CT-535 Wireless ADSL Router User’s Manual Version A1.
Revision History Modified the following sections: ADSL Mode DHCP NAT Configure Preface This manual provides information to network administrators. installation, operation and applications of the Wireless ADSL Router It covers the Warning Before servicing or disassembling this equipment, always disconnect all power and telephone lines from the wall outlet. Use an appropriate power supply and a UL Listed telephone line cord. Specification of the power supply is stated in Appendix A - Specifications.
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION....................................................................... 7 1.1 Overview ............................................................................................. 7 1.2 Features............................................................................................... 8 1.3 Application........................................................................................... 9 1.4 Front Panel LED Indicators ..............................
.7 Routing .............................................................................................. 34 4.7.1 Enable RIP .....................................................................................35 4.7.2 Static route configuration .................................................................36 4.8 Save................................................................................................... 37 4.9 Reboot .......................................................................
.10.5 5.10.6 5.11 Show VCC quality .........................................................................70 PPPoE .........................................................................................70 PPPoA ............................................................................................. 71 5.12 IGMP ............................................................................................... 71 5.12.1 Add an IGMP entry...............................................................
APPENDIX B: PIN ASSIGNMENTS ...............................................................
Chapter 1 1.1 Introduction Overview The wireless ADSL router combines cutting-edge wireless technology with routing/bridge functions. It enables multiple users to share a high speed ADSL connection, without connecting any wires. To ensure the security of your valuable data the router employs state-of-the-art security features such as WEP data encryption, L2TP, and IpSec pass through.
1.2 Features The Wireless ADSL Router has the following features: Wireless built-in ADSL router IEEE 802.11b compliance 11Mbps/5.
1.3 Application The following diagram shows a typical application of the router, which can be used for G.lite and G.DMT applications.
1.4 Front Panel LED Indicators The front panel LEDs are shown in the picture below, followed by an explanation in the table below. LED Power Color Green Green LAN 1x~4x WLAN Green ADSL Green ALARM Red Mode On Off On Blink Off Blink Off On On Off On Off Function The router is powered up The router is powered down. Ethernet connection is established. Data transmitting or receiving Ethernet connection is not established. Data transmitting or receiving over WLAN The wireless is not installed.
Chapter 2 2.1 Installation Preparing for Hardware Installation The following equipment may be necessary to install the router: A VT-100 compatible terminal This terminal is essential to perform the initial configuration of the router. Normally this is a terminal with a VT-100 emulation program, such as Telix. An RJ45-to-DB9 cable to connect to the Console Port An RS232, RJ45-to-DB9 straight-through cable is required to connect the terminal to the device.
2.2 Hardware Installation Follow the instructions below to complete the hardware connections. Step 1 Connect the Line port to a telephone-line using the supplied RJ-11 cable; or if you wish to connect both the router and a telephone, connect the ADSL port to a micro filter or POTS splitter with a RJ11 connection cable. Step 2 To connect to a hub or PC, use a RJ45 cable. You can connect the router to four LAN devices.
Step 3 (Optional) In order to manage your device through the console port you will need to use a straight-through cable with an RJ-45 connector to attach to the modem, and a female RS-232 connector to connect to the serial port on a PC. The PC must be equipped with a VT-100 emulation program, such as HyperTerminal 5 or Telix. Step 4 Connect the Power jack to the shipped power cord.
Step 5 Attach the power adapter to the wall outlet or other AC source. Step 6 After all connections have been made, turn the power-switch to the on position. After power on, the router performs a self-test. Wait for a few seconds until the test is finished, then the router will be ready to operate. Caution 1: If the router fails to power up, or it malfunctions, first verify that the power supply is connected correctly. Then power it on again.
Chapter 3 Login via the Web Browser This section describes how to manage the router via a Web browser from the remote end. You can use a web browser such as Microsoft Internet Explorer, or Netscape Navigator. It is best to set your display resolution to 1024 x 768. To change the resolution you can go to the Microsoft Windows control panel and click on the Display icon, and change the display settings. You will find the display settings there.
STEP 2: Click OK to submit the settings. STEP 3: Start your Internet browser with the default IP address 192.168.1.1. 3.2 Login Procedure To log on to the system from the Web browser, follow the steps below: STEP 1: Start your Internet browser. STEP 2: Type the IP address for the router in the Web address field. For example, if the IP address is 192.168.1.1, type http://192.168.1.1 STEP 3: You will be prompted to enter your user name and password.
