User`s manual

ManualsBrandsCompeGPS ManualsGPSTwoNav

CompeGPS Team S.L.

http://www.compegps.com

http://support.compegps.com

TwoNav Sportiva 2.1

User‟s Manual

Content

Content .......................................................................................................................................... 1

1 Introduction............................................................................................................................. 5

2 Maintenance ........................................................................................................................... 6

2.1 Battery Recharge........................................................................................................... 6

2.2 Bumps and water........................................................................................................... 6

2.3 Autonomy ...................................................................................................................... 7

2.4 Connection to PC (storage unit) .................................................................................... 7

2.5 Using the electronic compass ....................................................................................... 7

2.6 Updating the software ................................................................................................... 7

3 General description ................................................................................................................ 8

3.1 The device ..................................................................................................................... 8

3.2 Navigation window......................................................................................................... 8

3.3 Menu ............................................................................................................................ 12

3.3.1 On-road/Off-road ..................................................................................................... 13

3.3.2 Navigate… ............................................................................................................... 13

3.3.3 Data Lists ................................................................................................................. 13

3.3.4 Discover ................................................................................................................... 14

3.3.5 Status....................................................................................................................... 15

3.3.6 Settings .................................................................................................................... 16

3.4 Contextual menus........................................................................................................ 16

3.5 Shifting over lists ......................................................................................................... 17

3.6 Using MicroSD slot ...................................................................................................... 18

4 Settings ................................................................................................................................ 18

4.1 On-road/Off-road Selector ........................................................................................... 18

4.2 2D/3D/3D+ ................................................................................................................... 20

4.3 Data fields .................................................................................................................... 21

4.3.1 Selection of the data fields ...................................................................................... 23

Summary of content (95 pages)

