hp StorageWorks edge switch 2/32 installation guide Part Number: AA-RSTZB-TE/958-000290-000 Second Edition (January 2003) This installation guide provides procedures for setting up, configuring, and managing the Edge Switch 2/32.
© Hewlett-Packard Company, 2003. All rights reserved. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. This document contains proprietary information, which is protected by copyright.
Contents About This Guide Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x Symbols in Text . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents HAFM Server Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–10 Ethernet Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11 Optional Kits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11 2 Installing and Configuring the Edge Switch 2/32 Summary of Installation Tasks . . . . . . . . . . . . . . . . . . . . . .
Contents Configure Port Addresses (S/390 Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure SNMP Trap Message Recipients . . . . . . . . . . . . . . . . . . . . . . . . . . Configure and Enable E-mail Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . Configure and Enable Call-Home Features . . . . . . . . . . . . . . . . . . . . . . . . . . Configure Threshold Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Procedures. . . . . . . . .
Contents Declaration of Conformity for Products Marked with FCC Logo—United States Only A–3 Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–3 Network and Serial Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–3 IEC EMC Statement (Worldwide) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A–4 Spécification ATI Classe A (France) . . . . . . . . . . . . . . . . . .
Contents 2–2 2–3 2–4 2–5 2–6 2–7 2–8 2–9 2–10 2–11 2–12 2–13 2–14 2–15 2–16 2–17 2–18 2–19 2–20 2–21 2–22 2–23 2–24 2–25 2–26 2–27 2–28 2–29 2–30 2–31 2–32 2–33 2–34 2–35 2–36 2–37 2–38 2–39 Connect To dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–8 Port Settings dialog box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9 HyperTerminal window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 2–40 2–41 2–42 2–43 2–44 2–45 2–46 2–47 2–48 3–1 3–2 3–3 3–4 Switch page—Identification tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–56 Switch page—Date/Time tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–57 Switch page—Parameters tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–59 Switch page—Fabric Parameters tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About This Guide About This Guide This installation guide provides information to help you: • Set up the Edge Switch 2/32. • Configure the Edge Switch 2/32. • Manage the Edge Switch 2/32. • Contact technical support for additional assistance.
About This Guide Document Conventions The conventions included in Table 1 apply. Table 1: Document Conventions Element x Convention Cross-reference links Blue text: Figure 1 Key names, menu items, buttons, and dialog box titles Bold File names, application names, and text emphasis Italics User input, command names, system responses (output and messages) Monospace font Variables Monospace, italic font Website addresses Sans serif font (http://thenew.hp.
About This Guide Symbols in Text These symbols may be found in the text of this manual. They have the following meanings. WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or data. IMPORTANT: Text set off in this manner presents clarifying information or specific instructions.
About This Guide Any surface or area of the equipment marked with these symbols indicates the presence of a hot surface or hot component. Contact with this surface could result in injury. WARNING: To reduce the risk of injury from a hot component, allow the surface to cool before touching. Power supplies or systems marked with these symbols indicate the presence of multiple sources of power.
About This Guide Getting Help If you still have a question after reading this manual, contact an HP authorized service provider or access our website: http://thenew.hp.com. HP Technical Support In North America, call technical support at 1-800-652-6672, available 24 hours a day, 7 days a week. NOTE: For continuous quality improvement, calls may be recorded or monitored. Outside North America, call technical support at the nearest location.
About This Guide xiv edge switch 2/32 installation guide
1 Introduction The HP StorageWorks Edge Switch 2/32 provides dynamic switched connections between Fibre Channel servers and devices in a storage area network (SAN) environment. SANs introduce the concept of server-to-device networking and multi-switch fabrics, eliminate requirements for dedicated connections, and enable the enterprise to become data centric. A SAN provides speed, high capacity, and flexibility for the enterprise, and is primarily based upon Fibre Channel architecture.
Introduction Edge Switch 2/32 Description The switch can be installed on a table or desk top, or mounted in an equipment cabinet or in any standard equipment rack. Multiple switches and the HAFM server communicate on a local area network (LAN) through one or more 10Base-T Ethernet hubs. One or more 24-port Ethernet hubs are optional and can be ordered with the switch.
Introduction Features The following sections describe the features of the Edge Switch 2/32: Error-Detection, Reporting, and Serviceability The switch provides the following error-detection, reporting, and serviceability features: • Light-emitting diodes (LEDs) on switch FRUs and adjacent to Fibre Channel ports that provide visual indicators of hardware status or malfunctions.
Introduction • Data collection through the Product Manager application to help isolate system problems. The data includes a memory dump file and audit, hardware, and engineering logs. • Simple network management protocol (SNMP) management using the Fibre Alliance MIB that runs on the HAFM server. Up to 12 authorized management workstations can be configured through the HAFM application to receive unsolicited SNMP trap messages. The trap messages indicate operational state changes and failure conditions.
Introduction Zones are grouped into zone sets. A zone set is a group of zones that is enabled (activated) or disabled across all switches in a multi-switch fabric. Only one zone set can be enabled at one time. Multi-Switch Fabrics A Fibre Channel topology that consists of one or more interconnected switches or switch elements is called a fabric. Operational software provides the ability to interconnect switches (through expansion port (E_Port) connections) to form a multi-switch fabric.
Introduction checking is done for pre-existing conditions and no prompts display to guide users through tasks. Refer to hp StorageWorks CLI reference guide for edge switches and directors. This manual provides details on the Product Manager application for the Edge Switch 2/32 only. Use this manual for the Product Manager installed on an HAFM server. This manual does not cover the Embedded Web Server interface or CLI.
Introduction 1 1 2 2 3 Cooling fan (4) Power supply (2) 2 3 3 Power switches on power supplies (2) Figure 1–3: Edge Switch 2/32 (Rear View) SFP Transceivers A single-mode or multi-mode fiber-optic cable attaches to a port through a pluggable small form factor (SFP) transceiver. The SFP provides a duplex LC interface, and can be detached from the switch port for easy replacement.
