ProLiant 3000 Setup and Installation Guide Second Edition (April 1998) Part Number 296908-002 Compaq Computer Corporation
Notice The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
iii Contents About This Guide How this Manual is Organized.................................................................................................. viii Text Conventions ........................................................................................................................ ix Symbols in Text............................................................................................................................ x Product Safety Information .......................................
iv About This Guide Compaq ProLiant 3000 Server Features continued Security Features ....................................................................................................................... 1-8 Compaq Integrated Remote Console ................................................................................. 1-9 Compaq Integrated Management Display ......................................................................... 1-9 Supported Drive Configurations .....................................
v Chapter 4 Installing Hardware Options Accessing Non Hot-Plug Areas................................................................................................. 4-2 Accessing Processors, Memory Board, and System Board ............................................... 4-2 Accessing the Drive Cage Back Plane............................................................................. 4-11 Replacing the Side Access Panel .....................................................................................
vi About This Guide Chapter 6 Integrated Management Integrated Management Display ............................................................................................... 6-1 Normal Run-time Behavior................................................................................................ 6-1 Navigation Buttons ............................................................................................................ 6-3 Display Symbols ........................................................
vii Appendix C Internal CD-ROM Drive Index ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: A-FRNT.
viii About This Guide About This Guide The Compaq ProLiant 3000 Setup and Installation Guide is intended to help you set up your server for optimal performance. Use this guide with the technical information on the configuration and installation poster, the hood labels, the Systems Reference Library CD, the SmartStart and Support Software CD, and the Management CD for complete and comprehensive reference source materials.
ix Text Conventions This document uses the following conventions to distinguish elements of text: Keys Keys appear in boldface. A plus sign (+) between two keys indicates that they should be pressed simultaneously. USER INPUT User input appears in a different typeface and in uppercase. FILENAMES File names appear in uppercase italics. Menu Options, Command Names, Dialog Box Names These appear in initial capital letters.
x About This Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. ! WARNING: Indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Indicates that failure to follow directions could result in damage to equipment or loss of information. IMPORTANT: Presents clarifying information or specific instructions. NOTE: Presents commentary, sidelights, or interesting points of information.
xi Any RJ-45 receptacle marked with these symbols indicates a Network Interface Connection. WARNING: To reduce the risk of electrical shock, fire, or damage to the equipment, do not plug telephone or telecommunications connectors into this receptacle. Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists.
xii About This Guide Getting Help If you have a problem and have exhausted the information in this guide, you can get further information and other help in the following locations.
xiii Compaq Management CD Compaq Management CD is located in Server Setup and Management pack and contains: Insight Manager Utility software Online Help for the Insight Manager Utility Other Hardcopy Documents The following hardcopy documents are provided with the server: Hood labels located on the inside of Side Access Panel and Top Access Panel Cabling Guidelines for Compaq ProLiant 3000 Servers Compaq ProLiant 3000 Hardware Installation and Configuration Poster Compaq Web Site T
xiv About This Guide Telephone Numbers For the name of your nearest Compaq Authorized Reseller: In the United States, call 1-800-345-1518 In Canada, call 1-800-263-5868 For Compaq technical support: In the United States and Canada, call 1-800-386-2172 Elsewhere, call one of the numbers listed in the following table.
xv Compaq Worldwide Technical Support Telephone Numbers continued Location Europe/Middle East/Africa Finland France Germany Hong Kong Hungary India Italy Japan Korea Malaysia Mexico Netherlands New Zealand Norway Poland Portugal Singapore South Africa Spain Sweden Switzerland Taiwan Thailand United Kingdom United States Venezuela Voice (49) 089-9933-2891 9800-206-720 (+358-800-1-206720) (33 1) 41-33-4455 0180-5-212111 852-90116633 36-1-201-8776 (91-80) 559-6023 392-57-90300 0120-101589 82-2-523-3575 (603)
xvi About This Guide Compaq Worldwide Technical Support Telephone Numbers continued Location Europe/Middle East/Africa Finland France Germany Hong Kong Hungary India Italy Japan Korea Malaysia Mexico Netherlands New Zealand Norway Poland Portugal Singapore South Africa Spain Sweden Switzerland Taiwan Thailand United Kingdom United States Venezuela Voice (49) 089-9933-2891 9800-206-720 (+358-800-1-206720) (33 1) 41-33-4455 0180-5-212111 852-90116633 36-1-201-8776 (91-80) 559-6023 392-57-90300 0120-101589 8
1-1 Chapter 1 Compaq ProLiant 3000 Server Features Compaq ProLiant 3000 servers deliver state-of-the-art Intel Pentium II processor technology, expanded storage capacity, dual memory controllers, dual peer PCI buses, and advanced high-availability features. Performance is maximized with up to two Pentium II processors, a new system architecture that improves overall system bandwidth, and up to 512 megabytes (for 300MHz models) or up to 3 gigabytes (for 333MHz models) of buffered EDO ECC memory.
1-2 Compaq ProLiant 3000 Server Features Cache Memory and System Architecture ■ 512-KB secondary (L2) cache ■ Compaq ProLiant 3000 System Architecture with Dual Memory controllers and Dual Peer PCI buses System Memory ■ 64-MB standard, extended data out (EDO), error checking and correcting (ECC) DIMMs ■ Supports EDO buffered, 60-ns or faster, 32-, 64-, 128-, or 256-MB, , 4-K or 8-K refreshed DIMMs. NOTE: Memory option kits contain two DIMMs to equal the total memory.
1-3 Media Bays The Compaq ProLiant 3000 server can house up to 12 mass storage devices. ■ Internal Drives - the server can be configured in either Simplex or Duplex drive cage configurations. Simplex mode configures the drive cage into a single drive cage attached to a single SCSI channel. Duplex mode configures the drive cage into two separate drive cages that are connected to separate SCSI channels.
