Ez One Shot BARCODE SCANNER USER’S MANUAL Version: 2014.
CONTENTS PREFACE Table of Contents.......................................................2-3 LED & Beeper Indication..............................................4 Cloning Mode............................................................ 5-6 How to fix the scanner to the terminal.......................7-8 How to change a cable.................................................8 How to set up the parameter........................................
CONTENTS SYMBOLOGIES (GROUP 35 - 52) 35~37 Enable/Disable Barcode Symbology.......... 44-46 37 China postcode(Toshiba code)............................... 46 38 MSI code, UK Plessey code...................................48 39 Code 93, Telepen, IATA..........................................50 40 Interleaved 2 of 5, Code 11.................................... 52 41 Industrial 2 of 5, Matrix 2 of 5................................. 54 42 Codabar..................................................................
LED & BEEPER INDICATION Status Blue/Green LED Initializing/ Power-up Red LED Beeper Solid for 2 sec 1 long beep Successful Barcode Scan 1 Flash 1 beep Successful Connection 2 Flashes 2 beeps Reads Configuration Barcode Data Temporarily/ Permanently Stored Scanner 2 beeps 2 short beeps 1 Flash Wireless Solid for 2 sec Disconnection 3 short beeps Scan RESET/ ABORT and retry Scan Pincode Stop and retry Unsuccessful Pincode Setup Flashing 3 short beeps Barcode Scann w/o Connection Flash
CLONING MODE WHAT IS CLONING MODE? CLONING duplicates a scanners settings in other scanners. It can save time when a number of scanners must be programmed to the same settings. HOW SHOULD CLONING WORK? 1. Using this guide, make all the necessary settings for one wand. 2. Scan the CLONING MODE bar code shown below. 3. When CLONING MODE is scanned, all setup parameters will be converted to alphanumeric characters and shown on the monitor. 4.
CLONING MODE EXAMPLE : 1. PROJECT ASSIGNMENTS: 1.1. Beep tone: BEEP LOW -- HIGH. 1.2. Capslock Mode: CAPSLOCK ON. 1.3. Reading Mode: CONTINUOUS AUTO OFF. 2. SETTING PROCEDURE: 2.1. Scan BEEP LOW -- HIGH (GROUP 3). 2.2. Scan CAPSLOCK ON (GROUP 11). 2.3. Scan CONTINUOUS AUTO OFF (GROUP2). 3. All parameters will be converted to alphanumeric characters and shown on the monitor. .A017$ ....0604 5A025F04 . 4. Print the results shown on the monitor as bar codes with a bar code printer.
HOW TO CONNECT THE SCANNER TO THE HOST TERMINAL: Handheld Barcode Scanner KEYBOARD WEDGE INTERFACE 1. Power down the host computer. 2. Disconnect the keyboard cable from the computer. 3. Connect the “Y ” cable between the keyboard and the scanner and computer. 4. Restart the computer. 5. The scanner will beep. 6. Set the scanner to KEYBOARD interface by referring to GROUP 13 (Interfaces) 7. Scanner will beep to confirm the setting. 8. Scan a bar code to confirm that data shows on the monitor.
USB INTERFACE The USB Interface supported is compatible with Apple MAC series, later PCs and Windows 98, 2000, Me and XP, Vista. 1. Connect the USB cable between the scanner and the computer. 2. The scanner will beep. 3. The scanner will detect the USB driver automatically. (The first time the scanner is connected via the USB port, follow the appropriate instructions for the host computer.) 4. Set the scanner to KEYBOARD/USB interface by referring to GROUP-13 (Interfaces) 5.
HOW TO SET PARAMETERS How do you program a scanner with this user’s guide? 1. Use the scanner to scan at the bar code representing the function/ parameter you want to set. 2. When you hear two beeps, the new settings have been defined or updated into the memory processor. Default parameters are indicated in bold type and underlined characters. The character font is ARIAL BLACK. CD = Check Digit. CDV = Check Digit Verification.
GROUP-1 GENERAL SETTINGS . A001$ DEFAULT *Reset to factory default . A007$ CHECK VERSION *Check firmware version .
GROUP-2 GENERAL SETTINGS - READING MODE . F005$ CONTINUOUS MODE . F001$ FLASH MODE . F002$ TRIGGER MODE . F006$ CONTINUOUS AUTO OFF . F003$ TOGGLE MODE . F007$ *AUTO SENSING MODE (CCD) . F010$ *AUTO SENSING MODE (Laser) LED is always on. The trigger does not function in Continuous Mode. The LED is on steady if a bar code is close to the scanner, but starts flashing if no bar code is detected after 60 seconds. The trigger does not function in Flash Mode.