Introduction Each power supply has a separate CTP connection to allow for independent AC power sources. The power supplies are input-rated at 100 to 230 volts alternating current (VAC). Power supply requirements are listed in Appendix B. Connectors and Indicators Connectors and indicators include the: • Initial machine load (IML) button. • Ethernet LAN connector. • Green power (PWR) and amber system error (ERR) LEDs. • Green and amber status LEDs associated with FRUs. • RS-232 maintenance port.
Introduction Power and System Error LEDs The PWR LED, as shown in Figure 1–2 illuminates when the switch is connected to facility AC power and powered on. If the LED extinguishes, a facility power source, power cord, or power distribution failure is indicated. The ERR LED, as shown in Figure 1–2 illuminates when the switch detects an event requiring immediate operator attention, such as a FRU failure. The LED remains illuminated as long as an event is active.
Introduction • FRUs provide on-board diagnostic and monitoring circuits that continuously report FRU status to the HAFM and Product Manager applications. These applications provide system alerts and logs that display failure and diagnostic information at the HAFM server or a remote workstation communicating with the HAFM server. • The HAFM Services application that runs as a Windows 2000 service and provides an additional user interface to display operational status.
Introduction Although a configured switch operates normally without HAFM server intervention, an attached server should operate at all times to monitor switch operation, log events and configuration changes, and report failures. The HAFM server provides an auto-detecting 10/100 Mbps LAN connection, provided by an internal Ethernet adapter card. This LAN port attaches to the customer’s public intranet to allow access from remote user workstations.
Introduction 1–12 edge switch 2/32 installation guide
2 Installing and Configuring the Edge Switch 2/32 This chapter describes tasks to install, configure, and verify operation of the edge switch 2/32. The switch can be installed on a table or desk top, or mounted in any standard equipment rack. For a list of the factory-set defaults for the switch and the Reset Configuration option, refer to Appendix B. Summary of Installation Tasks Table 2–1 summarizes installation tasks for the switch, HAFM server, and Ethernet hub.
Installing and Configuring the Edge Switch 2/32 Table 2–1: Installation Task Summary (Continued) Task Number and Description Required or Optional Page Task 6: Configure the Switch to the HAFM Application Required if Task 5: HAFM Server (Optional) task was done. 2–13 Task 7: Record or Verify HAFM Server Restore Information Required if Task 5: HAFM Server (Optional) task was done. 2–13 Task 8: Verify Switch-to-HAFM Server Communication Required if Task 5: HAFM Server (Optional) task was done.
Installing and Configuring the Edge Switch 2/32 Installation Options The switch is installed in one of two configurations. The options are: • Table or desk top—one or more switches, an optional HAFM server, and an optional Ethernet hub are delivered and installed at the customer facility on a desk or table top. Ethernet cabling distance, and local area network (LAN) addressing issues must be considered.
Installing and Configuring the Edge Switch 2/32 Task 2: Unpack, Inspect, and Install the Switch The following paragraphs provide instructions to unpack and inspect the edge switch 2/32, and install it in a desktop or rack-mount configuration. Unpack and Inspect the Switch Unpack and inspect the switch: CAUTION: When you remove the switch from the carton, do not rest it on its rear window while examining it. To do so may break the FRU handles. 1.
Installing and Configuring the Edge Switch 2/32 4. Verify that the SFP optical transceivers are installed as required for your installation. 5. Connect the U.S. or country-specific (optional) AC power cords to the right (PS0) and left (PS1) receptacles at the rear of the chassis. WARNING: An HP-supplied power cord is provided for each switch power supply.
Installing and Configuring the Edge Switch 2/32 Task 3: Configure Network Information The edge switch 2/32 is delivered with the following default network addresses: • MAC address—the media access control (MAC) address is programmed into FLASH memory on the CTP card at the time of manufacture. The MAC address is unique for each switch, and should not be changed. The address is in xx.xx.xx.xx.xx.xx format, where xx is a hexadecimal pair.
Installing and Configuring the Edge Switch 2/32 Verify the type of LAN installation with the customer’s network administrator. If one switch is installed on a dedicated LAN, network addresses do not require change. If multiple switches are installed or a public LAN segment is used, network addresses must be changed to conform to the customer’s LAN addressing scheme.
Installing and Configuring the Edge Switch 2/32 Figure 2–1: Connection Description dialog box 5. Type edge switch 2-32 in the Name field and click OK. The Connect To dialog box displays, as shown in Figure 2–2.
Installing and Configuring the Edge Switch 2/32 6. Ensure the Connect using field displays COM1 or COM2 (depending on the serial communication port connection to the switch), and click OK. The Port Settings dialog box displays, as shown in Figure 2–3. Figure 2–3: Port Settings dialog box 7. Configure the Port Settings parameters as follows: — Bits per second—57600 — Data bits—8 — Parity—None — Stop bits—1 — Flow control—Hardware When the parameters are set, click OK. The HyperTerminal window displays. 8.
Installing and Configuring the Edge Switch 2/32 Figure 2–4: HyperTerminal window 9. At the C> prompt, type ipconfig and press Enter. The HyperTerminal window displays with configuration information listed as follows: — MAC Address — IP Address (default is 10.1.1.10, factory preset is 10.1.1.10) — Subnet Mask (default is 255.0.0.0). — Gateway Address (default is 0.0.0.0) Only the IP Address, Subnet Mask, and Gateway Address fields are configurable. 10.
Installing and Configuring the Edge Switch 2/32 11. Choose Exit from the File menu to close the HyperTerminal application. A message box displays, as shown in Figure 2–5. Figure 2–5: Disconnect Now dialog box 12. Click Yes. A message box displays, as shown in Figure 2–6. Figure 2–6: Save Session dialog box 13. Click No to exit and close the HyperTerminal application. 14. Power off the maintenance terminal: a. Choose Start > Shut Down. The Shut Down Windows dialog box displays. b.
Installing and Configuring the Edge Switch 2/32 2. Connect the remaining end of the Ethernet cable to the LAN as follows: a. If the switch is installed on a customer-supplied LAN segment, connect the cable to the LAN as directed by the customer’s network administrator. b. If the switch is installed on the HP-supplied Ethernet hub, connect the cable to any available port on the hub. 3.
