processor Test Error Codes The 100 series of Diagnostic error codes identifies failures with processor and system board functions. Corrective action may require replacement of system boards or processor assemblies (either processor boards or system boards that include the processor). Table 3-2 Primary Processor Test Error Codes Error Code 101-xx Description CPU test failed 104-xx 105-xx 106-xx DMA page registers test failed. Interrupt controller master test failed.
3-27 199-xx Installed devices test failed. 1. Check the system configuration and retest. 2. Verify cable connections and retest. 3. Check switch and/or jumper settings and retest. 4. Run the Configuration utility and retest. 5. Replace the processor board and retest. 6. Replace the system board and retest.
3-28 Diagnostic Tools Memory Test Error Codes The 200 series of Diagnostic error codes identifies failures with the memory subsystem. Corrective action may require replacement of the memory expansion board, the memory modules, or the processor assembly. Table 3-3 Memory Test Error Codes Error Code Description 200-xx Invalid memory configuration. Recommended Action Reinsert memory modules in correct location and retest. 201-xx 202-xx Memory machine ID test failed. Memory system ROM checksum failed.
3-29 Keyboard Test Error Codes The 300 series of Diagnostic error codes identifies failures with keyboard and system board functions. Corrective action may require replacement of a keyboard or the system board assembly. Table 3-4 Keyboard Test Error Codes Error Code 301-xx 302-xx 303-xx 304-xx Description Keyboard short test, 8042 self-test failed. Keyboard long test failed. Keyboard LED test, 8042 self-test failed. Keyboard typematic test failed.
3-30 Diagnostic Tools Video Display Unit Test Error Codes The 500 series of Diagnostic error codes identifies failures with video or system board functions. Corrective action may require replacement of a video board or the system board assembly. Table 3-6 Video Display Unit Test Error Codes Error Code 501-xx 502-xx 503-xx 504-xx 505-xx 506-xx 507-xx 508-xx 509-xx 510-xx 511-xx 512-xx 514-xx 516-xx Description Video controller test failed. Video memory test failed. Video attribute test failed.
3-31 Diskette Drive Test Error Codes The 600 series of Diagnostic error codes identifies failures with diskette, diskette drive, or system board functions. Corrective action may require replacement of a diskette, a diskette drive, or the system board assembly. Table 3-7 Diskette Drive Test Error Codes Error Code 600-xx 601-xx 602-xx 603-xx 604-xx 605-xx 606-xx 607-xx 608-xx 609-xx 610-xx 694-xx 697-xx 698-xx 699-xx Description Diskette ID drive types test failed. Diskette format failed.
3-32 Diagnostic Tools Serial Test Error Codes The 1100 series of Diagnostic error codes identifies failures with serial/parallel interface board or system board functions. Corrective action may require replacement of the serial/parallel interface board or the system board assembly. Table 3-9 Serial Test Error Codes Error Code Description 1101-xx Serial port test failed. 1109-xx Clock register test failed. Recommended Action The following steps apply to error codes 1101-xx and 1109-xx: 1.
3-33 Fixed Disk Drive Test Error Codes The 1700 series of Diagnostic error codes identifies failures with fixed disk drives, fixed disk drive controller boards, fixed disk drive cabling, and system board functions. Corrective action may require replacement of fixed disk drive cables, fixed disk drive controller boards, fixed disks, or the system board assembly. If your system uses a drive array controller, see the section for Drive Array Advanced Diagnostics (DAAD).
3-34 Diagnostic Tools Tape Drive Test Error Codes The 1900 series of Diagnostic error codes identifies failures with tape cartridges, tape drives, tape drive cabling, adapter boards, or the system board assembly. Corrective action may require replacement of tape cartridges, tape drive cabling, adapter boards, tape drives, or the system board assembly. Table 3-12 Tape Drive Test Error Codes Error Code Description 1900-xx Tape ID failed. 1901-xx Tape servo write failed. 1902-xx Tape format failed.
3-35 Advanced VGA Board Test Error Codes The 2400 series of Diagnostic error codes identifies failures with video boards, monitors, or the system board assembly. Corrective action may require replacement of a monitor, video boards, or the system board assembly. Table 3-13 Advanced VGA Board Test Error Codes Error Code Description Recommended Action The following steps apply to error codes 2402-xx through 2456-xx: 2402-xx Video memory test failed. 2403-xx Video attribute test failed.