GROUP-3 GENERAL SETTINGS BEEP TONE 2.7KHz Buzzer (Wireless Scanner) 2.1KHz Buzzer (Tethered Scanner) . F012$ .F019$ BEEP OFF BEEP HIGH . F014$ .F021$ BEEP HIGH . F016$ BEEP HIGH--LOW .F018$ BEEP HIGH--LOW BEEP MEDIUM .F020$ . F013$ BEEP MEDIUM . F015$ BEEP LOW--HIGH .F022$ BEEP LOW--HIGH . F017$ BEEP LOW BEEP LOW TERMINATOR . D010$ NONE . D013$ CR+LF . D014$ . D011$ TAB . D015$ LF . D012$ SPACE CR .
GROUP-4 SEND DATA LENGTH, PREAMBLE & POSTAMBLE. SEND DATA LENGTH .D019$ SEND DATA LENGTH ON .D020$ SEND DATA LENGTH OFF PREAMBLE & POSTAMBLE ( PREFIX AND SUFFIX ) . A011$ CLEAR PRE/ POSTAMBLE . A012$ PREAMBLE (16) . A013$ POSTAMBLE (16) EXAMPLE: Set PREAMBLE String as “ ## ” POSTAMBLE String as “ $$ ” SETTING PROCEDURE: STEP 1 : Scan : CLEAR PRE/ POSTAMBLE. STEP 2 : Scan : PREAMBLE. STEP 3 : Scan : “ # ” twice from FULL ASCII Table. STEP 4 : Scan : PREAMBLE. STEP 5 : Scan : POSTAMBLE.
GROUP-5 GENERAL SETTINGS - ACCURACY ADJUSTMENT 0 5 1 6 2 7 3 8 4 9 . A010$ ACCURACY ADJUSTMENT Accuracy Adjustment assures a more reliable decoded output. Enabling the feature and setting a number from 1 to 9 subjects the decoded output a higher standard of accuracy. The higher the number, the greater the accuracy. SETTING PROCEDURE: 1. Scan ACCURACY ADJUSTMENT. 2. Scan one digit (1~9) from barcode menu above. 3. Scan ACCURACY ADJUSTMENT. . P023$ NOTES: 1.
GROUP-6 GENERAL SETTINGS ENABLE INVERSE BARCODE .D021$ DISABLE INVERSE BARCODE [READS POSITIVE BARCODE ONLY] .D022$ ENABLE INVERSE BARCODE [READS POSITIVE & NEGATIVE BARCODES] ENABLE CODE ID .A008$ FACTORY ID ON .A014$ AIM ID ON .A015$ SET ID ON DISABLE CODE ID .A009$ NOTES: 1. Only ONE code ID will be sent. 2. The code ID is located at the position before the bar code data and after the preamble. EXAMPLE : 1.Preamble 145287, 2.Code ID: enable AIM ID, 3.
GROUP-7 GENERAL SETTINGS SYMBOLOGIES CODE ID IDENTIFIER Symbologies Factory AIM ID ID (new) T K Symbologies ]C1 ]C0 MSI ]E4 Code 32 ]E4 Codabar EAN8(+5 ON) ]E4 Codabar(ABC Codabar) UPC-E(+2/+5 OFF) ]E0 Codabar(CDV & Send CD) ]E3 Codabar(CDV & not send CD) ]E3 ]E0 UK Plessey ]E3 Full ASCII Code 39(disable CDV) UPC-A(+5 ON) ]E3 Full ASCII Code 39(CDV & send CD) EAN-13(+2/+5 OFF) ]E0 Full ASCII Code 39(CDV & not send CD) ]E3 Standard Code 39(disable CDV) ]E3 Standard Code 39(CDV
GROUP-8 GENERAL SETTINGS - SET CODE ID . P001$ EAN 13 Set ID . P002$ EAN 8 Set ID . P003$ UPC E Set ID . P004$ UPC A Set ID . P005$ Code 39 Set ID . P013$ Code 93 Set ID . P007$ Codabar Set ID . P021$ IATA Set ID . P010$ Code 128 Set ID . P016$ EAN 128 Set ID . P022$ Telepen Set ID . P009$ Code 11 Set ID . P011$ Code 32 Set ID .
GROUP-9 GENERAL SETTINGS - SET CODE ID . P014$ MSI Code Set ID . P015$ UK Plessey Set ID . P017$ Matrix 2 of 5 Set ID . P006$ Interleaved 2 of 5 Set ID . P018$ Industrial 2 of 5 Set ID . P008$ Full ASCII Code39 Set ID . P019$ GS1 Databar (RSS) Limited Set ID . P020$ GS1 Databar (RSS) Expanded Set ID . P024$ GS1 Databar (RSS) Set ID . P020$ LABEL Code Set ID [ Reserved ] . P023$ 1. The scanner will beep three times as a reminder that a setting is not yet complete. 2.
