User's Manual
Table Of Contents
- Home
- Contents
- CSI 2140 Machinery Health Analyzer
- Introduction to the analyzer
- Transfer files with CSI 2140
- AMS Machinery Manager Data Transfer
- AMS Machinery Manager Standalone Data Transfer application
- Communication setup
- Routes and jobs
- Load a route from AMS Machinery Manager into the analyzer
- Load multiple routes from AMS Machinery Manager to the analyzer
- Load a Balance job from AMS Machinery Manager into the analyzer
- Dump a job from the analyzer to AMS Machinery Manager
- Dump a route from the analyzer to AMS Machinery Manager
- Dump a route or job from the analyzer to a folder on a computer
- Analyzer firmware and programs
- Screen captures
- Splash screens
- Printing
- Route
- Route overview
- Manage routes
- Set data collection and display parameters
- Set the plot type for collected data
- Enable or disable Point Advance to automatically move to the next measurement point
- Set High Frequency Detection averages
- Set the route data storage mode
- Set the overlap
- Set the plot type for live data
- Set the overall mode
- Set the integrate mode
- Enable or disable multi-channel group data collection
- Display a summary of data collected for grouped measurement points
- View or hide warning alarms on the Route Data Collection screen
- Restore default values for route data collection and display parameters
- Override the sensor setup for a route
- Enter new speed or load for a measurement point
- Tachometers
- Multiple inputs and measurements
- Collect route data
- Notes
- Plot data
- Run Analyze to collect data for a route measurement point
- View the measurement point setup and history
- Route reports
- Plots
- Analyze and Advanced Analyze
- Analyze overview
- Manage jobs
- Job Setup
- View all saved Analyze jobs
- Create an Analyze job
- Open a saved Analyze job
- Change the job ID
- Edit the equipment ID and description in a job
- Edit the measurement ID and description in a job
- Add a measurement
- Delete a measurement
- Delete data from the current measurement point
- Save a job to equipment in a route
- Set display parameters
- Multi-input measurements
- Sensors and inputs
- Tachometers
- Common data collection parameters
- Collecting data using an Analysis Expert
- Recommended uses of Analysis Experts
- Enable or disable the help text in the Analysis Experts
- High Frequency Analysis
- High Resolution Analysis
- Bearing/Gear Analysis - PeakVue
- Low Frequency Analysis - Slow Speed Technology
- Turning Speed Detection
- Laser Speed Detection
- Bump Tests
- Bump Test Equipment Off
- Bump Test Equipment Running
- Coast Down Peak Hold
- Coast Down Peak and Phase
- Rotor Bar Test Motor Current
- Order Tracking
- Synchronous Analysis
- Synchronous Analysis and Synchronous Averaging
- Orbit Plot
- Cross Channel Amplitude/Phase
- Collect data using Manual Analyze
- Listen to live vibration data in Analyze
- Redo a measurement
- Store data to a route or a job
- Review collected data
- Print an Analyze plot to AMS Machinery Manager
- Print a plot to a memory card
- Reset Analyze defaults
- Advanced Transient
- ODS/Modal
- ODS/Modal overview
- Manage jobs
- Sensors and inputs
- Tachometers
- Set up the plots
- Set up the job
- Collect ODS/Modal data
- Display the data for a measurement point
- Print an ODS/Modal plot to AMS Machinery Manager
- Print an ODS/Modal plot to a memory card
- Balance
- Balance overview
- Manage jobs
- Job Setup
- Sensor Setup
- Measurement Plane Setup
- Weight Plane Setup
- Acquire Data
- Balance correction
- Trim run
- One-run balance job
- Notes
- Balance summary reports
- Review balance data
- Manually enter balance job data
- Calculator Mode
- Determine another location to place weights
- Combine multiple weights on a rotor
- Calculate a new balance solution to use only the available weights
- Calculate weight placement using static and couple components
- Estimate trial weights
- Calculate weight location around the outside rotor circumference
- Calculate new balance solution to use only available locations and weights
- Amplification Factor
- Convert magnitude or frequency values to a different measurement unit
- Tips and additional information
- Balance accessories
- Technical specifications
- Glossary
- Index
beeper
keypad 20
status 20
blue LED 6, 14, 17, 21
Bluetooth audio
connect to paired device 26
enable or disable the radio 25
listen to vibration 69, 138
overview 25
pair a device 26
set up 26
unpair a device 27
Bluetooth device
pair 26
rename 27
set up 26
unpair 27
Bluetooth LED 7
Bluetooth Listener screen 69, 138
Bluetooth radio
enable or disable 25
Bump Test Equipment Off 112
Bump Test Equipment Running 113
Bump Tests 111–113
C
calculator modes 230, 232–234, 236–240
cascade
collect in Analyze 125
plots 126
Circumference Conversion 237
clean the analyzer 2, 3, 31
Coast Down Peak and Phase 114
Coast Down Peak Hold 113
Comm Setup 14–16
Connect For Printing 22
connect to AMS Machinery Manager 38, 40
connection type 37
connectors 7
conserve battery power 21
continuous weight locations 205, 206
create cover page 51
Cross Channel Amplitude/Phase 118
Cross Channel Phase 132
CSI 2140 Four-Channel Input Adapter 31, 32
CSI 430 SpeedVue sensor 110
cursor
add or remove 82
change type 83
gesture 18, 19
D
data storage mode 61
date and time 14–16, 23
DC Volts 130
default display units 23
Demodulation 102–104
Device Offline Printing
create custom page 51
device status icon 38
DHCP 39
discrete weight locations 205, 206
display units 23
E
Enter key 6
estimate trial weights 236
Ethernet
connect to AMS Machinery Manager 40
overview 39
port 7
remote connection 39
set connection type 37
Exponential averaging 101
F
fault frequency 85
field alert 71
file extension
.CPF 51
job 28
route 28
File Utility 14–16, 27
Filtered Orbit 129
firmware
upgrade 48
view current version number 47
Fmax 99
Fmin 99
Force/Exponential window 100
four-channel
connections 32
impact test 137
input adapter 31, 32
ODS/Modal 165
route 68, 69
Transient 147
Four-Channel Input Adapter 31, 32
full screen view 81
Index
270
DRAFT