Chapter 4 Web Basic Configuration From the Basic menu bar, you can verify the software version, change passwords, configure the WAN/LAN interfaces, set-up routing, save settings, reboot the device, and retrieve the factory default settings. 4.1 Version Information To verify the software version of your router, from the Basic Menu bar, click on Version Information. The information will display as in the screenshot below. 4.
4.3 ADSL Link Status To view the ADSL link status, click Link Status from the tool bar. The page includes the following information: ADSL Line Status Shows the current status of the ADSL line ADSL Mode Shows the ADSL standard that is currently configured. The standards are: ANSI, G.DMT, G.LITE, MULTI. Upstream Upstream data rate negotiated by DSL link (Kbit/s) Downstream Downstream data rate negotiated by DSL link (Kbit/s) Attenuation Current attenuation (dB) of both near end and far end.
4.4 WAN Setup Click WAN Setup from the tool bar and configure the WAN interface for these services: RFC1483 Bridged, RFC1483 Routed, PPPoE, PPPoA, and MER. The following are the common settings to set up these services. VPI and VCI LLC Encapsulation: With LLC encapsulation, a link control header is added to the Ethernet packet that identifies the protocol type (Ethernet). This allows multiple protocols to be transmitted over the ATM Virtual Circuit.
ADD AN ENTRY To set up the RFC 1483 Bridged, configure the common fields on the top of the page and click the Add button to add the entry. MODIFY AN ENTRY To modify an entry, complete the following steps: STEP 1: Select the entry from the Current ATM PVC List, at the bottom of the WAN Setup page. The current values of the selected entry will display in the upper section of the page. STEP 2: Change the parameters. STEP 3: Click Modify.
STEP 3: Click Modify. DELETE AN ENTRY To delete an entry, Select it from the Current ATM PVC List, at the bottom of the WAN Setup page, and click the Delete button.
4.4.3 PPPoE PPPoE provides service providers similar billing and access control as present in dialup services. In addition, with direct support to Ethernet it provides a low cost solution to supporting multiple hosts at the customer premises. PPPoE provides session authentication using Password Authentication Protocol (PAP) or Challenge Handshake Authentication Protocol (CHAP). Session accounting is possible and conservation of bandwidth can be done by closing down unused sessions.
Idle Timeout: defines the period of idle time (minutes) after which the PPPoE link will be terminated. Authentication: Defines the authentication code: PAP, CHAP or BOTH. If the authentication code is set to BOTH, the router will follow the authentication settings (PAP, CHAP) of the remote DSLAM. Enable DHCP Server: enables the DHCP server. This field is automatically checked when PPPoE is selected. Deselect the field to disable the DHCP server.
4.4.4 PPPoA ADD AN ENTRY To set up PPPoA, click PPPoA, configure the common fields and the following fields. Click the Add button to add the entry. User name and Password: used for remote customers to login upon dialup. PPPoA is manually activated by entering startup commands from the page: Advanced>Configure PPPoA. Authentication: Defines the authentication code: PAP, CHAP or BOTH. If the authentication code is set to BOTH, the router will follow the authentication settings (PAP, CHAP) of the remote DSLAM.
4.4.5 MER MAC Encapsulation Routing (MER) enables the ATU-R to route IP addresses on the RFC1483 bridged link. NAPT function is supported to allow multiple private IP addresses on the LAN to share a public IP address. To set up the MER service, configure the common fields, and then enter the IP Address and Subnet Mask under the MER section of the screen. Click the Add button to add the entry.
4.5 LAN IP Address The default LAN IP address is 192.168.1.1. Click LAN Setup from the menu bar to configure the LAN IP address. Type the IP address and subnet mask. Click Apply to submit the settings. When the new IP address is applied, the Web configuration will be interrupted. Use the new IP address to login.
4.6 WLAN Configuration Parameters that specifically deal with the wireless functions of your router can be accessed from WLAN Setup on the Basic menu bar. The menu is subdivided into several menus: WLAN Basic, WLAN Advanced, WLAN WEP, WLAN Filter, and WLAN Radio. Each of these menus will be covered below. To enable the WLAN radio wave function, click the Radio tab. Tick ON in the Radio Status field, and click the Apply button to submit the setting. To disable it, tick OFF and click the Apply button.
