ProLiant 6500 Setup and Installation Guide For Pentium II Xeon and Pentium III Xeon Processor-based Servers Second Edition (February 1999) Part Number 328196-002 Compaq Computer Corporation
Notice The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
iii Contents About This Guide How this Guide is Organized ....................................................................................................... x Text Conventions ........................................................................................................................ xi Symbols in Text.......................................................................................................................... xii Symbols on Equipment ...........................................
iv Compaq ProLiant 6500 Features continued Server Management Features and Configuration Tools ........................................................... 1-9 Compaq SmartStart .......................................................................................................... 1-10 Compaq System Configuration Utility ............................................................................ 1-10 Compaq Operating System Utilities ........................................................................
v Rack-Mountable Server Installation continued Preparing the Rack-Mounting Brackets and Slide Rail Assemblies....................................... 2-13 Attaching the Bracket Rail to the Rack-Mounting Bracket............................................. 2-14 Attaching the Slide Rail Assembly to the Rack............................................................... 2-19 Attaching the Rack-mounting Bracket Assembly to the Rack ........................................
vi Integrated Management Log continued Navigating the Menus ............................................................................................................... 4-9 Normal Run-time Behavior................................................................................................ 4-9 Navigation Buttons ............................................................................................................ 4-9 Display Symbols ...............................................................
vii Cabling Guidelines continued PCI Hot Plug Cabling.............................................................................................................. 6-25 IDE Removable Media Cabling .............................................................................................. 6-26 Power Cabling ......................................................................................................................... 6-27 Securing the Power Cords .................................................
viii Appendix C Switch Settings Maintenance Configuration Switch Functions (SW1) ............................................................. C-1 Core Frequency Switch (SW2 and SW3)................................................................................. C-2 Appendix D LEDs Interlock LEDs ......................................................................................................................... D-1 Network Interface Controller (NIC) LEDs .............................................
ix About This Guide IMPORTANT: This guide is for Pentium II Xeon and Pentium III Xeon processor-based servers only. This Compaq ProLiant 6500 Setup and Installation Guide is designed to be used as step-by-step instructions to set up your server for optimal performance, and as a reference for operation, troubleshooting, and future upgrades. This guide is for the person who installs, administers, and repairs servers.
x About This Guide How this Guide is Organized This guide describes the features, configuration, diagnostics, and technical specifications of your new server. The guide is divided into the following chapters: ■ Chapter 1 - Compaq ProLiant 6500 Features - provides an overview of the Compaq ProLiant 6500 server and its features. ■ Chapter 2 - Rack-Mountable Server Installation - outlines the initial Compaq ProLiant 6500 rack-mount installation.
xi Text Conventions This document uses the following conventions to distinguish elements of text: Keys Keys appear in boldface. A plus sign (+) between two keys indicates that they should be pressed simultaneously. USER INPUT User input appears in a different typeface and in uppercase. FILENAMES File names appear in uppercase italics. Menu Options, Command Names, Dialog Box Names These appear in initial capital letters. COMMANDS, DIRECTORY NAMES, and DRIVE NAMES These always appear in uppercase.
xii About This Guide Symbols in Text These symbols may be found in the text of this guide. They have the following meanings. ! WARNING: Indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Indicates that failure to follow directions could result in damage to equipment or loss of information. IMPORTANT: Presents clarifying information or specific instructions. NOTE: Presents commentary, sidelights, or interesting points of information.
xiii Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. ! Power Supplies or Systems marked with these symbols indicate the equipment is supplied by multiple sources of power.
xiv About This Guide Rack Stability ! WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that: ■ The leveling jacks are extended to the floor. ■ The full weight of the rack rests on the leveling jacks. ■ The stabilizing feet are attached to the rack if it is a single rack installations. ■ The racks are coupled together in multiple rack installations. ■ A rack may become unstable if more than one component is extended for any reason. Extend only one component at a time.
xv Using the Compaq Systems Reference Library CD The Compaq Systems Reference Library CD (SRL) provides a wide variety of user, reference, and integration information. The SRL contains additional details on Compaq technology and provides information such as modem documentation, maintenance instructions, technotes, and part numbers for ordering options or spares. You can use the full-text search to find the information you need quickly.
1-1 Chapter 1 Compaq ProLiant 6500 Features IMPORTANT: This guide is for Pentium II Xeon and Pentium III Xeon processor-based servers only. The Compaq ProLiant 6500 Server delivers high-performance, state-of-the-art Pentium II Xeon and Pentium III Xeon processor technology, reliability, and enhanced memory, with advanced high-availability features required for demanding data center environments and key server management technologies that further enhance availability.
1-2 Compaq ProLiant 6500 Features Figure 1-1.
1-3 Expansion Slots Six I/O expansion slots are available: ■ 5 64-bit PCI Hot Plug slots ■ ❏ Pre-installed Compaq NC3122 Dual 10/100 TX UTP Controller ❏ 4 available slots One shared 64-bit PCI/ISA slot NOTE: The ISA slot is for modem use only. PCI Hot Plug The PCI Hot Plug feature provides the ability to remove and replace, upgrade, and add PCI expansion boards without powering down the server. Any PCI board can be placed in a PCI Hot Plug slot.
1-4 Compaq ProLiant 6500 Features Internal Drive Bays The Compaq ProLiant 6500 Server can house up to 10 mass storage devices. Internal Hot-Plug Drive Bays The Compaq ProLiant 6500 Server supports one SCSI hard-drive cage that can be configured with seven 1.0-inch or five 1.6-inch form factor standard hotplug SCSI hard drives. Drives can be of any storage capacity but must be mounted on Compaq hot-plug drive trays.
1-5 These utilities are provided on the Compaq Support Software for Microsoft Windows NT 4.0 diskettes (NTSSD). For more detailed information, see the NTREADME.HLP file on Diskette 1. Future operating sytem support is planned for later release. System Power Supplies Management: Guidelines CAUTION: Unless operating at 220V, it may be necessary to make tradeoffs with respect to which options can be added and powered with the installed power supplies while still remaining redundant.
1-6 Compaq ProLiant 6500 Features For example, if the available capacity of the installed power supplies permits adding two processors, you have the option of adding: ■ two processors, or ■ one processor and three hard drives, or ■ up to six hard drives Memory Board Features ■ ECC Memory with single-bit error correction and detection down to a single DIMM, and multi-bit error detection down to the memory bank ■ Supports EDO-buffered, 60-ns or faster, refreshed DIMMs installed in sets of four (bank
1-7 Peripheral Board Features SCSI Dual-Channel Wide-Ultra SCSI-3 Controller Video ■ Integrated PCI Video Controller provides maximum resolution of 1280 x 1024, 256 color, non-interlaced ■ 2-MB video SGRAM standard ■ Supports SVGA, VGA, and EGA graphics resolution ■ Software upgradable firmware including diagnostics ■ ROMPaq Utility used to upgrade ROM ROM Supported External Interfaces ■ External SCSI ■ Serial (two connectors) ■ Video ■ Parallel ■ Keyboard ■ Mouse NOTE: Keyboard and
1-8 Compaq ProLiant 6500 Features Network Interface Controller (NIC) The Network Interface Controller (NIC) is a Compaq NC3122 Dual 10/100 TX UTP Controller in a PCI slot. Features of the controller include two RJ-45 connectors for 10BaseT or 100 TX Ethernet, PCI Hot Plug support, Fast Etherchannel support, redundancy and load balancing. The NIC supports full duplex Ethernet for up to 20 or 200 Mb/s aggregate bandwidth per port. 100 Mb/s Fast Ethernet meets high bandwith requirements.
1-9 ■ Server Management Features, also important aspects of high availability and discussed in the following Server Management Features and Configuration Tools section, are: ❏ Compaq Smart Start ❏ Compaq Insight Manager ❏ Compaq Remote Insight ❏ Compaq Integrated Remote Console ❏ Compaq Survey Utility Server Management Features and Configuration Tools Compaq offers an extensive set of management features and optional tools to support effective server management and configuration: ■ Compaq SmartS
1-10 Compaq ProLiant 6500 Features For information regarding SmartStart, see the Server Setup and Management pack included in the shipping box.
1-11 Compaq Operating System Utilities Compaq servers running Windows NT take advantage of several utilities that provide detailed information and offer special capabilities. ■ Compaq PCI Hot Plug Utility ■ Compaq Advanced Network Control Utility ■ Compaq Integrated Management Log Viewer ■ Power Down Manager ■ Compaq Integrated Management Log Utility ■ Compaq Power Supply Viewer These utilities are provided on the Compaq Support Software for Microsoft Windows NT 4.0 diskettes (NTSSD).
1-12 Compaq ProLiant 6500 Features The features of the Integrated Management Display include: ■ Flexibility - The Integrated Management Display rotates to support both tower and rack configurations.
1-13 For information regarding Compaq Insight Manager, see the Server Setup and Management pack shipped with your server. Compaq Integrated Remote Console When the Compaq ProLiant 6500 Server is equipped with an optional supported modem, you can perform a wide range of configuration activities using the Compaq Integrated Remote Console (IRC), a hardware-based remote console solution for enhanced out-of-band remote server manageability.
