® California Collection ™ 52CT Owners Manual and Installation Instructions Part Number: PL-3210 (Revised 03.10.
READ AND SAVE THESE INSTRUCTIONS Before beginning installation of your new Concord® ceiling fan, read and follow these safety precautions. If you are not familiar with national and local electrical codes and basic electrical wiring procedures, we recommend that you have a qualified electrician install your new ceiling fan. Before you begin, TURN OFF THE ELECTRICITY. Determine which circuit your new fan will be using and remove the fuse or turn off the circuit breaker at the main electrical panel.
This ceiling fan was not designed for installation in any location where it might be exposed to moisture or high humidity. Installation in this type of location could be unsafe, will most likely damage the fan and its finish .....and WILL VOID YOUR WARRANTY. Every effort has been made to provide you with proper instructions for the safe installation of this ceiling fan. You could however, encounter situations or problems not covered in this manual.
Canopy Mounting Screw Have you TURNED OFF the Electricity? Fig. 1 This fan is shipped with 2 downrods. 6” for regular ceiling application and 2” for low ceiling application. Choose the one that fits your need. Junction Box Step 1 Attach the mounting bracket Loosen the two canopy mounting screws on the downside face of the mounting bracket. Back them out about half way. This will allow for easier installation of the ceiling canopy later.
Pull the electric wires in the junction box down through the mounting bracket then bend them up and back out of the way. Place the black wire to one side and the white and ground wire to the other side (see figure 4) The wires should be off to the side and up against the ceiling. This will leave the mounting bracket open and ready to receive the ceiling fan. Step 2 Attach the support assembly Fig.
Mounting Bracket Step 3 Hanging the Fan Body Notice the half ball on the end of the support rod is grooved down one side (see figure 6). This Keyway fits over the small keyway pin on the inside of the mounting bracket and keeps the ceiling fan from spinning on the mounting bracket. Keyway Pin Ball Hanger Support Rod Using your step ladder, lift the fan and place the half ball in the center of the mounting bracket with the keyway pin inserted into the keyway on the ball.
Making the electrical connections To operate your ceiling fan with the pull chain(s) and switches mounted on your fan, follow the instruction below (see figure 9). Green Black Blue If you require or would like to use a different method of controlling your fan, refer to the Optional Electrical Wiring Procedures on page 10. White Attach the GREEN wire (connected to the half ball) to the GROUND wire in the junction box. The GROUND wire is usually a bare copper wire without plastic insulation.
Step 4 Install the ceiling fan If you are using the Flush Mount System, skip this step. Slide the ceiling canopy up into place over the ceiling mounting bracket (see figure 11). The two screws on the mounting bracket face should slip through the key hole slots in the canopy. Rotate the canopy slightly and then tighten both screws. Depending on how deep the electrical junction box was installed in the ceiling, you might have a slight gap between the ceiling canopy and the ceiling.
Step 6 Blade Assembly Installation Remove the large screws in the face of the motor. Discard any rubber blocks attached to these screws. The rubber blocks are installed at the factory to stabilize the motor during shipment. You have the choice of using 4 or 5 blades (see figure 14). 4 or 5 Blade Pattern Select the correct mounting pattern and attach each blade to the motor face using pre-installed screws (see figure 13). Take care not to bend the blade arms during installation.
Step 8 Final Checks Fan controlled with wall switch and Light controlled at fan. Check that all safety pins, set screws and connections are properly in place and tight. Check blade clearance and rotation. Attach the decorative pull chain tassel(s) to the switch housing. Located on the side of the switch housing is a slide switch. This switch controls the direction of blade rotation. The UP position sets the blades in reverse rotation (air moves UP).
Your new ceiling fan is now ready to use. Reset your circuit breaker and restore power to the circuit. See the Operation Instruction below to review the function of each control on your fan. Operation Instructions The pull chain located on the switch housing (see figure 16) controls the speeds of your fan. When the fan is off, pull the chain once for HIGH speed, twice for MEDIUM speed, three times for LOW speed and fourth time to turn it OFF again.