PAGE 1
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com TwoNav Sportiva 2.1 User‟s Manual Content Content .......................................................................................................................................... 1 1 Introduction............................................................................................................................. 5 2 Maintenance ..........................................................................................
PAGE 2
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.3.2 Special Functions .................................................................................................... 23 4.4 Record the track .......................................................................................................... 24 4.5 Favourites .................................................................................................................... 24 4.6 Display ...........................
PAGE 3
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 5 6 4.9.4 Language ................................................................................................................. 43 4.9.5 Calibrate screen ...................................................................................................... 43 4.9.6 Barometer calibration .............................................................................................. 43 4.9.7 Compass calibration ..............
PAGE 4
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.1.9 8.2 Waypoints contextual menus .................................................................................. 59 Routes ......................................................................................................................... 60 8.2.1 What is a route? ...................................................................................................... 60 8.2.2 Supported formats ...........................
PAGE 5
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 9.2 Zoom to… .................................................................................................................... 90 10 Support ............................................................................................................................ 91 11 Limited warranty ..............................................................................................................
PAGE 6
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com very important to be alert to these changes and to adapt to the new situation. As soon as the program detects that it has not been able to follow the preset route, it will calculate a new one, which will take you to your destination just the same.  TwoNav assists you in navigation. Traffic regulations have always preference! 2 Maintenance 2.1 Battery Recharge The TwoNav Sportiva Li-on battery is recharged via the USB port.
PAGE 7
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 2.3 Autonomy TwoNav Sportiva may operate around 6 consecutive hours with the screen ON with no need of recharging the battery and up to 20 hours with the screen OFF and recording the track. The screen uses an important part of the energy resources, so turning it off may make the life of the device longer. The screen of the device will be turned off by default after 1 minute of inactivity.
PAGE 8
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Normally, software updates are for TwoNav, but operating system can also have updates. Visit regularly the TwoNav (www.twonav.com) and CompeGPS (www.compegps.com) web pages to be regularly informed about the latest available version for your device and get to know the steps to follow for installing it. 3 General description 3.
PAGE 9
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 1. Distance to next event: Distance left to next event (roundabout, waypoint, exit). 2. Next manoeuvre: When navigating On-road, the „next event‟ space will display a representation of the next manoeuvre to be done (right turn, left turn, roundabout, diversion, etc.). 3. Tool Bar: Its content can be customized from Tool bar manager 4. Show/Hide tools 5. Mute 6.
PAGE 10
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 11. Time: It is refreshed with the data received from the GPS 12. Speed 13. Distance to Destination 14. Estimated time of arrival to destination 15. Menu button: Goes to TwoNav Main menu. 16. Status icons (enters status window): To indicate the present battery and GPS coverage level. The page „Status‟ is entered by pressing on them. 17. Speed limit of present road: Indicates the legal speed limit of the road on which we are. 18.
PAGE 11
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 28. Compass: Shows the orientation of the device. The source of this datum (GPS, electronic compass or „automatic‟) may be set from „menu > Settings > Off-road > Bearing‟. 29. Currently Recorded Track: If the present track is being recorded, we can see its trace marks behind us. 30. Guide line (waypoint direction/track): Joins your present position to the place you are heading for (track or next waypoint) 31. Next waypoint 32.
PAGE 12
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com b. Rotation: it changes the orientation of the map in a clock-wise or anti clock-wise sense (horizontal dragging) or up/down (vertical dragging). You may move the map dragging it by means of the touch screen or the joystick. 37. Altitude 38. Show/hide graph/data bar: You may hide the data bar to get a broader view of the map.
PAGE 13