1-14 Compaq ProLiant 6500 Features Automatic Server Recovery-2 If there is a critical system failure, Automatic Server Recovery-2 (ASR-2) allows you to restart the server and page a designated system administrator. For more information, see the Server Reference Guide on the Systems Reference Library CD (SRL).
1-15 Maximum SCSI Configuration A maximum practical SCSI configuration optimizing performance and storage could include the following: ■ One network interface controller (NIC) ■ Dual Channel Wide-Ultra SCSI-3 Controller ■ Five Smart Array 3200 Controllers ■ Ten Compaq ProLiant Storage System/UE units ■ Eighty-eight 18.2 GB drives This configuration would yield a total storage capacity of 1.6 TB (Terabytes) [1601 GB].
1-16 Compaq ProLiant 6500 Features Security Features For detailed information regarding the security features listed below, see the Systems Reference Library CD included in the Reference Information pack shipped with your server.
1-17 Hardware Security These hardware security features are provided: ■ Power supply security bar with padlock and key kit ■ PCI Hot Plug access door lock with key to protect PCI expansion boards ■ Hot-plug fan access door lock with key to protect hot plug fans ■ Built-in interlock circuit on system, peripheral and memory boards which prevents power from being applied if critical system components are not correctly installed to prevent component damage.
1-18 Compaq ProLiant 6500 Features ❏ The Compaq Disk Drive Fault Tolerance feature provides many disk subsystem and memory system error correction fault-tolerance options. For more detail on this feature for Compaq servers, see the Server Reference Guide on the Systems Reference Library (SRL) CD. ❏ The following Redundant Array of Inexpensive Disks (RAID) types are supported with the use of any Compaq SMART Array Controller.
1-19 Warranty ■ Three-year parts, labor, and on-site Limited Warranty ■ Pre-failure warranty on processors, memory, hard drives, fans and power supplies ■ For additional service and support offerings, visit the Compaq website at www.compaq.com. Server Registration Registering your server provides Compaq with valuable information on server installation. This information helps Compaq serve your needs better now and in the future. Visit www.compaq.com/register to register your server.
2-1 Chapter 2 Rack-Mountable Server Installation Installation Choices Using the Compaq Optional Installation Service You may choose the optional installation service offered by Compaq to install your rack products. The installation service covers the entire hardware installation from unpacking the components to routing the cables and running a test of the system. In the United States, Compaq will make all of the arrangements to have the rack system installed by qualified Guaranteed Service Providers.
2-2 Rack-Mountable Server Installation Installation CDs When installing the server, see the Installing Rack Products CD included with your server. In addition to this CD, there are other CDs available: the Rack Builder Configuration CD and the Rack Information Library CD. These are part of the Rack Resource CD Kit and can be downloaded from the Compaq website at www.compaq.com.
2-3 ■ Rack Information Library CD This CD lets you view, search, and print documentation for Compaq racks and rack options. It also assists in the setup and optimization of your new Compaq rack to best fit the needs of your environment. Installation Overview A brief summary of the steps required to install your Compaq ProLiant 6500 Server follows. Detailed instructions for each of the steps are included in later sections of this chapter. ■ Select an appropriate site for your rack.
2-4 Rack-Mountable Server Installation ■ Turn on the computer and insert the SmartStart and Support Software CD to configure and manage the server. When the server boots from the SmartStart program, it automatically starts the System Configuration Utility. ■ Register your server. For complete details on the SmartStart program, read the SmartStart installation card included in your SmartStart package.
2-5 Power Requirements ! WARNING: To reduce the risk of personal injury, fire or damage to the equipment, do not overload the AC supply branch circuit that provides power to the rack.Consult the electrical authority having jurisdiction over your facility wiring and installation requirements.
2-6 Rack-Mountable Server Installation IMPORTANT: The use of common power outlet strips for this equipment is not recommended. For proper operation and safety, this equipment is required to be properly grounded. In the United States, install the equipment in accordance with NFPA 70-1993 (National Electric Code) Article 250, as well as any local and regional building codes. In Canada, the equipment should be installed in accordance with Canadian Standards Association, CSA C22.1, Canadian Electrical Code.
2-7 Equipment Included Maximum Internal Rack Temperature Rack-Mountable ProLiant Servers 50°C/122°F Compaq Rack-Mountable options 40°C/104°F Other manufacturers' options See other manufacturers' specifications CAUTION: To reduce the risk of damage to the equipment when installing third-party options: ■ Make sure that the option equipment does not impede airflow to the rack-mountable ProLiant server or increase the internal rack temperature beyond the Compaq specified maximum rating.
2-8 Rack-Mountable Server Installation CAUTION: If a third-party rack is used, the following minimum requirements should be observed to ensure adequate airflow and to prevent damage to the equipment: ■ Front: The rack door should have 120 square inches of holes evenly distributed from top to bottom to permit adequate air flow. ■ Side: The clearance between the installed module and the side panels of the rack should be a minimum of 2.75 inches.
2-9 ! WARNING: Before beginning to work on the rack, be sure that the leveling jacks are extended to the floor, that the full weight of the rack rests on the level floor, and that stabilizers are installed or that multiple racks are coupled for stability. Server Warnings and Precautions ! 39 - 50 kg 87 - 110 lb WARNING: To reduce the risk of personal injury or damage to the equipment: ■ Observe local Occupational Safety requirements and guidelines for heavy equipment handling.
2-10 Rack-Mountable Server Installation CAUTION: The rack-mountable Compaq ProLiant server must always be operated with the system unit top access panel on. Proper cooling will not be achieved if the system unit cover is removed. IMPORTANT: Because of the 100 to 120 VAC electrical rating of each power supply, some local electrical authorities may require either one 15-Ampere circuit for each power supply or one 20-Ampere circuit for each pair of power supplies.
2-11 Contents of the rack model server box include: ■ Compaq ProLiant 6500 Server ■ Assorted cables ■ Rack template ■ Rack-mounting hardware kit (See Figure 2-2 and Table 2-2.) 1 3 2 4 6 7 5 8 Figure 2-2.
2-12 Rack-Mountable Server Installation Table 2-2 Rack-Mounting Hardware Identifier ■ Description 1 One pair 24-inch slide rail assemblies 2 Rack-mounting brackets 3 Cable management arm bracket 4 Cable management arm 5 Bag of screws 6 Left and right rail covers 7 Cable management arm screw-retaining plate 8 Padlock and key kit Documentation and software ❏ Compaq ProLiant Setup and Installation Guide ❏ Quick Hardware Installation Poster ❏ SmartStart and Support Software CD ❏ Inst
2-13 Preparing the Rack-Mounting Brackets and Slide Rail Assemblies Each pair of Rack-mounting brackets, with attached slide rail assemblies, supports one rack-mountable server. Figure 2-3.
2-14 Rack-Mountable Server Installation Each slide rail assembly consists of an outer bracket rail and an inner server rail (shown in Figure 2-4). These pieces can be separated; the bracket rails attach to the Rack-mounting brackets (shown in Figure 2-3) and the server rails attach to the sides of the server chassis. Figure 2-4.
2-15 Figure 2-5. Removing the server rail from the bracket rail 3. Put the server rails to one side. You will attach them to the rack server chassis later in the section, "Attaching Server Rails to the Server." Figure 2-6 shows the separated bracket rail with its inner sliding piece and the flat, one-piece server rail. Figure 2-6.
2-16 Rack-Mountable Server Installation The bracket rail consists of a fixed outer rail that screws to the Rack-mounting bracket and an inner slide on a steel ball bearing movement. This inner slide does not detach. See Figure 2-7. Figure 2-7. Bracket rail with inner slide; the front of the rail is highlighted. 4. Lay the bracket rail inside the Rack-mounting bracket with the front of both pieces oriented in the same direction. Align the front screw hole in the Rack-mounting bracket and the bracket rail.
2-17 6. Fasten the bracket rail to the Rack-mounting bracket with three 8-32 x 1/4-inch slotted screws. (Do not use nuts or washers with the screws.) See step of Figure 2-8. 7. Adjust the inner slide to access the other two screw holes, one at a time, through the slotted opening in the inner slide. Use two more 8-32 x 1/4inch slotted screws to fasten the bracket rail to the Rack-mounting bracket. See steps and of Figure 2-8. Figure 2-8 shows insertion of the screws into the appropriate holes.
Rack-Mountable Server Installation 1 2 3 4 24 2 2-18 Figure 2-8. Attaching the bracket rail to the rack-mounting bracket You will use a total of five 8-32 x 1/4-inch slotted screws to fasten the bracket rail to the Rack-mounting bracket. When all five screws are fastened, the rackmounting bracket and bracket rail form a mounting bracket slide assembly that you will attach to the rack. 8. Repeat steps 4 through 7 with the other bracket rail and Rack-mounting bracket.
