ProLiant 3000 Servers Setup and Installation Guide For use with 350-MHz or greater Intel processor-based servers only Second Edition (January 1999) Part Number 179776-002 Compaq Computer Corporation
Notice The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
iii Contents About This Guide Text Conventions........................................................................................................................ix Symbols in Text...........................................................................................................................x Symbols on Equipment................................................................................................................x Rack Stability .....................................................
iv Compaq ProLiant 3000 Server Features continued Security Features ..................................................................................................................... 1-8 Compaq Integrated Remote Console................................................................................ 1-9 Compaq Integrated Management Display (Optional on Tower Models) ......................... 1-9 Supported Drive Configurations.................................................................................
v Chapter 4 Installing Hardware Options Preparing the Server ................................................................................................................ 4-2 Accessing Non Hot-Plug Areas ............................................................................................... 4-5 Accessing System Board Components ............................................................................. 4-5 Installing Processor ...................................................................
vi Server Configuration and Utilities continued Loading Compaq Device Drivers ...........................................................................................5-15 Novell NetWare Device Drivers from Compaq ..............................................................5-15 Microsoft Windows NT Device Drivers from Compaq ..................................................5-16 SCO OpenServer and SCO UnixWare Device Drivers from Compaq............................
vii Regulatory Compliance Notices continued Laser Devices ..........................................................................................................................A-6 Laser Safety Warnings .....................................................................................................A-6 Compliance with CDRH Regulations ..............................................................................A-6 Compliance with International Regulations ............................................
viii About This Guide About This Guide This guide is designed to be used as step-by-step instructions for installation, and as a reference for operation, troubleshooting, and future upgrades. The power supplies in this computer system produce hazardous energy levels. The guide is for the person who installs, administers, and repairs servers.
ix Text Conventions This document uses the following conventions to distinguish elements of text: Keys Keys appear in boldface. A plus sign (+) between two keys indicates that they should be pressed simultaneously. USER INPUT User input appears in a different typeface and in uppercase. FILENAMES File names appear in uppercase italics. Menu Options, Command Names, Dialog Box Names These appear in initial capital letters. COMMANDS, DIRECTORY NAMES, and DRIVE NAMES These always appear in uppercase.
x About This Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. WARNING: Indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Indicates that failure to follow directions could result in damage to equipment or loss of information. IMPORTANT: NOTE: Presents clarifying information or specific instructions. Presents commentary, sidelights, or interesting points of information.
xi Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. Power Supplies or Systems marked with these symbols indicate the equipment is supplied by multiple sources of power.
xii About This Guide Getting Help If you have a problem and have exhausted the information in this guide, you can get further information and other help in the following locations. Compaq Website The Compaq website has information on this product as well as the latest drivers and Flash ROM images. You can access the Compaq website by logging on to the Internet at http://www.compaq.com.
1-1 Chapter 1 Compaq ProLiant 3000 Server Features Compaq ProLiant 3000 servers deliver Intel processor technology, expanded storage capacity, dual memory controllers, dual peer PCI buses, and advanced high-availability features. Performance is maximized with up to two Intel processors, a new system architecture that improves overall system bandwidth, and up to 4 GB of registered SDRAM Error Checking and Correction (ECC) memory.
1-2 Compaq ProLiant 3000 Server Features Cache Memory and System Architecture ■ 512-KB secondary (L2) cache ■ Highly parallel System Architecture with Dual Memory controllers and dual peer PCI buses System Memory ■ Supports registered SDRAM, 60-ns or faster, 32-, 64-, 128-, 256-, or 512-MB DIMMs ■ Expandable to 4 GB ■ Supports up to 8 memory DIMM modules, each DIMM socket supporting one DIMM module. One module is installed or removed at a time.
1-3 Media Bays The Compaq ProLiant 3000 server can house up to 12 mass storage devices. ■ Hot-Plug Drives ❏ Seven 1-inch drives or six 1.6-inch drives (Standard) ❏ Eight 1-inch drives or six 1.6-inch drives with optional Duplex Drive cage ❏ Ten 1-inch Ultra2 drives with optional Ultra2 simplex drive cage NOTE: An Ultra2-compatible array controller must be used with the Ultra2 simplex drive cage option. Connecting the Ultra2 simplex drive cage to the integrated SCSI ports is not supported.
1-4 Compaq ProLiant 3000 Server Features SCSI ■ Dual Channel Integrated Wide-Ultra SCSI-3 controller ■ The following optional controller boards are currently supported for controller duplexing or expanding storage capacity (see http://www.compaq.
1-5 System Management ■ The Server Parameter Tracking utility provides timely server environment and subsystem information by using a combination of hardware, firmware, and industry-standard management software. Information provided by this utility includes fault, performance, and configuration status. ■ The Server Fault Tolerance feature provides many disk subsystem and memory system error correction fault-tolerance options.
1-6 Compaq ProLiant 3000 Server Features Warranty ■ Pre-Failure Warranty on processors, memory, hard drives, and power supplies ■ 3-year next business day parts and labor coverage Management and Configuration Tools Compaq offers an extensive set of features and optional tools to support effective server management and configuration.
1-7 Disk Drive Fault Tolerance Disk drive fault tolerance for Compaq servers is covered in more detail in the Compaq Server Online Reference Guide on the Systems Reference Library (SRL) CD. The following Redundant Array of Inexpensive Disks (RAID) types are supported: ■ RAID 0 - no fault tolerance ■ RAID 1 - mirroring ■ RAID 4 - data guarding ■ RAID 5 - distributed data guarding Compaq Insight Manager Compaq Insight Manager is an easy-to-use utility for collecting server information.
1-8 Compaq ProLiant 3000 Server Features Automatic Server Recovery-2 (ASR2) If there is a critical system failure, Automatic Server Recovery-2 allows you to restart the server and page a designated system administrator. For more information, see the Compaq Server Online Reference Guide on the Systems Reference Library CD (SRL).
1-9 Compaq Integrated Remote Console When the Compaq ProLiant 3000 server is equipped with an optional supported modem, you can perform a wide range of configuration activities using the standard Compaq Integrated Remote Console (IRC).
