0200 User Manual Rev.
Compuprint Products Information Thanks for choosing the 10200 printer. Your printer is a reliable working equipment that will be very useful in your daily job. Our printers have been designed to be compact and respectful of the work environment. They offer a wide range of features and multiple functions that confirm the high technological level reached by the printers with Compuprint brand.
FCC Notes This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Table of Contents Compuprint Products Information ....................... ii FCC Notes.............................................................. iii Canadian D.O.C. Radio Interference Regulation iii EEC Regulations ................................................... iii Table of Contents.................................................. iv Getting to Know Your Printer ............................... 1 Printer Features ....................................................................
Getting to Know Your Printer Printer Features • 24 Needle Print Head • 136 columns @ 10 cpi • High Speed Draft printing at 1100 cps, Draft printing at 800 cps and LQ printing at 133 cps • IBM Proprinter XL24/XL24 AGM, Personal Printer 2391+ and EPSON LQ Series emulations • Multiple copies (1 original and 7 copies) • Automatic paper path selection • Easy operability via operator panel setup and S/W commands • Use of all specific features by means of the Specific Software Driver which is applicable to the mos
Unpacking Your Printer The following items are included in the box: Notify any damage to your supplier. C D -R o m ( w ith U se r M a nu al in clu de d ) Front2 Tracto r (op tiona l fo r the PR TN 1 01 m od el) R ibbo n C a rtridg e R ep ack ing S trips P o w er C ab le In stallatio n G uide Never remove any printer cover unless it is necessary for the installation of a printer accessory and expressly described in this manual.
To unpack the printer proceed as follows: Keep the packing material in a safe place. It must be used if you need to repack the printer for shipment. 1. Bring the printer box near the final printer location. 2. Cut the packing ribbons and remove the plastic angles. 3. Remove the polystyrene panel out of the packing box.
4. Remove the accessories out of the packing box and slide the packing box off the printer.
5. Remove the two foam shells on either side of the printer and the plastic bag covering the printer. 6. With the help of another person, move the printer to its final position: - onto the printer cabinet (for the PRTN102 printer model); - onto a stable surface, i.e a table (for the PRTN101 printer model without the printer cabinet option).
Removal of the Shipment Locks 1. Open the tractor area cover and make sure that you remove the shipment lock from the printer. 2. Unscrew the two fixing screws.
3. Open the upper printer cover and remove the fixing strip from the print head. Keep all the packing material, together with the repacking kit, in a safe place. Repack the printer in it original packaging if you need to ship or transport it.
Connecting the Ground Cable For the PRTN102 printer model, or the PRTN101 printer model with the cabinet option connect the ground cable in the interface area on the rear side of the printer cabinet. If the printer is installed on a table, it is not necessary to connect the ground cable.
Printer Parts Front View U pper P rinter C over O perator P ane l Tra cto r A rea C over Printer C abinet Printer H andg rip For the PRTN101 printer model, the printer cabinet is available as an option.
Rear View S e ria l In terface C o nn ecto r P a ra llel In te rfa ce C on nector P o w er C onn ector P rinter C ab inet P a pe r O utp ut S tacker For the PRTN101 printer model, the printer cabinet is available as an option.
Left Side View P o we r S w itch Inside View C olor S hifter Print H ead Pa per B ail Print H ead G ap Ad justm ent R ibbon C artridge Supports 11
Setting Up Your Printer Choosing a Suitable Location Consider the following points when you choose the location for your printer: • The distance between the printer and the host computer must not exceed the length of the interface cable; • The location must be sturdy, horizontal and stable; • Your printer must not be exposed to direct sunlight, extreme heat, cold, dust or humidity (see "Printer Specifications" later); • You need a power outlet compatible with the plug of the printer's power cord; Additional
Ribbon Cartridge Installation Make sure that you are using only Compuprint original consumables. 1. Make sure that the printer is turned off. 2. Find the ribbon cartridge among the accessories.
3. Open the top cover using the handles on the front side of the covers. 4. Turn the printer on. The print carriage prepares for ribbon cartridge installation.
5. Before installing the ribbon cartridge turn the ribbonwinding knob in the arrow direction (located on the cartridge) to take up slack in the ribbon. R ibbon W inding Knob To avoid damage to the ribbon, do not turn the winding knob in the wrong direction. 6. Align the cartridge pins with the locking grooves on the left and right cartridge supports.
7. Slide and insert the ribbon guide between the print head and the ribbon guide mask holding it perpendicular to the print head. Make sure that the ribbon is inserted correctly between the print head and the print head mask. 8. Insert the shifter holder onto the color shifter as shown in the following figure.
9. Turn again the ribbon-winding knob in the arrow direction (located on the cartridge) to take up slack in the ribbon. 10. Push the cartridge down gently until it clips into place at both locking points. 11. Turn the ribbon-winding knob again in the direction of the arrow to take up slack in the ribbon. 12. To ensure that the ribbon guide runs freely along the ribbon, manually move the print carriage horizontally.
Front2 Push Tractor Installation An additional push tractor may be installed on the printer. This Front2 push tractor unit is delivered together with the PRTN102 printer model or is available as an option for the PRTN101 printer model. The Front2 push tractor must be installed on the Front1 push tractor. 1. Find the Front2 push tractor among the accessories. 2. Align the hooks on both sides of the Front 2 tractor with the pins on the Front 1 push tractor.
3. Push the Front 2 tractor until it is fully engaged. 4. Insert the connector cable in the electrical connector located in the lower push tractor.
5. Rotate the Front2 push tractor onto the Front 1 push tractor.
Removing the Front2 Push Tractor If you need to remove the upper push tractor, turn the printer off. Disconnect the connector cable and press on the push buttons to disengage the Front 2 push tractor.
Host Computer Connection This printer can be connected to your host computer via two available interfaces. The interface connectors are located on the rear of the printer. • A bidirectional IEEE1284 parallel interface • A RS-232C/422A serial interface Before connecting the interface cable, make sure that the printer and the host computer are turned OFF . Insert the parallel interface cable into the parallel connector and fasten it by means of the clips.
Software Driver Selection At this point it is necessary to configure your printer for your application package. The installation procedures depend upon the host environment. Follow the instructions in the readme file you find on the CD-ROM. In a WINDOWS 95/98/2000/XP/NT4.0/Millennium® environment the printer supports the Plug & Play feature. The printer drivers of all Compuprint printers can be found at the Internet Address http://www.compuprint.
Power Connection Make sure that the power outlet matches the printers plug. Always use a grounded outlet. 1. Make sure the power outlet is near the printer location and easily accessible. 2. Make sure that the power switch is in 0 position (OFF). 3. Insert the power cable plug into the printer connector and the other power cable end into a convenient outlet (the figure shows the European version).
4. If you need to turn the printer on, press the power switch in the I position (ON).
Selecting the Display Language The display messages for this printer can be displayed in five different languages: English (Default), French, German, Italian and Spanish. To select the language, that you prefer, proceed as follows: 1. Press the PROGRAM key and keep it pressed while powering on the printer until the following message will be displayed: RELEASE KEY 2. When you release the PROGRAM key, the following messages will be displayed: 10200 then, PRINT OUT? NO 3. Press the ↓ key to enter the setup.