Installing and Configuring the Edge Switch 2/32 Task 6: Configure the Switch to the HAFM Application To manage a new switch, it must be identified to the HAFM application. To identify the new switch: 1. Right-click in a blank area of the Product View page and select New or click Product on the menu bar and choose New. The New Product dialog box displays, as shown in Figure 2–7. Figure 2–7: New Product dialog box 2.
Installing and Configuring the Edge Switch 2/32 Task 8: Verify Switch-to-HAFM Server Communication Communication must be verified between the switch and the HAFM server (High Availability Fabric Manager and Product Manager applications). To verify switch-to-server communication: 1. At the Windows 2000 desktop, click HAFM at the task bar (bottom of the desktop) to maximize the Product View page. 2. At the Product View page, inspect the shape and color of the symbol behind the Edge Switch 2/32 icon.
Installing and Configuring the Edge Switch 2/32 Figure 2–8: Switch Hardware View page 4. Inspect switch status at the Hardware View page and perform one of the following steps: a. If the switch displays operational (no FRU alert symbols and a green circle at the alert panel), go to “Task 11: Set Switch Date and Time” on page 2–21. b.
Installing and Configuring the Edge Switch 2/32 • Fiber connection (FICON) management server (FMS) These features allow open systems or FICON host control of the switch and are mutually exclusive. Only one of these features can be installed at a time. Features are enabled through a feature key that is encoded to work with the serial number of a unique switch. A feature key is a case-sensitive alphanumeric string with dashes every four characters.
Installing and Configuring the Edge Switch 2/32 Figure 2–9: Configure Feature Key dialog box 3. Click New. The New Feature Key dialog box displays, as shown in Figure 2–10. Figure 2–10: New Feature Key dialog box 4. Type the OSMS feature key (case-sensitive xxxx-xxxx-xxxx-xx format) and click OK. The Enable Feature Key dialog box displays, as shown in Figure 2–11. Figure 2–11: Enable Feature Key dialog box 5. Click Activate to enable the OSMS feature key.
Installing and Configuring the Edge Switch 2/32 Configure FMS Feature Key Perform this procedure to configure the FMS feature key. This feature key enables host control of the switch from an IBM System/390 or zSeries 900 Parallel Enterprise server attached to a switch port. The server communicates with the switch through a FICON channel. To configure the FMS feature key: 1. Set the switch offline. 2. At the Hardware View page for the selected switch, choose Configure > Features.
Installing and Configuring the Edge Switch 2/32 Figure 2–14: Activate FMS feature key Task 10: Configure OSMS or FICON Management Server (Optional) Perform this task to configure the open systems management server or FICON management server. Only one management server can be configured at a time. Configure OSMS Perform this procedure to configure the open systems management server and enable OSI host control of the switch.
Installing and Configuring the Edge Switch 2/32 2. Allow or prohibit host (OSI server) control by selecting Host Control Prohibited. If a check mark displays, host control is prohibited. 3. Click Activate to enable a change and allow or prohibit open systems host control. Configure FMS Perform this procedure to configure the FICON management server and enable FICON host control of the switch.
Installing and Configuring the Edge Switch 2/32 • Active = Saved—when this option is enabled, the active configuration of logical port addresses is used when the IPL configuration file is updated. If a check mark displays, the Active = Saved option is enabled. 3. Select the appropriate country code page from the following Code Page list box, as shown in Table 2–3.
Installing and Configuring the Edge Switch 2/32 Figure 2–17: Configure Date and Time dialog box Set Date and Time Manually To set the switch date and time manually: 1. At the Configure Date and Time dialog box, click Periodic Date/Time Synchronization to deselect the option (no check mark in the box). The greyed out Date and Time fields activate. 2.
Installing and Configuring the Edge Switch 2/32 Periodically Synchronize Date and Time To set the switch to periodically synchronize date and time with the HAFM application: 1. Click Periodic Date/Time Synchronization to select the option (check mark in the box). The Date and Time fields are greyed out and not selectable. Perform one of the following options: • Click Activate to enable synchronization and close the Configure Date and Time dialog box.
Installing and Configuring the Edge Switch 2/32 • Configure switch ports. • Configure logical port addresses. • Configure SNMP trap message recipients. • Configure and enable e-mail notification. • Enable call-home notification. Configure Switch Identification Perform this procedure to configure the switch name, description, location, and contact person for the HAFM application. The information displays in multiple dialog boxes throughout the application.
Installing and Configuring the Edge Switch 2/32 c. Type a switch description of 255 alphanumeric characters or less in the Description field. d. Type the switch’s physical location (255 alphanumeric characters or less) in the Location field. e. Type the name of a contact person (255 alphanumeric characters or less) in the Contact field. 2. Click Activate to configure the switch identification and close the dialog box.
Installing and Configuring the Edge Switch 2/32 Figure 2–20: Configure Switch Parameters dialog box Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID. Change this value if the switch will participate in a multiswitch fabric. 1. Use information under “Switch Parameters” to change settings as required for parameters in this dialog box. 2. After you change settings, click the Activate button.
Installing and Configuring the Edge Switch 2/32 Preferred NOTE: To change this value, you must first set the switch offline. Choose Set Online State from the Maintenance menu to display the Set Online State dialog box, then click the Set Offline button. Be sure to set the switch back online after you change this value. Use this field to set the a unique domain ID for the switch. The default value is 1. Set a value between 1 and 31.
Installing and Configuring the Edge Switch 2/32 Enabling the rerouting delay ensures that frames are delivered in order through the fabric to their destination. If there is a change to the fabric topology that creates a new path (for example, a new switch is added to the fabric), frames may be routed over this new path if its hop count is less than a previous path with a minimum hop count.
Installing and Configuring the Edge Switch 2/32 • Use Open Systems mode for all other (non-FICON) Fibre Channel environments. Configure Fabric Operating Parameters Use procedures in this section to set parameters on the switch for fabric operation through the Configure Fabric Parameters dialog box. These operating parameters are stored in NV-RAM on the switch. 1. The switch must be offline to change parameters in this dialog box.
Installing and Configuring the Edge Switch 2/32 Figure 2–21: Configure Fabric Parameters dialog box NOTE: Ordinarily, you do not need to change values in this dialog box from their defaults. The only exception is the Preferred Domain ID. Change this value if the switch will participate in a multiswitch fabric. 3. Use information under “Fabric Parameters” to change settings as required for parameters in this dialog box. 4. After you change settings, click the Activate button. 5.