1-10 Compaq ProLiant 3000 Server Features ■ Ease of Use - The Integrated Management Display provides a 16x4 character display and four button control panel to easily navigate through menus. For information about using the IMD, see Chapter 6. Supported Drive Configurations Standard server configurations can include as many as seven Smart Array family controllers.
2-1 Chapter 2 Installation Overview This chapter presents an overview of the installation and configuration procedure for Compaq ProLiant 3000 servers. For detailed discussions of rack installation, hardware option installation, and configuration, see the corresponding chapters in this guide. Topics in this chapter include: ■ Server Warnings and Precautions - This section presents the precautions and warnings necessary to ensure safe installation of your server.
2-2 Installation Overview Server Warnings and Precautions WARNING: To reduce the risk of personal injury from hot surfaces, allow the hot plug drives and internal system components to cool before touching. WARNING: To reduce the risk of electric shock or damage to the equipment: ■ ■ ■ ■ ■ Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded electrical outlet that is easily accessible at all times.
2-3 Pre-installation Planning This section discusses the power, grounding, and temperature requirements of the Compaq ProLiant 3000 server. Power Requirements WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not overload the AC supply branch circuit that provides power to the server. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements.
2-4 Installation Overview Grounding For proper operation and safety, this equipment is required to be properly grounded in accordance with NFPA 70-1993, Article 250. All power distribution devices, branch wiring, and receptacles must be "Listed" grounding type devices. When using power strips for electrical distribution, ensure that ground integrity is maintained for each connection made. Plug each component into a reliably grounded outlet.
2-5 Installation Procedure There are two installation procedures presented in the following paragraphs. Each procedure is a summary of the steps you will follow to install your Compaq ProLiant 3000 server. The procedure you will use depends on whether you are installing a rack-mount model or a tower model server. Detailed instructions for each of the numbered steps are included in later chapters of this guide. Installing a Rack-Mount Model 1. Select an appropriate site for your rack. 2.
2-6 Installation Overview 12. Connect cables: keyboard, mouse, monitor, network, and power cables. 13. Turn on the computer and insert the SmartStart and Support Software CD to configure and manage the server. When the server boots from the SmartStart program, it automatically starts the System Configuration Utility. See Chapter 5 for detailed information. 14. Register your server.
3-1 Chapter 3 Rack-Mountable Server Installation This chapter covers the following information: ■ How to attach the mounting hardware to the server and to the rack ■ How to install the server into the rack You may choose the optional installation service from Compaq to install your rack products. See “Optional Installation Service” at the end of this chapter. The Compaq Installing Rack Products CD is included with your server.
3-2 Rack-Mountable Server Installation ■ Installing Rack Products CD This set contains several CDs, which give a visual overview of operations required to configure a Compaq rack with rack-mountable components.
3-3 Rack Warnings and Precautions Before beginning these procedures, make sure you understand the following warnings and caution. WARNING: To reduce the risk of personal injury or damage to the equipment, at least two people are needed to safely unload the rack from the pallet. An empty 42U rack weighs 253 LB (115 kg), is over seven ft (2.1m) tall, and may become unstable when being moved on its casters.
3-4 Rack-Mountable Server Installation WARNING: Before beginning to work on the rack, be sure that the leveling jacks are extended to the floor, that the full weight of the rack rests on the level floor, and that either stabilizers are installed or that multiple racks are coupled together for stability. CAUTION: Do not place anything on power cords or cables. Arrange them so that no one may accidentally step or trip over them. Do not pull on a cord or cable.
3-5 Rack Temperature Requirements The operating temperature inside the rack will always be higher than the room temperature, and is dependent on the configuration of equipment in your rack. The TMRA for each piece of equipment should be checked before installation.
3-6 Rack-Mountable Server Installation Airflow Requirements Compaq ProLiant rack-mountable servers draw cool air in through the front door and exhaust warm air out the rear door of the server. Therefore, the front door of the rack must be adequately ventilated to allow ambient room air to enter the cabinet, and the rear door must be adequately ventilated to allow the warm air to escape from the cabinet. Do not block the ventilation apertures.
3-7 Unpacking the Server Unpack the server box and locate the materials and documentation necessary to install your rack-mountable server. Locating Materials and Documentation All of the equipment needed to install the ProLiant 3000 server in the rack is included with the rack and with the server. 2 1 3 7 6 4 5 Figure 3-1.
3-8 Rack-Mountable Server Installation Contents of the rack model server box include: ■ Compaq ProLiant 3000 server ■ Cables - refer to Cabling Guidelines for Compaq ProLiant 3000 Servers ■ Rack mounting hardware (numbers reference Figure 3-1) 1 One pair 26-inch slide rail assemblies 2 One pair slide rail mounting brackets 3 Cable management arm bracket 4 Cable management arm 5 Cable management arm screws 6 Plastic rail covers (one pair) 7 Cable management arm support bracket ❏ Template that can be u
3-9 ■ Documentation and software ❏ Server Setup and Management Pack ❏ Installing Rack Products CD ❏ Rack Builder Configuration Tool Available via the web at www.compaq.com ❏ Rack Information Library Available via the web at www.compaq.
3-10 Rack-Mountable Server Installation Preparing the Mounting Brackets and Slide Rail Assemblies Each pair of mounting brackets, with attached slide rail assemblies, supports one rack-mountable server. Figure 3-2. Rack mounting brackets; alignment tabs identify the front flanges Each slide rail assembly consists of an outer bracket rail and an inner component rail (see Figure 3-3).
3-11 Figure 3-3. Slide rail assembly (outer bracket rail and inner component rail IMPORTANT: To make the installation of the mounting bracket easier, attach the bracket rail to the rack mounting bracket before attaching the mounting bracket assembly to the rack. This way, the joined mounting bracket and bracket rail can be fastened to the rack as one assembly. Attaching the Bracket Rail to the Mounting Bracket Please read all of the following eight steps before you begin. 1.
3-12 Rack-Mountable Server Installation Figure 3-4. Removing the component rail from the bracket rail 3. Put the component rails to one side. You will attach them to the rack server chassis later, in the section, "Attaching Component Rails to the Server." The next figure shows the separated bracket rail with its inner sliding piece and the flat, one-piece component rail. Figure 3-5.