Configuring the Printer Operator Panel Presentation The operator panel enables you to perform many of the printer functions including paper path selections, font selection and the printer setup. )URQW )URQW 352*5$0 3$7+ 7($5 3$5.
Display Messages The printer display is used to indicate the printer status or to request an user intervention.
• when there is no paper loaded and the • printer is off line (ON LINE indicator unlit): when there is no paper loaded and the printer is on line (ON LINE indicator lit): ON LINE Load Front1 P rin te r S ta tu s C u rre n t P a p er P a th where: LOAD FRONT 1 LOAD FRONT 2 M1 C u rre n t M a cro Indicates that the currently selected paper path is out of paper. The messages are displayed only for the available paper paths, according to the installed devices.
The following messages appear to indicate other printer conditions or user intervention requests. The list is in alphabetical order. Message Description ALTERNATE This message appears to indicate that the Alternate functions of the operator panel keys have been selected pressing the ALTERNATE key. BUSY This message appears to indicate that the printer is printing. It is busy.
Message Description OPER. INTERRUPTED This message is displayed if the ALTERNATE key has been pressed to interrupt a park procedure. PARKING The printer is parking the fanfold paper. PATH CHANGING The path has been changed and the printer is updating the settings. PRESS A KEY NVM CHANGED The NVM has been changed. Press any key to set the printer. RELEASE KEY This message is displayed when you can release the PROGRAM key in the Selftest selection or in the Power-on Configuration procedure.
Message Description TEAR OFF PAPER EJECT PAPER These messages are displayed when the printer receives a paper ejecting command (TEAR NO item has been selected for the tear-off function) but was not able to execute it, because the paper to be ejected is longer than 18 inch. Tear off the fanfold paper and then press the PARK key to eject the paper.
Indicators Lit when the printer can receive and print data (printer online). ON L INE Blinks when there is data in the buffer and the printer is offline. Unlit when the printer is disabled and the buffer does not contain any data, or during the initialization, setup or tests. P R OGR AM Blinks when one of the printer setup procedures has been selected: Program Configuration or Power-On Configuration.
Function Keys Pressing the function keys it is possible to activate the functions indicated by the word or symbol signed near the key. Each key may have different functions, according to the selected function modes: Normal, Alternate or Program. P rogram F unction 352*5$0 N orma l function 3$7+ 7($5 3$5.
ON LINE Key ON LINE Normal Function Enables or disables the printer. • If this key is pressed while powering the printer on, the self test is printed; the printout is stopped pressing this key again. • In an error condition, once the error cause has been removed, press this key to enable the printer Program Function Pressing this key, the input buffer is cleared an a break (250 msec.) on a serial interface is sent. The message RESET & BREAK is displayed.
FONT Key FONT Normal Function Selects the font to be used with the currently selected pitch. The selected font is valid until the printer is turned off or a new font is selected using this key. ← Program Function Scrolls the parameters of the functions or macros backwards. LF Normal Function Performs a line feed according to the current line spacing settings. MICRO FEED Alternate Function Moves the paper forward in microsteps.
ALTERNATE Key ALTERNATE Normal Function Enables the alternative key functions. If the printer is receiving print data, press the ON LINE key before pressing the ALTERNATE key. If no printing data are in the print buffer, pressing the ALTERNATE key, the printer goes offline. The display then shows ALTERNATE to indicate that the Alternate Function of the keys is enabled (ALTERNATE indicator lit). May be used to abort paper parking procedure.
PATH/PARK Key PATH Normal Function Selects one of the paper paths (FRONT 1 or FRONT 2) in offline status. The parameters of the displayed path are set after 2 seconds without pressing any key. PARK Alternate Function Parks the paper in the currently selected paper path. Key Combinations ONLINE + MACRO + ALTERNATE Normal Function Lock or unlock the access to the printer setups. See later “How to Lock/Unlock the Printer Setups” section.
Printer Setups The main printer setup parameters can be selected via the operator panel. The setup parameters are divided into two printer setups, the Power-On Configuration, that allows a complete configuration at installation time according to the hardware and the emulation types, and the Program Setup, that allows you to set the functions that are the most useful in your daily job.
Leaving the Printer Setups • Pressing the PROGRAM in the Power-On Configuration key the printer exits from the setup and the new settings will be automatically saved. • Pressing the PROGRAM key in the Program Setup, the following choice is offered for the storage of the values set: STORE? QUIT The new settings are not activated and the old settings remain valid. STORE? SAVE The new settings are stored permanently in the NVM (Non Volatile Memory).
Power-On Configuration The default values of the various functions are indicated in bold. Entering the Power-On Configuration 1. Make sure that the printer is turned off. 2. Press and hold the PROGRAM key pressed while powering on the printer until the RELEASE KEY message is displayed.
Main Structure This figure shows the structure of the Power-On Configuration and how to move inside the Setup. P rint out? Y E S P rint out? N O E m u l.
The setup item Functions groups the following printer functions: • • • • • • • • • • • • Buzzer setting, Paper loading sequence, Ribbon type, Bar code density, Text printing direction, Graphics printing direction, Bar code printing direction, Graphics printing speed, Paper path at power on, Language of the display messages, Paper tractor jam sensors, Tear-off position adjustment Printout of the Printer Settings PRINT OUT? NO → or ← PRINT OUT? YES ↓ EMUL. OPTIONS PRINT OUT? NO The Setup is not printed.
Emulation Options This setup defines the available options according to the selected emulation and is structured as follows: Options E m ul. O ptions E m u l E P S O N LQ E m u l IB M ... C har. S et ... C har. S et ... N ation ... N ation ... A uto C R ... A uto C R … A uto L F … A uto L F ... 20 C P I IBM ... P arall.
Setting the Emulation Options Printer Emulation PRINT OUT? NO EMUL. OPTIONS ↑ ↑ EMUL. EPSON LQ → or ← ↓ EMUL. IBM XL24 → or ← PARALL INTERFACE EMUL. IBM XL24AGM → or ← EMUL. IBM 2391 → or ← EMUL. OPTIONS → ↓ CHAR. SET CS2 EMUL EPSON The printer uses the EPSON Series emulation. EMUL IBM XL24 The printer uses the IBM Proprinter XL24 emulation. EMUL IBM XL24AGM The printer uses the IBM Proprinter XL24 AGM emulation. EMUL. IBM 2391 The printer uses the IBM Personal 2391+ emulation.
EPSON Character Sets EMUL. EPSON LQ ↑ CHAR. SET CS1 → or ← CHAR. SET CS2 → or ← CHAR. SET ITALIC → or ← ↓ NATION CP437 These items select the character set to be used in EPSON emulation. IBM Character sets EMUL. IBM xxx ↑ CHAR. SET CS1 → or ← CHAR. SET CS2 → or ← ↓ NATION CP437 These items select the character set to be used in IBM Proprinter emulation.
EPSON National Character sets CHAR.