1-4 Compaq ProLiant 3000 Server Features SCSI ■ Dual Channel Integrated Wide-Ultra SCSI-3 controller ■ The following optional controller boards are currently supported for controller duplexing or expanding storage capacity (see http://www.compaq.
1-5 ■ Integrated Management Display (IMD) offers a text-based user interface. The IMD displays and stores key system events at the server so that critical information is at your fingertips. ■ Integrated Management Log (IML) provides a detailed log of key system events. This log is accessible through Insight Manager, the Remote Insight board, the Compaq Survey utility, the Compaq IML Management utility, and the IMD.
1-6 Compaq ProLiant 3000 Server Features Management and Configuration Tools Compaq offers an extensive set of features and optional tools to support effective server management and configuration.
1-7 Disk Drive Fault Tolerance Disk drive fault tolerance for Compaq servers is covered in more detail in the Compaq Server Online Reference Guide on the Systems Reference Library (SRL) CD.
1-8 Compaq ProLiant 3000 Server Features Automatic Server Recovery-2 (ASR2) If there is a critical system failure, Automatic Server Recovery-2 allows you to restart the server and page a designated system administrator. For more information, see the Compaq Server Online Reference Guide on the Systems Reference Library CD (SRL).
1-9 Compaq Integrated Remote Console When the Compaq ProLiant 3000 server is equipped with an optional supported modem, you can perform a wide range of configuration activities using the standard Compaq Integrated Remote Console (IRC).
1-10 Compaq ProLiant 3000 Server Features ■ Ease of Use - The Integrated Management Display provides a 16x4 character display and four button control panel to easily navigate through menus. For information about using the IMD, see Chapter 6, “Advanced Feature Operation.” Supported Drive Configurations Standard server configurations can include as many as seven SMART-2 or SMART-2SL Controllers, depending on the installed network operating system.
1-11 Interlock Switches WARNING: To reduce the risk of personal injury from contact with hazardous energy, the equipment is provided with safety interlocks. Do not try to defeat these safety interlocks. If an access cover is removed, the power supply is disabled until the cover is properly replaced. Compaq ProLiant Servers contain built-in interlock switches. This feature: ■ Automatically turns the power off when you remove the server side or top covers ensuring your personal safety.
2-1 Chapter 2 Installation Overview This chapter presents an overview of the installation and configuration procedure for Compaq ProLiant 3000 servers. You are referred to later chapters in this guide for detailed discussions of rack installation, hardware option installation, and configuration. Topics in this chapter include: ■ Server Warnings and Precautions - This section presents the precautions and warnings necessary to ensure safe installation of your server.
2-2 Installation Overview Server Warnings and Precautions WARNING: To reduce the risk of personal injury from hot surfaces, allow the hot plug drives and internal system components to cool before touching. WARNING: equipment: To reduce the risk of electric shock or damage to the ■ Do not disable the power cord grounding plug. The grounding plug is an important safety feature. ■ Plug the power cord into a grounded electrical outlet that is easily accessible at all times.
2-3 Pre-installation Planning This section discusses the power, grounding, and temperature requirements of the Compaq ProLiant 3000 server. Power Requirements WARNING: To reduce the risk of personal injury, fire, or damage to the equipment, do not overload the AC supply branch circuit that provides power to the server. Consult the electrical authority having jurisdiction over your facility wiring and installation requirements.
2-4 Installation Overview This product is also designed for IT power system with Phase to Phase voltage 230 V. For electrical power ratings on options, refer to the product's rating label or user documentation supplied with that option. Grounding For proper operation and safety, this equipment is required to be properly grounded in accordance with NFPA 70-1993, Article 250. All power distribution devices, branch wiring, and receptacles must be "Listed" grounding type devices.
2-5 Installation Procedure There are two installation procedures presented in the following paragraphs. Each procedure is a summary of the steps you will follow to install your Compaq ProLiant 3000 server. The procedure you will use depends on whether you are installing a rack-mount model or a tower model server. Detailed instructions for each of the numbered steps are included in later chapters of this guide. Installing a Rack Mount Model 1. Select an appropriate site for your rack.
2-6 Installation Overview 12. Connect cables: keyboard, mouse, monitor, network, and power cables. See Cabling Guidelines for Compaq ProLiant 3000 Servers. 13. Turn on the computer and insert the SmartStart and Support Software CD to configure and manage the server. When the server boots from the SmartStart program, it automatically starts the System Configuration Utility. See Chapter 5 for detailed information. 14. Order Activation Keys. 15. Register your server.
2-7 For complete details on the SmartStart program, read the SmartStart installation card included in your SmartStart package. After the SmartStart program has finished configuring your system, installation of your new Compaq server is complete. ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: C-CH02.
3-1 Chapter 3 Rack-Mount Server Installation This chapter covers the following information: ■ How to attach the mounting hardware to the server and to the rack ■ How to install the server into the rack You may choose Compaq’s optional installation service to install your rack products. See “Optional Installation Service” at the end of this chapter.
3-2 Rack-Mount Server Installation WARNING: To reduce the risk of personal injury or damage to the equipment, at least two people are needed to safely unload the rack from the pallet. An empty 42U rack weighs 253 LB (115 kg), is over seven ft (2.1m) tall, and may become unstable when being moved on its casters. Do not stand in front of the rack as it rolls down the ramp from the pallet, but handle it from the sides.
3-3 Rack Temperature Requirements The operating temperature inside the rack will always be higher than the room temperature, and is dependent on the configuration of equipment in your rack. The TMRA for each piece of equipment should be checked before installation.
3-4 Rack-Mount Server Installation Airflow Requirements Compaq ProLiant rackmountable servers draw cool air in through the front door and exhaust warm air out the rear. Therefore, the front door of the rack must be adequately ventilated to allow ambient room air to enter the cabinet, and the rear door must be adequately ventilated to allow the warm air to escape from the cabinet. Do not block the ventilation apertures.
