HP ProLiant SL160z G6 Server Maintenance and Service Guide Part number 571293-005 Fifth edition March 2011
Legal notices © Copyright 2010, 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Contents Customer self repair ............................................................................................................................. 5 Parts only warranty service .......................................................................................................................... 5 Illustrated parts catalog ....................................................................................................................... 16 Mechanical components ..............................
Power-on Self-Test (POST) ........................................................................................................................... 72 POST Error Indicators ........................................................................................................................... 72 POST Errors Message Definition ............................................................................................................ 73 POST Related Troubleshooting ......................................
Customer self repair HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and allow for greater flexibility in performing defective parts replacement. If during the diagnosis period HP (or HP service providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory.
Réparation par le client (CSR) Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le client) afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses. Si pendant la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la réparation peut être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement.
Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo spedirà direttamente al cliente per la sostituzione.
Customer Self Repair HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu.
Reparaciones del propio cliente Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar (Customer Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad a la hora de realizar sustituciones de componentes defectuosos.
Customer Self Repair Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is. Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd.
Reparo feito pelo cliente Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se, durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente ao cliente.
Customer self repair 12
Customer self repair 13
Customer self repair 14
Customer self repair 15
Illustrated parts catalog Mechanical components Item Description Spare part number Customer self repair 1 Top cover Mandatory1 2 X16 riser card bracket Mandatory1 3 1U tray for 160 system Mandatory1 4 X4 riser card cage Mandatory1 5 Fan blank kit Mandatory 6 Power supply blank kit Mandatory1 Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service.
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous seront facturés. 1 Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont également conçues pour permettre au client d'effectuer lui-même la réparation.
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la palabra “No” en el catálogo ilustrado de componentes. Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening. 1 Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen zijn ontworpen voor reparatie door de klant.
Illustrated parts catalog 19
System components Item Description Spare Part Number Customer Self Repair 1 System Fan 576898-001 Mandatory1 2a SATA cable 1 576895-001 Mandatory1 2b SATA cable 2 576895-001 Mandatory1 3 PCIe X16 riser card 536654-001 Optional2 4 Memory Module 5 Mandatory1 DIMM 1GB PC3-10600E 501539-001 Mandatory1 DIMM 2GB PC3-10600E 501540-001 Mandatory1 DIMM 2GB PC3-10600R 501533-001 Mandatory1 DIMM 4GB PC3-10600R 501534-001 Mandatory1 DIMM 4GB PC3-8500R 501535-001 Mandatory1 DIMM 8G
Item Description Spare Part Number Customer Self Repair Intel Xeon 4c, 2.4 GHz, 12M, 80W 594887-001 Optional2 Intel Xeon 6c, 2.4 GHz, 12M, 60W 594890-001 Optional2 Intel Xeon 4c, 2.13 GHz, 12M, 40W 594891-001 Optional2 Intel Xeon 2.13GHz/800/4M/4c/4.8 QPI/80W 506013-001 Optional2 Intel Xeon 2.00GHz/800/4M/2c/4.8 QPI/80W 594889-001 Optional2 Intel Xeon EP 2.26 GHz, 8M, 60W 504584-001 Optional2 Intel Xeon EP L5506 2.
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il servizio. 1 Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP, potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço. 1 Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto.
○ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days a week. For continuous quality improvement, calls may be recorded or monitored. ○ If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more information about Care Packs, refer to the HP website at http://www.hp.com/. • Outside North America, call the nearest HP Technical Support Phone Center.
Removal and Replacement Procedures This chapter provides subassembly/module-level removal and replacement procedures for the HP ProLiant SL160z G6 server. Review the specifications of a new component before installing it to make sure it is compatible with the server. When you integrate new components into the system, record its model and serial number, and any other pertinent information for future reference.
Pre-Installation Procedure Perform the steps below before you open the server or before you remove or replace any component. WARNING: Failure to properly turn off the server before you open the server or before your start installing/ removing components may cause serious damage as well as bodily harm. 1. Turn off the server and all the peripherals connected to it. 2.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them. CAUTION: Do not operate the server for long periods with the access panel open or removed. Operating the server in this manner results in improper airflow and improper cooling that can lead to thermal damage. CAUTION: The following rack-mount instructions shall be paid attention to.
This symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. weight1_kg weight1_lb This symbol indicates that the component exceeds the recommended weight for one individual to handle safely.
Figure 1 Removing the top cover To reinstall the top cover: 1. Align the top cover to the chassis and then slide it towards the front panel to position it into place. 2. Fasten the two rear screws to secure the top cover to the chassis. Figure 2 Reinstalling the top cover Cable Management Always follow good cable management practices when working inside the computer. • • Keep cables away from major heat sources like the heat sink.
• When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the wires. • • • • • Some flat ribbon cables come pre-folded. Never change the folds on these cables. Do not sharply bend any cable. A sharp bend can break the internal wires. Never bend a SATA data cable tighter than a 30 mm (1.18 in) radius. Never crease a SATA data cable. Do not rely on components like the drive cage, power supply, or system cover to push cables down into the chassis.
Table 2 Node Cable connections Cable To System Board Designator Internal USB connector Node USB J69 SATA cable connector Node SATA1 J57 SATA cable connector Node SATA2 J58 SATA SGPIO cable Node SGPIO connector J39 Cable To System Board Designator RJ45 cable connector RJ45 board J1 UID cable connector UID LED J12 Fan connector 1 Fan 1 J7 Fan connector 2 Fan 2 J6 Fan connector 3 Fan 3 J11 Fan connector 4 Fan 4 J10 Table 3AC power board connection Hard Drives The Server can
To install a Hard Drive: 1. Unlock the HDD carrier latch. 2. Rotate the HDD carrier handle up. 3. Insert the HDD carrier and align the four pins. 4. Rotate the HDD carrier handle down and then lock the HDD carrier latches. Figure 5 Installing the hard drive assembly To remove hard drive: 1. Slide the HDD carrier latches to unlock the HDD handle. 2. Raise the HDD handle. 3. Lift the HDD assembly out of the tray.
System Board Configuration Processor HP ProLiant SL160z G6 Server, with 2 nodes, supports four-processor operation. With two processors installed, each node supports boot functions through the processor installed in processor socket 1. However, if processor 1 fails, the system automatically boots from processor 2 and provides a processor failure message. The processor socket supports Quad-Core Intel®Nehalem 5500 Series processor and Intel®Xeon® 5600 Series processor.
CAUTION: Place heat sink down in an upright position with the thermal patch facing upward. Do not let the thermal patch touch the work surface. Figure 8 Removing the Heat Sink assembly IMPORTANT: If the heat sink has been removed for any reason on a previously installed processor, it is critical that you apply more thermal interface material to the integrated heat spreader on the processor to ensure proper thermal bonding between the processor and the heat sink. To remove a processor: 1.
Figure 10 Removing the processor 3. Carefully rotate the tool, and then push in and release the tabs to secure the processor in the tool. Figure 11 Securing the processor CAUTION: To avoid damage to the processor, do not touch the bottom of the processor, especially the contact area.
To install the new processor: 1. Carefully insert the processor into the processor installation tool. Handle the processor by the edges only, and do not touch the bottom of the processor, especially the contact area.
2. Be sure the tool is oriented correctly. Align the processor installation tool with the socket, and then install the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. Figure 13 Installing the processor CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To avoid damage to the system board: • Never install or remove a processor without using the processor installation tool. • Do not touch the processor socket contacts.
Figure 14 Removing the processor installation tool 4. Close the processor socket retaining bracket and the processor locking lever. CAUTION: Be sure to close the processor socket retaining bracket before closing the processor locking lever. The lever should close without resistance. Forcing the lever closed can damage the processor and socket, requiring system board replacement.
To apply the thermal grease compound: 1. Use a clean cloth dipped in rubbing alcohol to clean the contact surface on the heat sink and on the new processor. Wipe the contact surfaces several times to make sure that no particles or dust contaminants are evident. 2. Apply the thermal grease compound to the CPU contact surface. CAUTION: HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant server. 3.
