User's Manual
Table Of Contents
- Home
- Contents
- CSI 2140 Machinery Health Analyzer
- Introduction to the analyzer
- Transfer files with CSI 2140
- AMS Machinery Manager Data Transfer
- AMS Machinery Manager Standalone Data Transfer application
- Communication setup
- Routes and jobs
- Load a route from AMS Machinery Manager into the analyzer
- Load multiple routes from AMS Machinery Manager to the analyzer
- Load a Balance job from AMS Machinery Manager into the analyzer
- Dump a job from the analyzer to AMS Machinery Manager
- Dump a route from the analyzer to AMS Machinery Manager
- Dump a route or job from the analyzer to a folder on a computer
- Analyzer firmware and programs
- Screen captures
- Splash screens
- Printing
- Route
- Route overview
- Manage routes
- Set data collection and display parameters
- Set the plot type for collected data
- Enable or disable Point Advance to automatically move to the next measurement point
- Set High Frequency Detection averages
- Set the route data storage mode
- Set the overlap
- Set the plot type for live data
- Set the overall mode
- Set the integrate mode
- Enable or disable multi-channel group data collection
- Display a summary of data collected for grouped measurement points
- View or hide warning alarms on the Route Data Collection screen
- Restore default values for route data collection and display parameters
- Override the sensor setup for a route
- Enter new speed or load for a measurement point
- Tachometers
- Multiple inputs and measurements
- Collect route data
- Notes
- Plot data
- Run Analyze to collect data for a route measurement point
- View the measurement point setup and history
- Route reports
- Plots
- Analyze and Advanced Analyze
- Analyze overview
- Manage jobs
- Job Setup
- View all saved Analyze jobs
- Create an Analyze job
- Open a saved Analyze job
- Change the job ID
- Edit the equipment ID and description in a job
- Edit the measurement ID and description in a job
- Add a measurement
- Delete a measurement
- Delete data from the current measurement point
- Save a job to equipment in a route
- Set display parameters
- Multi-input measurements
- Sensors and inputs
- Tachometers
- Common data collection parameters
- Collecting data using an Analysis Expert
- Recommended uses of Analysis Experts
- Enable or disable the help text in the Analysis Experts
- High Frequency Analysis
- High Resolution Analysis
- Bearing/Gear Analysis - PeakVue
- Low Frequency Analysis - Slow Speed Technology
- Turning Speed Detection
- Laser Speed Detection
- Bump Tests
- Bump Test Equipment Off
- Bump Test Equipment Running
- Coast Down Peak Hold
- Coast Down Peak and Phase
- Rotor Bar Test Motor Current
- Order Tracking
- Synchronous Analysis
- Synchronous Analysis and Synchronous Averaging
- Orbit Plot
- Cross Channel Amplitude/Phase
- Collect data using Manual Analyze
- Listen to live vibration data in Analyze
- Redo a measurement
- Store data to a route or a job
- Review collected data
- Print an Analyze plot to AMS Machinery Manager
- Print a plot to a memory card
- Reset Analyze defaults
- Advanced Transient
- ODS/Modal
- ODS/Modal overview
- Manage jobs
- Sensors and inputs
- Tachometers
- Set up the plots
- Set up the job
- Collect ODS/Modal data
- Display the data for a measurement point
- Print an ODS/Modal plot to AMS Machinery Manager
- Print an ODS/Modal plot to a memory card
- Balance
- Balance overview
- Manage jobs
- Job Setup
- Sensor Setup
- Measurement Plane Setup
- Weight Plane Setup
- Acquire Data
- Balance correction
- Trim run
- One-run balance job
- Notes
- Balance summary reports
- Review balance data
- Manually enter balance job data
- Calculator Mode
- Determine another location to place weights
- Combine multiple weights on a rotor
- Calculate a new balance solution to use only the available weights
- Calculate weight placement using static and couple components
- Estimate trial weights
- Calculate weight location around the outside rotor circumference
- Calculate new balance solution to use only available locations and weights
- Amplification Factor
- Convert magnitude or frequency values to a different measurement unit
- Tips and additional information
- Balance accessories
- Technical specifications
- Glossary
- Index
G
General Setup 14–16
gestures 18, 19
green LED 6, 12
group number
analyzer 14–16
in route 68, 69
group status timer 64
group summary
Route 76
H
Hanning window 100
hard reboot 13
hardware specifications 257
hardware weights 255
Help key 6, 20
Help text
display for a key 20
enable or disable in Analysis Experts 107
High Frequency Analysis 107
High Frequency Detection averages 61
High Resolution Analysis 108
Home key 6
Home screen 14–16
I
impact test 135–137
impact waveform plots 136
influence coefficient 183, 184
input specifications 259
inputs 95, 149, 168
integration mode 63
J
job
copy to another memory location 28
delete from the analyzer 28
dump to a computer folder 46
dump to AMS Machinery Manager 44
load Balance job 44
move to another memory location 29
K
keypad backlight key 6, 17
keypad beeper 20
keys
lock when carrying 14
overview 6
L
Laser Speed Detection 110
LCD backlight
automatically turn off 21
key 6
set intensity 17
timer 21
LEDs 6, 12, 14, 21
lines of resolution 100
listen to live data 69, 138
load Balance job 44
load MRL 42
load route 41
lock the screen 14, 18
Low Frequency Analysis - Slow Speed Technology 109
M
maintenance 2, 3
Manual Analyze 119, 120, 122–125, 127, 129–132, 134
mark a frequency 82
ME'scope 135, 161
measurement
points for balance 203
specifications 258
view route trend history 76
Measurement Plane Setup 202
measurement units 23
memory
specifications 258
view available 14–16
memory card
insert or remove 24
overview 24
print plot from Adv. Transient 159
print plot from Analyze 141
print plot from ODS/Modal 181
print route report 79
print summary from Balance 228
save files to memory card 22
Memory Utility 14–16, 29, 30
menu navigation 17
multi-channel 31, 32, 68, 69
multi-channel group data 64
multi-plane balance job 187, 193
multiple inputs 31, 32, 68, 69
Multiple Route Load 42
multiple routes
load from AMS Machinery Manager 42
Index
271
DRAFT