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 3.3.1 On-road/Off-road TwoNav features two navigation modes to meet the needs of any environment. Press the corresponding tab on the main menu to activate the most suitable mode for you. For further information, check the section On-road/Off-road selector 3.3.
PAGE 14
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Available elements open: The available elements on the data folder can be seen on this list. The open elements will be arranged on the top of the list with a ticked square. o Press on the name of any element to open it. o Press on the left square to close it.  Sub-elements: By briefly clicking on the name of an element (waypoints file or route) the waypoints which it contains will be displayed.
PAGE 15
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Stop simulation: It stops the ongoing simulation (both from A-B spots as from any track being animated).  3D Panorama: By using this option you may get an aerial view of the surroundings. In order to do it, 3D mode must be activated. 3.3.
PAGE 16
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com GPS possible states: Disconnected Connecting... Error (not found) Connected without position Connected and with position Simulating Battery: you will be able to see the percentage of load in the battery and, by clicking on it, you may manage the autonomy options of the device. (+info) Brightness: percentage of luminosity displayed by the screen. (+info).
PAGE 17
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com To open the Contextual Menu of any element (track, map, waypoint…), press on it for one second. You may open contextual menus on the following settings of the user interface:  Navigation window (map): Depending on the element on which you open the Contextual, you may enter different functions. There is a description of the available functions on the menu of each element on the specific sections for waypoints, routes, tracks or maps.
PAGE 18
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com If you want to move along the lists in a more accurate way, you may use the side arrows to achieve a more controlled movement. 3.6 Using MicroSD slot TwoNav Sportiva allows to extend storage memory with a MicroSD card.
PAGE 19
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com program also change in various aspects, which are generally explained in this section and are detailed in other sections of this manual.
PAGE 20
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.2 2D/3D/3D+ TwoNav offers three visualizing modes so you have the most adequate perspective in each moment.  2D: Zenith Plan.  3D: Three dimensional flat image, i.e. with no relief, but with a perspective.  3D+: Displays the holography of the terrain in real 3D.
PAGE 21
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.3 Data fields TwoNav contains a multitude of data on your navigation that may be of great interest in your outings (speed, height, distances...). This data is basically found in two spaces: 1. Data bar: The data bar will be displayed at the bottom of the screen during navigation. You will be able to keep it visible or hide it by means of the icon.
PAGE 22
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 3. Graph page: It contains a special field with an altitude profile. If you are navigating a route or a track, it will be shown with current position marked by a vertical red line. You can zoom using buttons at top right. If not navigating a route or a track, currently recorded track will be shown. 4 data fields related with altitude accompany the graph.
PAGE 23
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Data fields are configurable to have a different set for On-Road or Off-Road. Changes made in one mode will not affect the other. 4.3.1 Selection of the data fields You can select data fields in two ways:   Change just one field: By opening the contextual menu in any field (long click) and selecting „Change this field‟. This will let you choose directly the data to display in that field.
PAGE 24
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 5. Reset all: Resets all data fields that can be reset except total odometer 1 and 2. 6. Countdown: You may define the value from which units of distance and time will keep being subtracted (according to field) until reaching 0. 7. Compass calibration: Direct access to the digital compass calibration. 8. Barometer calibration: Direct access to the digital barometer calibration. 4.
PAGE 25
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Press on the „stylus‟ icon to edit this list On the following screen, the „add‟ icon lets you create your first Favourite point Choose the way you want to create your Favourite point:  Present position: it will establish your current position as a favourite point, and will ask you directly to add a name or establish it as your home.  Present destination: it will establish the present destination of the active navigation.
PAGE 26
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.6 Display 4.6.1 Available commands Default/Advanced Default:       Automaps Orientate map Autozoom Night view Re-centring Rotate screen Advanced:          4.6.
PAGE 27
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com It is recommended to have the Automaps option always on, and more especially on those instances in which you need to make a change in navigation mode during the route.
PAGE 28