IBM National Character Sets CHAR.
CR Code Behavior NATION xxx ↑ AUTO CR NO → or ← AUTO CR YES → or ← ↓ AUTO LF NO AUTO CR NO No automatic carriage return is performed after a LF, VT or ESCJ code. AUTO CR YES The printer performs an automatic carriage return after a LF, VT or ESCJ code.
LF Code Behavior AUTO CR xx ↑ AUTO LF NO → or ← AUTO LF YES → or ← AUTO LF HOST → or ← ↓ 20 CPI IBM NO or EMUL. OPTIONS AUTO LF NO No Automatic LF after CR. AUTO LF YES Automatic LF after CR. AUTO LF HOST Only in EPSON emulation. The printer checks the AUTOFEEDXT signal coming from the host and executes an automatic LF after CR, if the signal is low.
IBM Compressed Printing These items are displayed only if the IBM emulation is selected. AUTO LF NO ↑ 20 CPI IBM NO → or ← 20 CPI IBM YES → or ← ↓ EMUL. OPTIONS 20 CPI IBM NO The compressed printing is performed at 17.1 cpi. 20 CPI IBM YES The compressed printing is performed at 20 cpi.
Parallel Interface This setup defines the use of the parallel interface and is structured according to the interface specific parameters. Parallel Interface Parameters P arall Interface S erial Interface RU 1284 B id ir. I/F C X .
Setting the Parallel Interface Parameters Interface Type EMUL. OPTIONS PARALL INTERFACE ↑ ↑ 1284 BIDIR. I/F → or ← ↓ CX. PARALLEL I/F → or ← SERIAL INTERFACE ↓ or SELECT-IN HOST PARALL INTERFACE → LAN INTERFACE 1284 BIDIR. I/F Bidirectional IEEE 1284 parallel interface. CX. PARALLEL I/F Centronics type parallel interface (monodirectional). Setting the Select-In Signal 1284 BIDIR .
Number of Data Bits SELECT-IN HOST ↑ DATA BITS 8 → or ← DATA BITS 7 → or ← ↓ INPUT BUFFER 2K Selection of the number of data bits: 7 or 8 Input Buffer Size DATA BITS 8 ↑ INP. BUFFER 256 → or ← INP. BUFFER 2K → or ← INP. BUFFER 12K → or ← INP. BUFFER 32K → or ← INP. BUFFER 64K → or ← INP. BUFFER 128K → or ← ↓ PARALL. INTERFACE Selects the input buffer size.
Serial Interface These serial interface functions will display only if the serial I/F board is installed in the printer. This setup defines the use of the serial interface and is structured according to the interface specific parameters. Serial Interface Parameters S erial Interface S erial I/F N o S erial I/F ... B aud 9600 B aud ... D ata Bits 8 D ata Bits 7 P arity N on e P arity ... H and sh ake D TR H and sh ake X on /X of C onn ection L ocal C onn ect.
Setting the Serial Interface Parameters Interface Type PARALL INTERFACE SERIAL INTERFACE ↑ ↑ SERIAL I/F NO → or ← ↓ SERIAL I/F 232 → or ← FUNCTIONS SERIAL I/F 422 → or ← SERIAL INTERFACE → ↓ BAUD 9600 SERIAL I/F NO The serial interface is disabled SERIAL I/F 232 Defines the usage of the serial interface RS-232/C SERIAL I/F 422 Defines the usage of the serial interface RS-422/A 56
Baud Rate SERIAL I/F NO ↑ BAUD 300 → or ← BAUD 600 → or ← BAUD 1200 → or ← BAUD 2400 → or ← BAUD 4800 → or ← BAUD 9600 → or ← BAUD 19200 → or ← BAUD 38400 → or ← ↓ DATA BITS 8 The baud rate is selected in bits per second. The above values can be selected. Number of Data Bits BAUD 9600 ↑ DATA BITS 8 → or ← DATA BITS 7 → or ← ↓ PARITY NONE Selection of the number of data bits: 7 or 8.
Parity Check DATA BITS 8 ↑ PARITY NONE → or ← PARITY ODD → or ← PARITY EVEN → or ← PARITY MARK → or ← PARITY SPACE → or ← ↓ HANDSHAKE DTR PARITY NONE Data does not have a parity bit, i.e. 8 bit data are transferred and the parity check is disabled. PARITY ODD Parity check is enabled for odd parity. PARITY EVEN Parity check is enabled for even parity. PARITY MARK Parity check is disabled and the transmitted parity bit is always a Mark.
Handshake Protocol PARITY NONE ↑ HANDSHAKE DTR → or ← HANDSHAKE XONXOF → or ← ↓ CONNECTION LOCAL HANDSHAKE DTR The Handshake is performed using the DTR Protocol. HANDSHAKE XONXOF The Handshake is performed using the XON-XOFF Protocol. Connection Type HANDSHAKE DTR ↑ CONNECTION LOCAL → or ← CONNECT. REMOTE → or ← ↓ INPUT BUFFER 2K Selects the connection type: local or remote.
Input Buffer Size CONNECTION LOCAL ↑ INP. BUFFER256 → or ← INP. BUFFER 2K → or ← INP. BUFFER12K → or ← INP. BUFFER32K → or ← INP. BUFFER64K → or ← INP. BUFFER128K → or ← ↓ SERIAL INTERFACE Selects the input buffer size.
LAN Interface The following LAN interface functions will display only if the Ethernet 10/100 Mbit interface board is installed in the printer. This setup defines the use of the LAN interface and is structured according to the interface specific parameters. LAN Interface Parameters L A N Interfa ce IP A ssign F ixed IP A ssign … Init IP A dd ress … Init IP A dd ress … S M T P E na bl. N o S M T P E na bl.Yes N o vell E n. N o N o vell E n.
IP Assignment PARALL INTERFACE LAN INTERFACE ↑ ↑ IP ASSIGN FIXED → or ← ↓ IP ASSIGN DHCP → or ← FUNCTIONS IP ASSIGN ARP → or ← LAN INTERFACE → ↓ INIT IP ADDRESS 127.000.000.000 IP ASSIGN FIXED Assigns the static or fixed IP address. IP ASSIGN DHCP Assigns the dynamic IP address (DHCP protocol). IP ASSIGN ARP Assigns the user’ s defined IP address (ARP protocol). Init IP Address IP ASSIGN FIXED INIT IP ADDRESS 000.000.000.000 → or ← INIT IP ADDRESS … → or ← INIT IP ADDRESS 255.255.255.
Init Net Mask INIT IP ADDRESS 127. 000.000.000 ↑ INIT NET MASK 000.000.000.000 → or ← INIT NET MASK … → or ← INIT NET MASK 255.255.255.255 → or ← ↓ DEF. GATEWAY ID 000.000.000.000 These values set the INIT net mask number. This number is represented by a decimal notation where the decimal values are divided by points in four fields. Each field ranges between 0 and 255.