3-5 Unpacking the Server Unpack the server box and locate the materials and documentation necessary to install your rack-mountable server. Locating Materials and Documentation All of the equipment needed to install the ProLiant 3000 server in the rack is included with the rack and with the server 2 1 3 7 6 4 5 Figure 3-1.
3-6 Rack-Mount Server Installation Contents of the rack model server box include ■ Compaq ProLiant 3000 server ■ Cables - see Cabling Guidelines for Compaq ProLiant 3000 Servers ■ Rack mounting hardware (numbers reference Figure 3-1) 1 One pair slide rail mounting brackets 2 One pair 26-inch slide rail assemblies 3 Cable management arm bracket 4 Cable management arm 5 Cable management arm screws 6 Plastic rail covers (2) ❏ ■ Cable management arm support bracket Template that can be use
3-7 In addition to these supplied items, you may need: ■ Torx T-15 screwdriver ■ Phillips screwdriver ■ Slotted screwdriver ■ Application software diskettes, such as SmartStart ■ Options to be installed, such as ❏ Optional uninterruptible power supply (UPS) ❏ Optional monitor, keyboard, etc. ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: D-CH03.
3-8 Rack-Mount Server Installation Preparing the Mounting Brackets and Slide Rail Assemblies Each pair of mounting brackets, with attached slide rail assemblies, supports one rack-mountable server. Figure 3-2. Rack mounting brackets; alignment tabs identify the front flanges Each slide rail assembly consists of an outer bracket rail and an inner component rail (see the following figure).
3-9 Figure 3-3. Slide rail assembly (outer bracket rail and inner component rail) IMPORTANT: To make the installation of the mounting bracket easier, attach the bracket rail to the rack mounting bracket before attaching the mounting bracket assembly to the rack. This way, the joined mounting bracket and bracket rail can be fastened to the rack as one assembly. Attaching the Bracket Rail to the Mounting Bracket Please read all of the following eight steps before you begin. 1.
3-10 Rack-Mount Server Installation Figure 3-4. Removing the component rail from the bracket rail 3. Put the component rails to one side. You will attach them to the rack server chassis later, in the section, "Attaching Component Rails to the Server." The next figure shows the separated bracket rail with its inner sliding piece and the flat, one-piece component rail. Figure 3-5.
3-11 The bracket rail consists of a fixed outer rail that screws to the rack mounting bracket, and an inner slide on a steel ball bearing movement. This inner slide does not detach. Figure 3-6. Bracket rail with inner slide. The front of the rail is highlighted. 4. Lay the bracket rail inside the mounting bracket with the front of both pieces oriented in the same direction. Align the front screw holes in the mounting bracket and the bracket rail.
3-12 Rack-Mount Server Installation 5. Extend the inner slide from the front of the bracket rail. With this piece extended, you will see two screw holes aligned in the mounting bracket and the bracket rail. These are the two exposed holes near the back end of the bracket rail and the front hole accessible through a slot in the inner slide. 6. Fasten the bracket rail to the mounting bracket with one 8-32 x 1/4-inch slotted screws. (Do not use nuts or washers with the screws.
3-13 1 2 3 2 2 26 Figure 3-7. Attaching the bracket rail to the mounting bracket You will use a total of four 8-32 x 1/4-inch slotted screws to fasten the bracket rail to the mounting bracket. When all five screws are fastened, the mounting bracket and bracket rail form a mounting bracket slide assembly that you will attach to the rack. 8. Repeat steps 4 through 7 with the other bracket rail and mounting bracket. You now have a pair of mounting bracket slide assemblies to be attached to the rack.
3-14 Rack-Mount Server Installation Attaching the Mounting Bracket Slide Assembly to the Rack WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that the rack leveling feet are extended to the floor and support the full weight of the rack. Each rack must be level and stable. Racks that are not coupled together require the installation of stabilizers. This must be done before you perform any work on the rack.
3-15 IMPORTANT: The template is two-sided (front and back) and printed with arrows that show you where the screws will be inserted, both for the mounting bracket assemblies and for the thumbscrews that will secure the server's face plate to the front of the rack. Align the template carefully with the holes on the rack, to determine the exact placement of the screws. 2. When you mark the positioning of the mounting bracket screws, also mark the positioning in the front of the rack for the cage nuts.
3-16 Rack-Mount Server Installation Figure 3-8. Measuring with the template 3. After marking the front of the rack, turn the template over and mark the back rails of the rack. Open the rear door of the rack to access the back rails. 4. On the back of the rack, mark the rail to show the top of the template. This will help you align a template for the next component.
3-17 3. Insert the tip of the fitting tool through the other side of the perforation and hook the opposite lip of the cage nut. Figure 3-9. Inserting cage nuts 4. Using the fitting tool as a lever, pry the cage nut into position. 5. Repeat for each cage nut. Attaching the Mounting Bracket Assembly to the Rack The tabs on the front of the mounting bracket help to align it with the front of the rack frame. Cage nuts are not used for the front attachment of the mounting bracket.
3-18 Rack-Mount Server Installation 1. Attach a mounting bracket assembly to the front of the rack first, using one M6 x 1.0-12L Phillips screw in the bottom hole of the bracket. Do not use the washers supplied with the Compaq rack. IMPORTANT: Use only the bottom hole of the bracket as shown in Figure 3-10 Figure 3-10. Attaching mounting bracket assembly to the front of the rack 2. Carefully align the mounting bracket assembly with the rear rack frame. 3.
3-19 Top View CZR4-012.eps Figure 3-11. Cage nut and back of mounting bracket assembly installed 4. After attaching both mounting bracket assemblies to the rack, prepare the server for mounting in the rack. ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: D-CH03.