3-36 Diagnostic Tools Advanced VGA Board Test Error Codes Continued Error Code Description 2419-xx ECG/VGC ROM checksum test failed. 2420-xx ECG/VGC attribute test failed. 2421-xx ECG/VGC 640 x 200 graphics mode test failed. 2422-xx 2423-xx 2424-xx 2425-xx 2431-xx ECG/VGC 640 x 350 16-color set test failed. ECG/VGC 640 x 350 64-color test failed. ECG/VGC monochrome text mode test failed. 2432-xx ECG/VGC monochrome graphics mode test failed. 2448-xx 640 x 480 graphics test failure.
3-37 32-Bit DualSpeed NetFlex-2 Controller and 32-Bit DualSpeed NetFlex-2 Token Ring Controller Test Error Codes The 6000 series of Diagnostic error codes identifies failures with 32-bit DualSpeed NetFlex-2/Token Ring Controllers. Corrective action may require replacement of the 32-bit DualSpeed NetFlex-2/Token Ring Controller.
3-38 Diagnostic Tools Compaq Network Interface Cards Test Error Codes The 6000 series of Diagnostic error codes identifies failures with 32-bit DualSpeed NetFlex2/Token Ring Controllers. Corrective action may require replacement of the 32-bit DualSpeed NetFlex-2/Token Ring Controller. Table 3-15 Compaq Network Interface Cards Test Error Codes Error Code Description 6000-xx Network card ID failed. 6001-xx Network card setup failed. 6002-xx Network card transmit failed.
3-39 SCSI Fixed Disk Drive Test Error Codes The 6500 series of Diagnostic error codes identifies failures with SCSI fixed disk drives, SCSI fixed disk drive controller boards, SCSI fixed disk drive cabling, and system board functions. Corrective action may require replacement of fixed disk drive cables, fixed disk drive controllers, fixed disks, or the system board assembly. If your system uses a drive array controller, see the section for Drive Array Advanced Diagnostics (DAAD).
3-40 Diagnostic Tools SCSI Tape Drive Test Error Codes The 6700 series of Diagnostic error codes identifies failures with tape cartridges, tape drives, media changers, tape drive cabling, adapter boards, or the system board assembly. Corrective action may require replacement of a tape cartridge, tape drive, media changer, tape drive cabling, adapter board, or the system board assembly.
3-41 Server Manager/R Board Test Error Codes Continued Error Code 7000-25 7000-26 7000-27 7000-28 7000-33 7000-34 7000-35 7000-41 7000-42 7000-43 7000-44 7000-45 7000-46 7000-51 7000-52 7000-53 7000-54 7000-55 7000-56 7000-57 7000-61 7000-62 Description Memory Increment Memory Random Data. Memory Disturb Address. Memory HBM. HBM IO. HBM BMIC. HBM Video. ser_int. ser_int. ser_ext. ser_ext. ser_ext_int. ser_ext_int. mdm_int. mdm_int. mdm_ext. mdm_ext. mdm_ext_int. mdm_ext_int. mdm\c\analog.
3-42 Diagnostic Tools Drive Array Advanced Diagnostics (DAAD) Drive Array Advanced Diagnostics (DAAD) is a DOS-based tool designed to run on all Compaq products that contain a Compaq Drive Array Controller. The error messages and codes listed include all codes generated by Compaq products. Your system generates only codes applicable to your configuration and options.
3-43 Starting DAAD To start DAAD: 1. Insert the DAAD diskette into drive A. Reboot the system - OR - if you are at the DOS prompt, enter the following: A:DAAD NOTE: To generate a DAAD report without starting the interactive portion of the utility, enter the following at the DOS prompt: DAAD filename where filename is the name of the file or report. A dialog box is displayed, indicating the version of DAAD installed.
3-44 Diagnostic Tools Table 3-21 lists DAAD diagnostic messages in alphabetical order. Table 3-21 DAAD Diagnostic Messages Message Description Recommended Action Accelerator board not detected Array controller did not detect a configured array accelerator board. Install array accelerator board on array controller. If an array accelerator board is installed, check for proper seating on the array controller board.