2-19 Attaching the Slide Rail Assembly to the Rack ! WARNING: To reduce the risk of personal injury or damage to the equipment, be sure that the rack leveling feet are extended to the floor and support the full weight of the rack. Each rack must be level and stable. Racks that are not coupled together require the installation of stabilizers. This must be done before you perform any work on the rack. See the Installing Rack Products CD for more information on leveling feet and stabilizers.
2-20 Rack-Mountable Server Installation IMPORTANT: The template is two-sided (front and back) and printed with arrows that show you where the screws are inserted, both for the mounting bracket assemblies and for the thumb screws that secure the server's face plate to the front of the rack. Align the template carefully with the holes on the rack to determine the exact placement of the screws. 2.
2-21 Inserting Cage Nuts into the Rack Frame After marking the positions for the fasteners in both the front and back of the rack, use the fitting tool to insert cage nuts on the inside of the rails at the marked locations. The cage nuts and fitting tool are included in the hardware kit supplied with the rack. 1. Position the cage nut on the inside of the rail as shown in Figure 2-10. 2. Hook one of the lips of the cage nut through the square rail perforation. 3.
2-22 Rack-Mountable Server Installation Attaching the Rack-mounting Bracket Assembly to the Rack 1. Using the pencil marks from the template, carefully align the rackmounting bracket assembly with the rear rack frame rail. 2. Using the tabs, insert the rear end of the rack-mounting bracket into the rear rack frame rail, as shown in Figure 2-11. CZR4-012.eps Figure 2-11. Back of mounting bracket assembly installed 3.
2-23 Figure 2-12. Attaching Rack-mounting bracket assembly to the front of the rack 4. After attaching both of the mounting bracket assemblies to the rack, prepare the server for mounting in the rack. Compaq ProLiant 6500 Setup and Installation Guide For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: C-CH02.
2-24 Rack-Mountable Server Installation Attaching Server Rails to the Server 1. Line up the tab on a server rail with the front of the server chassis. The holes in the server rail will line up only one way with the chassis. 2. Attach the flat side of a server rail to each side of the server chassis with four 8-32 x 1/4-inch Phillips-head screws. Do not use washers with the screws. See Figure 2-13. Figure 2-13.
2-25 IMPORTANT: To reduce the weight of the server and make it more manageable, do not install drives in the server until after you load the server into the rack. 1. Pull the slide rails forward from the mounting brackets. 2. Carefully align the server's rails with the rack's slide rails and begin to slide the server into the rack. CAUTION: Be sure to keep the server parallel to the floor when sliding the server rails into the slide rails. Tilting the server up or down could result in damage to the rails.
2-26 Rack-Mountable Server Installation 3. Press the server rail release latch on either side of the server and continue to slide the server into the rack. IMPORTANT: The first time you slide the server into the rack, you may have to apply some pressure. After the first time, the ball bearings in the slide will move easily. IMPORTANT: When servicing the server, fully extend the server rail until the latches lock. To return the server to the rack, press the latches and slide the server into the rack. 4.
2-27 Attach the cable management arm bracket to the back of the server with two 6-32 x .312 Torx screws. Figure 2-15. Attaching a cable management arm bracket to the server Attaching the Cable Management Arm A double-hinged cable management arm and fasteners ship with each server. The cable management arm attaches to the server's cable management arm bracket and to the rear frame of the rack. All cables to and from the server are tied to this arm.
2-28 Rack-Mountable Server Installation Figure 2-16. Attaching the cable management arm to the cable management arm bracket For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: C-CH02.
2-29 3. Align the other end of the cable management arm on the outside of the rear frame rail of the rack. Align the cable management arm screwretaining plate on the inside of the rack frame rail. Attach the arm to the rear frame rail of the rack with two 10-32 x 5/8-inch Phillips hex-washer screws, as shown in Figure 2-17. Figure 2-17.
2-30 Rack-Mountable Server Installation Cabling the Server 1. Connect the power cord(s) and peripheral devices such as the keyboard, mouse, and monitor. Tie-wrap the AC cord to the loop provided on the power supply to prevent the cord from being accidentally disengaged. Figure 2-18. Tie-wrapping the power cord to the loop provided ! WARNING: To reduce the risk of electric shock or damage to the equipment: ■ Install the power supply before connecting the power cord to the power supply.
2-31 ! WARNING: Do not place anything on power cord(s) or cables. Arrange them so that no one may accidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electrical outlet, grasp the cord by the plug. ! WARNING: To reduce the risk of electrical shock or fire, do not plug telecommunications/telephone connectors into the Network Interface Card (NIC) receptacles. 2. If you install a switch box in the rack, route the CPU-to-switch-box cables to the switch box. 3.
2-32 Rack-Mountable Server Installation Powering Up the Server You can now bring your ProLiant 6500 Server online in accordance with your network and operating system procedures. Press the Power On/Standby switch to ON. When the system is first powered ON, the system ROM detects the unconfigured state of the hardware and provides default configuration settings for most devices.
2-33 NOTE: Windows NT users may use the Compaq Power Down Manager to power down your server. For information, refer to the NTREADME.HLP file on diskette 1 of the NTSSD. 1. Press the Power ON/STANDBY switch to STANDBY. 2. Verify that the system LED on the front panel, located near the Power ON/STANDBY switch, turns OFF and that all fans stop spinning. 3. Disconnect all power cords from the server to disable all power to the server.
3-1 Chapter 3 Installing Hardware Options Compaq recommends that you use the documentation provided with the hardware options for complete installation instructions in addition to the instructions in this chapter. See also the Compaq ProLiant 6500 Hardware Installation and Configuration poster included in the shipping box or the labels attached under the top access panel.
3-2 Installing Hardware Options ■ Hot-Plug Area Access - This part covers the procedures for accessing areas in which to install hot-plug options, upgrades or replacements. These areas include: ❏ Five PCI Hot Plug expansion slots ❏ Hot-plug SCSI drive bays ❏ Hot-plug fans ❏ Hot-plug power supplies Non Hot-Plug Area Access The following section provides instructions on accessing non hot-plug areas of the server.
3-3 ! WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching. CAUTION: Electrostatic discharge can damage electronic components. Make sure you are properly grounded before beginning any installation procedure. Installing a Processor and Redundant Processor Power Module The ProLiant 6500 Server ships with at least one processor, one redundant processor power module installed, and up to three processor terminator modules.
3-4 Installing Hardware Options 1 2 Figure 3-1. Processor and redundant processor power module To install a processor 1 and a redundant processor power module 2, use the following installation procedure: 1. Back up the server data. 2. Shut down the operating system in an orderly manner as directed in the operating system instructions. 3. If the server is ON, set the power switch to STANDBY. 4.
3-5 IMPORTANT: The system power in the ProLiant 6500 Server does not completely shut off with the front panel Power ON/STANDBY switch. The two positions of the switch function as ON and STANDBY, rather than ON and OFF. The STANDBY position removes power from most of the electronics and the drives; however, portions of the power supply and some internal circuitry remain active. Consequently, to remove all power from the system, it is necessary to disconnect the power cord from the server.
3-6 Installing Hardware Options 7. Loosen the two tooled-access screws on the server cover with a Torx T15 screwdriver. 8. Slide the top access panel toward the rear of the unit about 1-inch (2.5 cm) and then lift the top access panel off the unit, as shown in Figure 3-2. Figure 3-2. Removing the top access panel 9. Locate an available processor socket and corresponding processor power module socket on the system board. Available sockets have a processor terminator module installed.
3-7 2 2 1 3 Figure 3-3. Removing the processor terminator module from the processor socket IMPORTANT: If you remove a processor, the processor terminator module must be reinstalled before powering up the server. Failure to have either a processor or processor terminator module installed results in an interlock fault condition which prevents the server from powering up. 11. Locate the core frequency switch for the processor socket. Set the processor core frequency switch to the appropriate setting.
3-8 Installing Hardware Options 2 2 1 Figure 3-4. Installing the redundant processor power module For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: D-CH03.
3-9 13. Align the new processor with the heatsink facing the side access panel of the server. See Figure 3-5 for proper orientation. 1 2 Figure 3-5.
3-10 Installing Hardware Options See Figure 3-6 for a detailed view of the server with four processors and redundant processor power modules installed. 4a 4 3 3a 2a 2 1 1a Figure 3-6.
3-11 14. Install the processor, pushing firmly until seated 1, and secure by rotating the ejector levers inward 2. When ejectors are seated, complete the installation by tightening the retention screw 3 finger-tight. See Figure 3-7. 3 2 2 1 Figure 3-7. Installing the processor 15. Reconnect the power cord(s) to the server. 16. Verify the interlock LEDs are normal. See Appendix D, “Interlock LEDs.” 17. Replace the top access panel. 18. Turn ON the server.
3-12 Installing Hardware Options Accessing the System Board Components The location of the system board components are shown in Figure 3-8. 1 2 3 4 5 6 7 12 8 9 13 16 25 17 18 24 19 20 21 22 23 15 11 10 14 Figure 3-8.
