CONFIGURATION MANUAL for v2 routers LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
USED SYMBOLS Used symbols Danger – important notice, which may have an influence on the user’s safety or the function of the device. Attention – notice on possible problems, which can arise in specific cases. Information, notice – information, which contains useful advice or special interest. Firmware version Actual version of firmware is 3.0.7 (12.7.2013). GPL licence Source codes under GPL licence are available free of charge by sending an email to: info@conel.cz.
CONTENTS Contents 1 Configuration over web browser 1 1.1 Secured access to web configuration . . . . . . . . . . . . 1.2 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2.1 Mobile Connection . . . . . . . . . . . . . . . . . . 1.2.2 Primary LAN . . . . . . . . . . . . . . . . . . . . . 1.2.3 Peripheral Ports . . . . . . . . . . . . . . . . . . . 1.2.4 System Information . . . . . . . . . . . . . . . . . . 1.3 Mobile WAN status . . . . . . . . . . . . . . . . . . . . . . 1.
CONTENTS 1.27 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.36 1.37 1.38 1.39 1.40 1.41 USB port configuration . . . . . . Startup script . . . . . . . . . . . Up/Down script . . . . . . . . . . Automatic update configuration . User modules . . . . . . . . . . . Change profile . . . . . . . . . . Change password . . . . . . . . Set real time clock . . . . . . . . Set SMS service center address Unlock SIM card . . . . . . . . . Send SMS . . . . . . . . . . . . Backup configuration . . . . . . .
LIST OF FIGURES List of Figures 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Web configuration . . . . . . . . . . . . . . . . . . . Mobile WAN status . . . . . . . . . . . . . . . . . . . Network status . . . . . . . . . . . . . . . . . . . . . DHCP status . . . . . . . . . . . . . . . . . . . . . . IPsec status . . . . . . . . . . . . . . . . . . . . . . . DynDNS status . . . . . . . . . . . . . . . . . . . . . System Log . . . . . . . .
LIST OF FIGURES 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 PPTP tunnel configuration . . . . . . . . . . . . Topology of example PPTP tunnel configuration Example of DynDNS configuration . . . . . . . Example of NTP configuration . . . . . . . . . . Example of SNMP configuration . . . . . . . . Example of the MIB browser . . . . . . . . . . . SMTP configuration . . . . . . . . . . . . . . . Example of SMS configuration 1 . . . . . . . .
LIST OF TABLES List of Tables 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Mobile connection . . . . . . . . . . . . . . . . . . Peripheral Ports . . . . . . . . . . . . . . . . . . . System Information . . . . . . . . . . . . . . . . . . Mobile Network Information . . . . . . . . . . . . . Description of period . . . . . . . . . . . . . . . . . Mobile Network Statistics . . . . . . . . . . . . . . Traffic statistics . . . . . . . . . . . .
LIST OF TABLES 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Example PPTP tunel configuration . . . . . . DynDNS configuration . . . . . . . . . . . . . NTP configuration . . . . . . . . . . . . . . . SNMP agent configuration . . . . . . . . . . . SNMPv3 configuration . . . . . . . . . . . . . SNMP configuration (MBUS extension) . . . SNMP configuration (R-SeeNet) . . . . . . . Object identifier for binary input and output . Object identifier for CNT port . . . . .
1. CONFIGURATION OVER WEB BROWSER 1. Configuration over web browser Attention! If the SIM card is not inserted in the router, then wireless transmissions will not work. The inserted SIM card must have activated GPRS. Insert the SIM card when the router is switched-off. For monitoring, configuring and managing the router use web interface, which can be invoked by entering the IP address of the router into your browser. The default IP address of the router is 192.168.1.1.
1. CONFIGURATION OVER WEB BROWSER After green LED starts to blink it is possible to restore initial settings of the router by pressing button RST on front panel. If press button RST, configuration is restored to default and it is reboot (green LED will be on). 1.1 Secured access to web configuration To the web configuration can be accessed via a secure HTTPS protocol. In the event of a default router IP address is a secure router configuration accessed by entering address https://192.168.1.