3-45 DAAD Diagnostic Messages Continued Message Description Recommended Action Accelerator status: Unrecognized status A status returned from the array accelerator board that DAAD does not recognize. Accelerator status: Obsolete data sensed at reset During reset initialization obsolete data was found in the cache. This was due to the drives being moved and written to by another controller. Nothing needs to be done.
3-46 Diagnostic Tools longer in use.
3-47 DAAD Diagnostic Messages Continued Message Description Recommended Action Accelerator status: Data in the cache was lost due to some reason other than the battery being discharged Data in the cache was lost, but not because of the battery being discharged. Check to be sure that the array accelerator is properly seated. If the error continues you may need to replace the array accelerator. Accelerator status: Cache was automatically configured during last controller reset.
3-48 Diagnostic Tools attached with array accelerator board, but one is not attached. controller.
3-49 DAAD Diagnostic Messages Continued Message Description Recommended Action NVRAM configuration present, controller not detected EISA nonvolatile RAM has a configuration for an array controller but there is no board in this slot. Either a board has been removed from the system or a board has been placed in the wrong slot. Place the array controller in the proper slot or run the System Configuration Utility to reconfigure nonvolatile RAM to reflect the removal or new position.
3-50 Diagnostic Tools 102) Controller is located in special “video” slot Controller is installed in slot for special video control signals. If controller is used in this slot, LED indicators on front panel may not function properly. Install the controller in a different slot and run the System Configuration Utility to configure the controller and nonvolatile RAM.
3-51 DAAD Diagnostic Messages Continued Message Description Recommended Action Controller is not configured Controller is not configured. If controller was previously configured and you change drive locations, there may be a problem with placement of the drives. DAAD examines each physical drive and looks for drives that have been moved to a different drive bay. Look for messages indicating which drives have been moved.
3-52 Diagnostic Tools Drive (bay) X needs replacing (DAAD Error 102) The 210-megabyte hard drive has firmware version 2.30 or 2.31. Replace the drive. Drive Monitoring features are unobtainable DAAD unable to get monitor and performance data due to fatal command problem such as drive time-out, or unable to get data due to these features not supported on the controller. Check for other errors (time-outs, etc.).
3-53 DAAD Diagnostic Messages Continued Message Description Recommended Action Drive Monitoring is NOT enabled for drive bay X The monitor and performance features have not been enabled. Run the System Configuration Utility to initialize the monitor and performance features. Drive time-out occurred on physical drive bay X DAAD issued a command to a physical drive and the command was never acknowledged. The drive or cable may be bad.
3-54 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Recommended Action Identify controller data did not match with NVRAM The identify controller data from the array controller did not match with the information stored in nonvolatile RAM. This could occur if new, previously configured drives have been placed in a system that has also been previously configured.
3-55 status will occur. This status may also occur if another configured logical drive is in the WRONG DRIVE REPLACED or LOOSE CABLE DETECTED state.
3-56 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Recommended Action Logical Drive X status = INTERIM RECOVERY A physical drive in this logical drive has failed. The logical drive is operating in interim recovery mode and is vulnerable. Replace the failed drive as soon as possible. Logical Drive X status = LOOSE CABLE DETECTED A physical drive has a cabling problem. Turn the system off and attempt to reattach the cable onto the drive.
3-57 DAAD Diagnostic Messages Continued Message Description Recommended Action Mirror data miscompare Data was found at reinitialization in the posted write memory; however, the mirror data compare test failed resulting in data being marked as invalid. Data loss is possible. Replace the array accelerator board. Mirrored memory location errors Soft errors occurred when attempting to read the same data from both sides of the mirrored memory. Data loss will occur. Replace the array accelerator board.
3-58 Diagnostic Tools Drive (bay) X was inadvertently replaced The physical drive was incorrectly replaced after another drive failed. Replace the drive that was incorrectly replaced and replace the original drive that failed. Do not run the System Configuration Utility and try to reconfigure; data will be lost.
3-59 DAAD Diagnostic Messages Continued Message Description Recommended Action SCSI port X, drive ID Y firmware needs upgrading Drive’s firmware may cause problems and should be upgraded. Run Options ROMPaq to upgrade the drive’s firmware to a later revision. Set configuration command issued The configuration of the array controller has been updated. The array accelerator board may remain disabled until it is reinitialized.