Figure 17 Installing the heat sink Memory HP ProLiant SL160z G6 server has thirty-two DIMM slots that support up to 256 GB maximum system memory. You must adhere to the following guidelines when adding or replacing memory modules: • • • For 4P system, both physical processors in each node must be of the same type and speed. Use 1066/1333 MHz Registered/Unbuffered ECC DDR3 Memory.
Figure 19 Removing a Memory module CAUTION: Place the memory module on a static-dissipating work surface or inside of an anti-static bag. To install a memory module: 1. Align the notch on the bottom edge of the module with the keyed surface of the DIMM slot and then press the module fully into the slot. 2. Firmly press the holding clips inward to secure the memory module in place. Figure 20 Installing a Memory module CAUTION: The memory slots are structured to ensure proper installation.
PCI Expansion Cards System Board PCI Expansion Slots There are one X16 and one X4 PCIe Riser slots on the system boards.
Figure 22 PCIe Riser Card X16 Connectors Location Figure 23 PCIe Riser Card X4 Connectors Location • Single-Slot PCIe riser card (x16 slot) To remove the PCIe riser card with the bracket: 1. Loosen the screw securing the riser card bracket to the chassis. 2. Pull the riser card away together with the bracket.
Figure 24 Removing the PCIe riser card To remove the X16 riser card from the bracket: 1. Remove the two screws securing the riser card to the bracket. 2. Pull the riser card away from the bracket. Figure 25 Removing the PCIe riser card To install the PCIe X16 riser card to the bracket: 1. Align the riser card with the bracket. 2. Fasten the two screws to secure the riser card to the bracket.
Figure 26 Installing PCIe riser card to the bracket To install the riser card with the bracket into the motherboard: 1. Align the riser card connector with the slot on the motherboard and then insert the assembly into the slot. 2. Fasten the screw to secure the bracket to the chassis. Figure 27 Installing the PCIe riser card with bracket • Single-Slot PCIe riser card (x4 slot) To remove the PCIe X4 riser card with the cage: 1.
Figure 28 Remove the PCIe X4 Cage To remove the PCIe X4 riser card: 1. Remove the screw that secures the riser card to the cage. 2. Pull the PCIe card out and away from the PCIe X4 cage. Figure 29 Removing the Riser Card X4 To install the PCIe riser card to the cage: 1. Align the PCIe X4 riser card to the PCIe X4 Cage. 2. Install and tighten the two screws that secure the riser card to the riser card cage.
Figure 30 Reinstalling the PCIe riser card X4 To install the PCIe X4 cage: 1. Align the riser card cage beside the PCIe X4 connecter on the main board 2. Install and tighten the two screws to secure the riser card cage to the chassis. Figure 31 Reinstalling the PCIe Riser Card X4 To remove the PCIe card: 1. Remove the screw that secures the PCIe card. 2. Open the PCIe latch. 3. Pull the PCIe card back and away from the PCIe riser card. 4. Slide the PCIe bracket across the chassis. 5.
Figure 32 Removing the PCIe card To install the PCIe card: 1. Open the PCIe latch. 2. Remove PCIe card or blank. 3. Push the PCIe card into riser card connector. 4. Close PCIe latch. 5. Install screws. Figure 33 Installing the PCIe card System Battery The server uses nonvolatile memory that requires 2 batteries to retain system information when power is removed. This 3-volt lithium coin cell battery is located on the system board.
Figure 34 System battery location WARNING: Note the following reminders when replacing the system battery: • Replace the battery with the same type as the battery recommended by HP. Use of another battery may present a risk of fire or explosion. • A risk of fire and chemical burn exists if the battery is not handled properly. Do not disassemble, crush, puncture, or short external contacts, or expose the battery to temperatures higher than 60°C (140°F). • Do not dispose of used battery in water or fire.
Figure 35 Replacing the battery System Board Removal and Replacement Procedure To remove the system board: Remove the tray with the system board: 1. Press the tray latch to release the tray handle. 2. Rotate the tray handle to disengage the power connector. 3. Pull the tray assembly out of the chassis. Figure 36 Removing the tray with system board Remove the system board from the tray: 1. Remove the nine screws that secure the system board to the tray. 2. Release the system board from the tray.