1.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Serial Number Serial number of the router (in case of N/A is not available) Profile Current profile – standard or alternative profiles (profiles are used for example to switch between different modes of operation) Supply Voltage Supply voltage of the router Temperature Temperature in the router Time Current date and time Uptime Time indicating how long the router is used Table 3: System Information 1.
1. CONFIGURATION OVER WEB BROWSER The next section of this window displays information about the quality of the connection in each period.
1. CONFIGURATION OVER WEB BROWSER The last part (Mobile Network Connection Log) informs about the mobile network connection and problems in establishment. Figure 2: Mobile WAN status 1.4 Network status To view system information about the router operation, select the Network item in the main menu.
1.
1. CONFIGURATION OVER WEB BROWSER Figure 3: Network status 1.5 DHCP status Information on the activities of the DHCP server can be accessed by selecting the DHCP status item. DHCP status informs about activities DHCP server. The DHCP server provides automatic configuration of devices connected to the network managed router. DHCP server assigns to each device’s IP address, netmask, default gateway (IP address of router) and DNS server (IP address of router).
1. CONFIGURATION OVER WEB BROWSER Figure 4: DHCP status In the extreme, the DHCP status can display two records for one IP address. That could have been caused by resetting of network cards. 1.6 IPsec status Information on actual IPsec tunnel state can be called up in option IPsec in the menu. After correct build the IPsec tunnel, status display IPsec SA established (highlighted in red) in IPsec status information. Other information is only internal character. Figure 5: IPsec status 1.
1. CONFIGURATION OVER WEB BROWSER In detecting the status of updates DynDNS record are possible following message: • DynDNS client is disabled. • Invalid username or password. • Specified hostname doesn’t exist. • Invalid hostname format. • Hostname exists, but not under specified username. • No update performed yet. • DynDNS record is already up to date. • DynDNS record successfully update. • DNS error encountered. • DynDNS server failure.
1. CONFIGURATION OVER WEB BROWSER Figure 7: System Log Example of logging into the remote daemon at 192.168.2.115: Figure 8: Example program syslogd start with the parameter -r 11 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.9 LAN configuration To enter the network configuration, select the LAN menu item. ETH network set in Primary LAN configuration, expansion PORT ETH set in Secondary LAN configuration. Item Description DHCP Client • disabled – The router does not allow automatic allocation IP address from a DHCP server in LAN network. • enabled – The router allows automatic allocation IP address from a DHCP server in LAN network.
1. CONFIGURATION OVER WEB BROWSER Item Description Enable dynamic DHCP leases If this option is checked, dynamic DHCP server is enable. IP Pool Start Start IP addresses space to be allocated to the DHCP clients. IP Pool End End IP addresses space to be allocated to the DHCP clients. Lease time Time in seconds, after which the client can use IP address.
1. CONFIGURATION OVER WEB BROWSER Figure 10: Example LAN configuration 1 Example of the network interface with dynamic and static DHCP server: • The range of allocated addresses from 192.168.1.2 to 192.168.1.4. • The address is allocated 10 minutes. • Client’s with MAC address 01:23:45:67:89:ab has IP address 192.168.1.10. • Client’s with MAC address 01:54:68:18:ba:7e has IP address 192.168.1.11. 14 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.
1. CONFIGURATION OVER WEB BROWSER Figure 11: Topology of example LAN configuration 2 Figure 12: Example LAN configuration 2 15 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER Example of the network interface with default gateway and DNS server: • Default gateway IP address is 192.168.1.20 • DNS server IP address is 192.168.1.20 Figure 13: Topology of example LAN configuration 3 Figure 14: Example LAN configuration 3 16 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.10 VRRP configuration To enter the VRRP configuration select the VRRP menu item. VRRP protocol (Virtual Router Redundancy Protocol) is a technique, by which it is possible to forward routing from main router to backup router in the case of the main router failure. If the Enable VRRP is checked, then it is possible to set the following parameters. Item Description Virtual Server IP Address This parameter sets virtual server IP address.