Installing and Configuring the Edge Switch 2/32 R_A_TOV Configure resource allocation time-out value (R_A_TOV) in tenth-of-a-second increments. This variable works with the error detect time-out value (E_D_TOV) variable to control the switch’s behavior when an error condition occurs. Resources are allocated to a circuit when errors are detected and are not released for reuse until the time set by the R_A_TOV value expires. The default value is 100 tenths (10 seconds).
Installing and Configuring the Edge Switch 2/32 • If you have three switches and set two to Default and one to Never Principal, the switch with the Default setting and the lowest WWN becomes the principal switch. At least one switch in a multiswitch fabric needs to be set as Principal or Default. If all of the switches are set to Never Principal, all of the interswitch links (ISLs) will segment.
Installing and Configuring the Edge Switch 2/32 b. Click Blocked check box to block or unblock a port. A check mark in the box indicates the port is blocked. Blocking the port prevents the attached device from communicating with the switch. A blocked port continuously transmits the offline sequence (OLS), as shown in Figure 2–22. Figure 2–22: Configure Ports dialog box (open systems mode) c. Click 10-100 km to enable extended distance buffering for a port.
Installing and Configuring the Edge Switch 2/32 A right-click in the Speed column allows you to choose from a menu to set all ports to 1 Gb/sec, 2 Gb/sec, or Navigate. g. Port Binding—Click this check box to display a check mark and enable WWN binding for the port. This allows only a specific device to attach to the port. This device is specified by the WWN or nickname entered into the Bound WWN column.
Installing and Configuring the Edge Switch 2/32 Figure 2–23: Configure Ports dialog box (S/390 mode) a. Click 10-100 km to enable extended distance buffering for a port. A check mark in the box indicates extended distance operation up to 100 kilometers (through repeaters) is enabled. b. Click LIN Alerts to enable or disable LIN alerts for a port. A check mark in the box indicates alerts are enabled.
Installing and Configuring the Edge Switch 2/32 e. Bound WWN—Enter a World Wide Name (WWN) in the proper format (xx.xx.xx.xx.xx.xx.xx.xx) or a nickname configured through the Product Manager application. The device with this WWN or nickname will have exclusive attachment to the port if WWN Binding is enabled. If a valid WWN or nickname is not entered in this field, but the WWN Binding check box is checked (enabled), then no devices can connect to the port.
Installing and Configuring the Edge Switch 2/32 Figure 2–24: Configure Addresses—Active dialog box a. Select a blank Name field and type a descriptive port name of 24 or fewer alphanumeric characters. Use a name that reflects the device connected to the port. b. Click Blocked to block or unblock a port. A check mark in the box indicates the port is blocked. Blocking the port prevents the attached device from communicating with the switch. A blocked port continuously transmits the offline sequence (OLS).
Installing and Configuring the Edge Switch 2/32 • Prohibit or allow connections for an entire row (row 0C is prohibited in the Configure Addresses—Active dialog box example), • Prohibit or allow connections for all switch ports, • Block or unblock all switch ports, or • Clear connectivity restrictions for all switch ports. 3. At the CUP Name field, type a control unit port description of 24 or fewer alphanumeric characters (optional).
Installing and Configuring the Edge Switch 2/32 Configure SNMP Trap Message Recipients Perform this procedure to configure community names, write authorizations, and network addresses and for up to 12 SNMP trap message recipients. A trap recipient is a management workstation that receives notification (through SNMP) if a switch event occurs. To configure SNMP trap recipients: 1. At the Hardware View page for the selected switch, choose Configure > SNMP Agent.
Installing and Configuring the Edge Switch 2/32 2. To enable transmission of trap messages to configured SNMP management workstations, click Enable Authorization Traps. A check mark displays in the box when transmission is enabled, as shown in Figure 2–27. Figure 2–27: Configure SNMP dialog box—Enable Authorization Traps 3. Click Activate to save the information and close the dialog box.
Installing and Configuring the Edge Switch 2/32 Figure 2–28: Configure E-Mail dialog box a. Type the IP address or DNS host name of the SMTP server in the SMTP server field. Use 64 alphanumeric characters or less. It is recommended the IP address be used. b. For the E-Mail Addresses fields, type the e-mail addresses of up to five recipients who should be informed of system events. Use 64 alphanumeric characters or less for each entry. 2.
Installing and Configuring the Edge Switch 2/32 Configure and Enable Call-Home Features There are two call-home features available, and only one is installed when the HAFM application is installed on the HAFM server. To learn more about configuring Call-Home features, refer to the hp StorageWorks HAFM server installation guide.
Installing and Configuring the Edge Switch 2/32 Procedures Use the following procedures to create a new threshold alert, or to modify, activate, deactivate, or delete an alert. Create New Alert 1. At the Hardware View for the selected switch, choose Configure > Threshold Alerts. The Configure Threshold Alerts dialog box displays, as shown in Figure 2–29.
Installing and Configuring the Edge Switch 2/32 2. Click New. The New Threshold Alert dialog box displays, as shown in Figure 2–30. Figure 2–30: New Threshold Alerts dialog box—first screen 3. Enter a name from one to 64 characters in length. All characters in the ISO Latin-1 character set, excluding control characters, are allowed. 4. Select one of the following options from the drop-down list under the Name field: 2-44 • Rx Throughput.
Installing and Configuring the Edge Switch 2/32 5. Click Next. A new screen displays with additional parameters. The name configured for the alert displays at the top of the screen. Click Previous to return to the previous screen, as shown in Figure 2–31. Figure 2–31: New Threshold Alerts dialog box—second screen 6. Enter a percentage from 1 through 100 for % utilization. When throughput reaches this percentage of port capacity, a threshold alert will occur. 7.
Installing and Configuring the Edge Switch 2/32 9. Click Next. A new screen displays for selecting ports for the alerts, as shown in Figure 2–32. Figure 2–32: New Threshold Alerts dialog box—third screen 10. Either select Port Type or Port List. 2-46 • If you select Port Type, selecting either E_Ports or F_Ports will cause this alert to generate for all ports configured as E_Ports or F_Ports respectively.