3-20 Rack-Mount Server Installation Attaching Component Rails to the Server 1. Place the tab on a component rail at the front of the server chassis. The holes in the component rail will line up only one way with the chassis. 2. Attach the flat side of a component rail to each side of the server chassis with five 8-32 x 1/4-inch Phillips screws. Do not use washers with the screws. Figure 3-12.
3-21 Attaching the Cable Management Arm Bracket The cable management arm bracket fastens to the top right rear of the rack server's chassis. The bracket provides an attachment point for the cable management arm from the server to the rear frame of the rack. Attach the cable management arm bracket to the back of the server with two 6-32 x 1/4 Phillips screws. Attach the rack rail covers to the rack. Figure 3-13.
3-22 Rack-Mount Server Installation Loading the Rack Server Load and secure the server to the rack with the face plate thumbscrews before continuing to attach any more mounting bracket assemblies. Ensure that this pair of brackets is perfectly aligned and installed and that the server fits before you continue. WARNING: To reduce the risk of personal injury or damage to the equipment, a minimum of two people MUST lift the server into the rack. The server weighs 50 pounds (22.6 kilograms).
3-23 1. Pull the slide rails forward from the mounting brackets. 2. Carefully align the server's component rails with the rack's slide rails and slide the server into the rack. CAUTION: Be sure to keep the component parallel to the floor when sliding the component rails into the slide rails. Tilting the component up or down could result in damage to the rails. Figure 3-14.
3-24 Rack-Mount Server Installation WARNING: To reduce the risk of personal injury, be careful when pressing the component rail release latches and sliding the component into the rack. The slide rails could pinch your fingertips. 3. Depress the component rail release latch on either side of the server and slide the server into the rack. IMPORTANT: The first time you slide the component into the rack, you may have to apply some pressure.
3-25 1. For easier handling, first slide the server into the rack, then attach the cable management arm to the cable management arm bracket. If you attach the arm before loading the server in the rack, the arm may swing around and interfere with the loading process. 2. After you have loaded the server into the rack, attach one end of the cable management arm to the server's cable management arm bracket using two M6 x 1.0-12L Phillips screws. Align the arm to the bracket as shown in the following figure.
3-26 Rack-Mount Server Installation Figure 3-16. Attaching the cable management arm to the rear brace of the rack Attaching the Optional Cable Support The optional cable support attaches to both sides of the rack’s rear. All cables to and from the server are tied to this support, which allows the server cables to stretch from the right rear of the server across to the cable channel on the other side of the rack, where the other cables are all bundled in the cable channel.
3-27 Figure 3-17. Attaching the cable support to the rack Optional Installation Service The installation service covers the entire hardware installation from unpacking the components to routing the cables and running a test of the system. In the United States, Compaq will make all of the arrangements to have the rack system installed by qualified Guaranteed Service Providers. An order form with pricing is available from PaqFax, the Compaq fax retrieval service.
4-1 Chapter 4 Installing Hardware Options This chapter is divided into two major parts as follows: ■ ■ Accessing Non Hot-Plug Areas - you must shut down the server power in order to install options, upgrades or replacements in the following areas: ❏ Processor boards and sockets ❏ Memory board and sockets ❏ System Board ❏ Drive Cage Backplane Board ❏ Power Supply Backplane Board ❏ Three shared PCI/EISA slots ❏ Five PCI slots ❏ Fans Accessing Hot-Plug Areas - you can install hot-plug optio
4-2 Installing Hardware Options Accessing Non Hot-Plug Areas To install options, upgrades or replacements in these areas, you must first shut down the server power. Accessing Processors, Memory Board, and System Board WARNING: To reduce the risk of injury from electrical shock, remove all power cords to completely disconnect power from the system. WARNING: To reduce the risk of electric shock or damage to the equipment: ■ Do not disable the power cord grounding plug.
4-3 1. Back up your server data. 2. Shut down the operating system in an orderly manner as directed in your operating system instructions. 3. Power down the server and remove the power cord. IMPORTANT: The system power in the ProLiant 3000 server does not completely shut off with the front panel Power On/Standby switch. The two positions of the switch functions as ON and STANDBY, rather than ON and OFF.
4-4 Installing Hardware Options 6. Slide the side cover toward the rear of the unit about 1 inch (2.5 cm); then remove the cover. NOTE: When you remove the access panel, the interlock switch removes power from the system. Figure 4-1. Removing the server cover Accessing the Processor NOTE: To allow easier access, you can tilt the server on the right side (side opposite the removed panel). Be sure to lock the casters if you do tilt the server.
4-5 1 2 Figure 4-2. 2. 1 Removing the terminator board To install a Pentium II processor board, follow the instructions included in the processor option kit to install the processor on the board. then see Figure 4-3. Figure 4-3. Installing the Pentium II processor board ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-6 Installing Hardware Options Accessing Other System Board Components With the top panel and processor boards removed, as described in the previous steps, you should be able to locate and identify the System Board components shown in Figure 4-4. 1 2 3 4 5 6 7 8 13 12 29 28 14 15 16 17 18 19 20 21 22 9 Figure 4-4.
4-7 System Board Switches The following table defines the six switches on the system board. The Open (OFF) position is the default configuration for each switch.
4-8 Installing Hardware Options Removing the memory board Figure 4-5. 2. Install DIMMs as shown in Figure 4-6. For information on memory banks, see the following section titled “Memory Banks.” 2 1 2 Figure 4-6. Latching DIMMs Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-9 3. Install the memory board as shown in Figure 4-7. Figure 4-7. Installing memory board Memory Banks In the Compaq ProLiant 3000 server, DIMM sockets are grouped in banks of two adjacent sockets. When you add memory, you must add a bank at a time. Memory banks on the system board and on the memory board are identified in Figure 4-8 and Figure 4-9 respectively. Memory banks are also identified on a label on the inside of the access panel.