3-60 Diagnostic Tools DAAD Diagnostic Messages Continued Message Description Recommended Action WARNING Drive Write Cache is enabled on X Drive has its internal write cache enabled. The drive may be a third-party drive or the drive’s operating parameters may have been altered. Condition may cause data corruption if power to the drive is interrupted. Replace the drive with a Compaq supplied drive, or restore the drive’s operating parameters.
3-61 Multiple Ways of Viewing the Log You can view an event in the IML in several ways: ■ On the Integrated Management Display ■ From within Compaq Insight Manager ■ From within Compaq Survey Utility ■ From within IML Management Utility Integrated Management Display The Integrated Management Display is a Liquid Crystal Display (LCD) panel that presents information directly at the server, assisting in diagnosing and servicing the server without a keyboard and monitor.
3-62 Diagnostic Tools Compaq Survey Utility The Compaq Survey Utility is a serviceability tool available from Windows NT and Novell NetWare that delivers online-configuration capture and comparison to maximize server availability. It is delivered on the Compaq Management CD in the SmartStart package or is available on the Compaq website. Refer to the Compaq Management CD for information on installing and running the Compaq Survey Utility.
3-63 Table 3-22 Event Messages Event Type Event Message Machine Environment Fan Failure System Fan Failure (Fan X, Location) Fan Inserted System Fan Inserted (Fan X, Location) Fan Removed System Fan Removed (Fan X, Location) Fans Not Redundant System Fans Not Redundant Overheat Condition System Overheating (Zone X, Location) Main Memory Correctable Error threshold exceeded Corrected Memory Error threshold passed (Slot X, Memory Module X) Corrected Memory Error threshold passed (System Memory)
3-64 Diagnostic Tools Event Messages Continued Event Type PCI Bus Error Event Message PCI Bus Error (Slot X, Bus X, Device X, Function X) Power Subsystem Power Supply Failure System Power Supply Failure (Power Supply X) Power Supply Inserted System Power Supply Inserted (Power Supply X) Power Supply Removed System Power Supply Removed (Power Supply X) Power Supply Not Redundant System Power Supplies Hot Redundant System Configuration Battery Low Power Module Failure Real-Time Clock Battery Faili
3-65 Rapid Recovery Services Compaq servers provide rapid recovery services for diagnosing and recovering from errors. These tools are available for local and remote diagnosis and recovery. Rapid recovery means fast identification and resolution of complex faults. The Rapid Recovery Engine and Insight Management Agents notify the system administrator when a failure occurs, ensuring that the server experiences minimal downtime. You enable these features through the System Configuration Utility.
3-66 Diagnostic Tools The available recovery features are: ■ Software Error Recovery – automatically restarts the server after a software-induced server failure ■ Environmental Recovery – allows the server to restart when temperature, fan, or AC power conditions return to normal Unattended Recovery For unattended recovery, ASR-2 performs the following actions: ■ Logs the error information to the IML ■ Resets the server ■ Pages you (if a modem is present and you selected paging) ■ Tries to restar
3-67 Hardware Requirements To use this level of ASR-2 over a modem, you need the following: ■ Compaq modem or optional Hayes modem ■ System Configuration Utility and Diagnostics Utility installed on the system partition of the hard drive ■ ASR-2 configured to load Compaq Utilities after restart You can also run Compaq Utilities remotely over an IPX or IP network using the Network feature: ■ To use Compaq Utilities on an IPX network, you must have Compaq Insight Manager 2.
3-68 Diagnostic Tools Compaq Integrated Remote Console The standard Compaq Integrated Remote Console performs a wide range of configuration activities.
3-69 The following ASR-2 flow chart shows you the sequence of events after a hardware or software error occurs: Hardware/Software error occurs | Error records in the Critical Error Log, or the Integrated Management Log, depending on your server configuration.
3-70 Diagnostic Tools Booting into Compaq Utilities When you enable ASR-2 to start into Compaq Utilities and a critical error occurs, the operating-system-specific Health Driver logs the error information in the Critical Error Log or the IML and the ASR-2 feature restarts the server. When the system reinitializes, the system pages the designated administrator (if enabled), and starts Compaq Utilities from the hard drive. If Dial-In status is enabled, the modem is placed in auto-answer mode.