Installing and Configuring the Edge Switch 2/32 11. Click Next. A final screen displays to provide a summary of your alert configuration. To make any changes, backwards and forwards through the configuration screens by selecting Previous and Next, as shown in Figure 2–33. Figure 2–33: New Threshold Alerts dialog box—summary screen 12. Select Finish. The Configure Threshold Alerts dialog box displays listing the name, type, and state of the alert that you just configured.
Installing and Configuring the Edge Switch 2/32 Figure 2–34: Configure Threshold Alerts dialog box—alerts activated Modify an Alert Use the following steps to modify an existing threshold alert configuration. 1. Choose Configure > Threshold Alerts. The Configure Threshold Alerts dialog box displays. 2. Select the alert that you want to modify by clicking the alert information in the table. 3. If the alert is active, click Deactivate, then select the alert information in the table again. 4. Click Modify.
Installing and Configuring the Edge Switch 2/32 6. Click Next when you are done. A Modify Threshold screen displays where you can change the % utilization, cumulative minutes for the threshold to occur before notification, and the time interval for measuring throughput and for alert notification. 7. Make appropriate changes, then continue through the Modify Threshold screens, making changes as necessary, until the summary screen displays showing the alert configuration. 8.
Installing and Configuring the Edge Switch 2/32 Task 13: Test Remote Notification (Optional) If the call-home and e-mail notification features are enabled, set up the HAFM application to test these remote notification features. Because the features are configured at the HAFM application, call-home and e-mail notification are enabled for multiple switches or HP managed products. To test remote notification: 1.
Installing and Configuring the Edge Switch 2/32 Task 14: Back Up HAFM Configuration Data It is important to back up the HAFM configuration data. This data is used to restore the HAFM server operating environment in case of hard drive failure. Refer to the hp StorageWorks HAFM server installation guide for instructions on backing up the HAFM configuration data. Once the HAFM configuration data is backed up, go to “Task 16: Cable Fibre Channel Ports” on page 2–69.
Installing and Configuring the Edge Switch 2/32 3. At the browser, enter the IP address of the switch as the internet uniform resource locator (URL). Use the default IP address of 10.1.1.10, the factory preset of 10.1.1.10, or the IP address configured while performing “Task 3: Configure Network Information” on page 2–6. The Username and Password Required dialog box displays, as shown in Figure 2–37.
Installing and Configuring the Edge Switch 2/32 4. Type the default user name and password. NOTE: The default user name is Administrator and the default password is password. The user name and password are case-sensitive. 5. Click OK. The Embedded Web Server interface opens with the View window displayed, as shown in Figure 2–38.
Installing and Configuring the Edge Switch 2/32 Configure Switch Ports Perform the procedure in this section to configure names and operating characteristics for the switch ports. To configure one or more ports: 1. At the View window, click Configure at the left side of the window. The Configure window opens with the Ports tab displayed. a. For each port to be configured, type a port name of 24 alphanumeric characters or less in the associated Name field.
Installing and Configuring the Edge Switch 2/32 c. Choose the check box in the 10-100 km column to enable extended distance buffering for a port (default is disabled). A check mark in the box indicates extended distance operation up to 100 kilometers (through repeaters) is enabled. d. Select a Type field and choose generic port (G_Port), fabric port (F_Port), or expansion port (E_Port) from the list box.If F_Port or E_Port is selected, the port will only operate as the port type selected.
Installing and Configuring the Edge Switch 2/32 Figure 2–40: Switch page—Identification tab a. Type a switch name of 24 alphanumeric characters or less in the Name field. Each switch should be configured with a unique name. If the switch is installed on a public LAN, the name should reflect the switch’s Ethernet network DNS host name. For example, if the DNS host name is hpes232.hp.com, then enter hpes232. b. Type a switch description of 255 alphanumeric characters or less in the Description field. c.
Installing and Configuring the Edge Switch 2/32 Configure Date and Time Perform this procedure to configure the effective date and time for the switch. To set the date and time: 1. At the Configure window, click the Switch tab, then select Date/Time tab. The Switch page displays with Date/Time tab selected (highlighted red), as shown in Figure 2–41. Figure 2–41: Switch page—Date/Time tab a.
Installing and Configuring the Edge Switch 2/32 Configure Switch and Fabric Parameters Perform this procedure to configure the following switch and fabric operating parameters: Buffer-to-Buffer Credit (BB_Credit), Error Detect Time Out Value (E_D_TOV), and Resource Allocation Time Out Value (R_A_TOV), preferred domain ID and switch priority. Configure Switch Parameters The switch must be set offline to configure operating parameters. To configure the parameters: 1. Set the switch offline as follows: a.
Installing and Configuring the Edge Switch 2/32 Figure 2–42: Switch page—Parameters tab a. At the Preferred Domain ID field, type a value between 1 and 31 (default is 1). The domain ID uniquely identifies each switch in a fabric. All fabric-attached switches must have unique domain IDs. If the value is not unique, the E_Port connection to the switch segments and the switch cannot communicate with the fabric. b. Insistent Domain: This option is not supported unless the SANtegrity feature is installed.
Installing and Configuring the Edge Switch 2/32 c. Click the Rerouting Delay check box to enable or disable the option. If a check mark displays, the option is enabled. If rerouting delay is enabled, traffic is delayed through a fabric by the specified E_D_TOV time. This delay ensures Fibre Channel frames are delivered to their destination in order, even if a change to the fabric topology creates a new (shorter) transmission path. d.
Installing and Configuring the Edge Switch 2/32 Figure 2–43: Switch page—Fabric Parameters tab a. At the BB_Credit field, type a value between 1 an 60 buffers. The default is 16. Use a value of 60 buffers only for extended distance port operation. b. At the R_A_TOV field, type a value between 10 through 1200 tenths of a second (one through 120 seconds). The default is 10 seconds (100 tenths). All fabric-attached switches must be set to the same R_A_TOV.