4.6.1 WLAN Basic Parameters To access the WLAN Basic parameters click on the WLAN Basic tab on the WLAN Settings screen. The WLAN Basic Parameters menu includes the parameters listed below. After changing any parameters, click on the Apply button to update the parameters, or click on the Restore button to retain the original settings. IP Address Subnet Mask SSID Channel Enter the IP address for the WLAN interface Enter a subnet mask for the WLAN interface The SSID should match with your client adapters.
4.6.2 WLAN Advanced Functions To access the WLAN Advanced parameters click on the WLAN Advance tab on the WLAN Settings screen. The WLAN Advanced Parameters menu includes the parameters listed below. After changing any parameters, click on the Apply button to update the parameters, or click on the Restore button to retain the original settings. Beacon Interval RTS Threshold Fragmentation DTIM Interval Preamble Type Auth. Type Tx Rates AP Visible Specify the Beacon Interval value.
4.6.3 WLAN WEP Parameters: To access the WLAN WEP parameters click on the WLAN WEP tab on the WLAN Settings screen. This screen is used to set-up WEP security. WEP security uses an encryption keyword on all transmitted and received data. The parameters are described below. After changing any parameters, click on the Apply button to update the parameters, or click on the Restore button to retain the original settings.
Key Type Disabled, 64 bits, 128 bits. This parameter determines the level of security. Disabled means no security, 128 bits provides the highest security. This parameter must match with the remote-clients. Key Generation Select Passphrase to enable automatic key generation, or Manually to manually enter each key. The manual key generation provides two forms, Hex decimal and ASCII string. If Manually is chosen, also configure the fields below.
4.6.4 Mac Filter This screen allows wireless access to be restricted or enabled based on a MAC address. Enter the following parameters. MAC filter status: Disable - de-activates MAC filtering, allow – permits access for the specified MAC address, deny –reject access of the specified MAC address. Click the SET button to submit the setting. (the status will impact all MAC Addresses that have been entered as filters) MAC address: Enter the MAC address of the access point, and then click the Add button.
4.7 Routing Click Routing Setup from the menu bar to configure the routing functions. Routing functions includes RIP and static routing.
4.7.1 Enable RIP To enable RIP, complete the following steps: STEP 1: Click Routing Setup from the menu bar. STEP 2: Select On in the Rip Status field. STEP 3: Select a RIP Version (Version 1 or Version 2) from the Version field. STEP 4: Click Apply to submit the settings. STEP 5: After submitting the new Rip settings, the List of Static Routes will be updated to reflect this change.
4.7.2 Static route configuration The Routes Configuration field allows you to add, modify, and delete a static route. Type the Destination Network ID, subnet mask, and next hop IP and click a button below to perform the requested function. Add: To add a static route complete the following steps: STEP 1: Click Routing Setup from the menu bar.
4.8 Save To save the settings to Flash, click Save & Reboot from the menu bar. In the main pane, click Save.
4.9 Reboot To reboot the router, click Save & Reboot from the menu bar. In the main pane, click on Reboot.
4.10 Retrieve default settings To retrieve the default settings, click Erase & Reboot from the menu bar. In the main pane, click Erase.
Chapter 5 5.1 WEB Advanced Configuration ADSL Mode Click the ADSL Mode button from the Advanced menu bar. • There are four ADSL modes: ANSI, G.DMT, G.LITE, MULTI. The default ADSL mode is MULTI. MULTI mode enables the device to auto-adjust its mode to match the remote CO DSLAM. You can specify an ADSL mode on this page, and click the Apply button to submit the settings. • Trellis Code: Enable, Disable • ADSL CO Vendor: Default, Broadcom, GsV, Infineon and TI.
5.2 VLAN To configure the VLAN function, click VLAN from the Advanced menu bar. The following parameters are displayed: Parameters: VLAN: Select enable or disable to activate/deactivate the VLAN function. Forward DB Type: Used to configure the forwarding database learning type. There are two types of learning for the FDB: Multi and Single. Multiple: the learned entries will be distributed to five databases, (VLAN 1~4 and non-VLAN) Single: the learned entries will be collected into a single database.
5.3 DHCP The Dynamic Host Configuration Protocol (DHCP) provides a centralized approach to allocating IP addresses. It allows IP addresses to be dynamically assigned on an as needed basis, from a pool of addresses. The DHCP server is enabled by factory default with the default IP address of the eth0 to be 192.168.1.1/24. 5.3.1 Enable DHCP Server STEP 1: Click DHCP from the menu bar. There is a default DHCP entry on the screen. The default settings are as follows.