3-13 System Board Components Continued Identifier Component D Miscellaneous connector E IDE connector F Power sense connector G Memory board slot H Floppy power connector I Floppy signal connector NOTE: The ISA slot is for modem use only. The Remote Insight Board/PCI functions properly only when plugged into slots 5 and 6. NOTE: For location of the primary and secondary PCI Hot Plug slots, see the hood label under the top access panel of the server.
3-14 Installing Hardware Options Accessing the Memory Expansion Board Components The memory expansion board components are shown in Figure 3-9. DIMM 3 DIMM 4 DIMM 7 Bank 1 Bank 2 Bank 3 Bank 4 DIMM 8 DIMM 11 DIMM 12 DIMM 15 DIMM 1 DIMM 2 DIMM 5 DIMM 6 DIMM 9 DIMM 10 DIMM 13 DIMM 14 DIMM 16 Figure 3-9.
3-15 NOTE: After setting the Power ON/STANDBY switch to STANDBY, it may take the operating system up to 30 seconds before shutting down the power. IMPORTANT: The system power in the ProLiant 6500 Server does not completely shut off with the front panel Power ON/STANDBY switch. The two positions of the switch function as ON and STANDBY, rather than ON and OFF. The STANDBY position removes power from most of the electronics and the drives; however.
3-16 Installing Hardware Options 3. Loosen the two tooled-access screws on the top access panel with a Torx T-15 screwdriver. 4. Slide the top access panel toward the rear of the unit about 1-inch (2.5 cm) and then lift the top access panel off the unit as shown in Figure 3-10. Figure 3-10. Removing the top access panel ! WARNING: To reduce the risk of personal injury from hot surfaces, allow the internal system components to cool before touching them.
3-17 5. Remove the memory expansion board by rotating the latches outward 1 and pulling the board out 2, as shown in Figure 3-11. 1 2 1 Figure 3-11. Removing the memory expansion board Installing Additional DIMM Memory You can expand the existing memory in your server by installing industrystandard Dual Inline Memory Modules (DIMMs) into the memory expansion board. The following requirements must be met when installing additional memory. See also “Address Bit Permuting” later in this chapter.
3-18 Installing Hardware Options For an illustrated overview of the installation procedure, see the Hardware Installation and Configuration poster included in the shipping box and on the hood label under the top access panel. 1. Place the memory expansion board, components facing up, on a flat surface. CAUTION: The ejectors prevent the memory expansion board from laying completely flat.
3-19 2 1 2 Figure 3-13. Replacing the memory expansion board and securing the latches 7. Reconnect the power cord(s). 8. Verify the interlock LEDs are normal. See Appendix D, “Interlock LEDs.” 9. Replace the top access panel. 10. Turn on the server. See “Powering Up the Server” in Chapter 2. 11. Verify that the memory was installed correctly by reviewing the POST messages on the system console or memory information under the System Information Menu of the IMD.
3-20 Installing Hardware Options Memory Configuration Rules for Address Bit Permuting: ■ 2 or 4 banks on a memory expansion board must be populated. ■ All banks within an ABP group (2 banks for a 2-bank group and 4 banks for a 4-bank group) must be of the same memory capacity. ■ The memory in the expansion board must be populated starting with bank 1 and each populated bank must be adjacent.
3-21 Table 3-5 Peripheral Board Components Identifier Description 1 Internal battery 2 Configuration Maintenance Switch (SW1) 3 SCSI Connector Channel A 4 SCSI Connector Channel B 5 Serial B Connector 6a, 6b Stacked Parallel/External SCSI Connectors 7a, 7b Stacked Serial A/Video Connectors 8a, 8b Stacked Keyboard/Mouse Connectors NOTE: See Appendix C, “Switch Settings,” for Configuration Maintenance Switch Settings (SW1).
3-22 Installing Hardware Options 3. Remove the Integrated Management Display (IMD) cable and the power switch cable from the drive cage, as shown in Figure 3-15. The power switch cable is located next to the IMD cable. Figure 3-15. Removing the IMD cable For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: D-CH03.
3-23 4. Remove the SCSI, IDE, and Miscellaneous cables from the fan controller board. See Figure 3-16. 1 2 3 4 6 5 Figure 3-16.
3-24 Installing Hardware Options 5. Press the tabs at the front of the drive cage, as shown in Figure 3-17, and pull the drive cage out 2 to 3 inches. Figure 3-17. Removing the drive cage 6. Remove the SCSI backplane 2 x 6 pin power cable 1 from the back of the drive cage. See Figure 3-18. 1 Figure 3-18. Power cable connector on back of drive cage 7. Fully remove the drive cage.
3-25 Installing the Duplex Board Option NOTE: Be sure to follow all the steps under “Accessing the Drive Cage Backplane” before proceeding. 1. Remove the Pass-Thru Board as shown in Figure 3-19. 1 2 Figure 3-19. Removing the Pass-Thru board 2. Install the optional duplex enabler board, as shown in Figure 3-20. 2 1 Figure 3-20. Installing the optional duplex enabler board 3. Partially replace the drive cage, allowing access to the rear of the SCSI backplane.
3-26 Installing Hardware Options 4. Reconnect the SCSI backplane 2 x 6 pin power cable 1 to the back of the drive cage. See Figure 3-18. 5. Push the drive cage back fully until the front latches lock. 6. Replace the IDE and Miscellaneous cables on the fan controller board. 7. Replace the IMD cable, as shown in Figure 3-21, and the power switch cable that is located next to the IMD cable. Figure 3-21.
3-27 8. Connect the SCSI controller cables, as necessary. See Chapter 6, “Cabling Guidelines,” for more cabling information. Figure 3-22 shows an example controller connection to the Dual Channel Wide-Ultra SCSI-3 Controller. Figure 3-22. Example cable connection to SCSI controller 9. Reinstall the hot-plug fans. See Figure 3-34. 10. Reconnect the power cord(s) to the server. 11. Verify the System board interlock LEDs are normal. See Figure D-1 and Table D-1 in Appendix D, “System Board Interlock LEDs.
3-28 Installing Hardware Options Hot-Plug Areas This section describes access to the following areas: ■ PCI Hot Plug expansion boards (See Chapter 5 for operation information.) ■ Hot-plug SCSI drives ■ Hot-plug fans ■ Hot-plug power supplies Components in these areas have port-colored latches or levers to signify that they are hot-plug devices.
3-29 ! WARNING: Risk of injury or damage to the equipment from hazardous energy. The hot-plug access door provides access to hazardous energy circuits. The door should remain locked during normal operation-or-the server should be installed in a controlled access location where only qualified personnel have access to the server. 1. Unlock and open the PCI Hot Plug access door. See Figure 3-23.
3-30 Installing Hardware Options 2. Verify the status of the green LED 1 and amber LED 2, as shown in Figures 3-24 and 3-25 and Table 3-7. 3 2 1 Figure 3-24. PCI Hot Plug LED indicators 1, 2, and button 3 under the PCI Hot Plug access door Table 3-7 PCI Hot Plug Button and LEDs Identifier Description 1 Green LED 2 Amber LED 3 PCI Hot Plug Button 3. If the slot PCI Hot Plug slot green LED 1 is ON, power down the slot by using the slot PCI Hot Plug Button 3 or PCI Hot Plug utility application.
3-31 1 2 Figure 3-25. PCI Hot Plug LED indicators from rear of server CAUTION: DO NOT open the slot release lever unless the slot’s green PCI Hot Plug LED indicator is OFF. System power down and subsequent data loss could occur. Compaq ProLiant 6500 Setup and Installation Guide For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: D-CH03.
3-32 Installing Hardware Options 4. Press the top of the appropriate expansion slot release lever 1 and rotate the lever toward the rear of the expansion slot 2, as shown in Figure 3-26. 3 1 2 Figure 3-26. Opening slot release lever and removing the PCI expansion board 5. Remove the PCI expansion board 3, holding the board at each end, and carefully rocking it back and forth until the connectors pull free from the slot. Be careful not to scrape the board against another component.
3-33 6. Replace the same type of PCI expansion board into the same expansion slot, pushing firmly until securely seated 1, as shown in Figure 3-27. 1 2 Figure 3-27. Installing a PCI expansion board 7. 8. 9. Close the expansion slot release lever from the rear of the unit to secure the board. Make sure that the lever latches into the closed position 2. Connect the expansion board I/O cable as appropriate.
3-34 Installing Hardware Options Accessing Hot-Plug SCSI Hard Drives IMPORTANT: Before adding or removing any hot-plug SCSI drives, be sure to set the drive in the STANDBY mode, as directed by the operating system instructions. Important Guidelines About Replacing Hot-Plug SCSI Hard Drives When replacing hot-plug hard drives, these guidelines must be followed: ■ Never remove a hot-plug drive if the LED is green. Replace a hot-plug hard drive only when the drive’s LED is amber.
3-35 PRESS TO BOOT THE SYSTEM AND REBUILD THE REPLACED DRIVE , OR PRESS TO BOOT THE SYSTEM AND NOT REBUILD THE DRIVE(S). CAUTION: Pressing F2 will cause permanent data loss to the entire logical drive. F2 should be pressed only if all of the drives have been replaced or if complete data loss is desired. NOTE: When a drive configured for fault tolerance is replaced, the replacement drive automatically begins restoring when it is installed.