Installing and Configuring the Edge Switch 2/32 — HP Fabric 1.0. Default. Select this mode if the fabric contains only HP switches and switches that are operating in HP Fabric 1.0 mode. — Open Fabric 1.0. Select this mode if the fabric contains HP directors and switches, as well as other open-fabric compliant switches. Select this mode for managing heterogeneous fabrics. 5. Click Activate to save the information.
Installing and Configuring the Edge Switch 2/32 Figure 2–44: Switch page—Network tab a. At the IP Address field, type the new value as specified by the customer’s network administrator (default is 10.1.1.10, factory preset is 10.1.1.10). b. At the Subnet Mask field, type the new value as specified by the customer’s network administrator (default is 255.0.0.0). c. At the Gateway Address field, type the new value as specified by the customer’s network administrator (default is 0.0.0.0).
Installing and Configuring the Edge Switch 2/32 3. Click Activate to save the information. The following message box displays, as shown in Figure 2–45. Figure 2–45: Network configuration changes activated 4. Update the address resolution protocol (ARP) table for the browser PC. a. Choose File >Exit to close the Embedded Web Server and browser applications. The Windows desktop displays. b. Choose Start > Programs > Command Prompt. A disk operating system (DOS) window displays. c.
Installing and Configuring the Edge Switch 2/32 7. Type the default user name and password. NOTE: The default user name is Administrator and the default password is password. The user name and password are case-sensitive. 8. Click OK. The Embedded Web Server interface opens with the View window displayed. Configure SNMP Trap Message Recipients Perform this procedure to configure community names, write authorizations, and network addresses and for up to 6 SNMP trap message recipients.
Installing and Configuring the Edge Switch 2/32 Figure 2–46: Management page—SNMP tab a. For each trap recipient to be configured, type a community name of 32 alphanumeric characters or less in the associated Community Name field. The community name is incorporated in SNMP trap messages to ensure against unauthorized viewing or use. b. Click the check box in the Write Authorization column to enable or disable write authorization for the trap recipient (default is disabled).
Installing and Configuring the Edge Switch 2/32 3. Click Activate to save the information. The message Your changes to the SNMP configuration have been successfully activated displays. Configure User Rights Perform this procedure to configure the administrator-level and operator-level passwords used to access the Embedded Web Server interface through the Username and Password Required dialog box. To configure passwords: 1. At the Configure window, click the User Rights tab. The User Rights page displays.
Installing and Configuring the Edge Switch 2/32 c. Type the administrator password again in the Confirm New Password field, as shown in Figure 2–47. Figure 2–47: User Rights page 3. For the Operator set of data fields: a. Type the operator user name (as specified by the customer’s network administrator) in the New User Name field. Use 16 alphanumeric characters or less. b. Type the operator password (as specified by the customer’s network administrator) in the New Password field.
Installing and Configuring the Edge Switch 2/32 Task 16: Cable Fibre Channel Ports Perform this task to connect devices to the switch. To cable Fibre Channel ports: 1. Route singlemode or multimode fiber-optic cables (depending on the type of SFP pluggable optic transceivers installed) from customer-specified devices to ports at the front of the switch. 2. Connect device cables to small form factor pluggable (SFP) transceivers. Start with port 0 and continue sequentially to the left through port 31. 3.
Installing and Configuring the Edge Switch 2/32 5. Connect the switch-attached fiber-optic cable to the port SFP transceiver. 6. If the switch is managed by an attached HAFM server, go to step 7. If the switch is managed by the Embedded Web Server interface: a. Choose View at the left side of the window. The View window opens with the Switch tab selected and displayed. b. At the View window, click the Port Properties tab.
Installing and Configuring the Edge Switch 2/32 9. Ensure the Link Incident field displays None and the Reason field is blank. If an ISL segmentation or other problem is indicated, refer to the hp StorageWorks edge switch 2/32 service manual to isolate the problem. If no problems are indicated, installation tasks are complete. Task 18: Unpack, Inspect, and Install the Ethernet Hub (Optional) The HAFM server and one or more switches connect through an Ethernet hub installed on a 10/100 Mbps LAN segment.
3 Flexport Upgrade Instructions This chapter provides instructions for upgrading the edge switch 2/32 from 16 ports to 24 ports and from 24 ports to 32 ports by installing the Edge Switch 2/32 flexport upgrade kit, see Table 1–1 on page 1–11. Each port expansion kit includes eight optical transceivers, upgrade instructions, and a entitlement certificate containing transaction code for obtaining a software licence key (feature key) through an HP website.
Flexport Upgrade Instructions Upgrading to 24 Ports Ports 0 through 15 should already be populated (see Figure 3–1, 3). 1. Insert 8 new optical transceivers into ports 16 through 23 (see Figure 3–1, 2) as follows: a. To install a new SFP transceiver, position one of the SFP transceivers so that the key is oriented correctly to the port, and insert the transceiver into the port until it is firmly seated and the latching mechanism clicks.
Flexport Upgrade Instructions Upgrading to 32 Ports Ports 0 through 23 should already be populated (see Figure 3–1, 2 and 3). 1. Insert 8 new optical transceivers into ports 24 through 31 (see Figure 3–1, 1). a. To install a new SFP transceiver, position one of the SFP transceivers so that the key is oriented correctly to the port, and insert the transceiver into the port until it is firmly seated and the latching mechanism clicks.
Flexport Upgrade Instructions 2. Choose Features from the Configure menu on the menu bar. The Configure Feature Key dialog box displays, as shown in Figure 3–2. Figure 3–2: Configure Feature Key dialog box 3. Click New to add a new feature key. The New Feature Key dialog box displays, as shown in Figure 3–3. Figure 3–3: New Feature Key dialog box 4. In the New Feature Key dialog box, enter the switch’s feature key and click OK. The Enable Feature Key dialog box displays, as shown in Figure 3–4.
Flexport Upgrade Instructions The Enable Feature Key dialog box displays with a warning, stating that this action will override the current set of features on the switch. If features are enabled on the switch, they will be listed in the left column.The list on the right is a set of features that come with the new feature key. All of the features that are currently active on the switch are included in the new feature list. 5. Click Activate to activate the new feature key.