3-13 The bracket rail consists of a fixed outer rail that screws to the rack mounting bracket, and an inner slide on a steel ball bearing movement. This inner slide does not detach. Figure 3-6. Bracket rail with inner slide. The front of the rail is highlighted. 4. Lay the bracket rail inside the mounting bracket with the front of both pieces oriented in the same direction. Align the front screw holes in the mounting bracket and the bracket rail.
3-14 Rack-Mountable Server Installation 5. Extend the inner slide from the front of the bracket rail. With this piece extended, you will see two screw holes aligned in the mounting bracket and the bracket rail. These are the two exposed holes near the back end of the bracket rail and the front hole accessible through a slot in the inner slide. 6. Fasten the bracket rail to the mounting bracket with one 8-32 x 1/4-inch slotted screws. (Do not use nuts or washers with the screws.
3-15 1 2 3 2 6 26 Figure 3-7. Attaching the bracket rail to the mounting bracket You will use a total of four 8-32 x 1/4-inch slotted screws to fasten the bracket rail to the mounting bracket. When all five screws are fastened, the mounting bracket and bracket rail form a mounting bracket slide assembly that you will attach to the rack. 8. Repeat steps 4 through 7 with the other bracket rail and mounting bracket. You now have a pair of mounting bracket slide assemblies to be attached to the rack.
3-16 Rack-Mountable Server Installation Attaching the Mounting Bracket Slide Assembly to the Rack WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that the rack leveling feet are extended to the floor and support the full weight of the rack. Each rack must be level and stable. Racks that are not coupled together require the installation of stabilizers. This must be done before you perform any work on the rack.
3-17 IMPORTANT: The template is two-sided (front and back) and printed with arrows that show you where the screws will be inserted, both for the mounting bracket assemblies and for the thumbscrews that will secure the server's face plate to the front of the rack. Align the template carefully with the holes on the rack, to determine the exact placement of the screws. 2. When you mark the positioning of the mounting bracket screws, also mark the positioning in the front of the rack for the cage nuts.
3-18 Rack-Mountable Server Installation Figure 3-8. Measuring with the template 3. After marking the front of the rack, turn the template over and mark the back rails of the rack. Open the rear door of the rack to access the back rails. 4. On the back of the rack, mark the rail to show the top of the template. This will help you align a template for the next component.
3-19 3. Insert the tip of the fitting tool through the other side of the perforation and hook the opposite lip of the cage nut. Figure 3-9. Inserting cage nuts 4. Using the fitting tool as a lever, pry the cage nut into position. 5. Repeat for each cage nut. Attaching the Mounting Bracket Assembly to the Rack The tabs on the front of the mounting bracket help to align it with the front of the rack frame. Cage nuts are not used for the front attachment of the mounting bracket.
3-20 Rack-Mountable Server Installation 1. Attach a mounting bracket assembly to the front of the rack first, using one M6 x 1.0-12L Phillips screw in the bottom hole of the bracket. Do not use the washers supplied with the Compaq rack. IMPORTANT: Use only the bottom hole of the bracket as shown in Figure 3-10. Figure 3-10. Attaching mounting bracket assembly to the front of the rack 2. Carefully align the mounting bracket assembly with the rear rack frame. 3.
3-21 Top View CZR4-012.eps Figure 3-11. Cage nut and back of mounting bracket assembly installed 4. After attaching both mounting bracket assemblies to the rack, prepare the server for mounting in the rack. Compaq ProLiant 3000 Servers Setup and Installation Guide For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: D-CH03.
3-22 Rack-Mountable Server Installation Attaching Component Rails to the Server 1. Place the tab on a component rail at the front of the server chassis. The holes in the component rail will line up only one way with the chassis. 2. Attach the flat side of a component rail to each side of the server chassis with five 8-32 x 1/4-inch Phillips screws. Do not use washers with the screws. Figure 3-12.
3-23 Attaching the Cable Management Arm Bracket The cable management arm bracket fastens to the top right rear of the rack server's chassis. The bracket provides an attachment point for the cable management arm from the server to the rear frame of the rack. Attach the cable management arm bracket to the back of the server with two 6-32 x 1/4 Phillips screws. Attach the rack rail covers to the rack. Figure 3-13.
3-24 Rack-Mountable Server Installation Loading the Rack Server Load and secure the server to the rack with the face plate thumbscrews before continuing to attach any more mounting bracket assemblies. Make sure that this pair of brackets is correctly aligned and installed and that the server fits before you continue. WARNING: To reduce the risk of personal injury or damage to the equipment, a minimum of two people MUST lift the server into the rack. The server weighs 50 pounds (22.6 kilograms).
3-25 1. Pull the slide rails forward from the mounting brackets. 2. Carefully align the server's component rails with the rack's slide rails and slide the server into the rack. CAUTION: Be sure to keep the component parallel to the floor when sliding the component rails into the slide rails. Tilting the component up or down could result in damage to the rails. Figure 3-14.
3-26 Rack-Mountable Server Installation WARNING: To reduce the risk of personal injury, be careful when pressing the component rail release latches and sliding the component into the rack. The slide rails could pinch your fingertips. 3. Press the component rail release latch on either side of the server and slide the server into the rack. IMPORTANT: The first time you slide the component into the rack, you may have to apply some pressure.
3-27 1. For easier handling, first slide the server into the rack, then attach the cable management arm to the cable management arm bracket. If you attach the arm before loading the server in the rack, the arm may swing around and interfere with the loading process. 2. After you have loaded the server into the rack, attach one end of the cable management arm to the server's cable management arm bracket using two M6 x 1.0-12L Phillips screws. Align the arm to the bracket as shown in Figure 3-15.
3-28 Rack-Mountable Server Installation Figure 3-16. Attaching the cable management arm to the rear brace of the rack Attaching the Optional Cable Support The optional cable support attached to the rear of the rack on both sides. All cables to and from the server are tied to this support, which allows the server cables to stretch from the right rear of the server across to the cable channel on the other side of the rack, where the other cables are bundled in the cable channel.
3-29 Figure 3-17. Attaching the cable support to the cable management arm Optional Installation Service The installation service covers the entire hardware installation from unpacking the components to routing the cables and running a test of the system. In North America, Compaq will make all of the arrangements to have the rack system installed by qualified Guaranteed Service Providers. An order form with pricing is available from the Compaq fax retrieval service.