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com You may modify this option from the button bar on the navigation window or from the „display‟ menu. 4.6.4 Auto zoom “Main menu > Settings > Display > Auto zoom” If the Auto zoom mode is active, the program will calculate the most suitable zoom for the present speed. Generally, the higher the speed, the further it will go.
PAGE 29
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com The option „At night‟ makes it automatic but only for night and not for tunnels. If „automatic‟ is off, you will be able to select manually if you wish to have the night mode on or not. Note: TwoNav always keeps the time updated as long as the device receives the GPS signal. Usually, inside buildings, there is no reception of satellite signals and so, automatic „Night View‟ may be affected. 4.6.
PAGE 30
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com The data bar manages the elements displayed at the bottom of the page during navigation. 3. You may delete data by pressing on the left „check‟ mark and add other data by pressing on them. See a list of these variables and their meaning in Appendix 1. 4. On the compass and graph pages, a squared icon on the side shows the place corresponding to the enhanced field (normally compass and track graph) that will be enlarged on the screen.
PAGE 31
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com will be shown, alphabetically ordered. If 'infinite' button is pressed, full list of data fields will be shown. You can also add or remove pages to de default ones using the + or - symbols at top right of the data field manager window. Just press - to remove currently selected data page. Follow next steps to add a new page: 1. Press „+‟ 2. Enter a name for new page 3. Select a template for new data page 4. Choose data fields for it.
PAGE 32
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.6.8 Tool bar „Main Menu > Settings > Display > Tool bar‟ Tool bar can be customized to show the better combination for user. Tool bar manager works in the same way as data field manager. Next functions can be added to the tool bar:               Page: Access data pages 3D mode: Switch 2D-3D/3D+ Orient map: Track up / North up Pan/Rotate: Movement mode Open...
PAGE 33
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.6.9 3D Reliefs „Main menu > Settings > Off-road > 3D Reliefs‟ TwoNav may use elevation maps (point meshes with information on the height of the ground) to have the altitude data on the references created with the program (e.g. tracks, waypoints, etc.) to habilitate the visualizing mode 3D+ (3D real).
PAGE 34
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com By means of the active POIs list you will be able to choose the POIs categories that the map is to show. All the POIs will be shown by default, but if the vision of certain categories is useless for you or even interferes, you may take them off so the map does not show them. When selecting destination or „zoom to‟ you will have all the information of the POIs categories, even those not being shown on the map. 4.6.
PAGE 35
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Draw the parallel bow lines: we may choose to display or not the parallel lines of the first option.  Variable ring: you may add more rings around your position. You have to define the radium of the inner ring and the number of successive rings which will be equidistant from the first inner ring.  See turning radium: when turning, the radium corresponding to the circumference described will be displayed.
PAGE 36
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.8 4.8.1 4.8.1.1 Navigation Available commands Onroad/Offroad and Default/Advanced On-Road Default:      Autoroute Speed limit Ecocalculator Smoother Tracklog Advanced:     4.8.1.2 WPT Alert Next WPT Altitude Bearing Off-Road Default:    Tracklog WPT Alert Next WPT Advanced:   4.8.
PAGE 37
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Fast/Short: The first option will calculate the estimated time of arrival, bearing in mind the speed of each road and will suggest the navigation which takes shorter. The second option will suggest a navigation based on distance, choosing the shortest way, although it may not be the fastest. When the option „by time‟ is activated, a chronometer will be displayed as a key icon.
PAGE 38
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.8.3 Speed limit “Main Menu > Settings > Navigation > Speed limit” This section gives you options related to the speed alerts and traffic radars and can be set according to your preferences:  Set a speed limit: the speed limit of each particular road will be considered by default, but you can set a fixed speed limit disregards the limit of each road.
PAGE 39
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com While navigating, TwoNav may automatically record the track of your departure and save it in the TwoNavData folder. Set up according to your needs or preferences:  Recording interval: Choose the type of recording and interval you wish for the track to be generated for your navigation. o By time: The point of each track will be recorder every X seconds. o By distance: The point of each track will be recorder every X meters.
PAGE 40
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Only buttons bar: Never will automatically change to next waypoint, only manually with 'NextWPT' and 'PreviousWPT' buttons at buttons bar. Also from this options section, a default radius can be assigned for route waypoints, which will be taken when this information is not available. It means, if we defined a radius for a concrete waypoint of the route, it will be respected.
PAGE 41