4-10 Installing Hardware Options Bank 1 Bank 2 J1 J2 Figure 4-8. J12 J11 J10 J9 J8 J7 J6 J5 J3 J4 Memory banks on the system board Bank 6 Bank 5 Bank 4 Bank 3 Note: Both sockets in a memory bank must be populated. Figure 4-9. Memory banks on the memory board Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-11 For the best performance, DIMM banks should be added in the following order: First: Bank 3 (as shipped) Bank 1 (system board) Bank 4 (memory board) Bank 2 (system board) Bank 5 (memory board) Last: Bank 6 (memory board) Accessing the Drive Cage Back Plane These instructions cover the removal of the hot-plug SCSI drive and removable media cage, removal of the Simplex Enable board, and installation of the Duplex Enable board. This procedure enables controller duplexing of the internal SCSI drives.
4-12 Installing Hardware Options 2. Remove the fans and set them aside. You should not have to remove the cables to the fans. CAUTION: Never power up the server if both fans have been removed from either the processor or I/O section. Overheating and damage to hardware could result. 2 1 Figure 4-10. Removing a fan Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-13 3. Unlock the server, open the front panel, and slide the front panel up and away from the server. Figure 4-11. 4. 5. Removing the front panel Loosen the thumbscrews on the front of the drive cage. Pull out the latch at the back of the drive cage (shown in Figure 4-13) and pull out the drive cage 2 to 3 inches to allow better access to cables. ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-14 Installing Hardware Options Figure 4-12. Partially pull out the drive cage Figure 4-13. Drive cage latch 6. Remove all cables from the back of the drive cage except for the removable media power cable. 7. Completely remove the drive cage. Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-15 If you have removed the drive cage in order to install the Duplex Enable board, procedure with the next topic, “Installing the Duplex Enable Board Option.” Otherwise, skip to step 8. Installing the Duplex Enable Board Option Be sure you have followed all the steps under “Accessing the Drive Cage Back Plane” before proceeding with the following steps. a) Remove the Simplex Enable board from the back of the drive cage. Figure 4-14.
4-16 Installing Hardware Options b) Insert the Duplex Enable board. Figure 4-15. Installing the duplex enable board CAUTION: The SCSI backplane board must have either a Duplex Enable board or a Simplex Enable board installed in order for the SCSI bus to be terminated properly. If neither of these boards is installed, the service LEDs of all drives will light as a warning. 8. Replace the drive cage. Do not push it back fully until after you install cables (Shown in Figure 16).
4-17 Figure 4-16. Re-installing the drive cage ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-18 Installing Hardware Options 9. Reconnect the SCSI cables on the back of the drive cage. Refer to Figure 4-19 connector identification. Refer to Cabling Guidelines for Compaq ProLiant 3000 Servers for information on SCSI cabling. Hard Drive Backplane Connector SCSI Input 1 SCSI Input 0 Removable Media Connector Figure 4-17. Connectors on back of drive cage 10. Pull out the drive cage latch and push the drive cage back fully until the drive cage latch can be pushed into place. 11.
4-19 Figure 4-18. Example cable connection to SCSI controller 13. Replace fans. Replacing the Side Access Panel Reverse the steps from the “Accessing Processors, Memory Board, and System Board” procedure to replace the side access panel. ProLiant 3000 Setup and Installation Guide Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-20 Installing Hardware Options Interlock System The interlock system prevents power distribution throughout the system if any of the following conditions exist: 1. Top access panel not installed 2. Side access panel not installed 3. Processor or terminator card not fully installed or not properly seated If any one or more of the above conditions are not met, the main power supply output is disabled; however, auxiliary power still remains in the exposed areas.
4-21 Accessing DIMM Sockets on the System Board WARNING: Before removing the top panel, ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet. To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them. CAUTION: To prevent loss of data or damage to the equipment, place the system in STANDBY before removing the side access panel.
4-22 Installing Hardware Options 3. Install DIMMs. You must add memory by bank, that is, a set of 2 EDO buffered DIMMs at a time. Each bank should contain DIMMs of the same size. For more information on banks, see the section titled “Memory Banks” earlier in this chapter. 2 1 2 Figure 4-20. Installing system board DIMM banks Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-23 Accessing Hot-Plug Areas This section describes accessing the following areas: ■ Hot-Plug SCSI Drives ■ Hot-Plug Power Supplies Components in these areas have color coded latches or levers to signify that they are hot-plug devices. Accessing the Hot-Plug SCSI Drives 1 2 3 Figure 4-21. NOTE: Removing a SCSI drive Pinch both sides of drive levers to unlock, then swing the levers out.
4-24 Installing Hardware Options 2 1 Figure 4-22. Installing a SCSI drive IMPORTANT: If the drive cage is configured for simplex mode (PassThru board installed) and you are using 1-inch drives, do not use drive bay 7 (see Figure 4-25). If you install a drive in bay 7, the service LED for that drive will light and the drive will be inaccessible. Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: E-CH04.
4-25 SCSI ID Numbers There are four possible numbering schemes depending on whether you are using 1-inch height drives, 1.6-inch height drives, simplex controller, or duplex controllers. The following four figures illustrate these four schemes. IMPORTANT: The Simplex Enable board must be installed on the back of the drive cage for the simplex modes and the Duplex Enable board must be installed for the duplex modes. Figure 4-23.
4-26 Installing Hardware Options SCSI Channel A or Channel B Figure 4-24. 3 6 1 5 0 4 SCSI ID Numbers - Single SCSI Channel (Simplex Mode) with 1.6-inch drives SCSI Channel A SCSI Channel B 3 3 2 2 1 1 0 0 Figure 4-25. SCSI ID Numbers - Dual SCSI Channels (Duplex Mode) with 1-inch drives SCSI Channel A SCSI Channel B 3 3 1 1 0 0 Figure 4-26. SCSI ID Numbers - Dual SCSI Channels (Duplex Mode) with 1.