Init Host Name DEF. GATEWAY ID 000.000.000.000 ↑ INIT HOST NAME …………… → or ← PROGRAM key ↓ INIT WORKGROUP CPG_GROUP The host is identified by a name. This function allows to create the name of the init host using a 15character string. Use the ← or → keys to increase or decrease the values in one field and the p or nkeys to move to the next field (p to move to the right and n to move to the left). Press the PROGRAM key to save the selected init host name. The default name is CPG_xxxxxx.
Enable/Disable the SMTP Service INIT WORKGROUP CPG_GROUP ↑ → or ← SMTP ENABL. NO SMTP ENABL. YES ↓ ↓ NOVELL EN. NO MAIL SERV.ADDRES 000.000.000.000 SMTP ENABL. NO Disables the SMTP (Simple Mail Transfer Protocol) service, that is disables the reception/transfer/error service of the e-mail. SMTP ENABL. YES Enables the SMTP (Simple Mail Transfer Protocol) service, that is enables the reception/transfer/error service of the e-mail. Mail Server Address This item is displayed only if the SMTP ENABL.
E-mail Address This item is displayed only if the SMTP ENABL. function is selected YES. MAIL SERV.ADDRES 000.000.000.000 ↑ EMAIL ADDRESS xxxxxxxxxxx → or ← ↓ SENDER ADDRESS xxxxxxxxxxx This function allows to write the e-mail address where you can notify the failures. Use the ← or → keys to increase or decrease the values in one field and the p or nkeys to move to the next field (p to move to the right and n to move to the left). Press the PROGRAM key to save the e-mail address.
Enable/Disable the Novell Service SMTP ENABL. NO ↑ → or ← NOVELL EN. NO NOVELL EN. YES ↓ ↓ IP ASSIGN FIXED NOV. SERVER NAME xxxxxxxxxxx NOVELL EN. NO Disables the service to see the printer via NOVELL network. NOVELL EN. YES Enables the service to see the printer via NOVELL network. Print Server Name in Novell Network This item is displayed only if the NOVELL EN. function is selected YES. NOVELL EN. YES ↑ NOV. SERVER NAME ……….. →o← ↓ NOV.
Printer Name in Novell Network This item is displayed only if the NOVELL EN. function is selected YES. NOV. SERVER NAME xxxxxxxxxxx ↑ NOV. PRINTER NAME …………… → or ← ↓ NOV. QUEUE NAME xxxxxxxxxxx This function allows to create the printer name in Novell network. Use the ← or → keys to increase or decrease the values in one field and the p or nkeys to move to the next field (p to move to the right and n to move to the left). Press the PROGRAM key to save the printer name. The default printer name is PS1.
Frame Type in Novell Network This item is displayed only if the NOVELL EN. function is selected YES. NOV. QUEUE NAME xxxxxxxxxxx ↑ NOV.FRAME TYPE 0 → or ← NOV. FRAME TYPE … → or ← NOV. FRAME TYPE 30 → or ← ↓ NOVELL EN YES These values select the frame type number in Novell network. This number ranges between 0 and 30. The default frame type number is 0.
Functions This item groups various printer functions, with which you can configure the printer. Functions Group Parameters Fu nctio ns B uzzer Yes B uzzer N o S equen ce N one S eq. F 1 + F 2 Pu sh R ibbon Black R ibbon C olor B ar C ode 90 B ar C ode 60 Text D irect B i Text D irect U ni G rap h D irect B i G rap h D irect U ni B arcodes D ir. U ni B arcodes D ir. Bi G rap h H .S N o G rap h H .S Yes P.O n P ath M acro P.O n P ath Last M enu E N G LIS H M enu … F1 Jam Se ns.
Setting the Functions Group Items Enable/Disable the Buzzer SERIAL INTERFACE or LAN INTERFACE FUNCTIONS ↑ ↑ → BUZZER YES → or ← ↓ BUZZER NO → or ← BACK TO MFG: NO ↓ FUNCTIONS SEQUENCE NONE Enable or disables the buzzer. Paper Loading Sequence BUZZER YES ↑ SEQUENCE NONE → or ← SEQ. F1+F2 PUSH → or ← ↓ RIBBON BLACK The SEQ. F1+F2 PUSH item is displayed only if the Front2 push tractor option is installed. SEQUENCE NONE The paper is fed only through the path selected by operator panel. SEQ.
Ribbon Type Selection SEQUENCE NONE ↑ RIBBON BLACK → or ← RIBBON COLOR → or ← ↓ BAR CODE 60DPI Selects the ribbon type to be used with the printer: black or color. Bar Code Density RIBBON BLACK ↑ BAR CODE 60DPI → or ← BAR CODE 90DPI → or ← ↓ TEXT DIRECT BI Selects the bar code print density: 60 or 90 dpi.
Text Print Direction BAR CODE 60DPI ↑ TEXT DIRECT BI → or ← TEXT DIRECT UNI → or ← ↓ GRAPH DIRECT BI Selects the print direction for text: bidirectional or unidirectional. Graphics Print Direction TEXT DIRECT BI ↑ GRAPH DIRECT BI → or ← GRAPH DIRECT UNI → or ← ↓ BARCODES DIR.UNI Selects the print direction for graphics: bidirectional or unidirectional.
Bar Codes Print Direction GRAPH DIRECT BI ↑ BARCODES DIR. BI → or ← BARCODES DIR. UNI → or ← ↓ GRAPH H.S. YES Selects the print direction for bar codes: bidirectional or unidirectional. Graphics Printing Speed Selection BARCODES DIR. UNI ↑ GRAPH H.S. NO → or ← GRAPH H.S. YES → or ← ↓ P. ON PATH MACRO GRAPH H.S NO Selects graphics printing (bit image data) at normal speed mode. GRAPH H.S YES Selects graphics printing (bit image data) at high speed mode.
Paper Path at Power-On GRAPH H.S. YES ↑ P. ON PATH MACRO → or ← P. ON PATH LAST → or ← ↓ MENU ENGLISH P. ON PATH MACRO The paper path at power-on is the one from the default Macro. P. ON PATH LAST The paper path at power-on is the last one that was selected before the printer was powered off. Selection of the Language of the Display Messages P. ON PATH MACRO ↑ MENU ENGLISH → or ← MENU ITALIANO → or ← MENU FRANCAIS → or ← MENU ESPANOL → or ← MENUE DEUTSCH → or ← ↓ F1 JAM SENS.
Enable/Disable Lower Tractor Jam Sensor MENU ENGLISH ↑ F1 JAM SENS. Y → or ← F1 JAM SENS. N → or ← ↓ F2 JAM SENS. Y or TEAR ADJUST:xxx F1 JAM SENS. Y Enables the paper jam sensor located in the Lower Front1 Tractor. F1 JAM SENS. N Disables the paper jam sensor located in the Lower Front1 Tractor. Enable/Disable Upper Tractor Jam Sensor This item is displayed only if the Front2 push tractor is installed. F1 JAM SENS. Y ↑ F2 JAM SENS. Y → or ← F2 JAM SENS.
