User's Manual
Table Of Contents
- Home
- Contents
- CSI 2140 Machinery Health Analyzer
- Introduction to the analyzer
- Transfer files with CSI 2140
- AMS Machinery Manager Data Transfer
- AMS Machinery Manager Standalone Data Transfer application
- Communication setup
- Routes and jobs
- Load a route from AMS Machinery Manager into the analyzer
- Load multiple routes from AMS Machinery Manager to the analyzer
- Load a Balance job from AMS Machinery Manager into the analyzer
- Dump a job from the analyzer to AMS Machinery Manager
- Dump a route from the analyzer to AMS Machinery Manager
- Dump a route or job from the analyzer to a folder on a computer
- Analyzer firmware and programs
- Screen captures
- Splash screens
- Printing
- Route
- Route overview
- Manage routes
- Set data collection and display parameters
- Set the plot type for collected data
- Enable or disable Point Advance to automatically move to the next measurement point
- Set High Frequency Detection averages
- Set the route data storage mode
- Set the overlap
- Set the plot type for live data
- Set the overall mode
- Set the integrate mode
- Enable or disable multi-channel group data collection
- Display a summary of data collected for grouped measurement points
- View or hide warning alarms on the Route Data Collection screen
- Restore default values for route data collection and display parameters
- Override the sensor setup for a route
- Enter new speed or load for a measurement point
- Tachometers
- Multiple inputs and measurements
- Collect route data
- Notes
- Plot data
- Run Analyze to collect data for a route measurement point
- View the measurement point setup and history
- Route reports
- Plots
- Analyze and Advanced Analyze
- Analyze overview
- Manage jobs
- Job Setup
- View all saved Analyze jobs
- Create an Analyze job
- Open a saved Analyze job
- Change the job ID
- Edit the equipment ID and description in a job
- Edit the measurement ID and description in a job
- Add a measurement
- Delete a measurement
- Delete data from the current measurement point
- Save a job to equipment in a route
- Set display parameters
- Multi-input measurements
- Sensors and inputs
- Tachometers
- Common data collection parameters
- Collecting data using an Analysis Expert
- Recommended uses of Analysis Experts
- Enable or disable the help text in the Analysis Experts
- High Frequency Analysis
- High Resolution Analysis
- Bearing/Gear Analysis - PeakVue
- Low Frequency Analysis - Slow Speed Technology
- Turning Speed Detection
- Laser Speed Detection
- Bump Tests
- Bump Test Equipment Off
- Bump Test Equipment Running
- Coast Down Peak Hold
- Coast Down Peak and Phase
- Rotor Bar Test Motor Current
- Order Tracking
- Synchronous Analysis
- Synchronous Analysis and Synchronous Averaging
- Orbit Plot
- Cross Channel Amplitude/Phase
- Collect data using Manual Analyze
- Listen to live vibration data in Analyze
- Redo a measurement
- Store data to a route or a job
- Review collected data
- Print an Analyze plot to AMS Machinery Manager
- Print a plot to a memory card
- Reset Analyze defaults
- Advanced Transient
- ODS/Modal
- ODS/Modal overview
- Manage jobs
- Sensors and inputs
- Tachometers
- Set up the plots
- Set up the job
- Collect ODS/Modal data
- Display the data for a measurement point
- Print an ODS/Modal plot to AMS Machinery Manager
- Print an ODS/Modal plot to a memory card
- Balance
- Balance overview
- Manage jobs
- Job Setup
- Sensor Setup
- Measurement Plane Setup
- Weight Plane Setup
- Acquire Data
- Balance correction
- Trim run
- One-run balance job
- Notes
- Balance summary reports
- Review balance data
- Manually enter balance job data
- Calculator Mode
- Determine another location to place weights
- Combine multiple weights on a rotor
- Calculate a new balance solution to use only the available weights
- Calculate weight placement using static and couple components
- Estimate trial weights
- Calculate weight location around the outside rotor circumference
- Calculate new balance solution to use only available locations and weights
- Amplification Factor
- Convert magnitude or frequency values to a different measurement unit
- Tips and additional information
- Balance accessories
- Technical specifications
- Glossary
- Index
N
Negative averaging 101
Normal averaging 101
notes
add to job 225
add to route measurement point 74
create 73, 225
delete from analyzer 74, 226
delete from job 226
delete from measurement point 74
O
ODS/Modal
acquisition parameters 174
collect data 177
dump a job 44
jobs 166, 167
main menu 162–164
measurement parameters 173
measurement points and symbols 165
overview 161, 162
plots 172
print plot 180
sensors and inputs 168
set reference sensor parameters 176
tachometers 170
one-run balance job 224
orange LED 6, 12
Orbit Plot 117
orbit shapes 118
Order Tracking 101, 115
out of service label 71
Overall mode
Analyze 123
Route 62
overlap 62, 94
P
pair a Bluetooth device 26
Peak and Phase 127
Peak Hold averaging 101
PeakVue
Bearing/Gear Analysis 88–90, 106, 108
input specifications 259
overall mode in Route 62
overview 102–104
transient data 146
plots
set default type in Route 60, 62
change type 82
change X and Y scale 83
expand or compress X axis 84
print 52
select active plot 81
view fault frequency 85
view full screen 81
view peaks 84
point advance 60
power key
overview 6
set hold time 22
standby 14
power on/off 13
power supply
charge battery pack 11
connector 7
precautions 2, 3
precautions 2, 3
print
balance summary report 228
files to AMS Machinery Manager 22
files to memory card 22
route report 78, 79
set default option 22
Program Manager 14–16
programs
add or update 48
delete 14–16
R
radio
enable or disable Bluetooth 25
reboot 13
reference run
acquire 212
overview 211
watchdog checks 213, 214
remote PC 35, 36
Reset key 6
reuse balance job 224
review balance data 228
Rotor Bar Test Motor Current 115
Route
activate 57, 58
Analysis Parameters 77
collect data 69
copy to another memory location 28
delete data 59, 72
delete from the analyzer 28, 59
dump to a computer folder 46
dump to AMS Machinery Manager 45
Index
272
DRAFT