5.3.2 Add DHCP Server To add an entry, click the Add button, and fill out the following parameters. Click Apply to submit the settings. Interface: eth0/wlan0. This configures the interface that will provide the DHCP function. By factory default, the entry for interface eth0 is defined with the gateway address 192.168.1.1, and subnet mask 255.255.255.0. The default entry for interface wlan0 is defined with the gateway address 192.168.101.1, and subnet mask 255.255.255.0.
5.3.3 Disable DHCP Server To stop a DHCP Server, complete the following steps: STEP 1: Click DHCP from the menu bar. STEP 2: Choose a DHCP entry, and click Stop. 5.3.4 Delete DHCP Server To delete a DHCP Server, complete the following steps: STEP 1: Click DHCP from the menu bar. STEP 2: Choose a DHCP entry, and click Delete.
5.4 DHCP Relay The DHCP packet format is based on a BootP packet. As a result, DHCP uses the BootP relay agent to forward DHCP packets. This scheme provides interoperability between existing BootP clients and DHCP servers. The BootP relay agent uses the same criteria and methods for forwarding both DHCP and BootP packets. The DHCP Relay is disabled by default. 5.4.
5.4.2 Disable the BOOTP/DHCP Relay To disable the BOOTP/DHCP Relay complete the following steps: STEP 1: Access the BOOTP/DHCP Relay screen by clicking on DHCP on the Advanced Menu, and then click the BOOTP/DHCP Relay tab. STEP 2: In the DHCP Relay field, select Disable, and enter the IP Address you want to receive BOOT REQUEST or DHCP packets from clients. STEP 3: Click on the Apply button.
5.5 DHCP Client Note: Before starting the DHCP Client function, the user needs to make sure that the DHCP Server is reachable; if the ADSL Router fails to get the IP Address from DHCP Server, the ADSL Router needs to be rebooted. The router can also be configured as a DHCP client. In this case, the router can broadcast a request to the DHCP Host, for an IP address, subnet mask, and domain name, to be assigned.
5.6 SNMP SNMP is a software entity that responds to information and action request messages sent by a network management station. The messages exchanged enable you to access and manage objects in an active or inactive (stored) MIB on a particular router. To configure the SNMP parameters, click the SNMP button on the Advanced menu bar. The window displays the SNMP parameters.
5.6.1 Modifying SNMP Parameters To modify the SNMP parameters, click the Modify button at the bottom of the screen. Click Apply to submit the settings. To configure the SNMP agent, click the Configure SNMP Agent button. After filling out the fields, click Apply to submit the settings.
5.6.2 Modifying Traps Click the Traps tab to configure the traps. After filling out the parameters, click Submit to apply the settings.
5.6.3 Modifying Communities Click the Communities tab to display the community entry. After filling out the parameters, click Submit to apply the settings. There is no community set up by factory default. To add or modify an entry, click the Configure Community button. To delete an entry, tick the entry and click the Delete button. The following screen displays after clicking the Configure Community button. Enter the parameters and ten click the Apply button.
5.7 Firewall The ADSL router provides packet filtering and stateful packet inspection. It has denial of service protection against attacks such as ICMP Flood, Ping of Death, IP spoofing, Port Scans, Land Attack, Tear Drop Attack, IP Source Route and WinNuke Attack. To access the firewall functions, select Firewall from the advanced menu. The screen will display as below, showing a list of the currently configured filter entries.
5.7.1 Enable/Disable the Firewall To enable the firewall click on the Enable/Disable tab on the Firewall screen and then check the Firewall Enable box and click the Apply button. Conversely, to disable the firewall uncheck the Firewall Enable box and click the Apply button.
5.7.2 Remote Access For each Remote Management Method that you wish to allow on the WAN port, select the method ticking its check box, and then click the Apply button to submit the setting. This function will in effect set up a Port Range mapping – and a Mapping entry will be created. (See section 5.8.2 for details about Port Range Mapping).
5.7.3 View Firewall Actions Click View Actions to display the list of currently configured firewall actions. The parameters are as follows: Action ID: Item number Interface: The interface the filtering rule is created on. Direction: The direction can be IN – only packets received are affected. OUT –only packets sent are affected or ANY –both packets sent and received are affected. Firewall Action: The action taken when packets are received that correspond to a filtering rule.