1. CONFIGURATION OVER WEB BROWSER If Ping Timeout expires with no answer received then process of testing the active line continues the same way like in the case of standard testing process after first test message answer drops out. Example of the VRRP protocol: Figure 15: Topology of example VRRP configuration Figure 16: Example VRRP configuration — main router Figure 17: Example VRRP configuration -– backup router 18 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax.
1. CONFIGURATION OVER WEB BROWSER 1.11 Mobile WAN configuration This item is not available for industrial router XR5i v2. The form for configuration of a connection to the mobile network can be invoked by selecting the Mobile WAN item in the main menu of the router web interface. 1.11.1 Connection to mobile network If the Create connection to mobile network item is selected, the router automatically tries to establish connection after switching-on.
1. CONFIGURATION OVER WEB BROWSER Tips for working with the Mobile WAN configuration form: • If the IP address field is not filled in, the operator automatically assigns the IP address when it is establishing the connection. If filled IP address supplied by the operator, router accelerate access to the network. • If the APN field is not filled in, the router automatically selects the APN by the IMSI code of the SIM card.
1. CONFIGURATION OVER WEB BROWSER If the Enable Traffic Monitoring option is selected, then the router stops sending ping questions to the Ping IP Address and it will watch traffic in connection to mobile network. If this connection is without traffic longer than the Ping Interval, then the router sends ping questions to the Ping IP Address. Attention! We recommend checking the Check connection to mobile network in case of uninterrupted running. 1.11.
1. CONFIGURATION OVER WEB BROWSER If parameter Backup SIM card is set to none, then parameters Switch to other SIM card when connection fails, Switch to backup SIM card when roaming is detected and switch to default SIM card when home network is detected and Switch to backup SIM card when data limit is exceeded and switch to default SIM card when data limit isn’t exceeded switch the router to off-line mode.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Subsequent Timeout In an unsuccessful attempt to switch to default SIM card, the router on the second attempt to try for the time defined in the parameter Subsequent Timeout, range is from 1 to 10000 min.
1. CONFIGURATION OVER WEB BROWSER Figure 18: Mobile WAN configuration 24 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER The figure below describes the situation, when the connection to mobile network is controlled on the address 8.8.8.8 in the time interval of 60 s for primary SIM card and on the address www.google.com in the time interval 80 s for secondary SIM card. In the case of traffic on the router the control pings are not sent, but the traffic is monitored.
1. CONFIGURATION OVER WEB BROWSER 1.12 Backup Routes Using the configuration form on the Backup Routes page can be set backing up primary connection by other connections to internet/mobile network. For each back up connection can be defined a priority. Own switching is done based on set priorities and state of the connection (for Primary LAN and Secondary LAN). It is necessary to check the Enable backup routes switching item to enable switching.
1. CONFIGURATION OVER WEB BROWSER 1.13 PPPoE Configuration The PPPoE Configuration item is available only for the industrial router XR5i v2. PPPoE for industrial router works in client mode. Router using connection to the PPPoE server or PPPoE bridge (for example ADSL modem). To enter the PPPoE configuration select the PPPoE menu item. If the Create PPPoE connection option is selected, the router tries to establish PPPoE connection after switching-on.
1. CONFIGURATION OVER WEB BROWSER 1.14 Firewall configuration By the help of a firewall it is possible to set IP addresses from which are possible to remotely access the router and internal network connected behind a router. The choice Allow remote access only from specified hosts is given for easier configuration of hosts. In this firewall configuration it is possible to set up to four remote accesses by the help of Source, Source IP Address, Protocol and Target Port.
1. CONFIGURATION OVER WEB BROWSER Example of the firewall configuration: The router has allowed the following access: • from address 171.92.5.45 using any protocol • from address 10.0.2.123 using TCP protocol on any ports • from address 142.2.26.54 using ICMP protocol Figure 24: Topology of example firewall configuration Figure 25: Example firewall configuration 29 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.15 NAT configuration To enter the Network Address Translation configuration, select the NAT menu item. NAT (Network address Translation / Port address Translation - PAT) is a method of adjusting the network traffic through the router default transcript and/or destination IP addresses often change the number of TCP/UDP port for walk-through IP packets. The window contains sixteen entries for the definition of NAT rules.