GROUP-10 GENERAL SETTINGS INTERBLOCK DELAY 0mS 10mS 50mS 100mS 200mS 500mS INTERCHARACTER DELAY 140uS 500uS 1mS 4mS 16mS
GROUP-11 GENERAL SETTINGS KEYBOARD LAYOUT . C010$ . C009$ JAPAN (106 key) . C025$ ENGLISH (USA) . C018$ CANADIAN (FRENCH) . C034$ ENGLISH (UK) . C012$ CANADIAN (TRADITIONAL) . C029$ FRENCH . C011$ NORWEGIAN . C026$ GERMAN . C014$ SWEDISH . C031$ ITALIAN . C013$ PORTUGUESE . C030$ SPANISH . C017$ BELGIAN (AZERTY) . C028$ CZECH (QWERTY) . C022$ DUTCH . C027$ CZECH (QWERTZ) . C021$ DANISH . C032$ HUNGARIAN (QWERTZ) . C024$ SLOVAK . C033$ HUNGARIAN (101 KEY) .
GROUP-12 GENERAL SETTINGS CAPITAL LOCK MODE . A005$ . A004$ CAPLOCK OFF CAPLOCK ON . A006$ CAPLOCK FREE NOTE: 1. When barcode scanner is set to Caplock Free mode, no matter keyboard Capslock LED indicator is ON or OFF, output will be always the same as the Original barcode. In other words, what you see is what output is.(CODABAR is the exception) 2. If ABCD/ ABCD, abcd/ abcd, ABCD/T*E, abcd/tn*e are on, they work independently according to their rules. NUMERIC KEY . D017$ NUMERIC KEY .
GROUP-13 TETHERED SCANNER SETTINGS . C004$ PC-AT COMPUTER TYPE . C007$ NOTEBOOK* SYMPTOMS Scanner seems to be performing as usual, but no data is being output. SOLUTION 1. Unplug the cable from the host computer. 2. Plug the cable back into the host computer. 3. Set the scanner to the exact computer type immediately. CauƟon: Please ensure the correct computer type is set when the scanner is aƩached to a new host computer. If set to Notebook, the scanner will operate with no external keyboard. .
GROUP-14 TETHERED SCANNER SETTINGS (The following are only supported by Bi-Color models) BI-COLOR: CYCLE MODE . D027$ *.D027$* GREEN > RED . D028$ *.D028$* RED > GREEN . D029$ *.D029$* GREEN > BI-COLOR . D030$ *.D030$* RED > BI-COLOR 1. Illumination color will switch back and forth from one to another when good read does not occur. 2. Illumination color will remain as the one used at the last good read. BI-COLOR: SINGLE MODE . D031$ *.D031$* BI-COLOR . D032$ *.D032$* GREEN . D033$ *.
GROUP-15 ADVANCED AUTO-SENSING SETTINGS (The following is only supported by autosensing models) MAGNETIC SWITCH (CCD & LASER SCANNERS) . F034$ MAGNETIC SWITCH ON . F035$ MAGNETIC SWITCH OFF NOTES: 1. The Magnetic Switch is automatically activated when AutoSensing Mode is on. 2. To enable Magnetic Switch, the scanner should be paired with an Autosense Stand to perform Auto-Sensing function. 3. When Magnetic Switch is disabled, the scanner will perform Auto-Sensing function without Autosense Stand.
GROUP-16 ADVANCED AUTO-SENSING SETTINGS (The following is only supported by autosensing models) DEACTIVATION TIME (CCD & LASER SCANNERS) . F030$ DEACTIVATION TIME NOTES: 1. The default of Deactivation Time is 3 Sec. 2. Deactivation Time is the time interval between the last scan and the automatic deactivation of LED or Laser light in Auto-Sensing Mode. 3. You can set the Deactivation Time value by the following three steps: Step 1: scan Deactivation Time Step 2: scan two digits(Limit Range: 01 ~ 30sec.
GROUP-17 TETHERED SCANNER - RS232 SETTINGS BAUD RATE . E001$ . E005$ 4800 . E006$ 300 . E002$ 9600 . E007$ 600 . E003$ 19200 . E022$ 1200 . E004$ 38400 2400 DATA BITS & PARITY . E012$ . E008$ 8 Bits SPACE 8 Bits None . E009$ . E013$ 7 Bits EVEN . E014$ 8 Bits EVEN . E010$ 7 Bits ODD . E015$ 8 Bits ODD . E011$ 7 Bits MARK .
