BOOKCASE 36" Model No. Mi4836To ensure that you have a speedy and pleasant time assembling your unit PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE BEGINNING ASSEMBLY. | If you need assistance, DO NOT CALL THE STORE, call us. Our Customer Service Group is here to | help you. CALL MONDAY-FRIDAY, BETWEEN 8:00AM TO 3:00PM PACIFIC TIME. Please be sure to follow the construction order in the Assembly Manual and complete each step before you proceed to the next step. Call: USA Ply craft Industries Inc. 2100 E.
PARTS a) Top {1 pe.) UNFINISHED b} Bottom (1 pe.) } Adjustable Shelves (4 cps) [op ¢) Side Moldings (2 cps) d) Left Side (1 pc.) e) Right Side (1 pc.) g) Divider (1 pe.) HARDWARE == I) Wood Dowel 1 (18 pea) p) Back Panel Washer (2 pea) ©) — m) Cam lock {21 cps) q) Back Panel Screw 5/8" (27 pea) mw 8 Perm n) Metal Fastener (21 cps) 1) Flat Head Screw 1 1/4” (9 cps) J 0) Shelf Support (16 cps) h} Top Apron {1 pc.) i) Bottom Apron (1 po.) SMALLER MOLDING j) Divider Molding (1 pc.
step 4 Insert 6-Wood Dowels (1) into each Side Panel holes. See diagram above. Insert and screw 4-Metal Fasteners {n} into each Side Panel. I See Diagram above.
Step 3 Step 4 LABEL : THIS SIDE UP, Page 4 Insert and screw 3-Metal Fasteners (n) into each Side Molding (c). See Diagram above. DO NOT OVER TIGHTEN Insert and screw 3-Metal Fasteners (n) into Divider Molding (f). See Diagram above.
Step 5 Be sure the edge of the side molding is flush with the outside panel (no holes). Insert 6-Cam Locks {m) into the large prevailed holes ( 3 per each side), point the arrow on the Cam in the direction of the side edge. Push the Cam into the hole. Then use a screwdriver, to turn each Cam approximately 1/2 turn in the direction of the arrow (clock-wise) fo lock it in place. See Diagram above.
insert 3-Wood Dowels (1) into Bottom (b) and 3-Wood Dowels (1} into Top (a). | See diagram above. Step 8 Insert and screw 2-Neal Fastener (n) into top and bottom panels. See Diagram above.
Tor Attach Top (a) and Bottom (b) wi Divider Panel attached facing down as showing. Soft surface Step 10 Attach Left Side and Right Side attached to the previous sub assembly as shown. Be sure all wood dowels and metal fasteners are located in the apposite holes BEFORE insert the cam locks. Or m) insert 4-Cam Locks (my) info the large prevailed holes, point the arrow on the Cam in the direction of the side edge. Push the Cam into the hole.
lift the top of the Bookcase and slide Top Apron underneath. Make Install Top Apron (h) to the Top and Bottom Apron {i) to the Bottom with Flat screws (r), press down firmly and carefully to close all gaps. See Diagram above. IMPORTANT: Back Panel must be completely aligned with TOP and side edges as well, to ensure a square cabinet . Bottom Apr sure the cleats are inside the top. Step 12 DO NOT REMOVE TAPE NOTE: DO NOT LIFT OR TILT ON SIDE OR EDGES.
Finally screw 2 Screws (q) with washer (p) along the tape, as shown in step 13. DG NOT REMOVE TAPE See the diagram above. NOTE: DO NOT LIFT OR TILT ON SIDE OR EDGES. DO NOT LIFT UP THE STORAGE CABINET UNTIL BACK PANEL IS INSTALLED, Step Insert Shelves Support {0} into Side holes in the position you decided then place the Adjustable Shelves {f). See Diagram above.
SECURED TO J, WITH SCREW (1) / N=" 5£CURED TO TOP OF BOOKCASE WITH SCREW (a) Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended. This hardware when properly installed, could provide protection against the unexpected tipping of furniture due to improper use. WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Installation Instructions: 1.