1. CONFIGURATION OVER WEB BROWSER Enable the following options and enter the port number is allowed remote access to the router from PPP interface. Item Description Enable remote HTTP access on port If this item field and port number is filled in, then configuration of the router over web interface is possible (disabled in default configuration).
1. CONFIGURATION OVER WEB BROWSER Figure 27: Example NAT configuration 1 In these configurations it is important to have marked choice of Send all remaining incoming packets it default server, IP address in this case is the address of the device behind the router. Connected equipment behind the router must have set Default Gateway on the router. Connected device replies, while PING on IP address of SIM card. 32 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax.
1. CONFIGURATION OVER WEB BROWSER Example of the configuration with more connected equipment: Figure 28: Topology of example NAT configuration 2 Figure 29: Example NAT configuration 2 33 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER In this configuration equipment wired behind the router defines the address Server IP Address. The router replies, while PING on address of SIM card. Access on web interface of the equipment behind the router is possible by the help of Port Forwarding, when behind IP address of SIM is indicating public port of equipment on which we want to come up.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description • TCP client – OpenVPN will communicate using TCP in client mode. UDP/TCP port Port, by which the tunnel will communicate. Remote IP Address IP address of the opposite side of the tunnel. Can be used domain name. Remote Subnet Network IP address of the opposite side of the tunnel. Remote Subnet Mask Subnet mask of the opposite side of the tunnel.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description • Pre-shared secret – enables authentication using Pre-shared secret. This authentication set shared key for both off-side tunnel • Username/password – enables authentication using CA Certificate, Username and Password • X.509 Certificate (multiclient) – enables authentication by CA Certificate, Local Certificate and Local Private Key • X.
1. CONFIGURATION OVER WEB BROWSER The changes in settings will apply after pressing the Apply button. Figure 31: OpenVPN tunnel configuration 37 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER Example of the OpenVPN tunnel configuration: Figure 32: Topology of example OpenVPN configuration OpenVPN tunnel configuration: Configuration A B Protocol UDP UDP UDP Port 1194 1194 Remote IP Address 10.0.0.2 10.0.0.1 Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.0 Local Interface IP Address 19.16.1.0 19.16.2.0 Remote Interface IP Address 19.16.2.0 19.18.1.
1. CONFIGURATION OVER WEB BROWSER 1.17 IPSec tunnel configuration IPsec tunnel configuration can be called up by option IPsec item in the menu. IPsec tunnel allows protected (encrypted) connection of two networks LAN to the one which looks like one homogenous. In the IPsec Tunnels Configuration window are four rows, each row for one configured one IPSec tunnel. Item Description Create This item enables the individual tunnels.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description IKE Mode Defines mode for establishing connection (main or aggressive). If the aggressive mode is selected, establishing of IPsec tunnel will be faster, but encryption will set permanently on 3DES-MD5. IKE Algorithm Way of algorithm selection: • auto – encryption and hash alg. are selected automatically • manual – encryption and hash alg.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description Pre-shared Key Sharable key for both parties tunnel. CA Certificate This certificate is necessary to insert Authentication mode x.509. Remote Certificate This certificate is necessary to insert Authentication mode x.509. Local Certificate This certificate is necessary to insert Authentication mode x.509. Local Private Key This private key is necessary to insert Authentication mode x.509.
1. CONFIGURATION OVER WEB BROWSER Figure 34: IPsec tunnels configuration 42 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER Example of the IPSec Tunnel configuration: Figure 35: Topology of example IPsec configuration IPsec tunnel configuration: Configuration A B Remote IP Address 10.0.0.2 10.0.0.1 Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.0 Local Subnet 192.168.1.0 192.168.2.0 Local Subnet Mas: 255.255.255.0 255.255.255.
1. CONFIGURATION OVER WEB BROWSER Item Description Create Enables the individual tunnels. Description Displays the name of the tunnel specified in the configuration of the tunnel. Edit Configuration GRE tunnel. Table 35: Overview GRE tunnels Figure 36: GRE tunnels configuration Item Description Description Description of tunnel.