3-36 Installing Hardware Options 3. Insert the hot-plug SCSI hard drive into the empty drive bay, pushing until seated 1 as shown in Figure 3-28. Secure by swinging the ejector levers 2 inward. 2 1 Figure 3-28. Installing a hot-plug SCSI hard drive CAUTION: Make sure ejector levers are properly seated. 4. Place the hot-plug SCSI hard drive online as directed by your operating system instructions. If the drive was replaced, the array controller does an auto-spin up and starts rebuilding the drive.
3-37 Removing Hot-Plug Hard Drives 1. Locate the hot-plug hard drive to be removed from the drive bay. 2. Pinch both sides of drive levers to unlock 1, then swing the levers out 2 and remove the drive 3, as shown in Figure 3-29. 2 1 3 Figure 3-29. Removing a hot-plug drive 3. Insert a blanking panel into the empty drive bay, pushing until seated. CAUTION: Make sure unused drive bays contain a blanking panel to ensure proper airflow.
3-38 Installing Hardware Options Accessing and Installing Hot-Plug Fans CAUTION: Never remove both fans from either the processor or I/O section while the server is powered up. Removal could result in overheating and damage to hardware. Removing a Hot-Plug Fan 1. Unlock and open the hot-plug fan access door in the top access panel. Figure 3-30.
3-39 2. Locate the hot-plug fan to be removed. See Figure 3-31 for fan location and numbering. 2 1 4 3 Figure 3-31.
3-40 Installing Hardware Options 3. Verify the status of the fans by noting the LEDs on the housing of each fan, as shown in Figure 3-32. 2 1 Figure 3-32. Hot-plug fan LEDs Table 3-9 Hot-Plug Fan LEDs LED 1 and 2 Indication Status No light Power is not applied to the fan. 1 Green light Power is applied to the fan and fan is functional 2 Amber light Fan has failed.
3-41 4. After opening the hot-plug access door, pull the locking latch toward the center of the fan 1 and lift the hot-plug fan out of the fan cage 2, as shown in Figure 3-33. 2 1 Figure 3-33. Removing a hot-plug fan Installing a Hot-Plug Fan 1. Lower the new hot-plug fan into the fan cage until it clicks in place, as shown in Figure 3-34. Figure 3-34. Installing a new hot-plug fan 2. Close and lock the hot-plug fan access door.
3-42 Installing Hardware Options NOTE: Upon correct installation, fans activate and an event message displays on the Integrated Management Display (IMD). Pre-Failure Warranty The Compaq ProLiant 6500 Server includes Pre-Failure Warranty for Pentium II Xeon and Pentium III Xeon processors, hard drives, and DIMMs purchased from Compaq through a Compaq Authorized Reseller.
4-1 Chapter 4 Integrated Management Log The Compaq Integrated Management Log records system events and stores them in an easily viewable form. The Integrated Management Log provides greater serviceability to your Compaq server by recording hundreds of events. It also marks each event with a time-stamp with one-minute granularity. Events listed in the Integrated Management Log are categorized as one of four event severity levels: ■ Status/Informational--indicates that the message is informational only.
4-2 Integrated Management Log Integrated Management Display Distributed enterprise trends continue to affect the marketplace as companies expand globally and become more decentralized. As a result, server management tools and high-availability solutions are in high demand. Compaq has responded to customer needs for cost effective server management by providing the Compaq Integrated Management Display (IMD).
4-3 Configuring the Integrated Management Display The Compaq Integrated Management Display can be configured to display a variety of menus that you can customize to meet your specific needs. This section provides information on how to configure and customize the Integrated Management Display.
4-4 Integrated Management Log 10. Select Step 5: Save and Exit. 11. At the server prompt Save the Configuration and Restart the Computer, select OK=Enter. The changes you have entered will not be displayed on the Display Panel until you reboot the computer. Standard Integrated Management Display fields are defined in the section “Navigating the Menus,” later in this chapter. 12.
4-5 Idle Screen Text After the display has been idle for five minutes, the Integrated Management Display shows the following default screen text: COMPAQ PROLIANT 6500 ESC Figure 4-1. Idle screen text You can change this text by entering up to 3 lines, with no more than 16 characters on each line. One suggestion would be to enter the server name here. This would allow an administrator to walk into a room with several servers and immediately locate the desired server.
4-6 Integrated Management Log Server Information Server Name Enter up to 2 lines of no more than 14 characters each. An example might be to name the server by department, for example: CUST SERVICE WESTERN REGION Asset Tag Enter the server asset tag. Enter up to 2 lines of 16 characters each. Primary Operating System Enter the primary operating system of the server, for example, Windows NT 4.0. Enter up to 3 lines of 14 characters each.
4-7 Other This is a user-defined field. You can enter any additional administrator information. An example might be listing an additional administrator that serves as a backup to the primary administrator. Enter up to 2 lines of no more than 14 characters each. Service Information Name This field contains the name of the service provider. Enter up to 2 lines of no more than 14 characters each. Phone Number This field contains the phone number of the service provider.
4-8 Integrated Management Log Other This is a user-defined field. You can enter any additional service information. An example might be to enter service contract number. Enter up to 2 lines of no more than 14 characters each.
4-9 F1 Prompt Selecting this menu choice enables you to continue booting without a keyboard or monitor. This feature is useful for service and diagnostic purposes, allowing you to continue the boot up process without attaching a monitor and keyboard and their respective cables. Contrast You can adjust the level of contrast on the Integrated Display by using the up and down arrows. Press the Up arrow to increase the contrast, and press the Down arrow to decrease the contrast.
4-10 Integrated Management Log ESC 4 1 3 2 Figure 4-2. Integrated Management Display buttons Table 4-1 IMD Navigation Buttons Buttons Function 1 ESCAPE key which also allows travel back up the menu. 2, 3 DOWN and UP arrow keys allow the user to move through the menu screens and choose menu items. 4 ENTER key which also allows the server to travel down through the menus.
4-11 Display Symbols There are three different display symbols used to indicate your options as you scroll through the menus. These symbols are the Up, Down, and Selector arrows described in Table 4-2. Table 4-2 Integrated Management Display Symbols Functional Arrows Display Symbol Meaning Right Arrow Selector arrow shows current menu item. Press Enter on the IMD to select the menu item to the right of this arrow.
4-12 Integrated Management Log System Behavior with Error Events After system POST, if there is an F1 error condition, the IMD flashes the message: LCD-013.EPS !ALERT! Press Any Key to View New Events ESC Figure 4-3. New event message At this point, you must scroll through each screen of the event information menu before the IMD allows you to move on to other menu choices. The display will not allow you to escape the Unviewed Events section until you have examined all of the information stored there.
4-13 Administration Information ■ ■ ■ Server ❏ Server Name ❏ Asset Tag ❏ Operating System ❏ Other Administrator ❏ Name ❏ Phone ❏ Pager ❏ Other Service ❏ Name ❏ Phone ❏ Pager ❏ Other ■ Custom Menu Item (if entered) ■ Custom Menu Screen (if entered) System Information ■ ROM Date ■ Bootblock Date ■ Memory ■ Processors Contrast ■ Contrast Compaq ProLiant 6500 Setup and Installation Guide For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Wri
4-14 Integrated Management Log Compaq Insight Manager Compaq Insight Manager is a server management tool that provides in-depth fault, configuration, and performance monitoring of hundreds of Compaq servers from a single management console. System parameters that are monitored describe the status of all key server components. By being able to view the events that may occur to these components, you can take immediate action.
4-15 Compaq Survey Utility The Compaq Survey Utility is a serviceability tool available for Windows NT and Novell NetWare that delivers online configuration capture and comparison to maximize server availability. It is available on the Compaq Management CD in the SmartStart package or on the Compaq website at www.compaq.com. Refer to the Compaq Management CD for information on installing and running the Survey Utility.
5-1 Chapter 5 PCI Hot Plug Technology Introduction This chapter includes a brief discussion of PCI Hot Plug technology. For more information, see the online PCI Hot Plug Administration Guide on the Systems Reference Library CD. The ProLiant 6500 Server supports PCI Hot Plug.
5-2 PCI Hot Plug Technology IMPORTANT: If any of the three required components are not hot-plug aware, the system is fully functional, though not PCI Hot Plug capable. IMPORTANT: Before adding or removing any PCI Hot Plug devices, be sure to remove power to the slot using the PCI Hot Plug application. Failure to do so could result in critical errors. See “PCI Hot Plug Technology” and Table 5-1, “PCI Hot Plug LEDs,” in Chapter 5.
5-3 PCI Hot Plug System A PCI Hot Plug-capable system includes the system hardware, operating system, and device driver support required for PCI Hot Plug. An existing adapter board should be hot-plug capable as long as it is in compliance with the established PCI specification and has hot-plug device driver support. If any of the three required components are not hot-plug capable, the system is still fully functional, though not hot-plug capable.