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com o Automatic calibration tool: If you select the „Automatic‟ option in the „altitude‟ selector menu, TwoNav will continuously calibrate the barometric altimeter using the GPS position along time (see following point). If after some time you select „Barometric altimeter‟, the introduced calibration will be saved with the „automatic‟ option, but it won‟t be updated with the new GPS measurements.
PAGE 42
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Voice: Regulate the volume of the alert voices for the next manoeuvre.  Alarm: Regulate the volume of the alarms and radar warnings, speed limits and arrival at waypoints.  Clicks: Regulate the volume of pulses on the touch screen or buttons. 4.9.2 Brightness ‟ from „Main Menu > Settings > System > Brightness‟ Regulate the amount of light you wish the screen to have and adjust it to each situation.
PAGE 43
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.9.4 Language “Main Menu > Settings > System > Language”. You may modify the language of the texts and voices of the system from this section. Note: The conversion of the voices may take more than one minute. 4.9.
PAGE 44
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Calibration is a necessary procedure for the directions supplied by the electronic compass to be correct. It is an instrument very sensitive to weather and magnetic fields changes, so it has to be recalibrated each time it is going to be used in a new area. Calibration must be carried out in the open air and far from sources of alterations of the magnetic fields, such as cars, buildings or electric lines.
PAGE 45
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4.9.9 Units „Main Menu > Settings > System > Units‟ You may determine which type of measurement unit to use in TwoNav:  Distances: in kilometres, miles, nautical miles, metres or feet.  Altitudes in: metres or feet.  Speed in: kilometres/hour, miles/hour, nautical miles or minutes/kilometre.  Short distances in: kilometres/hour, miles, nautical miles, metres or feet.
PAGE 46
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Besides, from this option, you may configure the order in which the degrees will be displayed. By default, TwoNav Works with Lat / Long and Datum WGS84 Coordinates. 4.9.11 Time zone „Main menu > Settings > System > Time zone‟ TwoNav lets you choose the time it is according to the Universal Time Coordinates (UTC) that will appear by default with the time-zone corresponding to the Central European Time (CET).
PAGE 47
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com       Reload data when restarting: Load same data which was loaded when closed application last time. Draw map corners: Show frames of available maps on navigation window. Draw arrows over the track: To easily know its direction. Resume navigation at start: Propose same destination which was set when closed application last time.
PAGE 48
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com o Gas station: Creates a list of gasoline stations available near from current position.  Favourites: You may create your own list of favourite places to be able to enter them quickly. To manage this list, press the „edit‟ button. (+info)  History: The recently selected destinations are stored here.  By map: Select the exact spot and press OK.  Waypoint: Select a waypoint among the ones loaded or created.
PAGE 49
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 6 Following indications Once the destination is selected, TwoNav will assist you in reaching it.
PAGE 50
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com On Road : Door to door navigation on the CompeGPS V-maps cartographic basis, enjoying the characteristic assistance type of the urban navigators. The route will be automatically calculated through the streets and along the itinerary accurate visual and aural indications will be given on the manoeuvres to carry out. Important: On-road mode will only be available if you have a routable V-map present in maps folder.
PAGE 51
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 6.1 On-road Navigation The information offered by this navigation mode is more than in Off-road mode, as all the information contained in the V-maps cartographic data base is used to show accurate indications of the next manoeuvres. Besides, audible signals are given in order not to get distracted from the traffic. Important: On-road mode will only be available if you have a routable V-map present in maps folder.
PAGE 52
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8. Present Street: Name of the street where you are. When pressing on an element of the map (for instance a Chemist‟s) a yellow square will appear indicating the name of this element plus some other interesting information. This way, you may also check the names of the streets in the area. See the On screen section for complete information on the elements present on the navigation screen. 6.
PAGE 53
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com See the Waypoints, Routes and Tracks section for further information on these elements. 6.2.1 Visual information 1. GOTO arrow: Direction on which the next waypoint is. When following a track, it will indicate its direction (see Off-road navigation). 2. Track name / Next Waypoint: Name of the next waypoint or the track being followed. 3. Loaded route 4. Loaded Track 5. Next waypoint 6.
PAGE 54