Figure 37 Removing the 160 system board from the tray To replace the 160 system board: 1. Put the system board in the chassis. The nine screw holes on the chassis should align with the system board. 2. Fasten the nine screws on the system board to secure the system board to the chassis. Figure 38 Reinstalling the160 system board to the tray To replace the tray with system board: 1. Push the tray assembly into the tray bay until it stops. 2. Rotate the tray handle until the tray latch catches.
Figure 39 Installing the tray with system board into the chassis Power Supply Unit (PSU) Located on the rear panel of the server power supply is a standard auto ranging 750watt PSU with PFC (power factor correction) function. Figure 40 Power supply unit WARNING: Take note of the following reminders to reduce the risk of personal injury from electric shock hazards and/or damage to the equipment.
3. Slide the power supply into the power supply bay until it snaps into place. Figure 41 Installing the Power supply (1) Figure 42 Installing the power supply (2) To remove the power supply: 1. Press the blue colored handle. 2. Slide the power supply out of the power supply cage. 3. Install the power supply blank into the place where power supply was seated.
Figure 43 Removing the power supply System Fan The server can support either 3 or 4 system fans located at the chassis’ rears fan cage. Fan 1 is optional. You can refer to Fan option Installation instructions for details. The figure below identifies the system fans by their device number and shows their corresponding cable connections.
A new system fan can be installed to allow the server to operate properly in case a default system fan becomes defective. To remove the system fan: 1. Disconnect the fan cable from its corresponding board connector. 2. Lift the system fan away from the chassis. Figure 45 Removing the system fan To replace the system fan: 1. Insert the system fan into the fan bracket. 2. Connect the fan cable to its corresponding board connector.
Connectors, Switches, and LEDs This chapter contains illustrations and tables identifying and describing the connectors, switches, buttons, and LED indicators located on the front panel, rear panel, system board and hard drives of the HP ProLiant SL160z G6. Connectors and Components Front Panel Components Figure 47 Front panel components Item Description 1a Tray handle 1b Tray latch 2 Serial Port 3 Video Port 4 Top: USB 2.0 Port Bottom: USB 2.
Item Description 10 Power Button Rear panel components Figure 48 Rear panel components Item Description 1 RJ45 port 2 Power supply 2 3 Power supply 1 4 UID LED Connectors, Switches, and LEDs 57
System board components Figure 49 System board components Item Designator Description 1 J2 Serial Port (COM1) 2 J1 VGA port 3 J8 USB PORT 4 J7 NIC Port 5 J21,J22,J79; J23,J24,J78; J25,J26,J77 MEMORY DIMM CONN 6 SW1 UID BUTTON 7 J90 IPMI CONN 8 J18 PCIE-X4 LP RISER SLOT 9 J17 PCIE-X16 FH/FL RISER SLOT A 10 J27 Jumper 11 J29 TPM CONN 12 J31 PCIE-X4 FH/FL RISER SLOT B Connectors, Switches, and LEDs 58
Item Designator Description 13 J11 MINI SAS CONN 14 J69 USB4 15 J3 Storage card slot 16 J56 LCD Connector 17 B1 BATTERY 18 J82 PS backplane connector 19 J65 BP I2C CONN 20 J42 FRONT PANEL CONN 21 J67,J68,J70, J62,J71 FAN CONN 22 J64 12V POWER CONN 23 J57,J58 SATA HDD CONN 24 J63 FAN CONN 25 J47,J47,J76: J46,J45,J75: J43,J44,J74 MEMORY DIMM CONN 26 J51 SYSTEM POWER CONN 27 U73 Processor 1 Socket 28 J60 12V POWER CONN 29 U34 Processor 2 Socket CAUTION: The
LED Indicators This section contains illustration and descriptions of internal and external status LED indicators located on the: • • Front panel Rear panel These LED indicators aid in problem diagnosis by indicating the status of system components and operations of the server. Front panel LED indicators The front panel LED indicators allow constant monitoring of basic system functions while the server is operating.
