User manual

Intended use
The wireless selection switch is intended for independently switching on and off up to two devices with a
suitable wireless transmitter of the RSL system.
The permitted connected loads for the devices and their operating voltages can be found in the chapter
“Technical Data”.
Always observe the safety instructions and all other information included in these operating instructions.
Please read the operating instructions before carefully connecting and commissioningand keep these in-
structions.
Any use other than that described above could lead to damage to this product and involves the risk of short
circuits, re, electric shock, etc. No part of the product may be modied or converted!
This product complies with the applicable national and European requirements. All names of companies and
products are the trademarks of the respective owners. All rights reserved.
Package contents
• Wireless selection switch
• 4 cable connections
• Mounting material (screws, wall plugs)
• Operating instructions
Explanation of the symbols
This symbol indicates a health hazard, e.g. electric shock.
The exclamation mark indicates specic risks associated with handling, function and use.
☞
The Hand symbol indicates special tips and operating information.
Safety instructions
Read the complete operating manual carefully before using the product, as it contains
important information about correct installation and operation.
Damages due to failure to follow these operating instructions will void the warranty! We
do not assume any liability for any resulting damage!
We do not assume any liability for material and personal damage caused by improper
use or non-compliance with the safety instructions! The warranty will be voided in such
cases!
Caution!
 Thisproductmayonlybeinstalledbyaqualiedtechnician(e.g.,anelectrician)whois
familiarwiththerelevantregulations(e.g.,VDE,Germanelectricalwiringregulations)!
Improper work carried out on the mains voltage endangers not only your own life, but
also the life of others!
If you do not have the expertise required for the installation, do not install it yourself but
askaqualiedtechnician.
• Unauthorised conversion and/or modication of the product is not allowed for safety and ap-
proval reasons (CE). Never dismantle the product!
• The product is not a toy and does not belong in the hands of children! There is the risk of a
fatal electric shock!
• Do not use this product in hospitals or medical institutions. Although RSL System transmitters
only emit relatively weak radio signals, these may lead to the malfunctioning of life-support
systems. The same may also apply to other areas.
• The product may only be operated on mains voltage (see sections: “Installation and Connec-
tion” and “Technical Data”). Never try to operate the product at another voltage, as this will
result in destruction of the product.
• Only carry out the installation and connection when all the mains cables to the inbuilt wireless
switch are disconnected from the mains voltage. Otherwise, there is a risk of a life-threatening
electric shock!
• The product may be mounted in indoor and outdoor areas (housing with protection type IP66).
However, it must not be installed in or under water. Water can seep into the product, which will
destroy it. Furthermore, this could cause a lethal electric shock!
• An all-pole disconnection from the mains voltage (such as a surge protector) must be provided
as part of the wiring set-up.
• The product may only be assembled and operated in a stationary condition; the product is not
suitable for installation and operation in vehicles.
• Do not mount or use this product in rooms or under adverse environmental conditions where
combustible gases, vapours or dust are are or may be present! There is a risk of explosion!
• The product must not be exposed to extreme temperatures, strong vibrations or heavy mecha-
nical stress.
• If it can be assumed that safe operation is no longer possible, the device must be turned off
and precautions must be taken to ensure that it is not used unintentionally. Do not touch the
inbuilt wireless switch or any device connected to it.
Disconnect the wireless selection switch completely from the mains by switching off at the
appropriate circuit breaker or by pulling out the fuse and switching of the corresponding earth
leakage breaker.
After this, arrange for an expert to check the product.
• Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (where there is ickering light, leaking
smoke or a smell of burning, audible crackling noises, or discolouration of the product or to
adjacent surfaces)
- the device has been stored under adverse conditions
- it was exposed to heavy loads during transport
• Do not leave packaging material carelessly lying around, since it could become a dangerous
plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer’s Liability Insu-
rance Association for Electrical Systems and Operating Facilities are to be observed!
• If you have any questions that are not answered in this manual, please contact our technical
service or other specialist.
Installation and connection
Please refer to the section “Safety instructions”!
The wireless inbuilt switch can be mounted at a suitable place. The housing of the wireless
inbuilt switch is protected according to IP66. Thus, it may be installed in unprotected outdoor
areas. Make sure that the housing is never in or under water.
The wireless inbuilt switch must be disconnected from the mains supply during installation. Turn
off the mains supply, by switching off the appropriate circuit breaker or by pulling out the fuse.
Secure it against unauthorised reconnection, e.g., with a danger sign.
Furthermore, turn off the earth leakage circuit breaker to disconnect all the poles from the mains
voltage.
Check that the mains connection is current free with a suitable tester.
• Open the cover of the protective housing by removing the 4 screws on the top with a screwdriver. You can
then remove the cover.
1
2
3
4
5
7
6
8910
11
1 Opening for mounting the housing to a wall
2 Button for switching channel 1
3 LED
4 Button for switching channel 2
5 Cover for screw terminals/pull reliefs
6 Filler plug (x 8)
7 3x terminals for protective conductor
8 Output L/N for switching channel 1
9 Output L/N for switching channel 2
10 Input L/N and PE (earth symbol)
11 Pull reliefs
• The complete inbuilt switch unit can be removed from the housing.
• Remove the two screws on the cover (5) and remove the cover. The screw terminals for the two outputs/
switching channels (8 + 9), the input for power supply (10) and the pull reliefs (11) for the connection cables
are situated under the cover.
• Depending on the installation location and the position of the connecting cables, up to 4 ller plugs (6) can
be used instead of the 4 cable connections provided.
Makes sure that the rubber seals of the cable connections make good contact with the housing and are not
kinked.
• Depending on the type of wall, suitable screws and wall plugs are required for mounting the housing to a
wall.
Select an installation location that is not in direct vicinity to other transmitters. Maintain distance
to metal parts as this can reduce the range considerably.
If you have to drill holes for wall plugs, mark the installation location on the wall through the four holes (1)
at the housing corners. The distance between the holes is 100 x 80 mm, as indicated on the back of the
housing.
Pay attention when drilling and tightening the screws that no cables or pipes are damaged.
• Push the power cable and the connection cables for the devices through the cable connections.
• Slacken the three pull reliefs.
G
OPERATINGINSTRUCTIONS www.conrad.com
Wireless selection switch RSL
Item no. 1078741
Version 04/16