5-4 PCI Hot Plug Technology PCI Hot Plug LEDs The PCI Hot Plug LEDs at each expansion slot provide a visual reference of the status of each board slot. The LEDs are viewed from the rear of the server or by opening the PCI Hot Plug access doors on the top panel. See Figure 5-1 and Table 5-1 for the appropriate slot condition and status for each state of the two LEDs. 3 2 1 Figure 5-1.
5-5 Table 5-1 PCI Hot Plug LEDs LED Power Status 1 Green ON 2 Amber OFF 1 Green ON 2 Amber ON OK to Open Slot Status No Power is currently applied to the slot. Do NOT open the slot release lever. The slot is functioning normally. No Power is currently applied to this slot but the slot needs ATTENTION for possible problem with the slot, board or driver. Do NOT open the slot release lever. Follow these steps: 1.
5-6 PCI Hot Plug Technology PCI Hot Plug LEDs Continued LED Power Status 1 Green Flashing 2 Amber ON 1 Green OFF 2 Amber ON OK to Open Slot Status No Power slot is being turned OFF or ON which may take several minutes. There may be a problem with the slot, the PCI board or the driver. DO NOT open the slot release lever until the green LED is completely OFF. No Power to this slot is turned OFF but this slot needs ATTENTION. There may be a problem with the slot, board or driver. 1.
5-7 PCI Hot Plug Application Support In partnership with Microsoft and Novell, Compaq has developed software support implementations for each company’s operating system. SCO support will be available soon; check the Compaq website for availability at www.compaq.com. Compaq is promoting standardization with these operating system software leaders to ensure the broad availability of PCI Hot Plug technology.
5-8 PCI Hot Plug Technology 3. At any point if you want to return to the Main menu, press the ESC button. 4. Press F1 for online help. Performing Hot-Plug Actions The Compaq PCI Hot Plug and the intraNetWare PCI Hot Plug application work together to allow the following hot-plug actions: ■ Hot removal of adapters - You can manually shut down and permanently remove an adapter, regardless of whether it is working or has failed.
5-9 Removing an Adapter 1. From the Main menu, highlight the slot and adapter to be removed. 2. Press Enter to go to the Slot +Options menu. 3. Use the arrow keys to select Remove Adapter and press Enter. NCMCON then processes the remove request. Once the slot has a status of POWERED OFF and green LED is no longer lit, you can physically remove the adapter by opening the slot release lever and taking the adapter out of the slot. NCMCON updates the status of the slot.
5-10 PCI Hot Plug Technology Novell intraNetWare Operating System Messages Adapter Not Same – Adapter is not the same as the adapter being replaced. Hotplug replacement cannot continue. Card Functioning – Adapter in slot is currently functioning. Add/Replace is ignored. Driver in Use – Adapter is currently in use. Do you wish to force removal? Driver Loaded – Driver for adapter is currently loaded. Unload driver and select again. General Failure – Could not perform action because of system failure.
5-11 PCI Hot Plug Utility for Windows NT The Compaq PCI Hot Plug Utility for Windows NT allows you to view the status of the PCI Hot Plug slots and to initiate actions such as replacing a failed card. The Windows NT PCI Hot Plug utility screen is divided into three sections: ■ Top - This area allows you to connect to a remote computer by either typing the machine name in the combo box, selecting a machine from the combo box or using the Browse button to bring up a selection dialog.
5-12 PCI Hot Plug Technology Connecting to a remote machine Select the remote machine to which you want to connect by any of the following methods: ■ Type the name of the machine in the combo box and press Enter. ■ Select one of the ten most recently connected machines from the dropdown list. ■ Click the Browse button to bring up a machine selection dialog box. Replacing an adapter 1. In the PCI Hot Plug Utility, turn the power OFF to the required slot by selecting it and clicking the Power button.
6-1 Chapter 6 Cabling Guidelines This chapter discusses connections and cabling considerations for the Compaq ProLiant 6500 Server. Connectors, guidelines, and cabling examples are presented. Network Interface Controller (NIC) Connecting the Network Cables Connect a single network cable to each port of the NIC: ■ For 100BASE-TX, your network cable must be Category 5, twisted-pair wiring. If you plan to run the NIC at 100 Mbps, it must be connected to a 100BASE-TX hub or switch (not a 100BASE-T4 hub).
6-2 Cabling Guidelines External Cabling 1 2 3 4 5 6 7 8 9 10 11 Figure 6-2.
6-3 SCSI Cabling The Compaq ProLiant 6500 Server provides one hardwired and three configurable SCSI buses for maximum configuration flexibility. This flexibility, combined with a maximum of five optional, integrated dual-channel Wide-Ultra SCSI-3 controllers (assuming one expansion slot is occupied by a NIC), results in a large number of possible SCSI configurations. For information on SCSI controllers and configurations supported on the Compaq ProLiant 6500 Server, see the following URL: www.compaq.com.
6-4 Cabling Guidelines 1 2 3 4 6 5 Figure 6-3. Connectors on fan controller board Table 6-2 Connectors on Fan Controller Board Identifiers Description 1 B-SCSI 2 C-SCSI 3 A-SCSI 4 C-SCSI 5 Miscellaneous 6 IDE A-SCSI Bus The A-SCSI bus connects to SCSI hard drive slots 0 through 6 when the PassThru Board is installed, as shown in Figure 6-4. In this configuration, the A-SCSI bus is also routed to the A/B-SCSI removable media connector on the back of the drive cage shown in Figure 6-6.
6-5 When the optional Duplex Enabler Board is installed, the A-SCSI bus is routed to SCSI hard drives 0 through 3 only, as shown in Figure 6-4. C-SCSI A-SCSI Fan Controller Board B-SCSI C-SCSI Pass-Thru Board 0 1 2 3 SCSI Hard Drives Hard Drive Backplane Board 4 5 6 C-SCSI A/B-SCSI May connect to internal devices Figure 6-4.
6-6 Cabling Guidelines B-SCSI Bus The B-SCSI bus connects to SCSI hard drive slots 4 through 6 when the optional Duplex Enabler Board is installed, as shown in Figure 6-5. In this case, slots 4 through 6 become SCSI IDs 0 through 2 respectively on the B-SCSI bus. When the Pass-Thru Board is installed, the B-SCSI bus is not used. In a duplex SCSI configuration, the B-SCSI bus is also routed to the A/B-SCSI connector on the back of the drive cage shown in Figure 6-5.
6-7 Removable Media Bay Connectors The A/B-SCSI Removable Media Bay connector, shown in Figure 6-6, is connected to the A-SCSI bus when the Pass-Thru Board is installed or the BSCSI bus when the optional Duplex Enabler Board is installed. The C-SCSI Removable Media Bay connectors are connected to the controller that you connected to the C-SCSI connector on the fan controller board.
6-8 Cabling Guidelines 1 2 4 3 Figure 6-6. Removable Media Bay connectors Table 6-3 Removable Media Bay Connectors Identifier Description 1 A/B SCSI 2 IDE 3 C-SCSI wide 4 C-SCSI narrow For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: G-CH06.
6-9 Determining Cabling Needs To determine the SCSI cables needed for your application: 1. Determine whether the cabling needs are internal or external. 2. Determine whether external cabling needs are for primary storage (hard drive) or for secondary storage (tape drive or CD-ROM in the removable media bay). 3. Identify the controller type. 4. Identify the drive type, drive cage, and expansion slot to be used.
6-10 Cabling Guidelines Table 6-4 Internal SCSI Cabling (Simplex Backplane Configuration) Controller Wide-Ultra, Fast-Wide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays All cables for this 35/70 DLT in Removable Media Bays All cables for this Integrated Dual All cables for this Channel Wide- configuration are supplied configuration are supplied Ultra SCSI-3 with the system. with the system.
6-11 Internal SCSI Cabling (Simplex Backplane Configuration)Continued Controller Wide-Ultra, Fast-Wide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays 35/70 DLT in Removable Media Bays All cables for this All cables for this Wide-Ultra All cables for this SCSI-3 configuration are supplied configuration are supplied Controller, Dual with the system. with the system. with the system.
6-12 Cabling Guidelines Internal SCSI Cabling (Simplex Backplane Configuration)Continued Controller Wide-Ultra, Fast-Wide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays This configuration is not SMART-2SL, All cables for this SMART-2DH configuration are supplied supported. Array with the system. Controller, Smart Array 3200 Controller 35/70 DLT in Removable Media Bays This configuration is not supported.
6-13 Table 6-5 Internal SCSI Cabling (Duplex Backplane Configuration) Controller Wide-Ultra, Fast-Wide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays Integrated Dual All cables for this Channel Wide- configuration are supplied configuration are supplied Ultra SCSI-3 with the system.
6-14 Cabling Guidelines Internal SCSI Cabling (Duplex Backplane Configuration)Continued Controller Wide-Ultra, FastWide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays 35/70 DLT in Removable Media Bays Wide-Ultra SCSI- All cables for this All cables for this All cables for this 3 Controller Dual configuration are configuration are supplied configuration are supplied Channel Wide- supplied with the system.