Firewall Parameters Existing Action ID: If an action has already been established, check the box next to Existing Action ID and enter its Action ID. New Action: If a new action is required check the box next to New Action and then enter: Interface Name –the interface the action applies to, FW Action: Enter Allow, to enable packets to pass through the router, Deny to drop corresponding packets, Reject to reject packet with a response, e.g., sending a TCP reset, or Reset to reject a packet with a reset flag.
5.8 NAT The NAT menu in the Advanced menu bar allows setting up the Static NAT Mapping and Port Range Mapping. 5.8.1 Static NAT Mapping Static NAT Mapping allows a pool of local IP addresses to share a public IP address. It is a form of NAT that maps multiple Private IP addresses to a single Public IP address. It allows several virtually addressed workstations to share a single global address. PAT uses the TCP and UDP port numbers to map multiple virtual addresses to a single global address.
5.8.2 Port Range Mapping The Port Range Mapping is used to set up the virtual server. A virtual server has two access ports: public and private. The public port is the open port where the Internet users access the virtual server. The local port is the port on the LAN that the virtual server is really accessed. The public port is translated to the local port to access to the virtual server. Follow the steps below to configure the Static NAT Mapping: STEP 1: Click the Port Range Mapping tab on the NAT menu.
Fill out the following fields and click Apply to submit the settings. Public Address This is the public address where Internet users access. Enter a specific IP address, or enter 0.0.0.0 to allow any IP Address (if you wish to use the NAT interface address enter 0.0.0.0). Note: if you use 0.0.0.0 as the public address and the NAT interface is not active (interface is not linked-up or not configured) NONE on public address field. It means there is not any active NAT interface to do the PortMaping.
5.9 Configure From this page, you can configure the interfaces, VCC, PPPoE, PPPoA, DNS & Default Gateway, and NAT.
5.9.1 Configure Interface To configure an interface, select it by clicking in the round-box on the left in the screen. Then click on the Configure Interface button at the bottom of the screen. Note the following: Interfaces: eth0 displays the LAN interface. mer0 displays the interface configured for MER mode. wlan0 displays the wireless LAN interface. lo0 is the loopback interface, which is used for management. The default IP address of this interface is 127.0.0.1.
The following is the screen shot for the LAN interface (eth0) after choosing eth0 and clicking the Configure Interface button. The following is a screen shot for the ATM interface.
5.9.2 DNS & Default Gateway To configure the DNS and default gateway, complete the following steps: STEP 1: Click on Configure in the menu bar. STEP 2: Click on DNS and default gateway at the bottom of the configuration page. STEP 3: Complete the fields below: Domain Name: user-defined Primary DNS server: Enter the primary server IP address.
5.9.3 NAT The screen below is accessed by clicking the NAT button on the Configuration screen. To enable NAT check the Enable NAT box and the select the interface that you wish to enable NAT on. 1. From the configuration menu click on the NAT button at the bottom-right side of the screen. 2. Check the Enable NAT box 3. Select the interface to enable NAT 4.
5.10 VCC This screen lists all current VCC entries in the middle of the screen. From this screen you can also: List IPoA, Delete Encapsulation, Add a VCC, Delete a VCC, and Show VCC quality. 5.10.1 List IPoA To list IP over ATM information click on the IPoA button at the bottom-left of the screen.
The IPoA entry is set up from Advanced>Configure>VCC, Click the Add button on the List of VCC screen. 5.10.2 Delete Encapsulation To delete encapsulation first select a VCC entry and then click the Delete Encap button.
5.10.3 Add a VCC To add a VCC entry, complete the following steps: STEP 1: Click on the Add VCC button, the VCC screen will appear. STEP 2: Enter values for the parameters (explained below). STEP 3: Click the Apply button at the bottom of the page. vpi: vci: Peak Cell rate (cells/sec): Average Cell rate (cells/sec): Burst size (cells): CDVT (cells): Type: Service Type: Virtual Path Identifier (VPI) that identifies this ATM connection. The vpi is integer numbers, which can range from 0 to 4095.
5.10.4 Delete a VCC To delete a VCC entry, select the entry from the list of VCCs and then click on the delete button, at the bottom-right of the page. 5.10.5 Show VCC quality To view information regarding the VCC quality, click on the Show VCC Quality button, at the bottom-right of the page. 5.10.6 PPPoE This section will describe how to start, stop, delete, and set a default PPPoE entry. The PPPoE page can be accessed by clicking on Configure in the Advanced menu bar.