3-71 Table 3-23 Compaq System Configuration Utility Pager Settings for Booting into Compaq Utilities Pager Data Setting Description Pager status Enabled Indicates if the pager feature is enabled or disabled. Pager dial string ATDT 555-5555 Indicates the pager dial string and delay before the pager message.
3-72 Diagnostic Tools Compaq System Configuration Utility Pager Settings for Booting into Compaq Utilities Continued Pager Data Dial-out status Setting Enabled Description Allows ASR-2 to dial out to a remote workstation. If you selected this option, Dial In Status is automatically selected. To use the dial-out feature, set Dial-Out Status to Enabled and set the Dial-Out String to the correct phone number. You must also set the Reset Boot option to Boot Compaq Utilities.
3-73 Compaq System Configuration Utility Pager Settings for Booting into Compaq Utilities Continued Pager Data Setting Description Network IP address Enter the IP address for this server in standard dot notation. Network IP net mask Enter the net mask for this server in standard dot notation. Network IP router address Enter the router to be used for this server in standard dot notation. NOTE: This is not used if you select Custom for Network controller. You must enter your IP address in the NET.
3-74 Diagnostic Tools ■ Network protocol IPX ■ Network controller Compaq ■ Network host name CPQHOU ■ Network card slot Slot # ■ Network frame type ETHERNET_II ■ Network IP address xxx.xxx.xxx.xxx ■ Network IP net mask xxx.xxx.xxx.xxx ■ Network IP router address xxx.xxx.xxx.xxx ASR-2 Security The standard Compaq password features function differently during ASR-2 than during a typical system startup. During ASR-2, the system does not prompt for the Power-On Password.
3-75 Critical Error Log The Critical Error Log records memory errors, as well as catastrophic hardware and software errors that cause the system to fail. This information helps you quickly identify and correct the problem, thus minimizing downtime. You can view the Critical Error Log through the Compaq Insight Manager. The Diagnostics Utility either resolves the error or suggests corrective action in systems that do not support event logs.
3-76 Diagnostic Tools Error Detected On Boot The server detected an error during the Power-On Self-Test (POST). Up Processor Prefailure A CPU has passed an internal corrected error threshold; excessive internal ECC cache errors .
3-77 Critical Error Log Messages Continued Message NMI - PCI Bus Parity Error Description A parity error was detected on the PCI bus. NMI - Expansion Board A board on the expansion bus indicated an error condition, resulting in a Error server failure. NMI - Expansion Bus Master Time-Out A bus master expansion board in the indicated slot did not release the bus after its maximum time, resulting in a server failure.
3-78 Diagnostic Tools Revision History Table Some errors can be resolved by reviewing changes to the server configuration. The server has an Automatic Revision Tracking (ART) feature that helps you review recent changes to the server configuration. One ART feature is the Revision History Table, which contains the hardware version number of the system board and any other system boards providing ART-compatible revision information.
3-79 Storage Fault Recovery Tracking This feature tracks over 12 failure-indication parameters, such as time-outs, spin-up, and selftest errors of SCSI drives. You can use these parameters to pinpoint failed storage subsystem components and to recover from controller or hard drive failure. Storage Automatic Reconstruction This feature automatically reconstructs data to an online spare or to a replaced drive if a drive fails.
3-80 Diagnostic Tools Remote Service Features Compaq servers have the following management features that you can access by modem or network: Table 3-26 Compaq Servers Remote Management Features Feature Description Service Session Provides remote access to all the utilities on the system partition, including Diagnostics utilities, Inspect, ROMPaq, Drive Array Advanced Diagnostics (DAAD), and the System Configuration Utility.
3-81 ROMPaq Using flash ROM in Compaq servers allows the firmware (BIOS) to be upgraded with system or option ROMPaq utilities. To upgrade the ROM: ■ Run the ROMPaq utility from the system partition, or ■ Insert a ROMPaq diskette into drive A and cold boot the system. The ROMPaq utility then checks the system and provides a choice (if more than one exists) of ROM revisions to which the system can be upgraded. This procedure is the same for both system and option ROMPaq utilities.
3-82 Diagnostic Tools ■ Asset Management - Exports asset information from the Compaq Insight Manager database to leading database and spreadsheet applications. ■ Remote Management - Manages in-band or out-of-band devices, online or offline, from any location. ■ Reporting - Using Automatic Data Collection, gathers historic performance information for graphing or export purposes.