Adjusting the Tear-Off Position F2 JAM SENS. Y or F1 JAM SENS. Y ↑ TEAR ADJUST: - 30 → or ← TEAR ADJUST: ... → or ← TEAR ADJUST: +360 → or ← ↓ BUZZER YES TEAR ADJUST: xxxx These values adjust the distance between the Tear-Off Perforation and the Tear-Off Bar. The values correspond to 1/180 inch units, i.e. the tuning ranges between -1/6 and 2 inch. 0 is the default value. See also “How to Use the Tear-Off Function”, later in this Chapter.
Resetting to Factory Default Values With the BACK TO MFG function it is possible to reset all items in the Power On Configuration Setup and in the Program Setup to their factory default values. This may be useful if you do not remember the values you set in the setups, or because you simply changed you mind about the settings you have just done. The default values for the setup items are indicated in bold.
Program Setup The default values of the various functions are indicated in bold. Entering the Program Setup Press the PROGRAM key when the printer is turned on and is offline or online without printing. The following message will be displayed: PRINT OUT? NO The figure in the following page shows the structure and how to move inside the Program Setup.
Main Structure Print out? No Print out? Yes U ser Macro M acro# 1 Line sp. 6 lpi ... … M acro#4 Line sp. ... M AC RO PAR AM ETE R BL OC K N ext M acro? N o C onfig. Menu No C onfig. Menu Yes H ex D um p N o H ex D um p Yes N ext M acro? Yes Parall.
Printout of the Printer Settings PRINT OUT? NO → or ← PRINT OUT? YES ↓ USER MACRO PRINT OUT? NO The setup is not printed. PRINT OUT? YES The printer setup is printed. The printout starts as soon as you select this value. NOTE: The Program setup printout indicates: • the currently selected values, • the current selected macro is marked with the #x# symbols (USER MACRO #x#), • the current firmware release.
User Macro The USER MACRO item allows to prepare four printing environments (MACRO#1, MACRO#2, MACRO#3 and MACRO#4). Each macro is composed of a group of parameters which define a configuration that can then be recalled to easily set the printer for four printing environments. Selection of the User Macro PRINT OUT? NO USER MACRO ↓ ↑ MACRO # 1 → or ← ↓ MACRO # 2 → or ← CONFIG MENU NO MACRO # 3 → or ← MACRO # 4 → or ← USER MACRO → ↓ LINE SP.
User Macro Parameters User macro M acro #1 M acro #2 M acro #3 M acro #4 Line sp. 6 lpi Line sp. ... Line Sp. Lock No Line Sp. Lock Yes Length 66 Lines Length ... Top of Form 0 Top of Form … Ignore F.F. No Ignore F.F.
R ig ht M argin 136 R ig ht M argin … S lash Zero N o S lash Zero Yes P ath F ront 1 P ath Front 2 ... Tear N orm al Tear … Tear D elay 1 Tear D elay … S tron g im p act S oft im pact P erfo r. Safe N o P erfo r. Safe Yes Q u iet P rint O ff Q u iet P rint O n A utogap 0 A utogap ... Tuning: H oriz 0 Tuning: H oriz ... Tuning: Vert 0 Tuning: Vert ... M acro-> M F G N o M acro-> M F G Yes N ext M acro? N o N ext M acro? Yes C onfig.
Line Spacing MACRO # 1 ↑ MACRO# 1 → LINE SP. 6 LPI → or ← LINE SP. 8 LPI → or ← LINE SP. 12 LPI → or ← LINE SP. 3L/30MM → or ← LINE SP. 4L/30MM → or ← LINE SP. 6L/30MM → or ← LINE SP. 8L/30MM → or ← LINE SP.12L/30MM → or ← ↓ LINE SP LOCK NO These values define the line spacing in lines/inch (6, 8, 12) or in lines per 30 mm (3, 4, 6, 8, 12). Line Spacing Lock LINE SP. 6 LPI ↑ LINE SP. LOCK NO → or ← LINE SP. LOCK YES → or ← ↓ LENGTH xxx LINE SP.
Page Length LINE SP. LOCK NO ↑ LENGTH 1 LINE → or ← LENGTH ... LINES → or ← LENGTH 244 LINES → or ← ↓ TOP OF FORM 0 These items set the page length for fanfold paper in number of lines depending on the current vertical spacing. Default value is 66 lines. Top of Form LENGTH xx ↑ TOP OF FORM 0 → or ← TOP OF FORM … → or ← TOP OF FORM xxx → or ← ↓ IGNORE F.F. NO These items set the top of form. The values range between 0 and the page length - 1.
Form Feed (FF) Command TOP OF FORM 0 ↑ IGNORE F.F. NO → or ← IGNORE F.F. YES → or ← ↓ SKIPOVER 0 IGNORE F.F. NO IGNORE F.F. YES The Form Feed (FF) command is always executed. The Form Feed (FF) command is ignored when the paper is in the top of form (TOF) position. A Form Feed can be performed if the LOAD/FF key is pressed. Skip Over Perforation IGNORE F.F. NO ↑ SKIPOVER 0 → or ← SKIPOVER … → or ← SKIPOVER xxx → or ← ↓ DRAFT MODE HS These items set the skipover perforation.
Draft Print Mode Selection SKIPOVER 0 ↑ DRAFT MODE HS → or ← DRAFT MODE NORM → or ← DRAFT MODE BEST → or ← ↓ QUALITY LQ DRAFT MODE HS The printer performs the draft printing at high speed. DRAFT MODE NORM The printer performs the draft printing at normal speed. DRAFT MODE BEST The printer performs the draft printing at low speed to obtain better quality printing.
Font Selection QUALITY LQ ↑ FONT Draft → or ← FONT Courier → or ← FONT OCR-B → or ← FONT Gothic → or ← FONT Prestige → or ← FONT Present → or ← FONT OCR-A → or ← FONT Script → or ← ↓ PITCH 10 CPI Selects the fonts. OCR-A is displayed only if a non proportional pitch has been selected.
Pitch Selection FONT Draft ↑ PITCH 5 CPI → or ← PITCH 6 CPI → or ← PITCH 7.5 CPI → or ← PITCH 8.5 CPI → or ← PITCH 10 CPI → or ← PITCH 12 CPI → or ← PITCH 15 CPI → or ← PITCH 17.1 CPI → or ← PITCH 20 CPI → or ← PITCH 24 CPI → or ← PITCH PROP → or ← ↓ 15&24CPI MICRO These items set the horizontal spacing in characters per inch. The PITCH PROP item sets proportional character spacing.
Micro Dot Print Mode PITCH 10 CPI ↑ 15&24CPI MICRO → or ← 15&24CPI NORMAL → or ← ↓ PITCH LOCK NO 15&24CPI MICRO 15&24CPI NORMAL The print matrix uses 8 x 8 dots only if the horizontal spacing is 15 or 24 cpi. (micro mode). The print matrix uses 12 x12 dots (normal mode). Pitch Lock 15&24CPI MICRO ↑ PITCH LOCK NO → or ← PITCH LOCK YES → or ← ↓ LEFT MARGIN 0 PITCH LOCK NO PITCH LOCK YES Setting this item, the pitch can be changed by software or operator panel.
