Technical Specifications
TECHNICAL DATA
CRM-01
CONCROBIUM
®
MOLD CONTROL
®
1
Form: ARJ-1882
Rev.: 072419
DESCRIPTION AND USES
Concrobium
®
Mold Control
®
is an EPA-registered solution
that eliminates and prevents mold without any harmful
chemicals. Mold Control dries to form an invisible
antimicrobial shield that encapsulates and physically crushes
mold spores. The antimicrobial barrier remains on surfaces
to provide continuous protection against mold growth. The
unique technology is used by homeowners, professional
remodelers, contractors and remediates.
The larger 1 gallon jug and 5 gallon pail are ideal for large-
scale jobs like remediating a basement or attic that has
experienced moisture and mold damage. Use the 1 gallon
jug or 5 gallon pail along with our cold-fogger to pre-treat
new building materials against future mold damage quickly
and safely.
PRODUCT FEATURES
Mold remediation in homes, businesses and institutions
Mold prevention following flooding or water damage
cleanup
Pre-treatment of building materials for mold resistance
Mold and mildew treatment while painting
Musty odor control in vulnerable areas
PRODUCTS
SKU
DESCRIPTION
27400
14.1 Oz. Aerosol
25326
32 Oz. Trigger Sprayer Bottle
25001
128 Oz. Jug
25005CC
5 Gallon Pail
COMPANION PRODUCTS
SKU
DESCRIPTION
200620810
Fogger*
200080
Fogger Intake Filter*
*Sold separately. Fogger used for treating larger or hard to
reach areas. Refer to Fogger TDS for application
instructions.
PRODUCT APPLICATION
READ ALL INSTRUCTIONS CAREFULLY BEFORE
STARTING PROJECT
Mold Control is effective against mold and mildew organisms
on both hard and fabric surfaces that have been subjected to
wet environments. If in doubt, test on a small, inconspicuous
section. Wipe materials vulnerable to water marks
immediately after contact with Mold Control. Over-
application may result in residue formation, which can be
wiped away with a Mold Control-dampened cloth.
PRODUCT APPLICATION (cont.)
PERSONAL PROTECTION EQUIPMENT
REQUIREMENTS FOR APPLICATORS
For areas less than 30 square feet, an N-95 respirator,
gloves and goggles/eye protection are recommended to
avoid mold or mold spore exposure. For areas greater than
30 square feet, use an N-95 respirator or half-face respirator
with HEPA filter, disposable overalls, glove and goggles/eye
protection.
NOTE: Mold Control is ready to use - do not dilute. Before
applying, correct conditions favorable to mold growth.
APPLICATION TO ELIMINATE MOLD
SMALL AREAS
(Total Surface Area Affected Less Than 30 Square Feet)
Apply by cloth, hand-spray, electric or compression spray,
cold fogger, paintbrush, roller or immersion.
1. Remove heavy soil (Mold Control must come in direct
contact with mold to be effective).
2. Apply product on area until evenly wet.
3. If desired, wipe off excess wetness.
4. Allow treated surfaces to dry completely.
NOTE: Do not expect Mold Control to whiten stains on
contact. If mold stains remain, reapply product and wipe or
scrub area. In some cases, staining may be irreversible. If
additional steps are taken to remove or cover the stain,
reapply Mold Control as a final step to protect area from
regrowth.
LARGE AREAS
(Total Surface Area Affected Greater Than 30 Square
Feet)
Areas larger than 30 square feet require special procedures
and individuals trained in remediation. Refer to the
recommended websites for guidelines on remediation.
Before using Mold Control to mitigate large areas, you
should understand one or more of these guidelines. Follow
these guidelines to apply Mold Control.
Mold Control must be used as part of a comprehensive mold
remediation or water damage restoration program, including:
Monitoring for conditions favorable to mold growth such
as water leaks and high relative humidity
Eliminating conditions favorable to mold growth
Drying affected areas to below 20% moisture content