4-1 Chapter 4 Connectors, Switches, and Jumpers This chapter provides connector, switch, and jumper information for the Compaq ProLiant 1600 Servers Supporting Pentium II Processors with 100 MHz GTL Bus. Figure 4-1 depicts the connectors and slots on the rear panel of the server. Table 4-1 gives corresponding connector/slot descriptions. 3 2 1 10 4 9 5 8 6 7 Figure 4-1.
4-2 Connectors, Switches, and Jumpers Processor Board Components Figure 4-2 depicts the Compaq ProLiant 1600 processor board components. Table 4-2 gives the corresponding component descriptions. 1 2 3 4 8 5 7 6 Figure 4-2.
4-3 External Connectors and LEDs Figure 4-3 depicts the Compaq ProLiant 1600 processor board external connectors and LEDs. Table 4-3 gives the corresponding connector and LED descriptions. 1 2 6 5 3 4 Figure 4-3.
4-4 Connectors, Switches, and Jumpers Bus Settings The bus/core frequency ratio switch is located on the Compaq ProLiant 1600 processor board. Table 4-4 gives the Compaq ProLiant 1600 processor board bus/core ratio settings.
4-5 System I/O Board Components Figure 4-4 depicts the Compaq ProLiant 1600 system I/O board components. Table 4-5 gives the corresponding component descriptions. 1 12 2 1 2 3 4 5 6 11 10 9 8 7 3 4 5 1 2 3 4 6 Figure 4-4.
4-6 Connectors, Switches, and Jumpers Rear Connectors Figure 4-5 depicts the Compaq ProLiant 1600 system I/O board rear connectors. Table 4-6 gives the corresponding connector descriptions. 1 2 4 3 Figure 4-5.
4-7 SW1 - System Maintenance Switch Table 4-7 defines the function for each SW1 switch setting on the Compaq ProLiant 1600 Servers system I/O board. The default positions are indicated below. See Figure 4-4 and Table 4-5 for the location of the switch. Table 4-7 SW1 - System Maintenance Switch Settings Switch Function ON OFF 1 Disable On-Board Video On-board video is disabled. Default 2 Lock configuration information You cannot change configuration information.
4-8 Connectors, Switches, and Jumpers Backplane Board Figure 4-6 depicts the Compaq ProLiant 1600 backplane board connectors. Table 4-8 gives the corresponding connector descriptions. 1 2 3 4 5 6 7 12 11 10 9 8 Figure 4-6. Backplane board connectors Table 4-8 Backplane Board Connectors Reference Backplane Connector Reference Backplane Connector 1 IDE 24X CD-ROM Signal Connector 7 SCSI A Bus 2 1.
5-1 Chapter 5 Physical, Operating, and Performance Specifications This section provides operating and performance specifications for Compaq ProLiant 1600 Servers Supporting Pentium II Processors with 100 MHz GTL Bus. ■ System Unit ■ Power Supply ■ Processor ■ SDRAM Dual Inline Memory Modules ■ 1.
5-2 Physical, Operating, and Performance Specifications System Unit Table 5-1 System Unit Specifications U.S. Metric Dimensions Height 18.63 in 47.32 cm Depth 22.67 in 57.58 cm Width 10.
5-3 Power Supply Table 5-2 Power Supply Specifications U.S. Metric Input Specifications Nominal Line Voltage 115 VAC 230 VAC Range Input Line 90 VAC - 132 VAC 180 VAC - 264 VAC Frequency Range 47Hz - 63Hz 47Hz - 63Hz Power Factor .98 .
5-4 Physical, Operating, and Performance Specifications SDRAM Dual Inline Memory Module (DIMM) Table 5-4 SDRAM DIMM Specifications Size 32, 64, 128, 256 MB Speed 100 MHz NOTE: Use only 32-, 64-, 128-, or 256- MB; 168-pin, 3.3 volt, 100 MHz, 72-bit wide, 4 clock, Registered SDRAM DIMMs. 1.44-MB Diskette Drive Table 5-5 1.44-MB Diskette Drive Specifications Size 3 1/2 in LED Indicators (front panel) Green Read/Write Capacity per Diskette (high/low density) 1.