5.11 PPPoA This section will describe how to start, stop, delete, and set a default PPPoA entry. The PPPoA page can be accessed by clicking on Configure in the Advanced menu bar. To start, stop, delete, or set as default a PPPoA entry first select the entry from the List of PPPoA entries, and then click the corresponding button at the bottom of the page. 5.
5.12.1 Add an IGMP entry To add an IGMP proxy, complete the following steps: STEP 1: Select IGMP Proxy, from the menu bar. STEP 2: Click Add at the bottom of the screen. STEP 3: Select Proxy interface, router interface, or both, by checking the box next to the interface and then use the pull-down menu to the left to select the eth, atm, or ppp Interface. STEP 4: Click Apply to activate the parameters. 5.12.2 Delete an IGMP entry To delete an entry, select an entry from the list, and click Delete.
5.13 Bridging 5.13.1 Bridge The Bridge window displays the configured Bridging PVC entries of the interfaces. There are four buttons at the bottom of the main-pane: Group Info, Add PVC, Flush, and Disable. ARP Proxy: You can enable the ARP Proxy function by ticking its check box and clicking the Set button. Proxy ARP allows a router to answer a local ARP request for a remote destination.
GroupInfo: This configures the LAN packets that will travel through the LAN interface to the selected WAN interfaces. If you wish to change the interfaces that are configured you must first click on the Flush button (to remove the current configuration), and then click on the Group Info button, select the group interfaces and then click the Apply button. You must select eth0, as eth1 is not enabled for this product version. AddPVC: You can add a PVC to the ATM interface.
5.13.2 Spanning tree To access the spanning tree menu click the Spanning Tree tab, located at the top of the Bridging screen. 5.13.2.1. View STP Parameters To view the STP parameters, click the STP parameters tab, located at the bottom of the Spanning Tree screen.
5.13.2.2. To configure STP parameters STEP 1: Click the Spanning Tree tab, located at the top of the Bridging screen. STEP 2: Click the Configure Port button. STEP 3: Configure the parameters. STEP 4: Click the Apply button. 5.13.2.3. Enable/Disable STP If you wish to Enable/Disable a STP entry, select the entry and then click the Enable or Disable Button, which is located at the bottom-right of the Spanning Tree screen. Note that if the entry is already enabled the Disable button will be present.
5.13.3 Filters Filtering is a type of firewall that is useful to increase network security or to limit unwanted traffic. Filters for this device are based on MAC addresses. The page opens with a list of the currently configured filter entries. From this page, you can also view Filter Parameters, add a filter, delete a filter, modify a filter, or flush filter parameters. These functions are described below. 5.13.3.1.
5.13.3.2. Add a filter entry To add a filtering entry, complete the following steps: STEP 1: Click the Add button at the bottom of the Filters page. STEP 2: Enter the MAC address STEP 3: Set the Frame to forward to forward packets which match the MAC address, or Drop, to drop matching packets. STEP 4: Click Apply. 5.13.3.3. Delete a filter entry To delete a filtering entry Select an entry and then click the Delete button at the bottom of the Filters page. 5.13.3.4.
5.13.4 Layer 2 bridge filtering L2 Filters for this device are based on MAC addresses. The page opens with a list of the currently configured L2 bridge filter entries. Packets are dropped or accepted according to the conditions set up in each entry. From this page, you can also view Filter Parameters, add a filter, or delete a filter. These functions are described below.
5.13.4.1. Enable/Disable L2 filtering If you wish to Enable/Disable Bridge L2 filtering, click Enable or Disable and click the Set button. This setting applies to the list of layer 2 bridge filtering entries. 5.13.4.2. Add a Bridge L2 filter entry To add an L2 filtering entry, complete the following steps: STEP 1: Complete the parameters on the screen: Priority: Enter a priority value from 0-19. The lower the priority value, the higher the entry’s priority.
Chapter 6 6.1 Web Performance monitoring ADSL Link Status To view the ADSL link status, click Link Status on the tool bar. ADSL Line Status Shows the current status of the ADSL line ADSL Mode Shows the ADSL standard that is currently configured. The standards are: ANSI, G.DMT, G.LITE, MULTI. Upstream Upstream data rate negotiated by DSL link (Kbit/s) Downstream Downstream data rate negotiated by DSL link (Kbit/s) Attenuation Current attenuation (dB).