6-15 Internal SCSI Cabling (Duplex Backplane Configuration)Continued Controller Wide-Ultra, FastWide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays 35/70 DLT in Removable Media Bays SMART-2SL, All cables for this This configuration is not This configuration is not Smart Array configuration are supported. supported. 3200 Controller supplied with system.
6-16 Cabling Guidelines Internal SCSI Cabling (Duplex Backplane Configuration)Continued Controller Wide-Ultra, FastWide, and Fast SCSI-2 Hard Drives in Hot-plug Drive Cage Only 4/8 DAT Drive, 12/24 DAT Drive, 20/40 DLT or SCSI CD-ROM in Removable Media Bays 35/70 DLT in Removable Media Bays SMART-2DH Additional cables are This configuration is not This configuration is not Array Controller required. supported. supported.
6-17 SCSI Cabling Examples Example 1: Standard Configuration The Compaq ProLiant 6500 Server is configured at the factory for a standard SCSI Configuration, as shown in Figures 6-7 and 6-8. This configuration uses the Dual Channel Wide-Ultra SCSI-3 Controller to handle all seven SCSI drive bays. The Pass-Thru Board is installed on the back of the SCSI backplane board. 2 3 1 4 8 7 6 5 9 0 1 2 3 11 4 5 6 10 13 12 Figure 6-7.
6-18 Cabling Guidelines Identifier Description 1 System board 2 Peripheral board 3 Peripheral board B-SCSI port 4 Peripheral board A-SCSI port 5 Fan controller board 6 Fan controller board B-SCSI connector 7 Fan controller board A-SCSI connector 8 Fan controller board C-SCSI connector 9 Fan controller board C-SCSI connector : SCSI backplane board ; Pass-Thru board < C-SCSI connectors = A/B-SCSI connector For use with Pentium II Xeon and Pentium III Xeon processor-based servers o
6-19 Connect cable number 199606-015 (ships with server) from the integrated controller connector A-SCSI to the A-SCSI connector on the fan controller board, as shown in Figures 6-7 and 6-8. Figure 6-8. Example 1: Cable routing Example 2: Integrated Duplex Configuration 1. To enable duplex mode, install the optional Duplex Enabler Board on the back of the Drive Cage. See “Accessing the Drive Cage Back Plane” through “Installing the Optional Duplex Enabler Board Option” in Chapter 3. 2.
6-20 Cabling Guidelines 2 3 1 4 7 8 6 5 9 0 1 2 3 11 4 5 6 10 13 12 Figure 6-9.
6-21 Integrated Duplex Configuration Example Continued Identifier Description 7 Fan controller board A-SCSI connector 8 Fan controller board C-SCSI connector 9 Fan controller board C-SCSI connector : SCSI backplane board ; Duplex Enabler board < C-SCSI connectors = A/B-SCSI connector Figure 6-10. Example 2: Cable routing Example 3: Smart Array 3200 Duplex Configuration 1. To enable duplex mode, install the optional Duplex Enabler Board on the back of the drive cage.
6-22 Cabling Guidelines 3. Install cable part number 199606-002 (ships with server) from the Smart Array 3200 controller Port 2 connector to the B-SCSI connector on the fan controller board, as shown in Figure 6-11 and 6-12. 14 2 15 3 16 1 4 7 8 6 5 9 0 1 2 3 11 10 4 5 6 13 12 Figure 6-11.
6-23 Smart Array 3200 Controller Duplex Configuration Example Continued Identifier Description 6 Fan controller board B-SCSI connector 7 Fan controller board A-SCSI connector 8 Fan controller board C-SCSI connector 9 Fan controller board C-SCSI connector : SCSI backplane board ; Duplex Enabler board < C-SCSI connectors = A/B-SCSI connector > Smart Array 3200 Controller ? Smart Array 3200 Controller Port 1 connector @ Smart Array 3200 Controller Port 2 connector Figure 6-12.
6-24 Cabling Guidelines Example 4: SMART-2DH External Configuration 1. Configure the Dual-Channel Wide-Ultra SCSI-3 controller and internal drive cage as needed. 2. Using the internal to external VHDCI cable (340589-003) provided with the server, connect the internal connector on the SMART-2DH Array Controller board to either VHDCI knockout on the rear wall of the server. See Figure 6-13. 3.
6-25 Figure 6-14. Example 4: External cabling for SMART-2DH external configuration PCI Hot Plug Cabling When connecting cables to boards installed in the PCI Hot Plug expansion slots, be sure to allow some slack in any cables running across the top of expansion boards so that they can be pushed aside if needed to remove any of the boards under hot plug conditions.
6-26 Cabling Guidelines IDE Removable Media Cabling The Compaq ProLiant 6500 is configured at the factory to use the integrated IDE controller to control a CD-ROM drive in the Removable Media Bay. The integrated IDE controller is connected to the IDE connector on the fan controller board, as shown in Figure 6-15. The IDE connector on the fan controller board is hardwired to the IDE connector on the back of the drive cage. 1 2 3 4 6 5 Figure 6-15.
6-27 Figure 6-16. IDE Cabling Power Cabling ! WARNING: Before removing the top access panel, make sure that the server is set in the STANDBY position and that the power cord(s) is disconnected from the electrical outlet. IMPORTANT: The system power in the ProLiant 6500 does not completely shut off with the front panel Power ON/STANDBY switch. The two positions of the switch function as ON and STANDBY, rather than ON and OFF.
6-28 Cabling Guidelines ! WARNING: To reduce the risk of electric shock or damage to the equipment: ■ If the system has multiple power supplies, disconnect power from the system by unplugging all power cords from the power supplies ■ Do not disable the power cord grounding plug. The grounding plug is an important safety feature. ■ Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all times. Securing the Power Cords Plug in the power cord.
7-1 Chapter 7 Server Configuration and Utilities Compaq provides many tools to assist you in the configuration and management of your Compaq ProLiant 6500 server. This chapter focuses on Compaq SmartStart and the Compaq System Configuration Utility, which includes Diagnostics and Utilities. For more information, refer to the Compaq Systems Reference Library CD.
7-2 Server Configuration and Utilities 4. Close the tray by again pressing the LOAD/UNLOAD button ✟. 1 2 Figure 7-1. Opening the internal CD-ROM tray 5. When the BUSY LED indicator turns GREEN, the drive is ready to receive commands and the SmartStart installation sequence begins. Opening the Internal CD-ROM Tray Manually If the CD-ROM tray does not open automatically, you can open it manually by using the emergency load/unload button.
7-3 1. Insert a metal rod, such as a straightened paper clip, into the manual effect hole and push firmly. The tray releases. Figure 7-2. Opening the internal CD-ROM tray manually 2. Slowly pull the tray out from the drive until the tray is fully extended, then remove the disc. To configure the server and load the operating system, refer to the SmartStart documentation provided in the Server Setup and Management pack that shipped with your server.
7-4 Server Configuration and Utilities ■ Stores configuration information in non-volatile memory ■ Assists in the installation of the operating system ■ Assists in running diagnostic tools such as TEST and INSPECT Utilities Installing an Operating System Compaq ProLiant 6500 servers support the following operating systems: ■ Novell intraNetWare and Novell NetWare 5 ■ Windows NT 3.51 and 4.0 ■ SCO OpenServer Release 5 ■ SCO UnixWare 2.12 and 2.
7-5 ■ SCO UnixWare 2.12 and 2.13 ■ IBM OS/2 Warp Server 4.0 SMP Diagnostics and Other Utilities ■ When you select the Diagnostics and Utilities feature from the System Configuration Utility main menu, the utility provides prompts to test, inspect, upgrade, and diagnose the server. ■ Diagnostics and Utilities are located on the system partition on the hard drive and must be accessed when a system configuration error is detected during the Power-ON Self-Test (POST).
A-1 Appendix A Regulatory Compliance Notices Federal Communications Commission Notice Class A Equipment This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
A-2 Regulatory Compliance Notices Declaration of Conformity for products marked with the FCC logo United States only This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For questions regarding your product, contact: Compaq Computer Corporation P. O.
A-3 Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union Notice Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
B-1 Appendix B Electrostatic Discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device. To prevent electrostatic damage, observe the following precautions: ■ Avoid hand contact by transporting and storing products in static-safe containers.
B-2 Electrostatic Discharge If you do not have any of the suggested equipment for proper grounding, have a Compaq Authorized Reseller install the part. NOTE: For more information on static electricity or assistance with product installation, contact your Compaq Authorized Reseller. For use with Pentium II Xeon and Pentium III Xeon processor-based servers only Writer: Sam Ogden Project: Compaq ProLiant 6500 Setup and Installation Guide Comments: 328196-002 (February 1999) File Name: J-APPB.
C-1 Appendix C Switch Settings Maintenance Configuration Switch Functions (SW1) For location of the Maintenance Configuration Switch (SW1) switch, see the hood label under the top access panel of the server.