1. CONFIGURATION OVER WEB BROWSER Figure 37: GRE tunnel configuration Example of the GRE Tunnel configuration: Figure 38: Topology of GRE tunnel configuration GRE tunnel Configuration: Configuration A B Remote IP Address 10.0.0.2 10.0.0.1 Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.0 Table 37: Example GRE tunnel configuration 45 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.19 L2TP tunnel configuration To enter the L2TP tunnels configuration, select the L2TP menu item. L2TP tunnel allows protected connection by password of two networks LAN to the one which it looks like one homogenous. The tunnels are active after selecting Create L2TP tunnel.
1. CONFIGURATION OVER WEB BROWSER Example of the L2TP Tunnel configuration: Figure 40: Topology of example L2TP tunnel configuration Configuration of the L2TP tunnel: Configuration A B Mode L2TP Server L2TP Client Server IP Address — 10.0.0.1 Client Start IP Address 192.168.1.2 — Client End IP Address 192.168.1.254 — Local IP Address 192.168.1.1 — Remote IP Address — — Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.
1. CONFIGURATION OVER WEB BROWSER 1.20 PPTP tunnel configuration To enter the PPTP tunnels configuration, select the PPTP menu item. PPTP tunnel allows protected connection by password of two networks LAN to the one which it looks like one homogenous. It is a similar method of VPN execution as L2TP. The tunnels are active after selecting Create PPTP tunnel.
1. CONFIGURATION OVER WEB BROWSER Example of the PPTP Tunnel configuration: Figure 42: Topology of example PPTP tunnel configuration Configuration of the PPTP tunnel: Configuration A B Mode PPTP Server PPTP Client Server IP Address — 10.0.0.1 Local IP Address 192.168.1.1 — Remote IP Address — — Remote Subnet 192.168.2.0 192.168.1.0 Remote Subnet Mask 255.255.255.0 255.255.255.
1. CONFIGURATION OVER WEB BROWSER 1.21 DynDNS client configuration DynDNS client Configuration can be called up by option DynDNS item in the menu. In the window can be defined a third order domain registered on server www.dyndns.org. Item Description Hostname Third order domain registered on server www.dyndns.org Username Username for login to DynDNS server Password Password for login to DynDNS server Server If you want to use another DynDNS service than www.dyndns.
1. CONFIGURATION OVER WEB BROWSER 1.22 NTP client configuration NTP client Configuration can be called up by option NTP item in the menu. NTP (Network Time Protocol) allows set the exact time to the router from the servers, which provide the exact time on the network. By parameter Enable local NTP service router is set to a mode in which it operates as an NTP server for other devices in the LAN behind the router.
1. CONFIGURATION OVER WEB BROWSER 1.23 SNMP configuration To enter the SNMP configuration it is possible with SNMP agent v1/v2 or v3 configuration which sends information about the router, eventually about the status of the expansion port CNT or MBUS. SNMP (Simple Network Management Protocol) provides status information about network elements such as routers or end computers. Item Description Name Designation of the router. Location Placing of the router.
1. CONFIGURATION OVER WEB BROWSER Item Description Baudrate Communication speed. Parity Control parity bit: • none – Data will be sent without parity. • even – Data will be sent with even parity. • odd – Data will be sent with odd parity. Stop Bits Number of stop bit. Table 46: SNMP configuration (MBUS extension) Parameters Enable XC-CNT extension and Enable M-BUS extension can not be checked together.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page OID Description .1.3.6.1.4.1.30140.2.1.8.0 Binary input BIN4 (values 0,1) .1.3.6.1.4.1.30140.2.1.9.0 Binary output OUT1 (values 0,1) Table 49: Object identifier for CNT port For the expansion port M-BUS the following range of OID is used: OID Description .1.3.6.1.4.1.30140.2.2.
.1.0 IdNumber – meter number .1.3.6.1.4.1.30140.2.2..2.0 Manufacturer .1.3.6.1.4.1.30140.2.2..3.1. CONFIGURATION OVER WEB BROWSER Example of SNMP settings and readout: Figure 45: Example of SNMP configuration 55 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER Figure 46: Example of the MIB browser It is important to set the IP address of the SNMP agent (router) in field Remote SNMP agent. After enter the IP address is in a MIB tree part is possible show object identifier. The path to objects is: iso → org → dod → internet → private → enterprises → conel → protocols The path to information about router is: iso → org → dod → internet → mgmt → mib-2 → system 56 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel.