4-27 Pre-Failure Warranty The Compaq ProLiant 3000 server includes Pre-Failure Warranty for Pentium II processors, hard drives, power supplies, and DIMMs purchased from Compaq through an Authorized Compaq Reseller. Supported components are eligible for replacement under this warranty before they actually fail, if the system determines that these components have degraded below predetermined reliability thresholds within the product warranty period.
5-1 Chapter 5 Server Configuration and Utilities This chapter describes the tools that Compaq provides to assist you in the configuration and management of your Compaq ProLiant 3000 Server. Configuring the Server with SmartStart SmartStart is the intelligent way to configure the server and to load the system software, thereby achieving a well-integrated server to ensure maximum dependability and supportability.
5-2 Server Configuration and Utilities Figure 5-1. 3. Inserting the CD-ROM When the busy indicator turns on, the drive is ready to receive commands and data may be retrieved from the disc. Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: F-CH05.
5-3 Using the System Configuration Utility The Compaq System Configuration Utility performs a wide range of configuration activities, including: ■ Automatically configuring PCI and ISA Plug and Play boards ■ Providing switch and jumper settings ■ Resolving resource conflicts in areas such as memory, port addresses, and interrupt requests (IRQ) ■ Managing the installation of mass storage devices such as hard drives, tape drives, and diskette drives ■ Setting and storing power-on features like date
5-4 Server Configuration and Utilities For PCI boards, the utility reads the configuration options from the PCI board's configuration space from a PCI configuration file (.PCF). ■ Compaq Option Configuration Files diskette ■ Non-Compaq Option Configuration Files diskette ■ SmartStart and Support Software CD The .CFG file provides board resource requirements and switch and jumper setting alternatives.
5-5 Starting the System Configuration Utility To start the Compaq System Configuration Utility for the first time, refer to the SmartStart Installation poster. After the first time, access the System Configuration Utility as follows: 1. Press the Ctrl+Alt+Del keys to reboot the server. 2. When the following prompt appears at the top of the screen during Power-On Self-Test (POST), press the F10 key.
5-6 Server Configuration and Utilities System Configuration Utility Main Menu This overview of the main menu options overview explains how to access the main menu and how to set the power-on features. The following options are available from the main menu: ■ System Configuration - Takes you through the configuration process step-by-step. Select the System Configuration option when a configuration change is required.
5-7 Configuring Hardware When you select the Configure Hardware menu, a screen with five steps is displayed. Below is a listing of each step with a brief explanation. Step 1: Important System Configuration Information This step provides an overview of the configuration process. Step 2: Add or Remove Boards Use this step to add the PCI or EISA boards to the configuration or remove any boards from the configuration. Step 3: View or Edit Details Use this step to make necessary configuration changes.
5-8 Server Configuration and Utilities Setting Power-On Defaults You can set and change the Power-On features at any time. 1. Select System Configuration from the Main Menu; then select Power-On Defaults. 2. Set the current date in the format: MM-DD-YYYY 3. Set the correct time in the format: HH:MM:SS 4. Set the Power-On Num Lock state: ( ) OFF (*) ON * This activates the numeric keypad when the computer is turned ON.
5-9 Creating a New System Partition If you used SmartStart to configure your server and install your operating system, this procedure (“Creating a New System Partition”) was done automatically for you. Use this procedure only if the operating system was not installed on the server and you wish to create a system partition. 1. Insert the Compaq SmartStart and Support Software CD in the CDROM drive and turn on the server.
5-10 Server Configuration and Utilities Verifying the System Partition To verify that the system partition exists, follow this procedure: 1. Remove any media from the CD-ROM drive and the diskette drive. 2. Reboot the system by pressing Ctrl+Alt+Del or by turning the server OFF and then ON again. 3. Press the F10 key when the following prompt appears. Press "F10" key for System Partition Utilities IMPORTANT: The text appears for only two seconds.
5-11 Configuration Backup The Configuration Backup option allows you to create a backup of the system configuration and to restore the system configuration from the backup. The following menu options are available: ■ Backup ■ Restore Configuration Backup and Configuration History Files When you save and exit the System Configuration Utility, the utility keeps a history of the configuration.
5-12 Server Configuration and Utilities Table 5-1 System Configuration History Log Files Filename Description SYSTEM.SCI Current configuration information SYSTEM1.SCI Previous configuration information SYSTEM2.SCI Previous configuration information (oldest) SYSTEM.CHL Textual representation of SYSTEM.SCI file SYSTEM1.CHL Textual representation of SYSTEM1.SCI file SYSTEM2.CHL Textual representation of SYSTEM2.
5-13 Configuring PCI Boards Automatically The system ROM automatically configures PCI boards. If a user selection is required, a POST message directs you to run the System Configuration Utility. Also, you may use the System Configuration Utility to change the default automatic settings. Removing Boards System ROM automatically reconfigures the server after a PCI board or DIMM is removed.
5-14 Server Configuration and Utilities Not all operating systems ship with each server. Consult your local reseller or Compaq Customer Service to get a SmartStart pack with additional operating system support. Some operating systems have driver support/updates but not an integrated SmartStart installation. You can still configure your server and manually install your operating system.
5-15 Loading Compaq Device Drivers Drivers are located on the Compaq SmartStart and Support Software CD. IMPORTANT: Always check README files on the SmartStart and Support Software CD. If present, these files may contain information about important software updates. Novell NetWare Device Drivers form Compaq Your server must have certain device drivers to operate using NetWare. These drivers are located on the Compaq SmartStart and Support Software CD shipped with the server.
5-16 Server Configuration and Utilities Microsoft Windows NT Device Drivers from Compaq Drivers are supplied to support Windows NT 3.51 and 4.0. They are located on the SmartStart and Support Software Diskette CD, and some of the drivers are contained on the Windows NT retail product. These drivers are also located on the Compaq SmartStart and Support Software CD. The drivers on the SSD may be newer versions with new functionality, problem fixes, and so on.