4-1 Chapter 4 Installing Hardware Options This chapter is divided into three major parts: ■ Preparing the Server - This section describes how to properly shut down your server in order to install hardware options.
4-2 Installing Hardware Options Preparing the Server WARNING: To reduce the risk of injury from electrical shock, remove all power cords to completely disconnect power from the system. WARNING: To reduce the risk of electric shock or damage to the equipment: ■ Do not disable the power cord grounding plug. The grounding plug is an important safety feature. ■ Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times.
4-3 1. Back up your server data. 2. Shut down the operating system in an orderly manner, as directed in your operating system instructions. 3. Power down the server and remove the power cord. IMPORTANT: The system power in the ProLiant 3000 server does not completely shut off with the front panel Power On/Standby switch. The two positions of the switch function as ON and STANDBY, rather than ON and OFF.
4-4 Installing Hardware Options 7. Slide the side cover toward the rear of the unit about 1 inch (2.5 cm), then remove the cover. COMPACT Figure 4-1. Removing the server cover For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-5 Accessing Non Hot-Plug Areas To install options, upgrades, or replacements in these areas, you must first shut down the server power. Accessing System Board Components With the access panel and processor removed, you should be able to locate and identify the System Board components shown in Figure 4-2. 1 2 3 4 5 6 7 8 9 10 11 12 13 31 14 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 Figure 4-2. System board features Table 4-1 System Board Features Ref.
4-6 Installing Hardware Options System Board Features Continued Ref.
4-7 System Board Switches Table 4-2 defines the System Configuration setting switches, 31 in Figure 4-2, on the system board. The Open (OFF) position is the default configuration for each switch.
4-8 Installing Hardware Options Installing Processor NOTE: To allow easier access, you can tilt the server on its right side (side opposite of the removed panel). Be sure to lock the casters if you tilt the server. NOTE: Your processor and Processor Power Module may differ from the models illustrated. For the location of the processor settings switch and Bus/Ratio settings, refer to the Hardware Installation and Configuration poster or to the hood label located on the small access panel. 1.
4-9 3. Install the Processor Power Module associated with the processor. 2 1 3 Figure 4-4. Installing the Processor Power Module 4. Set processor setting switch to the appropriate setting for your processor. NOTE: For the appropriate processor setting switch position, please refer to your server’s Hardware Installation and Configuration poster. 5. Restore server to normal operation. Reverse steps in section "Preparing the Server.
4-10 Installing Hardware Options Installing DIMM Memory 1. Prepare the server for installation. See section "Preparing the Server," outlined earlier in this chapter. 2. Install DIMMs as shown in Figure 4-5. For information on populating memory sockets, see the following section titled “Memory Sockets.” Figure 4-5. Latching DIMMs 3. Restore server to normal operation. Reverse steps in section, "Preparing the Server.
4-11 Memory Sockets For the best performance, DIMM sockets should be added alternating between system board memory sockets. For optimum performance, memory should be installed in the following sequence: DIMM 5 DIMM 1 DIMM 6 DIMM 2 DIMM 7 DIMM 3 DIMM 8 DIMM 4 NOTE: Refer to the following figure for the socket numbers. DIMM1 DIMM2 DIMM3 DIMM4 DIMM8 DIMM7 DIMM6 DIMM5 Figure 4-6.
4-12 Installing Hardware Options Installing PCI/ISA Expansion Boards 1. Prepare the server for installation. See section "Preparing the Server," outlined earlier in this chapter. 2. Install expansion board. Figure 4-7. Installing PCI/ISA expansion board NOTE: 3. There are no special considerations for populating the PCI/ISA slots. Restore server to normal operation. Reverse steps in section, "Preparing the Server.
4-13 Installing Fans 1. Prepare the server for installation. See section "Preparing the Server," outlined earlier in this chapter. 2. Install fan as shown in Figure 4-8. Refer to Figures 4-9 and 4-10 for fan slot location and fan header location. 1 Figure 4-8. Installing fan 3. Restore server to normal operation. Reverse steps in section "Preparing the Server." Fan 1 (CPU) Fan 3 (I/O) Fan 2 (CPU Redundant) Fan 4 (I/O Redundant) Figure 4-9.
4-14 Installing Hardware Options Fan 4 (IO Redundant) Fan 1 (CPU) Fan 3 (IO) Fan 2 (CPU Redundant) Figure 4-10. Fan header location Accessing Drive Cage and Media Bays These instructions cover the removal of the hot-plug SCSI drive cage and removable media cage, installation of the Simplex Enable board, and installation of optional tape drive. NOTE: Installation of the Simplex Enable board disables controller duplexing of the internal SCSI drives.
4-15 Figure 4-11. Loosen thumbscrews COMPACT Figure 4-12. Pull the drive cage partially out 4. Remove all cables from the back of the drive cage. 5. Completely remove the drive cage. Compaq ProLiant 3000 Servers Setup and Installation Guide For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-16 Installing Hardware Options Installing Simplex Enable Board Option NOTE: This procedure applies only if you have an optional Wide-Ultra duplex drive cage installed. 1. Prepare the server for installation. See section "Preparing the Server," outlined earlier in this chapter. 2. Remove drive cage. See section “Removing Drive Cage.” 3. Remove the Duplex Enable board from the back of the drive cage. Figure 4-13.
4-17 4. Insert the Simplex Enable board. Figure 4-14. Installing the Simplex Enable board CAUTION: The SCSI backplane board must have either a Duplex Enable board or a Simplex Enable board installed in order for the SCSI bus to be terminated properly. If neither of these boards is installed, the service LEDs of all drives will light as a warning. 5. Install drive cage. See section “Installing Drive Cage.
4-18 Installing Hardware Options Installing Tape Drive 1. Prepare the server for installation. See section "Preparing the Server," outlined earlier in this chapter. 2. Remove drive cage. See section “Removing Drive Cage.” 3. Remove face plate. CT COMPA 1 2 Figure 4-15. Removing face plate For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-19 4. Install tape drive into media bay. 2 2 CT COMPA 3 1 Figure 4-16. Installing tape drive 5. Install face plate. 6. Connect SCSI cable, located in the server, from the tape drive to the internal SCSI Port 1 or 2 or SCSI controller board in a PCI slot, if one is installed. NOTE: There are no special considerations as to which SCSI controller the tape drive is connected. 7. Install drive cage. See section “Installing Drive Cage.