1. CONFIGURATION OVER WEB BROWSER 1.24 SMTP configuration To enter the SMTP it is possible configure SMTP (Simple Mail Transfer Protocol) client, which is set by sending emails. Item Description SMTP Server Address IP or domain address of the mail server. Username Name to email account. Password Password to email account. Own Email Address Address of the sender. Table 51: SMTP client configuration Mobile operator can block other SMTP servers, then you can use only the SMTP server of operator.
1. CONFIGURATION OVER WEB BROWSER 1.25 SMS configuration For industrial router XR5i v2 is not available SMS Configuration item. SMS Configuration can be called up by option SMS item in the menu. SMS configuration defines the options for sending SMS messages from the router at different defined events and states of the router. In the first part of window it configuration send SMS. Item Description Send SMS on power up Automatic sending of SMS messages after power up.
1. CONFIGURATION OVER WEB BROWSER Continued from previous page Item Description BIN4 – SMS SMS text messages when activate the binary input on the router. Table 52: Send SMS configuration In the second part of the window it is possible to set function Enable remote control via SMS. After this it is possible to establish and close connection by SMS message. Item Description Phone Number 1 This control can be configured for up to three numbers.
1.
1. CONFIGURATION OVER WEB BROWSER The following table only lists the commands that are supported by Conel’s routers. For other AT commands is always sent OK response. There is no support for treatment of complex AT commands, so in such a case router sends ERROR response.
1. CONFIGURATION OVER WEB BROWSER After powering up the router, at the mentioned the phone number comes SMS in this form: Router (Unit ID) has been powered up. Signal strength –xx dBm. After connect to mobile network, at the mentioned phone number comes SMS in this form: Router (Unit ID) has established connection to mobile network. IP address xxx.xxx.xxx.xxx After disconnect to mobile network, at the mentioned phone number comes SMS in this form: Router (Unit ID) has lost connection to mobile network.
1. CONFIGURATION OVER WEB BROWSER Example of the router configuration for SMS sending via serial interface on the PORT1: Figure 49: Example of SMS configuration 2 63 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER Example of the router configuration for controlling via SMS from every phone numbers: Figure 50: Example of SMS configuration 3 64 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER Example of the router configuration for controlling via SMS from two phone numbers: Figure 51: Example of SMS configuration 4 65 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.26 Expansion port configuration Configuring of the expansion ports PORT1 and PORT2 can cause selecting Expansion Port 1 or Expansion Port 2. Item Description Baudrate Applied communication speed. Data Bits Number of data bits. Parity Control parity bit • none – Will be sent without parity. • even – Will be sent with even parity. • odd – Will be sent with odd parity. Stop Bits Number of stop bit. Split Timeout Time to rupture reports.
1. CONFIGURATION OVER WEB BROWSER When you select items Use CD as indicator of the TCP connection is activated function indication TCP connection using signal CD (DTR on the router). CD Description Active TCP connection is on Nonactive TCP connection is off Table 61: CD signal description When you select items Use DTR as control of TCP connection is activated function control TCP connection using signal DTR (CD on the router).
1. CONFIGURATION OVER WEB BROWSER Example of external port configuration: Figure 53: Example of expansion port configuration 1 Figure 54: Example of expansion port configuration 2 68 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.27 USB port configuration The USB port configuration can be called up by airbrush option USB Port in menu. Configuration can be done, if we have USB/RS232 converter. Item Description Baudrate Applied communication speed. Data Bits Number of data bits. Parity Control parity bit • none – Will be sent without parity. • even – Will be sent with even parity. • odd – Will be sent with odd parity. Stop Bits Number of stop bit. Split Timeout Time to rupture reports.
1. CONFIGURATION OVER WEB BROWSER When you select items Use CD as indicator of the TCP connection is activated function indication TCP connection using signal CD (DTR on the router). CD Description Active TCP connection is on Nonactive TCP connection is off Table 65: CD signal description When you select items Use DTR as control of TCP connection is activated function control TCP connection using signal DTR (CD on the router).
