Product Manual

ManualsBrandsConcentric ManualsElectric ActuatorsGlideforce 225-Lb. Capacity Linear Actuator by — 8in. Medium-Duty, 7.87in. Stroke

Concentric International

1901 Bell Ave., Suite 18, Des Moines, IA 50315

www.concentricintl.com

Rev. 20160824

Page 1 of 5

LINEAR ACTUATOR

MEDIUM DUTY SERIES

Product Data Sheet

Standard Features:

 Compact design

 All aluminum frame and extension tube

 Nominal stroke lengths: 4” [100mm], 6” [150mm], 8” [200mm], 10” [250mm],

12” [300mm]

 Input voltage: 12VDC, 24VDC

 Standard gear ratio: 20:1 [other ratios available]

 Load range: 112 lbs. [500 Newtons] –to- 562 lbs. [2500 Newtons]

 Maximum current draw: 4.6 Amps @ 12 VDC

 Inrush current at maximum load: 6 amp @ 12 VDC, 3 amp @ 24 VDC

 Speed at no load: 0.24 in/sec [6.2 mm/sec] –to- 1.06 in/sec [26.8 mm/sec]

 Speed at full load: 0.17 in/sec [4.4 mm/sec] –to- 0.73 in/sec [18.6 mm/sec]

 Standard preset limit switches at both ends of stroke

 Mounting hole diameter (both ends): 3/8” [10mm]

 Duty cycle: 25% or 1 min continuous operation in 4 min.

 Working temperature: -13F [-25C] +149F [+65C]

 IP rating: IP65

Accessories:

 Mounting brackets

 Direction reversing wireless controller

 Direction reversing relays

 Direction reversing switches

Summary of content (5 pages)

PAGE 1
LINEAR ACTUATOR MEDIUM DUTY SERIES Product Data Sheet Standard Features:                Compact design All aluminum frame and extension t ube Nominal stroke lengths: 4” [100mm], 6” [150mm], 8” [200mm], 10” [250mm], 12” [300mm] Input voltage: 12VDC, 24VDC Standard gear ratio: 20:1 [other ratios available] Load range: 112 lbs. [500 Newtons] –to- 562 lbs. [2500 Newtons] Maximum current draw: 4.6 Amps @ 12 VDC Inrush current at maximum load: 6 amp @ 12 VDC, 3 amp @ 24 VDC Speed at no load: 0.
PAGE 2
LINEAR ACTUATOR MEDIUM DUTY SERIES Dimensions (Standard Actuator) Nominal Stroke Actual Stroke Retracted Length (A) Extended Length (B) 4” 6” 8” 10” 12” in mm in mm in mm in mm in mm 3.94 100 5.91 150 7.87 200 9.84 250 11.81 300 8.07 205 10.04 255 12.01 305 13.98 355 15.94 405 12.01 305 15.94 405 19.88 505 23.82 605 27.76 705 Concentric International 1901 Bell Ave., Suite 18, Des Moines, IA 50315 www.concentricintl.com Rev.
PAGE 3
LINEAR ACTUATOR MEDIUM DUTY SERIES Performance Data Gear Ratio Max Load/Dynamic Speed/No Load Speed/Max Load 10:1 20:1 30:1 40:1 Lbs. [US] 112 225 337 450 Newtons 500 1000 1500 2000 inches/Sec 1.06 0.58 0.39 0.29 mm/Sec 26.8 14.7 9.9 7.4 inches/Sec 0.73 0.41 0.27 0.20 mm/Sec 18.6 10.4 6.8 5.1 50:1 562 2500 0.24 6.2 0.17 4.4 Concentric International 1901 Bell Ave., Suite 18, Des Moines, IA 50315 www.concentricintl.com Rev.
PAGE 4
LINEAR ACTUATOR MEDIUM DUTY SERIES Electrical Red + // Black - : Extend Red - // Black + : Retract 25 ma. maximum sink current W ire Color Pin Dual Hall Sensor W ithout Hall Sensor A B Red (M+) Black (M-) C W hite (GND) D Blue (Data 1) E Yellow (VCC) F Green (Data 2) ----- ----- ----- ----- Resolution of Hall Sensor Gear Ratio Signal Resolution 10 20 30 Pulses/in 0.10 0.19 0.28 Pluses/mm 2.56 4.75 7.16 40 50 0.38 0.47 9.66 11.82 Concentric International 1901 Bell Ave.
PAGE 5
LINEAR ACTUATOR MEDIUM DUTY SERIES Ordering Key MD Input Voltage 12 : 12 VDC 24 : 24 VDC Gear Ratio 10 : 10:1 20 : 20:1 – Standard gear ratio 30 : 30:1 40 : 40:1 50 : 50:1 Not all gear ratios stocked Stroke (nominal) 04 : 4” [100 mm] 06 : 6” [150 mm] 08 : 8” [200 mm] 10 : 10” [250 mm] 12 : 12” [300 mm] Additional stroke lengths available Option Blank : Without Hall Sensor H2 : Dual Hall Sensor Terms of Use The user is responsible for determining the suitability of Concentric International products for sp