4-20 Installing Hardware Options Installing Drive Cage NOTE: Your drive cage may differ from the model illustrated. 1. Replace the drive cage. Do not push it back fully until after you install cables. Figure 4-17. Re-installing the drive cage 2. Reconnect the SCSI cables on the back of the drive cage. Refer to Compaq ProLiant 3000 Servers Cabling Guidelines for information on SCSI cabling. 3.
4-21 Installing Integrated Management Display 1. Prepare the server for installation. See section "Preparing the Server," outlined earlier in this chapter. 2. Remove IMD blank. T COMPAC Figure 4-18. Removing IMD blank 3. Install IMD. 2 T COMPAC 2 2 1 2 Figure 4-19.
4-22 Installing Hardware Options 4. Connect IMD cable to system board. Figure 4-20. Connecting IMD cable 5. Restore server to normal operation. Reverse steps in section "Preparing the Server." For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-23 Accessing Hot-Plug Areas This section describes accessing the following areas: ■ Hot-Plug SCSI Drives ■ Hot-Plug Power Supplies Components in these areas have color-coded latches or levers to signify that they are hot-plug devices. Removing and Installing the Hot-Plug SCSI Drives Wide-Ultra Hard Drives 1 2 3 Figure 4-21. NOTE: Removing a Wide-Ultra hard drive Pinch both sides of drive levers to unlock, then swing the levers out.
4-24 Installing Hardware Options 2 1 Figure 4-22. Installing a Wide-Ultra hard drive Ultra2 Hard Drives 3 2 1 Figure 4-23. Removing an Ultra2 hard drive NOTE: Press the drive lever to unlock, then swing the lever out. For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-25 1 2 Figure 4-24. Installing an Ultra2 hard drive SCSI ID Numbers NOTE: The duplex information below applies only if you have the Wide-Ultra duplex drive cage installed. The Wide-Ultra simplex and Ultra2 simplex drive cages cannot be used in a duplex configuration. There are five possible numbering schemes, depending on whether you are using 1-inch height drives, 1.6-inch height drives, and a simplex, or duplex configuration. The following five figures illustrate these five schemes.
4-26 Installing Hardware Options 4 3 2 1 0 11 10 9 8 5 Figure 4-25. SCSI ID numbers - Single SCSI Channel Ultra2 simplex drive cage with 1-inch drives Figure 4-26. 3 Not Used 2 6 1 5 0 4 SCSI ID numbers - Single SCSI Channel Wide-Ultra drive cage (Simplex Mode) with 1-inch drives For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-27 SCSI Channel A or Channel B 3 6 1 5 0 4 Figure 4-27. SCSI ID Numbers - Single SCSI Channel Wide-Ultra drive cage (Simplex Mode) with 1.6-inch drives SCSI Channel A SCSI Channel B 3 3 2 2 1 1 0 0 Figure 4-28. SCSI ID Numbers - Dual SCSI Channels Wide-Ultra drive cage (Duplex Mode) with 1-inch drives SCSI Channel A SCSI Channel B 3 3 1 1 0 0 Figure 4-29. SCSI ID Numbers - Dual SCSI Channels Wide-Ultra drive cage (Duplex Mode) with 1.
4-28 Installing Hardware Options Accessing the Hot-Plug Power Supplies 1. Remove power supply plate. Figure 4-30. Removing power supply plate 2. Install power supply. 2 1 2 Figure 4-31. Installing power supply For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: E-CH04.
4-29 Pre-Failure Warranty The Compaq ProLiant 3000 server includes Pre-Failure Warranty for Pentium II processors, hard drives, power supplies, and DIMMs purchased from Compaq through an Authorized Compaq Reseller. Supported components are eligible for replacement under this warranty before they actually fail, if the system determines that these components have degraded below predetermined reliability thresholds within the product warranty period.
5-1 Chapter 5 Server Configuration and Utilities This chapter describes the tools that Compaq provides to assist you in the configuration and management of your Compaq ProLiant 3000 Server. Configuring the Server with SmartStart SmartStart is the intelligent way to configure the server and to load the system software, there by achieving a well-integrated server are ensuring maximum dependability and supportability.
5-2 Server Configuration and Utilities ACT COMP Figure 5-1. Inserting the CD-ROM 3. When the busy indicator lights, the drive is ready to receive commands. Data can be retrieved from the disc. For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: F-CH05.
5-3 Using the System Configuration Utility The Compaq System Configuration Utility performs a wide range of configuration activities, including: ■ Automatically configuring PCI and ISA Plug and Play boards ■ Providing switch and jumper settings ■ Resolving resource conflicts in areas such as memory, port addresses, and interrupt requests (IRQ) ■ Managing the installation of mass storage devices such as hard drives, tape drives, and diskette drives ■ Setting and storing power-on features like date
5-4 Server Configuration and Utilities For PCI boards, the utility reads the configuration options from the PCI board's configuration space from a PCI configuration file (.PCF). ■ Compaq Option Configuration Files diskette ■ Non-Compaq Option Configuration Files diskette ■ SmartStart and Support Software CD The .CFG file provides board resource requirements and switch and jumper setting alternatives.
5-5 Starting the System Configuration Utility To start the Compaq System Configuration Utility for the first time, refer to the SmartStart Installation poster. After the first time, access the System Configuration Utility as follows: 1. Press the Ctrl+Alt+Del keys to reboot the server. 2. When the following prompt appears at the top of the screen during Power-On Self-Test (POST), press the F10 key.
5-6 Server Configuration and Utilities System Configuration Utility Main Menu This overview of the main menu options explains how to access the main menu and how to set the power-on features. The following options are available from the main menu: ■ System Configuration - Takes you through the configuration process step-by-step. Select the System Configuration option when a configuration change is required.
5-7 Configuring Hardware When you select the Configure Hardware menu, a screen with five steps is displayed. A listing and a brief explanation of each step follows. Step 1: Important System Configuration Information This step provides an overview of the configuration process. Step 2: Add or Remove Boards Use this step to add the PCI or ISA boards to the configuration or remove any boards from the configuration. Step 3: View or Edit Details Use this step to make necessary configuration changes.