5-5 IDE 24X CD-ROM Drive Table 5-6 IDE 24X CD-ROM Drive Specifications U.S. Metric Dimensions Height 1.68 in inserted 42.9 mm Depth 5.85 in 150.1 mm Width 8.11 in 208.0 mm 2.09 lb .950 g Weight Data Transfer Rate Sustained 150 KB/s (sustained 1X), 1200 KB/s (sustained 8X) Burst 4.0 MB/s Access Times (typical) Full Stroke 350 ms Random 150 ms Diameter 4.7 in, 3.15 in 12 cm, 8 cm Thickness .05 in 1.2 mm Track pitch 1.
5-6 Physical, Operating, and Performance Specifications IDE 24X CD-ROM Drive Specifications Continued U.S. Output Power Metric 0.
5-7 IDE/CD Cable Table 5-8 IDE/CD Cable Specifications Connector type Flat cable, socket, multi-contact strain relief Cable type 40 conduit flat cable Socket type 40 position (missing pin 28) Length 9 in Point-to-Point SCSI Cable Table 5-9 Point-to-Point SCSI Cable Specifications Connector type Wide SCSI Cable type 68 conduit flat cable Socket type 68 position wide SCSI Length 27 in Compaq ProLiant 1600 Servers Maintenance and Service Guide
Index-1 Inde x A access panel front removing and replacing 2-5 spare part number 1-3 left side removing and replacing 2-8 spare part number 1-3 power supply removing and replacing 2-28 spare part number 1-3 right side removing and replacing 2-10 spare part number 1-3 top removing and replacing 2-9 spare part number 1-3 access to utilities 3-2 Array Configuration Utility 3-2 ART (Automatic Revision Tracking), assembly version 3-65 ASR-2, (Automatic Server Recovery-2) booting into Compaq Utilities 3-58 opera
Index-2 components exploded view 1-2 processor board, illustrated 4-2 system I/O, illustrated 4-5 connectors 4-3 CD-ROM, backplane 4-8 diskette, backplane 4-8 ethernet 4-1 expansion slots 4-1 expansion system board, backplane 4-8 external SCSI 4-1 fan, backplane 4-8 IMD, backplane 4-8 keyboard 4-1 LED, backplane 4-8 mouse 4-1 network 4-1 parallel port 4-1 power 4-1 power supplies,backplane 4-8 power supply, backplane 4-8 processor board,backplane 4-8 RJ-45 4-1 SCSI A, backplane 4-8 SCSI B, backplane 4-8 vi
Index-3 exploded views mechanical parts 1-1 system components 1-2 external replacement battery installing 2-31 spare part number 1-3 external SCSI connector 4-1 F fans backplane connector 4-8 I/O with bracket, removing and replacing 2-18 I/O with bracket, spare part number 1-3 system fan, removing and replacing 2-18 feet exploded view 1-1 removing and replacing 2-7 floppy drive See diskette drive front bezel exploded view 1-1 plate exploded view 1-1 removing and replacing 2-6 spare part number 1-3 removin
Index-4 memory expansion board, illustrated 1-2 fault recovery tracking, defined 3-66 illustrated 1-2 removing and replacing 2-27 specifications 5-4 messages critical error log 3-63 DAAD diagnostic 3-38 event 3-51 modem communications, test error codes 3-26 when used with ASR-2 3-55 mouse connector 4-1 operating specifications 5-1 power supply backplane connector 4-8 illustrated 1-2 power cable connector, backplane connector 4-8 rear panel, spare part number 1-3 removing and replacing 2-28 spare part num
Index-5 ROMPaq Firmware Upgrade Utility 3-2 to upgrade the ROM 3-68 run utilities 3-2 S safety warnings 2-4 SCSI external connector 4-1 SCSI A bus backplane connector 4-8 SCSI B bus backplane connector 4-8 server health logs 3-62 slide rail, spare part number 1-4 SmartStart and Support Software CD-ROM 3-2 running utilities 3-3 SmartStart and Support Software CD-ROM 2-1 software error recovery 3-54 spare parts list 1-3 specifications CD-ROM drive 5-5, 5-7 CD-ROM drive cable 5-7 DIMMs 5-4 diskette drive 5-4
Index-6 V video display unit, test error codes 3-24 monochrome board, test error codes 3-25 video connector 4-1 W warnings rack 2-3 safety 2-4