A Regulatory Compliance Notices This appendix covers the following topics: • Regulatory Compliance ID Numbers, page A–1 • Federal Communications Commission Notice, page A–2 • Canadian Notice (Avis Canadien), page A–4 • European Union Notice, page A–4 • Japanese Notice, page A–5 • Taiwanese Notice, page A–5 • Laser Safety, page A–6 • Declaration of Conformity, page A–9 Regulatory Compliance ID Numbers For the purpose of regulatory compliance certifications and identification, your HP StorageW
Regulatory Compliance Notices Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
Regulatory Compliance Notices • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. Declaration of Conformity for Products Marked with FCC Logo—United States Only This device complies with Part 15 of the FCC Rules.
Regulatory Compliance Notices IEC EMC Statement (Worldwide) This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
Regulatory Compliance Notices • EN55024 1998 (IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6, IEC61000-4-8, IEC61000-4-11)-Electromagnetic Immunity • EN60950 (IEC60950)-Product Safety • Power Quality: (IEC610000-3-2)-Harmonics and (IEC61000-3-3)-Voltage Fluctuations and Flicker • Also approved under UL 1950, 3rd Edition/CSA C22.2 No.
Regulatory Compliance Notices Harmonics Conformance (Japan) German Noise Declaration Schalldruckpegel Lp = 66.8 dB(A) Am Arbeitsplatz (operator position) Normaler Betrieb (normal operation) Nach ISO 7779:1988 / EN 27779:1991 (Typprüfung) Laser Safety WARNING: To reduce the risk of exposure to hazardous radiation: • Do not try to open the laser device enclosure. There are no user-serviceable components inside.
Regulatory Compliance Notices Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. VARNING ! Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1. Fibre Channel -kytkinlaitteessa ei ole käyttäjän tehtäväksi tarkoitettuja huolto- tai säätötoimenpiteitä.
The OLM includes the following certifications: • UL Recognized Component (USA) • CSA Certified Component (Canada) • TUV Certified Component (European Union) • CB Certificate (Worldwide) The following figure shows the Class 1 information label that appears on the metal cover of the OLM housing.
Regulatory Compliance Notices Declaration of Conformity The Declaration of Conformity is shown on the next page.
B Technical Specifications This appendix contains the following information: • Factory Defaults, page B–1 • Physical Dimensions, page B–3 • Environmental Specifications, page B–4 • Power Requirements, page B–4 • Operating Tolerances, page B–4 • Laser Information, page B–5 Factory Defaults Table B–1 lists the defaults for the passwords, and IP, subnet, and gateway addresses. Table B–1: Factory-Set Defaults Item Customer password Maintenance password Default password level-2 IP address 10.1.1.
Technical Specifications Table B–2: Switch Factory-Default Values for Reset Configuration Option Configuration Identification Default Switch Name NULL string Switch Description “Fibre Channel Switch” Switch Contact “End User Contact (please configure)” Switch Location “End User Contact (please configure)” Port Names NULL strings Port Blocked States Unblocked Extended Distance (10-100km) Disabled LIN Alerts Disabled Port Address Port number plus 4 Ports enabled 16 IP Address 10.1.1.
Technical Specifications Table B–2: Switch Factory-Default Values for Reset Configuration Option (Continued) Configuration SNMP Description Default SNMP Communities “public” — 5 NULL strings SNMP Write Authorizations Read only per community Trap Recipient IP Addressees 0 for each UDP Port 162 SNMP Authorization Trap State 5 Management Server Active Equal Saved State Disabled Remote Offline Control State Disabled Zoning Number of Zone Members 0 Number of Zones 0 Number of Zone Sets 0
Environmental Specifications Figure B–4 lists environmental ranges for shipping, storing, and operating the hp StorageWorks edge switch 2/32. Table B–4: Environmental Specifications Specification Weight Temperature Shipping 17.2 kg (38 lb) Storage 15.4 kg (34 lb) Operating 15.
Technical Specifications Table B–6: Operating Tolerances (Continued) Specification Value Shock and vibration tolerance 60 Gs for 10 milliseconds without nonrecoverable errors Acoustical noise 6.6 Bels Inclination 10° maximum Laser Information Three configurations of cards with fixed optics will be provided for each of the connector types: four extended long-wave ports, four long-wave ports, and four short-wave ports.
Glossary This glossary defines terms used in this guide or in other guides in this series, and is not a comprehensive glossary of computer terms. The following cross-references are used in this glossary: Contrast with. This refers to a term that has an opposite or substantively different meaning. See. This refers the reader to another keyword or phrase for the same term. See also. This refers the reader to additional information contained in another entry.
Glossary backplane The backplane provides 48 VDC power distribution and connections for all logic cards. backup FRU When an active FRU fails, an identical backup FRU takes over operation automatically (failover) to maintain director and Fibre Channel link operation. beaconing Use of light-emitting diodes on ports, port cards, field-replaceable units, and directors to aid in the fault-isolation process; when enabled, active beaconing will cause LEDs to flash for selected components.
Glossary call-home Product feature which enables the HAFM server to automatically contact a support center and report system problems. The support center server accepts calls from the HAFM server, logs reported events, and can notify one or more support center representatives. channel Point-to-point link that transports data from one point to the other.
Glossary configuration data Configuration data includes: identification data, port configuration data, operating parameters, SNMP configuration, and zoning configuration. A configuration backup file is required to restore configuration data if the CTP2 card in a non-redundant director is removed and replaced. connectionless Non-dedicated link. Typically used to describe a link between nodes which allows the switch to forward Class 2 or Class 3 frames as resources (ports) allow.
Glossary default Pertaining to an attribute, value, or option that is assumed when none is explicitly specified. default zone Contains all attached devices that are not members of a separate zone. destination address Address identifier that indicates the targeted destination of a data frame. device Product, connected to a managed director, that is not controlled directly by the Product Manager. See also node.
Glossary E_D_TOV See error-detect time-out value. Embedded Web Server Administrators or operators with a browser-capable PC and an Internet connection can monitor and manage the director through an Embedded Web Server interface. The interface provides a GUI similar to the Product Manager application, and supports director configuration, statistics monitoring, and basic operation.
Glossary fabric element Any active director or node in a switched fabric. fabric port Physical interface within the fabric that connects to an N_Port through a point-to-point full duplex connection. failover Automatic and non-disruptive transition of functions from an active FRU that has failed to a backup FRU. FCC-IOC See Fibre Channel I/O controller. FE-MIB See Fibre Channel fabric element.