Left Margin PITCH LOCK NO ↑ LEFT MARGIN 0 → or ← LEFT MARGIN ... → or ← LEFT MARGIN xxx → or ← ↓ RIGHT MARGIN 136 The Left Margin is set in number of columns (depending on the current pitch) starting from the physical left edge. Right Margin LEFT MARGIN 0 ↑ RIGHT MARGIN. 2 → or ← RIGHT MARGIN. ... → or ← RIGHT MARGIN. xxx → or ← ↓ SLASH ZERO NO The Right Margin is set in number of columns (depending on the current pitch) starting from the physical left edge. The default value is 136.
Zero Character Printing RIGHT MARGIN 136 ↑ SLASH ZERO NO → or ← SLASH ZERO YES → or ← ↓ PATH FRONT 1 You can select the Zero character printing with or without a slash. Paper Path Selection This function defines the default paper path for the current macro. SLASH ZERO NO ↑ PATH FRONT 1 → or ← PATH FRONT 2 → or ← ↓ TEAR NORMAL PATH FRONT 1 Paper loading with the Front1 tractor (low position). PATH FRONT 2 Paper loading with the Front2 tractor (up position).
Tear-Off Mode PATH FRONT 1 ↑ TEAR NORMAL → or ← TEAR AUTOMATIC → or ← LABEL → or ← TEAR NO → or ← ↓ TEAR DELAY 1 TEAR NORMAL The Tear-Off Function is performed pressing the TEAR key when the printer is offline. TEAR AUTOMATIC When the printer is not receiving any data, the paper is moved to the Tear-Off position. It is returned to the Tear-Off position as soon as it receives printing data. LABELS This item must be set when printing on labels, in order to avoid paper jams.
Tear Delay Mode TEAR NORMAL ↑ TEAR DELAY 1 → or ← TEAR DELAY … → or ← TEAR DELAY 5 → or ← ↓ STRONG IMPACT This item defines the time that printer uses to move paper to the Tear-Off position in automatic tear mode. The range of the tear delay is between 1 and 5 seconds. The default value is 1 sec. Print Impact Strength TEAR DELAY 1 ↑ STRONG IMPACT → or ← SOFT IMPACT → or ← ↓ PERFOR. SAFE NO STRONG IMPACT The impact strength of the print head is set for printing on multicopy paper.
Paper Perforation This function allows to move the print head aside the paper when the fanfold paper perforation passes between the mylar and the print bar, to avoid paper jams. STRONG IMPACT ↑ PERFOR. SAFE NO → or ← PERFOR. SAFE YES → or ← ↓ QUIET PRINT OFF The function is disabled. The print head remains in its position, when the perforation of the paper passes. PERFOR. SAFE YES The function is enabled. The print head is moved aside, when the perforation passes. PERFOR.
Adjusting the Distance of the Print Head QUIET PRINT OFF ↑ AUTOGAP -5 → or ← AUTOGAP ... → or ← AUTOGAP +3 → or ← MANUAL GAP → or ← FIXED GAP 0.3 → or ← FIXED GAP ... → or ← FIXED GAP 9.3 → or ← ↓ TUNING:.HORIZ 0 AUTOGAP xxx Selecting one of these values sensing the paper thickness. Negative values reduce the distance between the print head and the paper. Default value is AUTOGAP 0. MANUAL GAP Selecting this item, the print head must be adjusted manually.
Horizontal Character Tuning AUTOGAP 0 ↑ TUNING:HORIZ 0 → or ← TUNING:HORIZ ... → or ← TUNING:HORIZ 60 → or ← ↓ TUNING: VERT 0 These values adjust the distance between the left paper margin and the first print character. The values correspond to 1/120 inch units, i.e. the tuning ranges between 0 and 0,5 inch. Vertical Character Tuning TUNING:.HORIZ 0 ↑ TUNING:VERT. -30 → or ← TUNING:VERT. ... → or ← TUNING:VERT.
Resetting the Macro Parameters to the Factory Defaults TUNING.VERT. 0 ↑ MACRO -> MFG NO → or ← MACRO -> MFG YES → or ← ↓ NEXT MACRO? NO MACRO -> MFG NO The new values set for the macro parameters will be the used. MACRO -> MFG YES The values set for the macro parameters will be reset to their factory defaults.
Selecting Another Macro MACRO -> MFG NO ↑ NEXT MACRO? NO ↓ CONFIG MENU NO → or ← NEXT MACRO? YES ↓ MACRO # 1 To pass over to another macro, select NEXT MACRO YES. Pressing the ↓ or ↑ key the item MACRO#1 is displayed, then press the → key to pass over to MACRO#2 (MACRO CHANGING is displayed). When passing over from one macro to another, the fanfold paper loaded from the paper path, selected in the previous macro, will be automatically parked (TEAR IF NECESS/PARK PAPER is displayed).
Passing over to the Power-On Configuration At this point of the setup, it is possible to pass over to the Power On Configuration functions setting. NEXT MACRO NO ↑ CONFIG MENU NO → or ← CONFIG MENU YES ↓ ↓ HEX DUMP NO PARALL INTERFACE These items are self-explaining. Hexadecimal Dump CONFIG MENU NO ↑ HEX DUMP NO → or ← HEX DUMP YES ↓ STORE? QUIT If you select HEX DUMP YES, press the PROGRAM key to set this item.
Storing the values HEX DUMP NO ↑ STORE? QUIT → or ← STORE? SAVE → or ← STORE? CURRENT → or ← PROG EXIT STORE? QUIT This setting does not save any of the new values set. The values set previously will be used. STORE? SAVE The values set are stored permanently (in the NVM) and will be used until they are changed by the operator. STORE? CURRENT The values set are valid until the printer is turned off. When you turn the printer on again, the values set in the preceding setup setup will be used.
How to Select the Paper Path The paper can be loaded into the printer using different paper paths. The messages indicating the paper paths are shown only if the corresponding loading device is installed on the printer. Proceed as follows: 1. Press the ON LINE key to put the printer offline (ON LINE indicator unlit). 2. Press the PATH key, according to the installed devices the following messages are displayed: LOAD FRONT 1 For the Front1 tractor paper path. LOAD FRONT 2 For the Front2 tractor paper path.
How to Use the Tear-Off Function This function is used to match the paper perforation with the tear-off bar. For this function the following values must be set: Selection of the Paper Size 1. Press the PROGRAM key when the printer is disabled or enabled without printing to enter the Program Setup. 2. Press the ↓ key and the following message appears: USER MACRO 3. Press the → key to select the macro for which you want to set the paper size (MACRO#1, MACRO#2, MACRO#3 or MACRO#4). 4.
Adjusting the Tear-Off Position To check the Tear-Off Position proceed as follows: 1. Check if the paper perforation matches the tear-off bar on the printer. 2. To move manually the paper to the Tear-Off position, press the TEAR key when the printer is enabled without printing (TEAR NORMAL function selected YES in the Program Setup). You can leave the manual tear off function by pressing again the TEAR key. If it does not: 1.