C-2 Switch Settings Core Frequency Switch (SW2 and SW3) For location of the Core Frequency Switch (SW2 and SW3), see the hood label under the top access panel of the server.
D-1 Appendix D LEDs Interlock LEDs IMPORTANT: This server is not equipped with chassis interlocks; however, board interlocks are provided that connect the memory board, all processors, the peripheral board, the miscellaneous cable and the power switch cable in one interlock chain. When one of the connected components in the interlock chain is improperly seated in its connector, the LED associated with the fault origination point will illuminate on the system board.
D-2 LEDs Table D-1 System Board Interlock LEDs Memory CPU4 CPU3 CPU2 CPU1 I/O Misc.
D-3 Network Interface Controller (NIC) LEDs The NIC has three diagnostic LEDs above each cable connector port as shown in Figure D-2. These lights indicate the connector, cable or switch/hub status. Table D-2 indicates the status of the cable connector ports for each state of the three NIC LEDs: 1 2 3 1 2 3 Figure D-2.
D-4 LEDs NIC LEDs Continued LED 2 Activity (ACT) 3 100 Mbps Indication Cable Connector Port Status ON or flashing (Green) The NIC is sending or receiving network data. The frequency of the flashes varies with the amount of network traffic. OFF The NIC is not sending or receiving network data. ON (Green) Operating at 100 Mbps. OFF Operating at 10 Mbps. PCI Hot Plug LEDs The PCI Hot Plug LEDs at each expansion slot provide a visual reference of the status of each board slot.
D-5 Table D-3 PCI Hot Plug LEDs LED Power Status 1 Green ON 2 Amber OFF 1 Green ON 2 Amber ON OK to Open Slot Status No Power is currently applied to the slot. Do NOT open the slot release lever. The slot is functioning normally. No Power is currently applied to this slot but the slot needs ATTENTION for possible problem with the slot, board or driver. Do NOT open the slot release lever. Follow these steps: 1.
D-6 LEDs PCI Hot Plug LEDs Continued LED Power Status 1 Green OFF 2 Amber ON OK to Open No Slot Status Power to this slot is turned OFF but this slot needs ATTENTION. There may be a problem with the slot, board or driver. 1. Open the slot release lever (the amber LED turns OFF). 2. Remove or replace the board. 3. Connect the cables to the PCI board. 4. Close the slot release lever. 5. Return power to the slot through the PCI Hot Plug application (the green LED turns ON).
D-7 Hot-Plug Fan LEDs See Figure D-4 and Table D-4 for hot-plug fan LEDs and status indicators. 2 1 Figure D-4. Hot-plug fans Table D-4 Hot-Plug Fan LEDs LED 1 and 2 Indication Status No light Power is not applied to the fan. 1 Green light Power is applied to the fan and fan is functional. 2 Amber light Fan has failed.
D-8 LEDs Power Supply LEDs See Figure D-5 and Table D-5 for power supply LEDs and status indicators. 1 2 Bay 2 Bay 1 Figure D-5.
D-9 SCSI Hard Drive LEDs See Figure D-6 and Table D-6 for SCSI hard drive LEDs and status indicators. 1 2 3 Figure D-6.
Index-1 C Index A A/B-SCSI connector 6-6, 6-7 About This Guide ix administrator password 1-16 agents Insight Manager 1-12 alert fault conditions 1-12 A-SCSI bus 6-3, 6-4 ASR-2 1-10, 1-14 Assembly 3-1 Auto Line Sensing 1-4 Automatic Server Recovery See ASR-2 Automatic Server Recovery-2 See ASR-2 B Banks, memory 1-6 bracket, cable management arm 2-26 B-SCSI bus 6-3, 6-6 buses A-SCSI 6-4 B-SCSI 6-6 C-SCSI 6-6 PCI local bus 1-8 SCSI 6-3 SCSI with duplex board 6-5 buttons browse, Windows NT 5-11 Compaq Insigh
Index-2 Compaq Continued authorized service provider 1-17 Hardware installation and Configuration poster See Hardware and Configuration poster Integrated Management Log 1-11.
Index-3 diskette Continued power-ON password 1-16 write control 1-16 Drive Array Advanced Diagnostics See DAAD drive cage power cable connector 3-24 removal 3-21, 3-24 drivers See device drivers drives, loading in rack server 2-3 Dual Inline Memory Modules See DIMMs duplex board effect on SCSI buses 6-5 installation 3-21 installing 3-25 E EDO memory 3-17 electrostatic discharge B-1 error events, IMD 4-12 Ethernet 1-7 100TX Ethernet 1-8 10BaseT Ethernet 1-8 examples, SCSI cabling 6-17 expansion slots gener
Index-4 high-availability features Continued hot-plug redundant power supplies 1-1 Integrated Remote Console (IRC) 1-1 PCI Hot Plug slots 1-1 redundant hot-plug fans 1-1 redundant network interface controllers (NIC) 1-1 redundant processor power modules 1-1 server management and configuration tools 1-1 Smart Array 3200 Controllers 1-1 SMART-2DH Array Controllers 1-1 hot plug internal bays 1-4 messages, IMD 5-9 messages, intraNetWare 5-9 overview 5-1 redundant power supplies 1-4 removing an adapter, intraNe
Index-5 IMD Continued configuring 4-3 contrast 4-13 custom menu item 4-5 customizing fields 4-4 customizing idle screen text 4-5 customizing server 4-6 features 4-2 menu structure 4-12 menus 4-2 navigating the menus 4-9 new event message, illustrated 4-12 overview 4-2 server information 4-6 service provider 4-7 standard fields 4-8 system information 4-13 unviewed events 4-12 verifying memory 3-20 IMD, features ease of use 4-2 flexibility 4-2 manageability 4-2 IMD, navigating the menus display sysmbols 4-11
Index-6 interface Continued serial control 1-16 Internet xiv interrupts 1-10 intraNetWare, PCI hot plug actions 5-8 IRC overview 1-13 server management 1-13 IRQs 1-10, 7-3 ISA modem slots 1-3 K keyboard interface 1-7 password 1-16 L L2 cache memory 1-2 label installing DIMMs 3-18 labels installing options 3-1 LEDs hot plug 3-30 hot plug, PCI 5-4 online 3-34 powering down 2-33 LEDs, PCI Hot Plug D-4 list of events Compaq Servers Troubleshooting Guide 1-13, 4-15 load balancing 1-4 Logs, Server Health 1-9
Index-7 microcontroller monitoring 1-4 mounting bracket for rack server 2-14 mounting bracket for rack server 2-13 mouse 1-7 N navigation buttons IMD 4-9 NCMCON See Configuration Manager Console network controller redundant network controller 1-8 network controllers 10/100 TX UTP controller 1-8 dual port 1-8 overview 1-8 network interface controller (NIC) 1-3 network server mode 1-16 NICs overview 1-8 nonvolatile memory 1-10 O OFF 2-32 ON 2-32 operating system 7-3 installing 7-4 loading 7-3 SMP 7-4 suppo
Index-8 power cable connector drive cage 3-24 power cords securing 6-28 Power Down Manager 2-33 power margin 1-5 power supplies 1-9 supported 1-4 power supply advanced features 1-4 power supply utility 1-4 powering down 2-32 LEDs 2-33 powering up 2-32 Power-On Self-Test See POST precautions rack xiv Pre-Failure Insight Manager alert 3-42 Warranty 3-42 processor boards 1-2 failed 3-3 Pentium II Xeon 1-1 Pre-Failure Warranty 3-42 sockets 3-3 Q QuickLock 1-16 R rack attaching component rail to server 2-24 c
Index-9 SCSI buses 6-3 cabling 6-3 cabling examples 6-17 connectors 6-4 controllers 6-3 drive cage removal 3-21 drive configurations 1-14 drive, factory configuration 6-17 duplex board installation 3-21 ID numbers with duplex board 6-6 pass-thru board removal 3-21 storage capacity 1-14 support 1-7 security 1-12 serial interface control 1-16 server customizing 4-6 Health Logs 1-9 integrated 512-KB secondary cache 1-2 management and configuration 1-9 rack slide rail assembly 2-14 Rack-mounting bracket 2-13,
Index-10 System Configuration Utility Continued overview 1-10 server management 1-10 starting SmartStart from 2-4 to run 4-3 upgrading 4-4 system partition creation of 1-10 SystemConfigurationUtility SmartStart 1-10 T tables hot-plug fan LEDs D-7 IMD navigation buttons 4-10 IMD symbols 4-11 interlock LEDs D-2 NIC LEDs D-3 power supply LEDs D-8 rack internal temperature maximums 2-7 SCSI hard drive LEDS D-9 tables, PCI Hot Plug LEDs 5-4, D-5 technical support xv telephone numbers xiv temperature operating
Index-11 warnings Continued power supplies 2-30 rack stability 2-19 Warranty Pre-Failure 3-42 website xiv website, Compaq 6-9 Windows NT PCI Hot Plug actions 5-11 replacing a PCI Hot Plug adapter 5-12 Windows NT Utilities power down 2-33 www.compaq.