Table 5 Health LED indicator status Components Status Description Off System is off and there is no failure prior to system power off Figure 51 UID LED indicator location Table 6 Type table name here Components Status Descriptions UID LED indicator for Node 1 Blue Identification Blue(Blinking) System is being remotely managed Off Off Blue Identification Blue(Blinking) System is being remotely managed Off Off UID LED indicator for Node 2 Power LED Indicator The power status of the serv
Figure 52 Power LED indicator location Table 7 Power/system health LED indicator status Component Status Description Power LED indicator for Node 1 Steady green The server is operating normally. Steady Amber The server is system off or in hibernation with A/C power. Steady red Critical event happens to the server. Please refer to SEL for details. Off The server is system off without A/C power. Steady green The server is operating normally.
Figure 53 LAN/LED indicator location Table 8 LAN/LED indicator states Item Component Status Description 1 LAN activity status LED indicator Flashing green Ongoing network data activity. Off No network data activity or no connection. Steady green The LAN connection is using a GbE link. Steady amber The LAN connection is using 10Mbps/100 Mbps link. Off No connection.
Diagnostic tools and Setup Utilities This chapter provides an overview of the Power-on Self-Test (POST), the POST error messages, and BIOS, SAS and SATA setup utilities. BIOS Software The server uses BIOS to boot up the system. BIOS software is a ROM-based firmware that allows reliability, manageability, and connectivity for server platforms. This software contains a set of programs permanently stored in an EEPROM chipset located on the system board.
Navigating through the Setup Utility Use the keys listed in the legend bar on the right of the Setup screen to navigate through the various menu and submenu screens of the Setup Utility. Table 9 lists these legend keys and their respective functions. Table 9 Setup Utility Navigation Keys Key Function ← and → To move between selections on the menu bar. ↑ and ↓ To move the cursor to the field you want. The currently selected field is highlighted.
Figure 54 Setup Utility General Help screen Press F1 to get the general help message box. Setup Utility Menu Bar The BIOS Setup Utility provides a menu bar with the menu selections. The menu bar choices are described in the topics below. Main Menu Figure 55 Main menu of BIOS Setup Utility Use this menu to set the system time and date, and configure of the following items: • View BIOS build date and version.
• • • • • • • View CPU type / CPU speed /CPU physical count information. View System memory size. View System serial number. View MAC address for the embedded NIC. Set Server Asset Tag. Set system time and date. Set boot features: ○ ○ ○ ○ Enable or Disable POST Speed up. Enable or Disable Bootup Num-Lock. Set restore on AC power loss options, such as last state, power off, and power on. If BIOS displays an error message, set POST F1 Prompt for selections, such as delayed, enabled, or disabled.
• Super IO Configuration–You can use this screen to select options for the Super I/O settings. Use the up and down keys to select an item. Use the and keys to change the value of the selected option. The settings are described on the following pages. • USB Configuration –These items control various USB devices. From the USB configuration screen, press to access the submenu for the USB BIOS Support. Use the up and down keys to select an item.
• Watchdog Configuration –Select Watchdog Configuration in the left frame of the screen and press to go to the submenu for that item. That will display POST Watchdog Timer Action, BMC Watch Dog Time Out; you can change the default value. • Serial Port Configuration –Select Serial Port Configuration in the left frame of the screen to go to the submenu for that item. Then you can press Enter to enter its submenu.
• Change Admin Password --- Allows you to access and change all settings in the Setup Utility. The administrator password allows you to configure access for system users. To set a new administrator password: 1. In the Security screen, select a set password field - Change Admin Password, and then press Enter. 2. Type a new password in the Enter New Password box. 3. The password may consist of up to six characters. Alphanumeric characters (A-Z, a-z, 0-9) are recommended to avoid system error. 4.
Exit Menu Figure 61 Exit menu of the BIOS Setup Utility Use this menu to save changes or discard changes. When you save and exit, the server reboots. • Save Changes and Exit --- Save the changes you have made and exit the BIOS Setup Utility. (You can also press F10 key.) • Discard Changes and Exit --- Exit the BIOS Setup Utility without saving the changes you have made. (You can also press Esc key.) • • Discard Changes --- Discard any changes you have made. (You can also press F7 key.