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8. Compass: Shows the orientation of the device. The source of this datum may be set (GPS, electronic compass or „automatic‟) from „menu > Settings > Off-road > Bearing‟. 7 Radar warnings / POIs During your navigation, TwoNav may alert you when you get close to certain points of special interest. 7.1.1 Radars One special case of these types of points is the radars that control traffic speed.
PAGE 55
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com The waypoints are kept inside waypoints files (usually in .WPT format), so a waypoint folder may contain just one or more waypoints. They are represented on screen as points to which a name or an icon may be applied. refuge 8.1.2 Supported formats TwoNav can open directly next waypoint formats:     *.WPT *.BWPT *.LOC *.GPX More waypoint formats can be imported and converted to these ones from CompeGPS Land/Air. 8.1.
PAGE 56
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Enter the properties of the waypoint window  Create a new waypoint within the waypoints file in which the selected waypoint is.  Zoom here  Navigate By a long click on any open Waypoints file or on a specific Waypoint, you will enter the Contextual Menu with all the available functions for this element. 8.1.4 8.1.4.
PAGE 57
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com If there are no waypoints files loaded, TwoNav will create one with a default name (new WPT), which you will be able to modify o the waypoints list. These functions can be added to tool bar by means of the tool manager. „Mark and edit WPT‟ can be also accessed from „Main menu > Data > Mark and edit WPT‟ 8.1.5.1.
PAGE 58
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.1.5.3.2 Save waypoints as If you wish to save the waypoints file by another name, location (folder) or format (*.WPT or *.GPX), you may select the option Save WPT As from the contextual menu of the waypoints in the waypoints list. 8.1.6 Search loaded waypoint on screen To centre the screen on a waypoint: 1. Enter Main Menu by pressing 2. Select „Main Menu > Data > Waypoints > Waypoints list‟ 3.
PAGE 59
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.
PAGE 60
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Navigate… (+ info) 3. Contextual menu of a concrete waypoint on the map:  New…  Waypoint here (+ info)  Begin a route here (+ info)  Begin track here (+ info)  Properties (+ info)  Save Waypoints (+ info)  Close Waypoints (+ info)  Delete Waypoint (+ info)  Navigate… (+ info) To see the options of the contextual menu of a waypoint within a route go to Routes contextual menus‟. 8.2 8.2.
PAGE 61
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  *.GPX More route formats can be imported and converted to these ones from CompeGPS Land/Air. 8.2.3 List of routes “Main menu > Data > Routes” The routes management is centralized in the routes list, although it is also possible to carry out many actions directly from the navigation screen by means of the contextual menu.
PAGE 62
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com From left to right:  Enter the waypoint properties window  Create a new waypoint within the route in which the selected waypoint is.  Zoom here  Navigate (activate) By a long click on any open route or on any concrete Waypoint within a route, the Contextual Menu with all the available functions for this element will open. 8.2.4 8.2.4.
PAGE 63
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.2.5 Create and edit 8.2.5.1 Create a route 8.2.5.1.1 Create a route on the map The fastest and easiest way of creating a route is from the routes editor in the navigation window, on the map. To obtain a correct route you will need a well calibrated map as a reference.
PAGE 64
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com While editing, you may move the map by dragging it for adding waypoints in other spots in the map. The dragging movement won‟t add waypoints it will only shift the map. To include a waypoint you must click briefly. You may move the position of the created waypoints by selecting and dragging them (+info) 4.
PAGE 65
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 3. Press on the spot in the map where you want to generate the new waypoint. 4. Add as many waypoints as you wish. If you want to add waypoints in other places along the route, all you have to do is repeat step 2 and 3. 5. Once you are satisfied with the route, enter the Contextual Menu of the route (by means of a long click on the screen) and select „Close Edit‟.
PAGE 66
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.2.5.2.2 Delete waypoints of the route You may delete a waypoint from the routes list or directly from the map. To do so, open the contextual menu on it and select „delete waypoint‟. 8.2.5.2.3 Move the position of the waypoints of the route You may modify the position of any waypoint on the map or by introducing its coordinates: 8.2.5.2.3.1 On the map 1.
PAGE 67
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com If after selecting a waypoint you click briefly on the map, a new waypoint will be created just after the selected one. 8.2.5.2.3.2 Introduce coordinates In order to modify the coordinates of a waypoint, all you have to do is enter its properties window and introduce the new value, checking that the datum and the projection are correct. 8.2.5.2.
PAGE 68
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.2.6 Search loaded route on screen To centre the screen on a route: 1. Enter Main Menu by clicking on 2. Select „Main Menu > Data> Routes 3. Click on a concrete waypoint and choose between: a. Press the button. b. Enter the Contextual Menu of the waypoint (long click on the name or „Menu‟ button) and then click on „Zoom here‟. A window will open displaying the waypoint on screen with a possibility of zooming in or out. 4.