6.2 System Statistics To view the system statistics, click on the System Statistics button located near the bottom of the menu-bar. Statistics are recorded regarding Interfaces, TCP-IP, and DHCP-Lease. 6.2.1 Interface Statistics To display the interface statistics, click the Interface tab, located at the top-left of the System Statistics screen. The Interface Statistics page displays statistics for all interfaces.
6.2.2 TCP-IP To view TCP-IP statistics click on the TCP-IP tab at the top of the System Statistics page. The TCP-IP page displays the IP statistics, UDP statistics, TCP statistics, and ICMP statistics. 6.2.3 DHCP-Lease To view DHCP-Lease statistics click on the DHCP-Lease tab at the top of the System Statistics page. The DHCP-Lease page shows the PCs that obtained an IP address from the DHCP pool.
6.3 Firewall Statistics To view the firewall traffic statistics, click Firewall Statistics from the Advanced menu. It records the session information, including TCP, UDP, ICMP, GRE, AH, and ESP. Each session protocol is represented by a number. For example, 1 is for ICMP, GRE for 47; ESP for 50, AH for 51, UDP for 17, TCP for 6. Each session covers the following information.
6.4 ATM Statistics Click on ATM Statistics on the menu-bar to display the ATM Statistics. The ATM Statistics page monitors information for AAL5 and Encapsulation. 6.4.1 AAL5 The AAL5 page shows the AAL5 statistics. 6.4.2 Encapsulation Click on the SNDCP tab to display encapsulation statistics. This page displays the VCs that are running. (SNDCP stands for sub-network dependency convergency protocol).
Chapter 7 Web Diagnostics To access the Diagnostics screen, click the Diagnostics button, which is located on the menu bar. The Diagnostics screen has two test functions: OAM Loopback and Ping test. 7.1 OAM Loopback STEP 1: Click the Diagnostics button, on the menu bar. STEP 2: Click the Loopback tab on the Diagnostics screen. STEP 3: Enter the following information to run the OAM loopback: Flow type: F5 SEG (Segment to Segment) and F5 ETE (End-to-End). The SEG loopback is from ATUR to DSLAM.
7.2 Ping A Ping test is used to verify the status of a network connection after the RIP or static route function is enabled. Ping sends a request message to the host and waits for a return message. This diagnostic function can verify if the remote host is reachable. Ping can also measure the round-trip time to the remote host. To access the Ping test screen, click the Ping tab on the Diagnostics screen.
Chapter 8 Firmware Upgrade Follow the steps below to upgrade the firmware version of the wireless router via the FTP: STEP 1: Connect the Router to a PC using the LAN cable. Set the PC to the same subnet as the router (192.168.1.x/24). STEP 2: Restore the default parameters of the wireless router by holding down the device’s Reset button until the WLAN LED starts blinking (about 5 seconds).
STEP 8: After you see the message Type set to I, type: hash STEP 9: After you see the message Hash mark printing, type: put app.1 (if the file name has extension, also type the extension. Example: put eagle.ct app.1 STEP 10: After a moment, the file should begin transferring. After you see the message Transfer complete, reboot the ADSL router to complete the upgrade process.
Appendix A: Specifications Wireless Card Standard Encryption Channels Data Rate RF Frequency Wireless Antenna IEEE802.11b 64, 128-bit Wired Equivalent Privacy (WEP) Data Encryption 11 Channels (US, Canada) 13 Channels (Europe) 14 Channels (Japan) 11Mbps / 5.
Routing Functions Routing NAT/PAT Security Authentication protocols VPN features Static route, RIP, and RIPv2 Yes PAP, CHAP, MS-CHAP PPTP/L2TP pass through Power Supply 100, or 220 VAC Dimensions 205 * 145 * 48 mm Specifications are subject to change without notice 91
Appendix B: Pin Assignments Pin Definitions of the LAN port Pin number Definition Pin number Definition 1 Transmit data+ 5 NC 2 Transmit data- 6 Receive data- 3 Receive data+ 7 NC 4 NC NC 8 Note: NC means No connection Pin Assignments of RJ11 Port Pin Definition Pin Definition 1 - 4 TIP 2 - 5 - 3 RING 6 - Note: NC means No connection Console cable DB9 End Pins COLOR RJ-45 End Pins N/C WHITE/ORANGE P1 N/C ORANGE P2 P3 (RD) WHITE/GREEN P3 P2 (TD) BLUE P4 N/C