5-17 SCO OpenServer and SCO UnixWare Device Drivers from Compaq Your server must have certain device drivers to operate under the SCO OpenServer and SCO UnixWare 2.1 operating systems. These drivers are located on the Compaq SmartStart and Support Software CD shipped with the server. If you use SmartStart to install your operating system, these drivers will be installed automatically.
5-18 Server Configuration and Utilities Manual installation If you choose not to let SmartStart configure the server, follow this procedure: 1. Insert the Compaq SmartStart and Support Software CD into the CDROM drive. 2. Boot your system. 3. Select Non-SmartStart Setup. 4. Follow the instructions that display on the monitor. IBM OS/2 Device Drivers from Compaq Your server must have certain device drivers for some server options to operate using IBM OS/2 Warp Server 4.0, IBM OS/2 Warp Server 4.
5-19 Banyan VINES Device Drivers from Compaq Your server must have certain device drivers for some server options to operate using the Banyan VINES operating system. Compaq provides driver support for Banyan VINES 6.00 and above, including the new VINES 7.00. These drivers are located on the Compaq SmartStart and Support Software CD you received with your server. You can use SmartStart to create a Banyan VINES Support Software Diskette (SSD) from Compaq to support a manual installation of Banyan VINES.
5-20 Server Configuration and Utilities Diagnostics and Other Utilities ■ When you select the Diagnostics and Utilities feature from the System Configuration Utility main menu, the utility provides prompts to test, inspect, upgrade, and diagnose the server. ■ Diagnostics and Utilities are located on the system partition on the hard drive and must be accessed when a system configuration error is detected during the Power-On Self-Test (POST).
6-1 Chapter 6 Integrated Management This chapter contains instructions and guidelines for using the Integrated Management features in Compaq ProLiant 3000 servers that may not be familiar to you. Subjects covered are: ■ Integrated Management Display ■ Integrated Management Log Integrated Management Display The Compaq Integrated Management Display (IMD) is an integrated, 16x4 character display mounted on the front of the server.
6-2 Integrated Management If there are no errors, you will see the Idle Screen Text. Figure 6-1 shows the default screen, but this screen could be different if you changed the text during configuration. COMPAQ PROLIANT 3000 ESC Figure 6-1. Idle Screen Text Writer: Tom Erber Project: ProLiant 3000 Setup and Installation Guide Comments: 296908-002 File Name: G-CH06.
6-3 Navigation Buttons To navigate through the menus, use the four buttons shown in Figure 6-2. The Up and Down arrow keys ( and ) allow you to move through the menu screens and choose menu items. The right button ( ) acts as an Enter key and allows you to travel down through the menus. The left button ( ) acts as an Escape key and allows you to travel back up the menu. ESC 1 3 4 2 Figure 6-2.
6-4 Integrated Management Display Symbols There are three different display symbols used to indicate your options as you scroll through the menus. These on screen symbols are the Up and Down arrows, and the Selector arrow. Table 6-1 Integrated Management Display Symbols Type of Symbol Symbol Meaning Arrow Selector arrow shows current menu item. Press Enter on the IMD to select the menu item to the right of this arrow. Up Arrow If present in upper right corner, indicates previous information exists.
6-5 System Behavior with Error Events After system POST, if there is an F1 error condition, the IMD flashes this message: LCD-013.EPS !ALERT! Press Any Key to View New Events ESC Figure 6-3. New Event Message At this point you must scroll through each screen of the event information menu before the IMD will allow you to move on to other menu choices. The display will not allow you to escape out of the Unviewed Events section until you have examined all of the information stored here.
6-6 Integrated Management Menu Structure The following outline shows the structure of each menu and submenu in the order in which it appears: Events Event List Administration Information ■ ■ ■ ■ Server ❏ Server Name ❏ Asset Tag ❏ Operating System ❏ Other Administrator ❏ Name ❏ Phone ❏ Pager ❏ Other Service ❏ Name ❏ Phone ❏ Pager ❏ Other Custom Menu Item (if entered) ❏ Custom Menu Screen (if entered) System Information ■ ■ ■ ■ ROM Date BootBlock Date Memory Processors Contrast ■ ■ Contrast Other
6-7 Integrated Management Log The Compaq Integrated Management Log (IML) records system events and stores them in an easily-viewable form. The IML records hundreds of events instead of the 16 events that the Critical and Correctable Error Logs are capable of recording. The IML also marks each event with a time-stamp with one-minute granularity, instead of the one-hour granularity of the previous logs.
6-8 Integrated Management Multiple Ways of Viewing the Log You can view an event in the Integrated Management Log in several ways: ■ On the Integrated Management Display ■ From within Compaq Insight Manager ■ From within Compaq Survey Utility ■ Using the IML Management Utility, a DOS program located on the Compaq SmartStart and Support Software CD.
6-9 Viewing the Event List 1. From Compaq Insight Manager, select the appropriate server, then select View Device Data. The selected server is displayed with buttons around its perimeter. 2. Select the Recovery button. 3. Select Integrated Management Log. NOTE: You can only view the list from the Recovery/Integrated Management screen. To print the list, follow the instructions below. 4. If a failed component has been replaced, select the event from the list; then select Mark Repaired.
6-10 Integrated Management Compaq Survey Utility The Compaq Survey Utility is a serviceability tool available for Windows NT and Novell NetWare that delivers on-line configuration capture and comparison to maximize server availability. It is delivered on the Compaq Management CD in the Server Setup and Management package, or is available on the Compaq web site. Refer to the Compaq Management CD for information on installing and running the Survey Utility.
6-11 List of Events The event list displays the affected components and the associated error messages. Though the same basic information is displayed, the format of the list may be different depending on how you are viewing it: on the Integrated Management Display, from within Compaq Insight Manager, or from within the Compaq Survey Utility.
