™ ™ Service Centers Conair Corporation, Service Department, 150 Milford Road, East Windsor, NJ 08520 Conair Corporation, Service Department, 7475 N. Glen Harbor Blvd, Glendale, AZ 85307 For information on any Conair products call: 1-800-3-CONAIR or visit us on the web at http://www.conair.
CONTENTS Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Getting to Know Your Steam Press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Important / Filling Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
04. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. Do not attempt to repair the appliance. Incorrect reassembly or repair could cause a risk of fire, electric shock, or injury to persons when the appliance is used. Return the appliance to an authorized service center for examination and repair. 05. Keep the cord away from heated surfaces. Do not allow cord to contact heated surfaces.
GETTING TO KNOW YOUR STEAM PRESS 9 6 4 2. The pressing plate is the temperature-controlled surface that heats and presses the fabric. 5 7. The temperature control dial. 8. Water tank. 9. Pressing plate lock. Page 4 07PC2250 FSP5 rev IB.indd Fig. 1 3. Fill the water tank using distilled water. 7 To fill: Remove the water tank. Using a filling container (not included) (Fig. 1), pour water into the tank. Replace by sliding tank back in. Make sure the tank is securely placed before use.
STEAMING TIPS Shirts and Blouses (Fig. 6) 1. Place the shoulder yoke on the ironing board first and press. Pressing Garments 1. Lay the garment on the ironing board. 2. Then place the sleeves on the ironing board with the fold parallel to the long seam and press. 2. Lower the pressing plate and return to the open position after a few seconds. 3. Place the cuffs on the end of the board and press. Wrinkle Removal 4.
CLEANING THE STEAM PRESS TROUBLESHOOTING 1. Unplug and allow the pressing plate to cool. Before taking the unit to a service center, please check the following list of common problems. 2. Clean the plate with a damp cloth. 3. Use of abrasives may damage the plate. Problem Cause Solution 4. The ironing board cover is removable for cleaning. Hand wash only with mild detergent.
™ ™ Centros de Servicio: Conair Corporation, Service Department, 150 Milford Road, East Windsor, NJ 08520 Conair Corporation, Service Department, 7475 N. Glen Harbor Blvd., Glendale, AZ 85307 Para más información sobre los productos de Conair, llame al 1-800-3-CONAIR o visítenos en la Web en http://www.conair.com ©2005 Conair Corporation, East Windsor, NJ 08520, Glendale, AZ 85307 07PC2250 FSP5 rev IB.
MEDIDAS DE SEGURIDAD IMPORTANTES ÍNDICE Medidas de seguridad importantes.........................................................1-3 Aprenda a conocer su prensa a vapor ..............................................…...4 Instrucciones de llenado............................................................................5 Instrucciones de uso..................................................................................
4. Nunca utilice el aparato si el cable o el enchufe están dañados, si no funciona correctamente, si ha caído, si está dañado o si ha caído al agua. Llévelo a un centro de servicio autorizado para que lo examinen y lo reparen. 17. Las partes de metal calientes, el vapor y el agua caliente pueden provocar quemaduras. Por lo tanto, remueva el tanque de agua cuidadosamente. No voltee el aparato, puesto que el tanque puede contener agua caliente. 5. Mantenga el cable alejado de las superficies calientes.
APRENDA A CONOCER SU PRENSA A VAPOR 1. Empuñadura para subir y bajar la prensa y para producir vapor. 2. Prensa con temperatura controlada. 3. Superficie de prensado acolchada, amovible y lavable a mano. 4. Indicador luminoso de encendido. Se ilumina cando la prensa esté encendida. 5. Interruptor de encendido/apagado. 6. Indicador luminoso de listo. Se ilumina cando la prensa llega a la temperatura deseada. 7. Ajuste de temperatura. 8. Tanque de agua. 9. Bloqueo 9 6 4 Para uso doméstico únicamente.
CONSEJOS PARA EL PRENSADO Camisas y Blusas (Fig. 6) 1. Empiece por prensar la cumbre del hombro. Prensar 1. Acomode la ropa sobre la superficie de prensado. 2. Baje la prensa, espere unos segundos, luego suba la prensa. Desarrugar 1. Baje la prensa (sin tocar la tela) hasta que el vapor salga. IMPORTANTE: Se puede que necesite apretar la empuñadura 2. Acomode las mangas de largo en la superficie de prensado y prense. 3. Prense los puños. 4.
INSTRUCCIONES DE LIMPIEZA RESOLUCIÓN DE PROBLEMAS 1. Desconecte el aparato y déjelo enfriar. Antes de llevar el aparato a un centro de servicio, consulte la guía de resolución de problemas siguiente. Problema Posible Causa Solución 2. Limpie la prensa con un paño húmedo. 3. No use limpiadores abrasivos. Esto podría lastimar la prensa. 4. La superficie acolchada de prensado es amovible y lavable a mano. Use detergentes suaves para lavado a mano. INSTRUCCIONES DE ALMACENAMIENTO 1.