Selection of the Tear-Off Mode It is now possible to select the Tear-Off Mode. 1. Press the PROGRAM key when the printer is disabled or enabled without printing to enter the Program Setup. 2. Press the ↓ key. The following message is displayed: USER MACRO 3. Press the → key to select the macro for which you want to set the tear-off mode MACRO#1, MACRO#2, MACRO#3 or MACRO#4). 4.
How to Lock/Unlock the Printer Setups To prevent not expertise persons changing the printer setup parameters, it is possible to lock/unlock the access to the printer setups as follows: • Press ON LINE, MACRO and ALTERNATE keys at the same time and keep them pressed while powering the printer on. As soon as these keys are released, the following messages will be displayed: 10200 then, LOCKED MENU Now the access to the printer setups is locked.
How to Handle the Paper Parking According to the setting of the TEAR item in the Program Setup, the paper parking procedure is performed in different ways. See the following description: If TEAR NO is selected: • • TEAR NO When the paper is positioned at the first printable line and the paper path is changed (changing the Macro or pressing the PATH key) or the PARK key is pressed, the printer performs automatically the parking procedure.
If TEAR NORMAL is selected: • • • When the paper is positioned at the first printable line and the paper path is changed (changing the Macro or pressing the PATH key) or the PARK key is pressed, the printer performs automatically the parking procedure.
If TEAR AUTOMATIC is selected: • • • When the paper is positioned at the first printable line and the paper path is changed (changing the Macro or pressing the PATH key) or the PARK key is pressed, the printer performs automatically the parking procedure.
If LABEL is selected: • • LABEL When the paper is positioned at the first printable line and the paper path is changed (changing the Macro or pressing the PATH key), or the PARK key is pressed the printer automatically ejects the paper towards the rear of the printer.
If at power on the paper is already loaded in a paper path that is different to the paper path used by the macro which is valid at power-on, independently from the setting of the TEAR function, the display shows TEAR IF NECESS./EJECT PAPER. If the paper to be ejected is longer than 18" tear it off and press the PARK key again to perform the paper ejection. In all the above cases the parking procedure may be interrupted pressing the ALTERNATE key. The display shows OPER. INTERRUPTED.
Paper Handling Paper Specifications It is important to use the correct paper for obtaining the best performance. See the information table below: Fanfold Paper Loading Mode Front1 Tractor Front2 Tractor Width 76 to 432 mm 3 to 17 inches 76 to 432 mm 3 to 17 inches Length 76 to 609 mm 3 to 24 inches 76 to 609 mm 3 to 24 inches max. 0.635 mm 0.025 inches max. 0.635 mm 0.
Fanfold Paper Loading Loading Paper Using the Front1 Tractor 1. To select the Front1 tractor paper path, press the PATH key. The display shows: LOAD FRONT1 • If you have been using a different path, the display shows: PATH CHANGING • If you have been using fanfold paper in the Front2 tractor paper path, the printer automatically starts the parking procedure. The display shows alternately: TEAR IF NECESS.
2. Open the tractor area cover turning is upwards until it stops. 3. If installed, rotate the Front2 tractor outside of the printer.
4. Unlock the sprockets of the Front1 tractor moving the sprocket levers up. Slide the left sprocket to the first printing column. For easier understanding some of the following pictures show the printer without the Front 2 tractor installed.
5. Space the paper guides along the tractor bar. Open the sprocket covers of the left and right sprocket. 6. If installed, insert the fanfold paper between the lower and the upper tractor.
7. Hold the fanfold paper in front of the sprockets and insert the paper perforation on the left sprocket pins and close the sprocket cover. 8. Insert the paper on the right sprocket pins, make sure the paper goes under the paper sensor and close the sprocket cover.
9. Match the left sprocket for the first printing position, i.e. the left paper margin must match the eleventh notch on the printer cabinet.
10. Adjust the right sprocket gently to remove slack from the paper. Make sure the paper is not taut. 11. Lock the left and right sprockets moving the sprocket levers down.
12. If installed, reposition the Front2 tractor in its initial position. 13. If your printer is installed on a table, position the paper staple so that the paper is freely fed into the printer. If your printer is installed on the printer cabinet, open the printer cabinet door and lay the paper staple onto the shelf inside the printer cabinet: • Onto the lower shelf if you are using only one paper staple.
15. a) If only the Front1 push tractor is installed: - Press the LOAD/FF key to load the paper into the printer. b) If both the Front1 and the Front2 push tractors are installed: - press the LOAD/FF key to load the paper into the printer; - press the ON LINE key, the LOAD FRONT2 message is displayed; - press the LOAD/FF key to load the paper into the printer; - press the ON LINE key again, the printer now is ready to print. The printed paper is output on the rear side of the printer.
- If the printer is not installed on the cabinet, make sure that there is enough space to stack the printed paper: 123
Loading Paper Using the Front2 Tractor To load paper in this way, it is necessary to install the upper tractor. See before "Front2 Tractor Installation" section. 1. To select the Front2 tractor paper path press the PATH key until the display shows: LOAD FRONT2 • If you have been using a different path, the display shows: PATH CHANGING • If you have been using fanfold paper in the Front 1 tractor paper path, the printer automatically starts the parking procedure. The display shows alternately.
2. Open the tractor area cover turning is upwards until it stops. 3. Unlock the Front2 tractor sprockets moving the sprocket levers up.
4. Space the paper guides along the tractor bar. Open the sprocket covers of the left and right sprocket. 5. Hold the fanfold paper in front of the sprockets and insert the paper perforation on the left sprocket pins and close the sprocket cover. 6. Insert the paper on the right sprocket pins, make sure the paper goes under the paper sensor and close the sprocket cover.
7. Position the left sprocket for printing, matching the left paper margin with the eleventh notch on the printer cabinet and lock it in place. 11 1 2 3 4 5 6 7 8 9 10 8. Adjust gently the right sprocket to remove slack from the paper.
9. Open the printer cabinet door and lay the paper onto the lower shelf inside the printer cabinet. 10. Close the printer cabinet door and the tractor area cover. 11. Press the ON LINE key the following message is displayed: LOAD FRONT2. 12. Press the LOAD/FF key to load the paper into the printer. 13. Press the ON LINE key, now the printer is ready to print. The paper is ejected from the rear of the printer.
Printer Maintenance and Troubleshooting Cleaning the Printer Make sure the printer has been turned off for at least 15 minutes before starting any cleaning operations. Periodic cleaning will help keep your printer in top condition so that it will always provide optimal performance. • Use a neutral detergent or water solution on a soft cloth to clean dirt and grease from the cabinet of the printer.
Replacing the Ribbon Cartridge 1. Make sure that the printer is turned off for at least 15 minutes. Pay attention to the print head because it becomes hot during operation. 2. Open the top printer cover. 3. Slide the ribbon guide out of the print head.
4. Free the shifter holder pushing the tab towards the rear and pulling the shifter holder up. 5. Remove the used ribbon cartridge by lifting it up. Now, you are ready to insert the new ribbon cartridge. See before Installation".