6-12 Integrated Management Table 6-2 Event Messages Event Type Event Message Machine Environment Fan Failure System Fan Failure (Fan X, Location) Fan Inserted System Fan Inserted (Fan X, Location) Fan Removed System Fan Removed (Fan X, Location) Fans Not Redundant System Fans Not Redundant Overheat Condition System Overheating (Zone X, Location) Main Memory Correctable Error threshold exceeded Corrected Memory Error threshold passed (Slot X, Memory Module X) Corrected Memory Error threshold p
6-13 Event Messages continued Event Type Event Message POST Error: Error message POST Error Power Subsystem Power Supply Failure System Power Supply Failure (Power Supply X) Power Supply Inserted System Power Supply Inserted (Power Supply X) Power Supply Removed System Power Supply Removed (Power Supply X) Power Supply Not Redundant System Power Supplies Not Redundant System Configuration Battery Low Real-Time Clock Battery Failing Power Module Failure A CPU Power Module (System Board, Socket
A-1 Appendix A Power Cord Set Requirements The power cord set meets the requirements for use in the country where you purchased your equipment. The voltage selection switch allows you to select the appropriate line voltage for your server. Power cord sets for use in other countries must meet the requirements of the country where you use the server. For more information on power cord set requirements, contact your Authorized Compaq Dealer.
A-2 Power Cord Set Requirements Country-Specific Requirements Use the following table to identify the appropriate accredited agency in your country. Table A-1 Power Cord Set Requirements - By Country Country Australia Austria Belgium Canada Denmark Finland France Germany Italy Japan Norway Sweden Switzerland United Kingdom United States Notes: Accredited Agency EANSW OVE CEBC CSA DEMKO SETI UTE VDE IMQ JIS NEMKO SEMKO SEV BSI UL Applicable Note Numbers 1 1 1 2 1 1 1 1 1 3 1 1 1 1 2 1.
B-1 Appendix B Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
B-2 Regulatory Compliance Notices Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
B-3 Declaration of Conformity for Products Marked with FCC Logo, United States Only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding this declaration, contact: Compaq Computer Corporation P. O.
B-4 Regulatory Compliance Notices Canadian Notice(Avis Canadien) Class B Equipment This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
B-5 Japanese Notice Australian Notice This customer equipment is to be installed and maintained by service personnel as defined by AS/NZS 3260 Clause 1.2.14.3. Service Personnel. Incorrect connection of connected equipment to the General Purpose Outlet could result in a hazardous situation.Safety requirements are not fulfilled unless the equipment is connected to a wall socket outlet with protective earth contact.
B-6 Regulatory Compliance Notices Laser Devices The CD-ROM drive contains a laser device. All Compaq systems equipped with a laser device comply with safety standards, including International Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product.
B-7 Laser Product Label The following label or equivalent is located on the surface of your CD-ROM drive. This label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This label appears on a laser device installed in your product. Laser Information Laser Type Semiconductor GaAIAs Wave Length 780 nm +/- 35 nm Divergence Angle 53.5 degrees +/- 0.5 degrees Output Power Less than 0.2 mW /10,869 W·m sr -2 Polarization Circular 0.25 Numerical Aperture 0.45 inches +/- 0.
B-8 Regulatory Compliance Notices Battery Replacement Notice Your computer is provided with a battery powered Real-Time Clock circuit. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by a Compaq Authorized Service Provider using the Compaq spare designated for this product.
C-1 Appendix C Internal CD-ROM Drive The Internal CD-ROM drive is a random access, read-only storage device capable of retrieving data from removable compact disc media, which can store up to 680 Mbytes of digital information. 1 Figure C-1.
Index-1 Index . .CFG files 5-3 .
Index -2 adding 4-22 banks 4-22 removing 5-13 Disassembly 4-1 Diskette drive 1-3 Display Symbols, IMD 6-4 Drive cage connectors 4-18 removal 4-11 Drivers See Device drivers Duplex board installation 4-11 installing 4-15 E EISA slots 1-2 Error Events, IMD 6-5 Expansion slots general 1-2 F Fault tolerance 1-7 Features, ProLiant 6500 1-1 Fitting tool for cage nuts 3-16 Floppy drive See Diskette drive G Getting Help xii H Hard drives configuration 1-10 general 1-3 Pre-Failure Warranty 4-27 Hardware, config
Index-3 Integrated Management Log 6-5 Integrated Remote Console 1-9 Interlock switch 4-4 system 4-20 Interlock switch features 1-11 Internal CD-ROM C-1 IRC See Integrated Remote Console Network interface controller (NIC) 1-2 Normal Run-time Behavior 6-1 O L2 cache memory 1-2 Laser Devices B-5 Logs, Server Health 1-6 Online help xii Operating system installing 5-13 SMP 5-14 Operation of advanced features 6-1 Option configuration files See .
Index -4 IMD messages 6-1 operations 6-1 Power-on, setting defaults 5-8 Pre-Failure Insight Manager alert 4-27 Warranty 4-27 Processor accessing 4-2 boards 1-1 Pre-Failure Warranty 4-27 Product Safety Information x R Rack attaching component rail to server 3-20 cable management arm bracket 3-21 cable support for server 3-26 inserting cage nuts 3-16 installation video 3-1 installing mounting bracket 3-17 installing rack model server 3-1 loading server 3-22 locating materials 3-5 Planning and Installation G
Index-5 CD 5-1 creating system partition 5-9 device drivers for Banyan VINES 5-19 for IBM OS/2 5-18 for Novell NetWare 5-15 for SCO 5-17 for Windows NT 5-16 starting from System Configuration Utility 2-6, 2-7 SMP operating system support 5-14 Spinning bar, IMD 6-1 Storage devices 1-3 Symbols IMD 6-4 in text x on equipment x Symbols in Text x System board, accessing 4-2 board, components 4-6 creating partition 5-9 management features 1-4 partition 5-8 partition upgrading 5-10 partition verifying 5-10 System