5-8 Server Configuration and Utilities Setting Power-On Defaults You can set and change the Power-On features at any time. 1. Select System Configuration from the Main Menu; then select Power-On Defaults. 2. Set the current date in the format: MM-DD-YYYY 3. Set the correct time in the format: HH:MM:SS 4. Set the Power-On Num Lock state: ( ) Off (*) On * This activates the numeric keypad when the computer is turned ON.
5-9 Creating a New System Partition If you used SmartStart to configure your server and install your operating system, this procedure (“Creating a New System Partition”) was done automatically for you. Use this procedure only if the operating system was not installed on the server and you wish to create a system partition. 1. Insert the Compaq SmartStart and Support Software CD in the CD-ROM drive and turn on the server.
5-10 Server Configuration and Utilities Verifying the System Partition To verify that the system partition exists: 1. Remove any media from the CD-ROM drive and the diskette drive. 2. Reboot the system by pressing Ctrl+Alt+Del or by turning the server OFF and then ON again. 3. Press the F10 key when the following prompt appears. Press "F10" key for System Partition Utilities IMPORTANT: The text appears for only two seconds. If you do not press F10 within the two seconds, you must reboot the server.
5-11 Configuration Backup The Configuration Backup option allows you to create a backup of the system configuration and to restore the system configuration from the backup. The following menu options are available: ■ Backup ■ Restore Configuration Backup and Configuration History Files When you save and exit the System Configuration Utility, the utility keeps a history of the configuration.
5-12 Server Configuration and Utilities Table 5-1 System Configuration History Log Files Filename Description SYSTEM.SCI Current configuration information SYSTEM1.SCI Previous configuration information SYSTEM2.SCI Previous configuration information (oldest) SYSTEM.CHL Textual representation of SYSTEM.SCI file SYSTEM1.CHL Textual representation of SYSTEM1.SCI file SYSTEM2.CHL Textual representation of SYSTEM2.
5-13 Configuring PCI Boards Automatically The system ROM automatically configures PCI boards. If a user selection is required, a POST message directs you to run the System Configuration Utility. Also, you may use the System Configuration Utility to change the default automatic settings. Removing Boards System ROM automatically reconfigures the server after a PCI board or DIMM is removed.
5-14 Server Configuration and Utilities First the utility prompts you to select the correct operating system. Use the arrow keys to select the operating system and press the Enter key. The utility then prompts you for the operating system CD or diskette. No operating systems ship with the server. Support for all operating systems may not be available on this SmartStart and Support Software CD. Some operating systems have driver support/updates but not an integrated SmartStart installation.
5-15 Loading Compaq Device Drivers Drivers are located on the Compaq SmartStart and Support Software CD. IMPORTANT: Always check README files on the SmartStart and Support Software CD. If present, these files may contain information about important software updates. Novell NetWare Device Drivers from Compaq Your server must have certain device drivers to operate using NetWare. These drivers are located on the Compaq SmartStart and Support Software CD shipped with the server.
5-16 Server Configuration and Utilities Microsoft Windows NT Device Drivers from Compaq Drivers are supplied to support Windows NT 3.51 and 4.0. They are located on the SmartStart and Support Software Diskette CD, and some of the drivers are contained on the Windows NT retail product. These drivers are also located on the Compaq SmartStart and Support Software CD. The drivers on the SSD may be newer versions with new functionality, problem fixes, and so on.
5-17 SCO OpenServer and SCO UnixWare Device Drivers from Compaq Your server must have certain device drivers to operate under the SCO OpenServer and SCO UnixWare 2.1 operating systems. These drivers are located on the Compaq SmartStart and Support Software CD shipped with the server. If you use SmartStart to install your operating system, these drivers will be installed automatically.
5-18 Server Configuration and Utilities IBM OS/2 Device Drivers from Compaq Your server must have certain device drivers for some server options to operate using IBM OS/2 Warp Server 4.0, IBM OS/2 Warp Server 4.0 SMP, IBM OS/2 Warp, IBM OS/2 Warp Connect 3.0, and OS/2 2.x. These drivers are located on the Compaq SmartStart and Support Software CD you received with your server. If you use SmartStart to install your operating system, these drivers are loaded automatically.
5-19 Banyan VINES Device Drivers from Compaq Your server must have certain device drivers for some server options to operate using the Banyan VINES operating system. Compaq provides driver support for Banyan VINES 6.x and 7.x. These drivers are located on the Compaq SmartStart and Support Software CD you received with your server. You can use SmartStart to create a Banyan VINES Support Software Diskette (SSD) from Compaq to support a manual installation of Banyan VINES.
5-20 Server Configuration and Utilities Diagnostics and Other Utilities ■ When you select the Diagnostics and Utilities feature from the System Configuration Utility main menu, the utility provides prompts to test, inspect, upgrade, and diagnose the server. ■ Diagnostics and Utilities are located on the system partition on the hard drive and must be accessed when a system configuration error is detected during the Power-On Self-Test (POST).
6-1 Chapter 6 Integrated Management This chapter contains instructions and guidelines for using the Integrated Management features in Compaq ProLiant 3000 servers that may not be familiar to you. Subjects covered are: ■ Integrated Management Display ■ Integrated Management Log Integrated Management Display (Optional on Tower Models) The Compaq Integrated Management Display (IMD) is an integrated, 16x4 character display mounted on the front of the server.
6-2 Integrated Management If there are no errors, you will see the Idle Screen text. Figure 6-1 shows the default screen, but this screen could be different if you changed the text during configuration. COMPAQ PROLIANT 3000 ESC Figure 6-1. Idle screen text For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: G-CH06.
6-3 Navigation Buttons To navigate through the menus, use the four buttons shown in Figure 6-2. The Up and Down arrow keys ( and ) allow you to move through the menu screens and choose menu items. The right button ( ) acts as an Enter key and allows you to travel down through the menus. The left button ( ) acts as an Escape key and allows you to travel back up the menu. ESC 1 3 4 2 Figure 6-2.