1. CONFIGURATION OVER WEB BROWSER Example of USB port configuration: Figure 56: Example of USB port configuration 1 Figure 57: Example of USB port configuration 2 71 LUCOM GmbH * Ansbacher Str. 2a * 90513 Zirndorf * Tel. 09127/59 460-10 * Fax. 09127/59 460-20 * www.lucom.
1. CONFIGURATION OVER WEB BROWSER 1.28 Startup script In the window Startup Script it is possible to create own scripts which will be executed after all initial scripts. The changes in settings will apply after pressing the Apply button. Figure 58: Startup script Change take effect after shut down and witch on router by the help of button Reboot in web administration or by SMS message.
1. CONFIGURATION OVER WEB BROWSER 1.29 Up/Down script In the window Up/Down Script it is possible to create own scripts. In the item Up script is defined scripts, which begins after establishing a PPP/WAN connection. In the item Down Script is defines script, which begins after lost a PPP/WAN connection. The changes in settings will apply after pressing the Apply button.
1. CONFIGURATION OVER WEB BROWSER 1.30 Automatic update configuration In the window Automatic update it is possible to set automatic configuration update. This choice enables that the router automatically downloads the configuration and the newest firmware from the server itself. The configuration and firmware are stores on the server.
1. CONFIGURATION OVER WEB BROWSER Figure 62: Example of automatic update 1 The following examples find if there is a new firmware or configuration each day at 1:00 in the morning. An example is given on the type of router ER75i v2 with MAC address 00:11:22:33:44:55. • Firmware: http://router.cz/er75i-v2.bin • Configuration file: http://router.cz/00.11.22.33.44.55.cfg Figure 63: Example of automatic update 2 1.
1. CONFIGURATION OVER WEB BROWSER Added module appears in the list of modules on the same page. If the module contains index.html or index.cgi page, module name serves as a link to this page. The module can be deleted using the Delete button. Updating of the module can be done in the same way like adding a new module. Module with a higher (newer) version will replace the existing module. The current module configuration is kept in same state.
1. CONFIGURATION OVER WEB BROWSER 1.32 Change profile To open the dialog box for changing profile select the Change Profile menu item. Profile switch is making by press the button Apply. Change take effect after restarting router by the help of button Reboot in web administration or by SMS message. It is possible select the standard profile or up to three alternative profiles.
1. CONFIGURATION OVER WEB BROWSER 1.34 Set real time clock Disposable setting of the router internal clock can be invoked by pressing the Set Real Time Clock item in the main menu of the web interface. Date and time can be set manually through the Date and Time items. Always enter data in a format that is illustrated in the figure below. The clock can be also adjusted according to the specified NTP server. Finally, it is necessary to press the Apply button. Figure 68: Set real time clock 1.
1. CONFIGURATION OVER WEB BROWSER 1.37 Send SMS For industrial router XR5i v2 is not available Send SMS item. Sending SMS messages is possible in menu Send SMS. The SMS message will be sent after entering the Phone number and text SMS (Message) and by pushing button Send. Figure 71: Send SMS SMS message sending via HTTP request is in the form: GET/send_exec.cgi?phone=%2B420712345678&message=Test HTTP/1.1 Authorization: Basic cm9vdDpyb290 HTTP request will be sent to TCP connection on router port 80.
1. CONFIGURATION OVER WEB BROWSER 1.40 Update firmware To view the information about the firmware version and instructions for its update select the Update Firmware menu item. New firmware is selected via Browse button and update the following pressing the Update button. Figure 73: Update firmware After successful firmware updating the following statement is listed: There is information about updating of the FLASH memory.
2. CONFIGURATION SETTING OVER TELNET 2. Configuration setting over Telnet Attention! If the SIM card isn’t inserted in the router, it is impossible for the router to operate. The Included SIM card must be activated for GPRS transmissions. Monitoring of status, configuration and administration of the router can be performed by means of the Telnet interface. After IP address entry to the Telnet it is possible to configure the router by the help of commands. The default IP address of the modem is 192.168.1.1.
2.