PAGE 69
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Through the data fields: You may place the field „route graph‟ in any position in the data pages, although it is recommended to use the space of the graph page to do it. (+info) 8.2.9 Activate a route (navigate) You may activate (navigate) a route in three ways:  Menu “Navigate…”  Contextual Menu of the route within the routes list (long click on the route within the routes list).
PAGE 70
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com Once activated, TwoNav will guide you towards the first waypoint along the route. When you reach a waypoint along the route, you will be guided towards the next one, and so on until the end of the route. If you are in Off-road mode, a straight line will be displayed from your position to the next waypoint.
PAGE 71
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Waypoint here (+ info)  Begin route here (+ info)  Begin track here (+ info)  Properties of the Route (+info)  Save Route (+info)  Close Route (+info)  Edit Route (+info)  Activate (+info) 4.
PAGE 72
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.3 8.3.1 Tracks What is a track? A track is a group of points ordered by time, where each point contains information on the position, time and date, coordinates and, in most cases, altitudes. Tracks can be split into 2 and 3 dimensional ones, depending on whether they have or not the altitudes of the track points. For further information, check Track tools.
PAGE 73
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com *Note: If, in the same day, you have made more than one track, the names will be distinguished by a number at the end that identifies the order in which they were created, (e.g. 2008-12-1501.TRK, 2008-12-15-02.TRK, …). You may rename both the tracks previously saved as the track currently being recorded by using the track properties or save as. 8.3.
PAGE 74
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.3.5 8.3.5.1 Open and close Open track From the tracks list, by clicking on the name of one of the available folders, it will open. You will know it is open because it will be visible at the top of the list and with the left square marked 8.3.5.2 . Close track Press on the left check mark of the open track in order to close it.
PAGE 75
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 2. On this menu, select New > Begin new track here. In this moment, the menu will close and it will go into the tracks edit mode. 3. On the map and with the stylus, start creating the points of the track (by pressing on the places where there should be points): During editing, you may move the map by dragging it in order to add points in other parts of the map. The dragging movement won‟t add points, it will just move the map.
PAGE 76
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4. Once you are satisfied with the track, enter the Contextual Menu of the track (by a long click on the screen) and select Close Edit. See the edit track section to add new points or modify the existing ones. Besides the „manually‟ created tracks, TwoNav will keep creating „automatically‟ the track of your outing recording your position according to the settings of tracklog (+info on the recording of the present track). 8.3.6.2 8.3.6.
PAGE 77
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 5. Once you are satisfied with the track, enter the contextual menu (by means of a long click on the screen) and select Close Edit. When entering the editor, the point of the selected track will be the last one, so if you press on the map, points will be added to the last part of the track. 8.3.6.2.2 Delete points from track 1.
PAGE 78
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 4. To move another point you must select it first (by pressing briefly) and then drag it. 5. Once you are satisfied with the track, enter the contextual menu (by a long click on the screen) and then select Close Edit. If, once selected a point, you click briefly on the map, a new track point will be created right after the selected one. 8.3.6.2.3.
PAGE 79
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 8.3.6.3.2 Operations with legs If you open the contextual menu on a leg of the track in the navigation window from the „legs‟ option, you will be able to enter the following functions:  Leg properties: You may change the colour and thickness of the leg and add a note.  Change leg (+info)  Delete this leg: the points of this leg will be deleted from the track, leaving an empty space in its place.
PAGE 80
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Reduce the number of points (Reduce num. points): By introducing the number of points, the track is drawn with the points keeping the shape of the track in the most possible faithful manner.  Assign time and speed (Assign time/speed): By using this option you may determine a time for departure and a constant speed so TwoNav calculates the estimated time of arrival to each point in the track.
PAGE 81
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com A window displaying the track on screen with the possibility of zooming in or out will open. 4. To exit the window you may choose between:  Press  Press and return to the navigation window keeping the focus you had in the zoom window. 8.3.8 8.3.8.1 and return to the tracks list. Properties Track properties The different data on a loaded track can be consulted (distance, area it encloses, maximum altitude, etc.
PAGE 82
