Installation guide

TABLE 11–1 Single Processor Systems (continued)
Zenith Data Systems Z-Station GT Pro (PP-200 IDE)
Zenith Data Systems Z-Station GT Pro-S (PP-200 SCSI)
Zenith Data Systems Z-Station LX Pro-S (PP-180 SCSI)
Zenith Data Systems Z-Station LX Pro (PP-200)
Zenith Data Systems Z-Station LX Pro-S (PP-200 SCSI)
Zenith Data Systems Z-Station VP (486DX4/100)
Zenith Data Systems Z-Station VP (P-90)
Zenith Data Systems Z-Station VP (P-100)
Zenith Data Systems Z-Station VP (P-120)
Zenith Data Systems Z-Station VP (P-133)
1. Requires substituting the video card with one supported by Solaris Intel Platform Edition.
2. Requires substituting the network card with one supported by Solaris Intel Platform Edition.
3. Must use a CD-ROM drive supported by Solaris Intel Platform Edition.
4. This model is an MP server but has only been tested with one CPU.
5. Additional configuration is required to install the Solaris 2.6 software on this system; refer to the notes on
“Memory Mapping Problems” in Release Notes for Solaris 2.6 (Intel Platform Edition) for information.
6. Server System. Integrated video currently only works in 640x480 VGA mode.
7. Requires non-default BIOS settings for proper operation.
8. The three-disk CD-ROM changer is not supported at this time.
9. Select “Trident 9000” when configuring the display adapter, and be sure to upgrade the video RAM on the
motherboard.
10. System must be upgraded to a minimum of 1-Mbyte video memory and a minimum of 32-Mbytes system
memory.
11. Some versions may require a future Driver Update to support integrated video due to a manufacturer’s part
change.
12. PC Card support is planned for a future Driver Update.
13. The design of the Cache controller requires that you map out the memory range used by the SCSI controller, or
the system will not work; the on-board hardware watchdog circuit R39 must also be disabled.
14. Warning: FLASH BIOS must be write-protected before attempting to install the Solaris software; remove jumper
JP9 on the motherboard and use BIOS revision -10 or later.
15. Only tested with vendor’s ATI Mach32 video option.
16. Integrated audio chip is not currently supported.
17. Must set the Adaptec SCSI BIOS to address CC000.
18. This series of machines comes in various models and configurations. If the FCC ID label on the back panel of
your machine contains one of the three-digit codes 430, 450, 470, 520, or 550, then it is based on a platform that
was tested for compatibility and should run Solaris 2.6 Intel Platform Edition. However, ensure that other
optional equipment and subsystems on your specific model are listed in this document.
19. The newer version of this system had BIOS compatibility issues at the time of test. Also, attach the CD-ROM to
the primary IDE channel.
20. Built-in ATI video card currently only supported in 43-Hz mode.
21. For Solaris compatibility, specify an STB S3 Trio video system by requesting option DE-15-200-2-SFC12-E16/
1-DU-3P4I-U at time of order.
22. For Solaris compatibility, specify an STB S3 Trio video system by requesting option DS-16-200-1.2-IFC8-E32/
1S-DF-4P4I-U at time of order.
23. For Solaris compatibility, specify an STB S3 Trio video system by requesting option DS-16-200-2-SFC8-E32/
1S-DF-4P4I-U at time of order.
24. For Solaris compatibility, specify an STB S3 Trio video system by requesting option DT-15-133-1.2-IFC8-E16/
1S-CU-2P2I-U at time of order.
Hardware Compatibility List for Solaris 2.6 (Intel Platform Edition) 11-29