Owner manual

ManualsBrandsCondec ManualsEquipmentMPV-10K

March 2001

Toll Free: 888-295-8475 • International: 715-234-9171 • FAX: 715-234-6967

WEB SITE: www.4condec.com

MPV-10K

Micro-Metering Precision Valve

MPV-10K Micro-Metering Precision Valve

Patent No. 4.698.998

Part #57168: MPV-10K with Fluorocarbon “Viton” (standard)

Part #54803: MPV-10K with Nitrile Buna-N O-ring

Part #54906: MPV-10K with Ethylene-propylene

Part #57161: MPV-10K with Silicone

Part #57122: MPV-10K with Neoprene

SPECIAL FEATURES:

• MPV-10K features all stainless steel construction for use with corrosive gases and on

operating pressure from vacuum to 10,000 psi. It consists of one low torque, fine micro-

metering valve with positive shut-off, adjustable stop and soft seat. The valve allows the

operator a very fine fingertip pressure adjustment.

• Selecting the appropriate O-ring material may extend the wide range of gas applications.

OPERATION:

The pressure valve will begin to open when it is turned counter clockwise approximately

15 degrees. Full open position of the valves is achieved with a maximum of 3 1/2 turns

from the closed position. The valve has a fine adjustment sensitivity of .0005 psi. Very low

torque is required to turn the vernier... FINGERTIP ADJUSTMENT!!!!!

SPECIFICATIONS:

• Pressure Range: 0-10,000 psi and vacuum

• Proof Pressure: 15000 psi

• Orifice: .032

• CV: .007

• Mechanical Rotation: 10 turns (nom.)

• Torque: Fingertip adjust

• Volume: 1/2 cubic inch (Nom.)

• Adjustable sensitivity: .0005 psi

• Construction: 303 stainless steel body, black anodized aluminum knob. All other parts 304 series stainless,

O-rings fluorocarbon “Viton” STD, others available.

• Weight: 3.0 lbs.

• O-ring repair kits: Buna-N (part #58499); Ethylene-Propylene (part #58506);

Silicone (part #58509); Neoprene (part #58515); Fluorocarbon “Viton” (standard) (part #55277).

Note: Various O-ring materials may be installed in MPV-10K by special order, but may not be

rated for 10,000 psi

67742

Summary of content (4 pages)

PAGE 1
Micro-Metering Precision Valve MPV-10K MPV-10K Micro-Metering Precision Valve Patent No. 4.698.998 Part #57168: MPV-10K with Fluorocarbon “Viton” (standard) Part #54803: MPV-10K with Nitrile Buna-N O-ring Part #54906: MPV-10K with Ethylene-propylene Part #57161: MPV-10K with Silicone Part #57122: MPV-10K with Neoprene SPECIAL FEATURES: • MPV-10K features all stainless steel construction for use with corrosive gases and on operating pressure from vacuum to 10,000 psi.
PAGE 2
MPV-10K Micro-Metering Precision Valve Patent No. 4.698.998 INSTALLATION: The fine micro-metering valve is factory adjusted. .650 Panel or bracket mounting: .20 1. Turn the knob counter clockwise, remove knob and stop washer. 2. Loosen #4 set screw, remove locknut and panel mounting nut. .593 DIA 3. Install controller into recommended hole pattern with two 8-32 x 3/8" lg. screw. 4. Install panel mounting nut, locknut (all the way to the end), stop washer and knob.
PAGE 3
MPV-10K Micro-metering Precision Valve Bill of Material Ref # 1 ...... 2 ...... 3 ...... 4 ...... 5 ...... 6 ...... 7 ...... 8 ...... 9 ...... 10 .... 11 .... 12 .... 13 .... 14 .... 15 .... 16 .... 17 .... 18 .... 19 .... 20 .... 21 .... 22 .... 23 .... 24 .... 25 .... 26 .... 27 .... Part # Description Qty. 54193 ............ Valve body ......................................................................................................... 1 54540 ............ Housing, Valve Needle .....................
PAGE 4
2 13 11 12 14 16/2X 15 1 8 4 7 5 NOTES: 1 LIGHTLY COAT O-RINGS AND THREADS ON VALVE NEEDLE WITH THE FOLLOWING LUBRICANT, PART NO. 55593. 10 19 18 OR OR 20 23 OR OR 21 24 OR OR 22 25 OR 27 O-RING, .042 ID 9 3 OR 1 6 OR 1 26 O-RING, .