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  General: Name of file (you may also change the track name from the contextual menu of the tracks list or by „save as‟), User name, Outing name, Notes on track.  Date and time: Day, Departure time (first track point), Arrival time (last track point), Duration, Difference between local time and UTC (more or less hours in regards to GMT), Time stopped, Time moving.
PAGE 83
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com From the window that will open, you may enter:  Icon: Choose the icon with which you wish to mark the position on this point of the track  Description: You may include a note of your choice for this place.  Coordinates: You may consult or modify the coordinates of the point.  Day and date  Associations: it associates image or sound files to your waypoints so they are displayed during navigation when reaching this point.
PAGE 84
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  GOTO arrow: In the „next event‟ space, an arrow will be displayed to indicate a direction tangent to the track. It means you can take the direction of this arrow as a reference to keep going your way. Note: If you are over 50 metres far from the track, the GOTO arrow will indicate the perpendicular to the track instead of the tangent.
PAGE 85
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Play (+info)  Zoom here (+info)  Edit the track (+info)  Send to  Tools (+info)  Activate (+info) 2. Contextual menu of a track on the map:   Waypoint here (+ info)  Begin route here (+ info)  Begin track here (+ info)  Track properties (+info)  Save Track (+info)  Close Track (+info)  Edit Track (+info)  Edit Track point (+info)  Activate (+info)  Legs (+info)  8.
PAGE 86
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com      *.ECW (Raster). This format is not compatible with TwoNav Symbian and TwoNav iPhone. *.VMAP/*MPVF (CompeGPS vector map format) *.IMP (calibration file requiring image file) *.MAP (calibration file requiring image file) *.CDEM (3D relief) More map formats can be imported and converted to these ones from CompeGPS Land/Air. 8.4.
PAGE 87
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com If you have selected a map, the buttons at the bottom of the screen will let you enter the most important functionalities this element has: From left to right:  See all/See available ones for present position  Properties  Zoom here  Close 8.4.4 8.4.4.1 Open and close Automaps By activating this position, TwoNav will try to load the best map in each moment.
PAGE 88
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com b. Enter the Contextual Menu of the map (long click on the name or on the „Menu‟ button) and click on „Zoom here‟. A window display in the track on the screen will open with the possibility of zooming in or out. 4. To exit the window you may choose between:  Press  Press and return to the navigation window keeping the focus you had in the zoom window. 8.4.6 and it will return to the tracks list.
PAGE 89
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Multi-map, Advanced...: (+ info). 2. Contextual menu of the map in the maps list:  Properties of the map (+ info)  Close map (+ info)  Zoom here (+ info)  Multi-Maps, Advanced (+ info) 9 “Simulation” and “Zoom to...” 9.1 Simulation TwoNav lets you see a representation of the itinerary you are going to follow. It will be displayed with the position icon in green to distinguish it from the „present position‟ icon in red.
PAGE 90
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com prevailing one, so the position will be centred on it and the movement statistics will be related to it. To stop the simulation, you may go to „Main menu > Discover > Stop sim.‟ 9.2 Zoom to… The option „Zoom to…‟ allows you to carry out a quick pre-visualization of the element you wish to see on the map*.
PAGE 91
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Coordinates: TwoNav allows you to quickly visualize concrete coordinates introduced by you. Remember that to visualize what these coordinates correspond to, you must have loaded a map of that area. *Note: the option „Zoom to‟ shows you the element that you want to see in a window solely for this purpose that is not the same as the navigation window.
PAGE 92
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 2- By the CompeGPS‟ on-line free support service, accessing from http://support.compegps.com web page. Once the contact has been confirmed, next steps to execute your guaranty will be communicated to the client. Any demand must come with its correspondent original receipt, where vendor name and address, date and place of purchase and type of product must be specified. Any shipping costs are the sole responsibility of the customer.
PAGE 93
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Mean speed: Mean speed from start to now  Odometer Total 1: Accumulated distance of all your outings. It is not automatically reset when turning off the device  Partial CO2 emission: CO2 emission from departure. It is reset every time the device is turned off  Partial distance: Counter of distance covered from the beginning of departure.
PAGE 94
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com  Next WPT: Name of the waypoint you are going to  Norm.
PAGE 95
CompeGPS Team S.L. http://www.compegps.com http://support.compegps.com 'N' 'Ñ' „O‟ 'Ó', 'Ò', 'Ö', 'Ô', 'Ø', 'Õ', 'Œ' 'S' 'Š', 'ß' 'T' 'Þ' „U‟ 'Ú', 'Ù', 'Ü', 'Û' „Y‟ 'Ý', 'Ÿ' 'Z' 'Ž' '-', '_', '\' ' ' (space) Therefore, if you have to introduce „LidlStraße’ you will have to press ‘S’ instead of ß.