Specifications

ManualsBrandsCOMPEX ManualsElectronicsDual Band 4x4 802.11ac Wave 2 Mini PCIe WiFi Module

wireless 11ac wave2 modules

Last Updated: 02/03/21

KEY FEATURES

• Qualcomm Atheros QCA9994

• 2.4GHz, 4x4 MU-MIMO OFDM Technology, up to 600Mbps

physical data rate

• 5GHz, 4x4 MU-MIMO OFDM Technology, up to 1733Mbps

physical data rate

• Dual Band 2.4/5GHz 4x4 WiFi 5 (802.11ac Wave 2)

• MiniPCIe interface with PCIe 2.0

• Heat sink allows free air operation

• Supports IEEE 802.11d, e, h, i, j, k, r, u, v time stamp, w, and z

standards

• Supports Dynamic Frequency Selection (DFS)

Dual Band 2.4/5GHz 4x4 802.11ac Wave 2 MiniPCIe WiFi Module

Designed for High Bandwidth Enterprise Wireless Access Points

Specications

Chipset Qualcomm Atheros QCA9994 ‘Cascade’ Series

System Memory 256Kbit serial I²C bus EEPROM

Reference Design Qualcomm Atheros CAS03

Host Interface MiniPCIe interface with PCIe 2.0

Operating Voltage 3.3V

Power Consumption 9W (Max)

Wireless

2.4GHz 802.11b/g/n

5GHz 802.11a/n/ac

4x U.FL Connectors

Frequency Range

2.412~2.462GHz, 5.150~5.850GHz

Modulation Techniques CCK, OFDM: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM

Channel Spectrum Widths for WLAN Supports 20/40MHz at 2.4GHz, Support 20/40/80/80+80MHz at 5GHz

Supported Operating System CompexWRT or OpenWRT/ LEDE

Certiﬁcation REACH and RoHS Compliance

Environmental Temperature (Industrial Grade) Operating: -40°C to 85°C, Storage: -40ºC to 90ºC

Environmental Humidity, Non-Condensing Operating: 5% to 95%, Storage: Max. 90%

Dimensions (W x H x D) in mm 29.9 x 50.8 x 12.9

*Congurations are subject to change without notications.

Model: WLE1216VX-I

Summary of content (9 pages)

PAGE 1
wireless 11ac wave2 modules Dual Band 2.4/5GHz 4x4 802.11ac Wave 2 MiniPCIe WiFi Module Designed for High Bandwidth Enterprise Wireless Access Points Model: WLE1216VX-I KEY FEATURES • • • • • • • • Qualcomm Atheros QCA9994 2.4GHz, 4x4 MU-MIMO OFDM Technology, up to 600Mbps physical data rate 5GHz, 4x4 MU-MIMO OFDM Technology, up to 1733Mbps physical data rate Dual Band 2.4/5GHz 4x4 WiFi 5 (802.11ac Wave 2) MiniPCIe interface with PCIe 2.0 Heat sink allows free air operation Supports IEEE 802.
PAGE 2
hardware guide - WLE1216vX WLE1216VX Component Map UFL connector: CH0,CH1,CH2,CH3 miniPCIe Interface Power Requirements DC Power 3.
PAGE 3
OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.
PAGE 4
Antenna (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co-located with any other transmitter or antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid, and the FCC ID/IC cannot be used on the final product.
PAGE 5
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 6
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 7
Industry Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 8
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires.
PAGE 9
Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.