Clear CMOS You may need to clear the Setup configuration values (CMOS) if the configuration has been corrupted, or if incorrect settings made in the Setup Utility have caused error messages to be unreadable. To clear CMOS: 1. Perform the Pre-Installation Procedure. 2. If necessary, remove any accessory boards or cables that prevent access to the system configuration switch. 3. Locate the system configuration button (J27-A) on the system board. 4. Press the button. AC power must not be connected. 5.
POST Errors Message Definition Whenever a non-fatal error occurs during POST, an error message describing the problem appears onscreen. These error messages are displayed in normal video (white text on black background), and show the details of the error. The following is an example of a POST error message: 012 --- CMOS Date/Time not set Table 10 lists the most common POST error messages with their corresponding troubleshooting recommendation.
Table 10 POST error message 601 Error: BMC Not Responding 040 Refresh timer test failed 048 Password check failed 00B CMOS Memory Size Wrong 010 Floppy Controller Failure 00C RAM R/W test failed 003 CMOS Battery Low 701 Insufficient Runtime space for MPS data. System may operate in PIC or Non-MPS mode. 702 No enough APIC ID in range 0-0Fh can be assigned to IO APICs. (Re-assigning CPUs' local APIC ID may solve this issue) MPS Table is not built! System may operate in PIC or Non-MPS mode.
Physical and Operating Specifications This chapter provides physical and operating specifications for the HP ProLiant SL160z G6 server. Specifications include: System Unit Table 11 Hardware Specifications Item Components Processor socket Intel 1366pin FCLGA Processor support Quad-Core Intel® Nehalem 5500 Series processor Intel®Xeon® 5600 Series processor. Chipset Intel® Tylersburg 36D /Intel ICH10R Hardware monitoring device IPMI 2.
Table 11 Hardware Specifications Item Components Status LED indicators Front panel Rear Panel System Board • Power/system health status • UID status • • • • • NIC activity LAN activity LAN link status Power/system health status UID status • Auxiliary power indicators Power Supply unit (PSU) 750W Redundant, power supply Thermal solution Four 80mm system fans Table 12 Physical Dimensions Item Description System board platform ATX (Advanced Technology Extended) System board dimension 17.
Table 13 Environmental Specifications Item Description Thermal output (maximum operating) 392 W/hr Acoustic emissions LWad: 6.7 Bels Normal configuration (operating at room temperature) LWad: 6.7 Bels (Idle at room temperature) Table 14 Hot-Plug Power Supply Specifications Item Description Dimensions (H x W x D) 38.48 mm x 86.36 mm x 190.52 mm Weight (approximate) 1.
Index hard drives, 32 A AC power power-down procedures, 28 B battery replacement warnings, 50 BIOS Setup Utility accessing, 65 additional navigation keys, 66 menu bar, 65 BIOS software Overview, 65 C memory, 41 PCI expansion cards, 43 power supply unit, 53 processor, 34 references, 25 system battery, 49 system fan, 55 top cover, 28 Hardware configuration tools, 25 hardware specifications I/O ports, 76 LAN controller, 76 memory, 76 cable management, 29 power supply unit, 77 CSR (customer self repair),
I Power-On Self Test POST error indicators, 73 improper airflow POST related troubleshooting, 75 caution, 26 recoverable POST errors, 74 L LAN controller, 76 processor applying thermal grease, 40 LED indicators installing, 40 LAN, 63 Power/system health, 62 M memory controller, 76 Memory Module spare part number, 20 memory modules guidelines for installation, 41 installing, 42 removing, 36 Processor heat sink spare part number, 21 processor socket specification, 76 Processors spare part number,
spare part number, 16 front panel, 57 rear panel, 58 Tray with system board removing, 51 System Unit replacing, 52 specifications, 76 T W thermal solution, 77 warnings top cover reinstalling, 29 removing, 28 battery replacement, 50 PSU replacement, 53 warranty, 5 Top cover Index 80