Glossary FPM See fiber port module card. F_Port See fabric port. FRU See field-replaceable unit. gateway A multi-homed host used to route network traffic from one network to another, and to pass network traffic from one protocol to another. gateway address A unique string of numbers (in the format xxx.xxx.xxx.xxx) that identifies a gateway on the network. generic port Also known as G_Port.
Glossary homogeneous fabric A fabric consisting of only HP products. hop count The number of hops a unit of information traverses in a fabric. host bus adapter Logic card that provides a link between the server and storage subsystem, and that integrates the operating systems and I/O protocols to ensure interoperability. hot-swapping Removing and replacing a device’s components while the device continues to operate normally.
Glossary interswitch link Also known as ISL. Physical E_Port connection between two directors in a fabric. I/O configuration See input/output configuration. IOCDS A data set that contains an I/O configuration definition built by the IOCP. IOCP See input/output configuration program. IP address See internet protocol address. IPL See initial program load. ISL See interswitch link.
Glossary logical unit number Also known as LUN. In Fibre Channel addressing, a logical unit number is a number assigned to a storage device which, in combination with the storage device’s node port’s world wide name, represents a unique identifier for a logical device on a storage area network. loopback plug In a fiber optic environment, a type of duplex connector used to wrap the optical output signal of a device directly to the optical input.
Glossary multi-switch fabric Fibre Channel fabric created by linking more than one director or fabric switching device within a fabric. name server Program that translates names from one form into another. Domain name servers (DNS) translate domain names into IP addresses. name server zoning N_Port access management that allows N_Ports to communicate if and only if they belong to a common name server zone. network address Name or address that identifies a managed product on a TCP/IP network.
Glossary Offline—when the director is set offline, all ports are set offline. The director transmits the offline sequence (OLS) to attached devices, and the devices cannot log in to the director. operating state (port) Valid states include Online, Offline, Testing, Beaconing, Invalid Attachment, Link Incident, No Light, Not Operational, Port Failure, Segmented E_Port.
Glossary persistent binding A form of server-level access control that uses configuration information to bind a server to a specific Fibre Channel storage volume (or logical device) using a unit number. port Receptacle on a device to which a cable leading to another device can be attached. port card Field-replaceable hardware component that provides the port connections for fiber cables and performs specific device-dependent logic functions.
Glossary remote access link Connection to a device or program on a computer network via a (geographically) remote workstation. remote notification A process by which a system is able to inform remote users and/or workstations of certain classes of events that occur on the system. E-mail notification and the configuration of SNMP trap recipients are two examples of remote notification programs that can be implemented on director-class switches.
Glossary SNMP community Also known as SNMP community string. SNMP community is a cluster of managed products (in SNMP terminology, hosts) to which the server or managed product running the SNMP agent belongs. SNMP community name The name assigned to a given SNMP community. Queries from an SNMP management station to a device running an SNMP agent will only elicit a response if those queries are addressed with the correct SNMP community name. SSP See system services processor.
Glossary unblocked port Devices attached to an unblocked port can login to the director and communicate with devices attached to any other unblocked port assuming that this is supported by the current zoning configuration. unicast Communication between a single sender and a single receiver over a network. Compare to multicast and anycast (communication between any sender and the nearest of a group of receivers).
Glossary zone member Specification of a device to be included in a zone. A zone member can be identified by the port number of the director to which it is attached or by its world wide name. In multi-switch fabrics, identification of end-devices/nodes by world wide name is preferable. zone set See zone. zoning Grouping of several devices by function or by location. All devices connected to a connectivity product, such as the director, may be configured into one or more zones. See also zone.
Index 10/100 Mbps LAN connectors 1–11 A active zone set state, default value B–3 additional port function configuring 2–16 reset by configuration reset 2–6 addresses, director default values B–2 alerts, introduction 1–3 audience ix B BB_Credit default value B–2 bb_credit 2–30 beaconing, introduction 1–3 binding, port 2–35 buffer-to-buffer credit default value B–2 C cables, FCC compliance statement A–3 call-home feature introduction 1–3 overview 2–42 Canadian Notice (Avis Canadien) A–4 CE marking A–4 Comp
Index domain RSCNs 2–28 E E_D_TOV default value B–2 e_d_tov 2–31 fabric segmentation 2–31 less than r_a_tov 2–31 multiswitch fabrics 2–31 rerouting delay 2–28 E_port segmentation preferred domain ID 2–27 e-mail notification configuring, product manager 2–40 introduction 1–3 embedded web server.
Index Installation Options 2–3 Installation Task Summary (table) 2–1 installation tasks backing-up configuration data 2–51 cabling Fibre Channel ports 2–69 configuring network addresses 2–6 product manager application 2–23 switch from EWS 2–51 switch to the HAFM Application 2–13 configuring OSMS or FICON management server 2–19 configuring the feature key 2–15 connecting switch to fabric director 2–69 LAN-connecting the switch 2–11 recording and verifying HAFM Server restoration information 2–13 setting swi
Index port binding 2–35 port blocked states, default value B–2 port, cabling 2–69 ports binding 2–35 default values B–2 UDP, default value B–3 power supplies 1–7 LEDs 1–9 power supply requirements B–4 preferred domain ID 2–27 multiswitch fabric 2–26, 2–30 preferred domain ID, default value B–2 principal switch, determining 2–31 product manager configuring 2–23 configuring e-mail notification 2–40 configuring SNMP trap message recipients 2–39 configuring switch identification 2–24 R R_A_TOV default value B
Index operating mode 2–28 preferred domain ID 2–27 rerouting delay 2–27 switch priority 2–31 related number codes 2–32 switch priority setting 2–32 switches, principal, determining 2–31 symbols on equipment xi T Task 1, Verify Installation Requirements 2–3 Task 10, Configure Feature Key (Optional) 2–15 Task 11, Configure OSMS or FICON Management Server (Optional) 2–19 Task 12, Set Switch Date and Time 2–21 Task 13, Configure the edge 2/32 product manager application 2–23 Task 14, Test Remote Notification
