Dear customer, this is a short description to give you some basic informations about the GSM modem you purchased. Informations to the AT commands you will find on the CD as a PDF file. As well informations can be downloaded from our website www.coniugo.com. Those documents can be read and printed with the Adobe Acrobat Reader.
Introduction / Declaration of Conformity = Thank you for buying the ConiuGo GSM/GPRS-, UMTS- or LTE- LAN- Modem. This product was produced according to the latest technology.
Table of contents = 1. Limited Warranty / Limitation of Liability ...............................................4 2. Use as agreed ...........................................................................................5 3. Safety notes ..............................................................................................6 4. Description of the modem .......................................................................7 5. Installation of the modem .............................................
1. Limited Warranty / Limitation of Liability ConiuGo GmbH warrants its product to be free from defects in materials and workmanship under normal use and service for a period of two years from the date of delivery, if no other agreement was made. The warranty is limited to the repair or replacement, at ConiuGo`s sole option. The costs of parts and labour are covered in case of a repair. Costs for mounting and de-mounting, as well as for return transport to ConiuGo GmbH are not covered.
2. Use as agreed = The modem is designed for use in Germany and the European Community. According to the rules of CE-conformity, it is not allowed to distribute this device without a manual in the national language. The manual has to be authorised by the manufacturer. Any distributor has to make sure that the user of the device is capable to understand the manual as regards the content and the language. The modem has to be installed and put into operation by competent technicians.
3. Safety notes The modem corresponds to broadly valid GSM standards. At the use of a GSM transceiver for the mobile communication, certain safety precautions have to be made. GSM products can ignite explosive or inflammable gases. The use of the modem in an environment with a potential for these conditions must be definitely excluded. The system must be switched off in airplanes or hospitals.
4. Description of the modem= The modem is a GSM modem for data-, fax- and SMS- transfer in GSM networks. From the moment the modem is booked into the provider’s network the device behaves like a standard modem or a fax modem. The configuration of the system is carried out via the V.24 serial port resp. the USB-connection. For programming the standard AT-commands according to ETSI-standards (ETSI 07.07 or ETSI 07.05) are used.
Antenna Preferably used is the SMA- Coaxial connector. In dedicated cases the modems can be delivered with FME- or MMCX- connectors as well. 7. Insert the SIM- card Make sure that you have a SIM-card activated for all required services (e.g. CSD data call with a separate calling ID) Place the Modem-unit as shown and insert the SIM-card into the SIM-card reader. Note that the contacts of the SIM card have to be placed upside. Do not touch the connectors of the SIM card with your fingers.
8. Configuration of the LAN- Port= When delivered the LAN- modem is pre-configurated and the LAN- port is addressable with the following IP- setting: IP-address: Subnet- mask: Port: 192.168.1.100 255.255.255.0 10001 All network- an functional- settings are accessible to be changed according to the needs of a user-case: Two ways for changes are possible: 1.) Configuration by using a webinterface Please use the IP- address of the device in your browser (e.g. the IP- address 192.168.1.100) http://192.168.1.
Choose 56700 with GSM/GPRS- module 115200 with UMTS- module 115200 with LTE- module 12
Disable 13
2. Configuration by using Telnet Connect by Telnet with port 9999. Telnet is a software- tool of your operation system. (e.g. Windows XP, Windows 7 and Windows 8) telnet 192.168.1.
9. Attention when changing the Configuration Changes in configuration should be done very carefully. Please test such changes always „step-by-step“. The documentation of all changes is highly recommended in order to keep the ability of access to the webinterface.
10. Reset of webinterface into the state of delivery After applying a lot of changes it might be useful toi reset the webinterface into the state of delivery. However, the button „Apply Defaults“ is resetting the webserver into the state of delivery by the supplier LANTRONIX. To reset the delivery state of the ConiuGo as the producer of this modem it is necessary to apply a few additional settings by manual. This is necessary to establish a perfect communication to the internal GSM modem module.
At first set the default values of the IP- connection and pre-mark those settings by pressing the OK- buttons! 19
Next step ist he correct setting oft he serial port. Please again press the OK- button in order to pre- mark your choice.
Finally choose correctly the connection Settings. Please press the OK- button first but „Apply Settings“ in the next step in order to apply the whole set of parameterst o the webinterface. The webserver will now re-start with ist new settings.
If your browser does show the previous settings of the LANTRONIX webserver the reason is that your browser is showing content from its cache. Refresh the browser content or close & re-open the browser in order to show the actual situation of the webinterface. 11. Setup of a modem- connection Start Telnet in order to access the modem by IP (IP-address and Port). E.g. the default settings when the modem is delivered (192.168.1.100 10001): telnet 192.168.1.
Status question By “AT+CREG?” the registration status is shown by the device. Name of provider network By “AT+COPS?” the provider name is querried and shown by the device. Check of the dial-in- function= Check the dial-in- function as follows: ATDT followed by a phone number. With the command ATH or AT+CHUP you can close a call. = = Sending of an SMS= Call of the SMS- service of the provider: AT+CSCA="+49xxxxxxxxxx" (Example for Germany). The SMS is to be transmitted by PDU- or Text- mode to the modem.
A connection to the LAN- Interface cannot be established right from the start Possible reason: No Crossover- LAN- Cable is used. Remedy: A Crossover- LAN- cable has to be used. A connection to the LAN- Interface was possible in the initial phase, but this capability was lost. Even with the LANTRONIX device installer a connection is no longer possible Possible reason: A network-connection had been entered (IP-address, subnet- mask, etc.), that is not accessible.
The webinterface oft he LANTRONIX- webservers does not accept changes in the configuration settings Possible reason: Changes of the settings had been marked by the „OK“ button, however had not been flashed into the memory of the device by choosing „Apply settings“. or Changes of the settings had been made correctly and are operative („OK“ and final „Apply settings“) However, the browser is showing the previous settings because of loading the website from its cache and not from the webserver (LANTRONIX).
In case of problems please consult our homepage where you will find a lot of documents and whitepapers that will give you support. If you need additional information please send an e-mail to: support@coniugo.