Printing the Self Test If you need to know any printer setting, and to check if the printer is working well, print the selftest. Proceed as follows: 1. Keep the ON LINE key pressed while powering on the printer until the display shows RELEASE KEY. 2. When you release the key, the printer starts the self-test printout. 3. To stop the self-test printing, press the ON LINE key again. The printer is offline.
Error Handling When an error condition occurs: • the printer is disabled; • the first message on the display indicates the error, while the second message gives more details concerning the error conditions. Press always the ON LINE key to reset the error condition. Error Message Description Messages Indication Solution A.G.A NOT OPER ADJUST THE GAP The automatic gap adjustment (A.G.A) is not enabled. Press the ON LINE key to reset the error condition. Adjust the print head gap to a fixed distance.
Messages Indication Solution BUFFER OVERFLOW CHARACTER LOST A buffer overflow condition occurred (for the serial interface). Turn the printer off and on again, or press the PROGRAM and ON LINE key successively to clear the buffer. DATA SET OFF The DSR Signal is not Press the ON LINE key to reset the error connected to the printer and condition. is not ready for data transfer (if the serial interface is selected).
Messages Indication Solution PAPER JAM CHECK ALL PATHS A paper jam error condition occurs in the paper path Check all the paper paths and remove the jammed paper. Press the ON LINE key to reset the error condition. RIBBON BLOCKED CHECK RIBBON The ribbon of the cartridge is Check that the ribbon is correctly inserted. blocked Turn the tension knob to make sure that the ribbon is not jammed. Press the ON LINE key to reset the error condition.
Repacking the Printer for Shipment If you need to ship your printer, it is necessary to repack it to avoid damaging during the transport. Proceed as follows: When repacking the printer always use the original packing material 1. Find the packing material and the repacking kit.
2. Open the upper printer cover and fix the print head with the fixing strip. 3. Open the tractor area cover, move the paper guides to the center of the tractor and fix the two transport screws.
4. With the help of another person move the printer onto the transport foam on the transport pallet. Insert the plastic bag over the printer and the foam shells on both sides of the printer. 33 Kg / 73 Lbs 5. Slide the packing box over the printer and insert the accessories onto the printer. 6. Insert the polystyrene panel into the packing box.
7. Close the packing box and fix it to the transport panel by means of the packing strip, inserting the plastic angles between the packing strip and the carton. 8. Fix the packing strip with the corresponding clips.
Options LAN Interface Board A LAN Interface board is available for the network connections through an integrated Ethernet 10/100 Base-T interface, which coexists with the parallel interface. For the installation of this board, please refer to the Installation Guide you receive together with the Ethernet 10/100 Base-T board. This option is available for both PRTN101 and PRTN102 printer models.
Printer Specifications Printing Characteristics Print Head Matrix 24 pins Print Head Life 800 mil characters (draft) Print Speed (cps) Draft Quality HS Draft Normal Best Draft NLQ LQ 10 cpi 1100 800 400 266 133 12 cpi - 960 480 320 160 micro 15 cpi - 1200 600 400 200 normal 15 cpi - 800 400 - - 17,1 cpi - 685 343 457 226 20 cpi - 800 400 532 266 micro 24 cpi - 960 480 640 320 normal 24 cpi - 960 480 - - Lines per minute @10 cpi in HS Draft mode 600
Print Matrix (horizontal x vertical) Draft Quality HS Draft Normal Best Draft NLQ LQ 10 cpi 9 x 12 12 x 12 12 x 24 36 x 12 36 x 24 12 cpi - 10 x 12 10 x 24 30 x 12 30 x 24 micro 15 cpi - 8x8 8 x 16 24 x 8 24 x 16 normal 15 cpi - 12 x12 12 x 24 - - 17,1 cpi - 14 x12 14 x 24 21 x 12 21 x 24 20 cpi - 12 x 12 12 x 24 18 x 12 18 x 24 micro 24 cpi - 10 x 8 10 x 16 15 x 8 15 x 16 normal 24 cpi - 10 x 12 10 x 24 - - Print Density (characters per inch) Normal 1
Print Styles Draft - Courier- OCR B - Gothic – Prestige - Present - OCR A - Script Print Attributes Sub-superscript, Underline, Overscore, Italics, Emphasized, Double Strike, Shadow, Enlarged, Compressed Graphic Resolution (dots per inch) horizontal 60, 80, 90, 120, 180, 360 vertical 60, 72, 180 Characters Sets Standard PC IBM Character Sets CS1 and CS2 EPSON National Variations USA, France, Germany, United Kingdom, Denmark-1, Sweden, Italy, Japan, Spain-1, Norway, Denmark-2, Spain-2, Latin America
Bar Codes UPC-A, UPC-E, EAN-8, EAN-13, UPC-EAN 2, UPC-EAN 5, Code GP, MSI Plessey, Code BCD, C2/5-3 BAR, Code 39, Code 128, Code 11, Code 93, Codabar, 2/5 Bidirectional, 2/5 Interleaved, 2/5 Industrial, 2/5 Matrix, Postnet Emulations - EPSON LQ Series (ESC/P) - IBM Proprinter XL24 - IBM Personal Printer 2391+ Paper Handling Base Configuration 1 1 FRONT1 TRACTOR Fanfold width: 76 to 432 mm (3 to 17 inches) Copies: 1 original + 7 copies Max. thickness 0,635 mm (0.
Standard Functions • Automatic print head gap adjustment (AGA) • Automatic paper path switching via operator panel or S/W commands • Paper parking • Plug & Play capability • Bar Code printing • Automatic fanfold positioning for tear-off, selectable time-out • Setting and storage of paper format and print conditions for each paper path in the non volatile memory • Printing of the macro characters using the Compuprint native commands Physical and Electrical Characteristics Interfaces Parallel Centronics Com
Reliability MTBF Mean Time between failure: 10000 hours at 25% DC MTTR Mean Time To Repair: 30 minutes Workload 60.000 pages/month (ECMA 132 - 4 hours for 20 days) Printer Life 5 years or 10000 hours @25% Duty Cycle Operating: no limitations Power Supply UNIVERSAL From 90 to 244 VAC Power Output Max.
Paper Conditions Temperature 16° to 24° C Relative Humidity 40% to 60% RH (non condensing) Physical dimensions - Printer Height 350 mm (13,77 inches) Width 720 mm (28,34 inches) Depth 400 mm (15,75 inches) Weight 33 kg Physical dimensions – Printer Cabinet Height printer table: 666 mm (16,92 inches) paper stacker: 512 mm (13,01 inches) Width 726 mm (18,44 inches) Depth without paper stacker: 522 mm (13,26 inches) with paper stacker: 794 mm (20,17 inches) Weight 40 kg 147
Consumables Black ribbon ‘Long Life’ cartridge (25 million characters) PRKN102 Color ribbon cartridge (2 million characters for each band) PRKN103 Options Ethernet 10/100 Base T LAN Interface Board PRAN102 Printer Cabinet (only for PRTN101 model) PRFN102 Front2 Tractor (only for PRTN101 model) PRFN103 Standards CE Mark UL 1950; CSA 22.2 n.