6-4 Integrated Management Display Symbols There are three different display symbols used to indicate your options as you scroll through the menus. These on-screen symbols are the Up and Down arrows and the Selector arrow. Table 6-1 Integrated Management Display Symbols Type of Symbol Symbol Meaning Arrow Selector arrow shows current menu item. Press Enter on the IMD to select the menu item to the right of this arrow. Up Arrow If present in upper right corner, indicates previous information exists.
6-5 System Behavior with Error Events After system POST, if there is an F1 error condition, the IMD flashes this message: LCD-013.EPS !ALERT! Press Any Key to View New Events ESC Figure 6-3. New Event Message At this point, you must scroll through each screen of the event information menu before the IMD will allow you to move on to other menu choices. The display will not allow you to escape the Unviewed Events section until you have examined all of the information stored here.
6-6 Integrated Management Menu Structure The following outline shows the structure of each menu and submenu in the order in which it appears: Events Event List Administration Information ■ ■ ■ ■ Server ❏ Server Name ❏ Asset Tag ❏ Operating System ❏ Other Administrator ❏ Name ❏ Phone ❏ Pager ❏ Other Service ❏ Name ❏ Phone ❏ Pager ❏ Other Custom Menu Item (if entered) ❏ Custom Menu Screen (if entered) For use with 350-MHz or greater Intel processor-based servers only Writer:
6-7 System Information ■ ROM Date ■ BootBlock Date ■ Memory ■ Processors Contrast ■ Contrast ■ Other Info. All of these menu items can be changed using the Compaq System Configuration Utility or an operating specific utility. Refer to the Compaq SmartStart and Support Software CD for instructions on installing the appropriate utility. Integrated Management Log The Compaq Integrated Management Log (IML) records system events and stores them in an easily-viewable form.
6-8 Integrated Management Multiple Ways of Viewing the Log You can view an event in the Integrated Management Log in several ways: ■ On the Integrated Management Display ■ From within Compaq Insight Manager ■ From within Compaq Survey Utility ■ From within operating system-specific utilities. Refer to your operating system support software for more information.
6-9 Viewing the Event List 1. From Compaq Insight Manager, select the appropriate server, then select View Device Data. The selected server is displayed with buttons around its perimeter. 2. Select the Recovery button. 3. Select Integrated Management Log. NOTE: You can only view the list from the Recovery/Integrated Management screen. To print the list, follow the instructions below. 4. If a failed component has been replaced, select the event from the list, then select Mark Repaired.
6-10 Integrated Management Compaq Survey Utility The Compaq Survey Utility is a serviceability tool available for Windows NT and Novell NetWare that delivers on line configuration capture and comparison to maximize server availability. It is delivered on the Compaq Management CD in the Server Setup and Management package, or it is available on the Compaq website. Refer to the Compaq Management CD for information on installing and running the Survey Utility.
6-11 List of Events The event list displays the affected components and the associated error messages. Though the same basic information is displayed, the format of the list may be different depending on how you are viewing it: on the Integrated Management Display, from within Compaq Insight Manager, or from within the Compaq Survey Utility.
6-12 Integrated Management Table 6-2 Event Messages Event Type Event Message Machine Environment Fan Failure System Fan Failure (Fan X, Location) Fan Inserted System Fan Inserted (Fan X, Location) Fan Removed System Fan Removed (Fan X, Location) Fans Not Redundant System Fans Not Redundant Overheat Condition System Overheating (Zone X, Location) Main Memory Correctable Error threshold exceeded Corrected Memory Error threshold passed (Slot X, Memory Module X) Corrected Memory Error threshold p
6-13 Event Messages Continued Event Type Event Message Power Subsystem Power Supply Failure System Power Supply Failure (Power Supply X) Power Supply Inserted System Power Supply Inserted (Power Supply X) Power Supply Removed System Power Supply Removed (Power Supply X) Power Supply Not Redundant System Power Supplies Not Redundant System Configuration Battery Low Real-Time Clock Battery Failing Power Module Failure A CPU Power Module (System Board, Socket X) A CPU Power Module (Slot X, Socket X)
A-1 Appendix A Regulatory Compliance Notices Regulatory Compliance Identification Numbers For the purpose of regulatory compliance certifications and identification, your ProLiant 3000 Server is assigned a Compaq Series number. The Compaq Series number for this product is: Series ES1003. The Server Series Number can be found on the product label, along with the required approval markings and information. See “Label Location” at the end of this appendix for the location of the label on this product.
A-2 Regulatory Compliance Notices Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
A-3 Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product, contact: Compaq Computer Corporation P. O.
A-4 Regulatory Compliance Notices Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Canadian Notice (Avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
A-5 Japanese Notice Taiwanese Notice Compaq ProLiant 3000 Servers Setup and Installation Guide For use with 350-MHz or greater Intel processor-based servers only Writer: Cheri Stewart Project: Compaq ProLiant 3000 Servers Setup and Installation Guide Comments: 179776-002 File Name: H-APPA.
A-6 Regulatory Compliance Notices Laser Devices The CD-ROM drive contains a laser device. All Compaq systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product.
A-7 Laser Product Label The following label or equivalent is located on the surface of your CD-ROM drive. This label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label appears on a laser device installed in your product. Laser Information Laser Type Semiconductor GaAIAs Wave Length 780 nm +/- 35 nm Divergence Angle 53.5 degrees +/- 0.5 degrees Output Power Less than 0.2 mW /10,869 W·m-2 sr-1 Polarization Circular 0.25 Numerical Aperture 0.45 inches +/- 0.
A-8 Regulatory Compliance Notices Battery Replacement Notice Your server is provided with a Lithium Manganese Dioxide, or a Vanadium Pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by a Compaq Authorized Service Provider using the Compaq spare designated for this product.
A-9 Regulatory Compliance Label Location The Regulatory Compliance label for your ProLiant 3000 server is located inside the Right Side Access Panel toward the rear as shown in the below figure. To view this information, remove right side access panel. COMPAQ COMPUTER CORPORATION PRODUCT OF THE U.S.A.
B-1 Appendix B Power Cord Set Requirements The power cord set meets the requirements for use in the country where you purchased your equipment. The voltage selection switch allows you to select the appropriate line voltage for your server. Power cord sets for use in other countries must meet the requirements of the country where you use the server. For more information on power cord set requirements, contact your Authorized Compaq Dealer.
