Technical Specifications

Conco® P801 Interior/Exterior Flat Acrylic Prime & Finish is an industrial grade coating designed for new construction
and maintenance applications. Conco P801 provides excellent adhesion to hard, glossy, slick surfaces while resisting
flash rust, corrosion, and chemicals. This product’s performance is perfect for machinery, equipment, piping and
more, giving you a great start to your commercial paint project.
P801 PRIME & FINISH
INDUSTRIAL GRADE
INTERIOR/EXTERIOR FLAT
WHITE
FEATURES
• Industrial grade coating designed for new construction and
maintenance applications
• Ideal for ferrous and galvanized metal, aluminum, masonry,
pl
aster, aggregate block, PVC, fiberglass, and previously
painted surfaces
• Provides outstanding adhesion
• Chemical resistant
• Flash rust and corrosion resistant
• Easily applied using a brush, roller, or airless sprayer
• Soap and water cleanup
• Backed by a 100% Satisfaction Assured Warranty
TECHNICAL DATA
Vehicle: Acrylic
Finish: N/A
Flash Point: N/A
Weight Solids: 61% ± 2%
Volume Solids: 47% ± 2%
Dry Time (@ 77°F and 50% R.H.)
To Touch: 1 Hour
To Recoat: 4 Hours
Weight Per Gallon: 11.45 lb/gal
VOC: <50 g/L – 0.42 lb/gal
as per 40 CFR 59.406
Spread Rate: 150-300 sq.ft. per gallon
(dependent on surface texture and porosity)
Film Thickness: @ 4 mils wet; 1.4 mils dry
Sizes: Gallons, Fives
APPLICATION
RECOMMENDED SYSTEMS
Do not apply at air, surface or product temperatures below 50°F
or when air or surface temperatures may drop below 50°F within
24 hours.
Spray – Airless
Pressure 2000 psi
Tip .015” - .019”
May be thinned up to 1/2 pint of water per gallon of paint spray
application.
Brush
Use a quality nylon/polyester brush.
Roller
Use a 3/8” nap synthetic roller cover.
Ferrous Metal, Galvanized Metal and Aluminum
2 coats Conco P801 DTM Acrylic Prime & Finish
or
1 coat Conco P801 DTM Acrylic Prime & Finish
1 or 2 coats Conco 8000 Series DTM Acrylic Gloss Industrial Enamel
Masonry & Plaster (allow to cure for 30 days)
2 coats Conco P801 DTM Acrylic Prime & Finish
or
1 coat Conco P801 DTM Acrylic Prime & Finish
1 or 2 coats Conco 8000 Series DTM Acrylic Gloss Industrial Enamel
Aggregate Block
1 coat Conco P9511 Interior/Exterior Acrylic Latex Block Filler
1 or 2 coats Conco P801 DTM Acrylic Prime & Finish
Previously Painted Surfaces
1 or 2 coats Conco P801 DTM Acrylic Prime & Finish
PVC, Fiberglass
2 coats Conco P801 DTM Acrylic Prime & Finish
or
1 coat Conco P801 DTM Acrylic Prime & Finish
1 or 2 coats Conco 8000 series DTM Acrylic Gloss Industrial Enamel
TIPS FOR BETTER PERFORMANCE
• To ensure maximum protection, stripe coat all crevices, welds
and sharp angles
• For best results over rusty surfaces, apply the first coat by
br
ush
• During s
pray application, overlap 50% with each pass of the
spray gun to avoid bare areas, pinholes and holidays
• Avoid r
ain, dew, high humidity and moisture condensation
during the 16-24 hours after application, as the film will be
sensitive
• The s
pread rates are calculated by the volume solids and do
not take into consideration product loss caused by applicator
technique, method of application, surface irregularities, over
thinning and climatic conditions
• Excessive r
eduction can affect hide, film build, appearance,
abrasion resistance and adhesion
• Application t
emperature below 55° F could cause adhesion,
drying and curing issues
• Application a
bove 95° F could result in poor adhesion, dry
spray and uneven sheen
• Conco P
801 DTM Acrylic Prime & Finish is sensitive to
hydrocarbon containing solvents. When cleaning the surface
per SSPC-SP1, use only emulsifying detergents and degreasers
followed by a water rinse
• DO NO
T USE HYDROCARBON SOLVENTS FOR CLEANING
APPLICATION