B-2 Power Cord Set Requirements Country-Specific Requirements Use the following table to identify the appropriate accredited agency in your country.
B-3 Power Cord Set Requirements- By Country Continued Country Accredited Agency Applicable Note Numbers Switzerland SEV 1 United Kingdom BSI 1 United States UL 2 NOTES: 1. Flexible cord must be Type HO5VV-F, 3-conductor, 1.0 mm2 conductor size. Power cord set fittings (appliance coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it will be used. 2. Flexible cord must be Type SVT or equivalent, No. 18 AWG, 3-conductor.
C-1 Appendix C Internal CD-ROM Drive The Internal CD-ROM drive is a random access, read-only storage device capable of retrieving data from removable compact disc media, which can store up to 680 MB of digital information. COMPACT 1 2 3 4 5 6 Figure C-1.
Index-1 Index A About This Guide viii AC current load 2-3 accessing DIMM memory sockets 4-10 hot-plug areas 4-23 IMD 4-21 PCI/ISA slots 4-12 processor 4-8 system board components 4-5 System Configuration Utility 5-5, 5-6 airflow, requirements 3-6 architecture 1-2 arrow keys, IMD 6-3 ASR-2 1-6, 1-8 error events 6-13 assembly 4-1 automatic configuration 5-3 Automatic Server Recovery-2 See ASR-2 auxiliary power connector 4-5 B backplane boards drive cage 4-1 power supply 4-1 backup, configuration 5-11 Banyan
Index -2 component rails 3-10, 3-11, 3-12, 3-22, 3-26.
Index-3 DIMMs configuration, removal 5-13 latching, illustrated 4-10 sockets 1-2, 4-10, 4-11 disassembly 4-1 diskette drive 1-3 display symbols, IMD 6-4 documentation, locating 3-7 drive cages 4-14, 4-15, 4-16, 4-20, 4-25 backplane board 4-1 connectors 4-20 installation, illustrated 4-20 latch, illustrated 4-15 removal 4-14 removal, illustrated 4-15 drivers See device drivers drives See hard drives dual memory controllers 1-2 duplex enable board 4-14, 4-16, 4-17, 4-25 installation 4-14 removal, illustrated
Index -4 hardware configuring menu 5-7 interrupt 5-4 mounting 3-1 mounting kit 3-11 options 4-1 rack mounting 3-7, 3-8 health logs, server 1-6 high-availability features 1-4 history log files, configuration 5-11 hot-plug areas 4-1 power supplies 4-23 power supply 4-28 SCSI drives 4-23, 4-24 http //www.compaq.
Index-5 installation Continued simplex enable board 4-14, 4-16 simplex enable board, illustrated 4-17 tape drive 4-18 tools needed for rack model server 3-9 tower 2-6 Installing Rack Products CD 3-2, 3-9 integrated cache 1-2 Integrated Management Display 1-6, 6-1 arrow keys 6-3 buttons, illustrated 6-3 check mark 6-1 connector 4-5 default screen, illustrated 6-2 definition 1-5 displaying server error 6-1 error events, illustrated 6-5 event message, illustrated 6-5 features 1-9 firmware revision 6-1 idle sc
Index -6 M N management and configuration tools 1-6 management, system 1-5 mass storage devices See hard drives materials, locating 3-7 media bays 1-3, 4-14 memory 1-2 cache 1-2 controllers 1-2 ECC 1-1 error events 6-12 maximum 1-2 nonvolatile 5-3 pre-failure warranty 4-29 socket numbering, illustrated 4-11 sockets 4-10, 4-11 system 1-2 video 1-3 menu structure, IMD 6-6 Microsoft Windows NT 5-13, 5-14 device drivers 5-16 mounting brackets 3-8, 3-10, 3-11, 3-13, 3-14, 3-15, 3-16, 3-17, 3-19, 3-20, 3-21, 3
Index-7 P panels, blanking 3-6 partition copy files 5-8 creating 5-8 creating system 5-9 delete files 5-8 deleting 5-8 system 5-8 upgrading 5-8 verifing 5-10 pass-thru board removal 4-14, 4-17 PCI boards, error events 6-12 configuration 5-13 configuration files See .
Index -8 rack Continued mounting hardware 3-8 mounting hardware, illustrated 3-7 server cable management arm 3-26 server safety 3-24 slide rail assembly 3-11 stability warning 3-16 temperature requirements 3-5 template 3-8, 3-16 tools needed for installation 3-9 unpacking the rack server 3-7 Rack Builder Configuration Tool CD 3-1, 3-2, 3-9 Rack Information Library CD 3-9 RAID levels 1-7 rails assembly 3-10 attaching 3-11 bracket 3-10, 3-11, 3-12, 3-13, 3-14, 3-15 component 3-10, 3-11, 3-12, 3-22, 3-25, 3
Index-9 SCSI 1-4 cables 4-20 connector, internal 4-5 controller 1-4 controller cables 4-20 controllers 1-4 drive bays 1-4, 4-1 drive cage removal 4-14 drive configurations 1-10 drives 4-14 drives, hot-plug 4-23 duplex board installation 4-14 ID numbering, illustrated 4-26 ID numbers 4-25 optional controllers 1-4 pass-thru board removal 4-14 storage capacity 1-10 support 1-4 Wide Ultra 1-1 SDRAM 1-1.
Index -10 sockets memory 4-1 processor 4-1 Software Support 5-1 Solaris 5-13 spinning bar, IMD 6-1 SRL See Systems Reference Library storage devices 1-3.
Index-11 temperature maximum 2-4, 3-5 table 3-5 operating 3-5 rack requirements 3-5 server requirements 2-4 template 3-16, 3-17, 3-18 illustrated 3-18 rack 3-8 rack server 3-16 Text Conventions ix time, setting 5-8 tools fitting tool for cage nuts 3-18 for rack model server installation 3-9 VINES device drivers 5-19 W warnings rack 3-3 rack stability 3-16 server 2-1, 2-2 Warp 5-13 Warp Server Advanced 5-13 warranty DIMM memory 4-29 general 1-6 hard drives 4-29 power supplies 4-29 pre-failure 4-29 process