GROUP-18 TETHERED SCANNER - RS232 SETTINGS STOP BITS . E016$ 1 STOP BIT . E017$ 2 STOP BITS HANDSHAKING . E018$ NONE . E019$ RTS enable at Power on . E020$ RTS enable with Communication ACK / NAK . E023$ ON . E024$ OFF FLOW CONTROL: TIME OUT . E025$ 1 Sec . E026$ 3 Sec . E027$ 10 Sec . E028$ Unlimited BCC . E029$ RS232 BCC Char On .
GROUP-19 TETHERED SCANNER - WAND EMULATION SETTINGS . D001$ 200us LEVEL DURATION OF MINI WIDTH . D002$ 600uS . D003$ LOW POLARITY OF IDLE CONDITION . D004$ HIGH . D005$ Bar High / Space Low OUTPUT OF WAND EMULATION . D006$ Bar Low / Space High . D007$ PEN TYPE .
GROUP-20 WIRELESS SCANNER SETTINGS INTERFACE . C035$ *.c035$* WIRELESS The scanner’s interface is Wireless by default. After scanning above barcode, please select one bluetooth profile on the next page. . C008$ *.c008$* USB-HID Please connect the scanner with the host with mini USB cable before scanning above barcode. . C006$ *.
GROUP-21 WIRELESS SCANNER SETTINGS BLUETOOTH PROFILE . E043$ (Recommanded) BT mode - HID 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - HID]; the scanner will emit several beeps. 4. Select “Wireless Scanner” from discovered device list. (For PC, please click “Create a pairing code for me”) 5. The Bluetooth application may prompt you to scan a pincode. 6. Follow the steps in PINCODE SETUP section the on next page. 7.
GROUP-22 WIRELESS SCANNER SETTINGS PINCODE SETUP . E032$ STEP 1 Pincode Start STEP 2 Scan numeric barcodes (see NUMERIC BARCODES below) based on the pincode generated by the Bluetooth application. NUMERIC BARCODES 1 6 2 7 3 8 4 9 5 0 STEP 3 $TX Enter STEP 4 Pincode Stop .
GROUP-23 WIRELESS SCANNER SETTINGS Getting Connected - iOS (Apple) Simply follow instruction in [BT mode - HID]. (Group 21), in which step 5 & 6 can be skipped since Apple devices will not require pincode for connection. Touch Keyboard . E047$ ENABLE iOS HOTKEY . E048$ DISABLE iOS HOTKEY After enabling iOS Hotkey(disabled by default), you may simply double-click the trigger to toggle the iPhone/iPad Touch Keyboard. Getting Connected - Android (Samsung, hTC, Sony..
GROUP-24 WIRELESS SCANNER SETTINGS POWER OFF TIMEOUT Variable Timeout . B030$ *.B030$* *.B029$* SET MINUTE (Range: 00 ~ 60) . B029$ SET SECOND (Range: 00 ~ 60) The timeout is 3 minutes by default, and is programmable to the second and minute, ranging from 10 seconds (00:10) to 60 minutes and 60 seconds (60:60) For example, to set the timeout as 5 minutes 30 seconds: 1. Scan [Set Minute] 2. Scan [0] & [5] on below numeric barcode table. 3. Scan [Set Minute] 4. Scan [Set Second] 5.
GROUP-25 WIRELESS SCANNER SETTINGS SET BLUETOOTH DEVICE ID To customize your own Bluetooth device name for the wireless scanner, please follow below steps: STEP 1 . B022$ Default Wireless ID STEP 2 . B023$ Set Wireless ID STEP 3 Scan up to 16 alphanumeric characters from Full ASCII Table (GROUP 35-41) as your desired ID name. STEP 4 . B023$ Set Wireless ID STEP 5 Scan a desired BT mode in BLUETOOTH PROFILE (GROUP 21) to complete the configuration. *Note: 1.
GROUP-26 WIRELESS SCANNER SETTINGS SET SPP PINCODE By default, the pincode under SPP profile for the scanner is “1234”. You may customize this pincode with below steps: STEP 1 . B024$ Set SPP Pincode STEP 2 Scan numeric barcodes (see NUMERIC BARCODES below) Up to 8 numbers can be set as SPP pincode. NUMERIC BARCODES 1 6 2 7 3 8 4 9 5 0 STEP 3 . B024$ Set SPP Pincode STEP 4 Scan a desired BT mode in BLUETOOTH PROFILE (GROUP 21) to complete the configuration.
GROUP-27 WIRELESS SCANNER SETTINGS SPP MASTER MODE First, please generate one configuration barcode for the target SPP slave device in below methods: 1. The barcode must be Code 39 with no checksum 2. Barcode data format: LTB + Target MAC address For example, the target SPP slave device’s MAC address is 001583522C3B. Please encode: *LTB001583522C3B* in Code39 barcode. Then, follow below steps to create connection: STEP 1 .
GROUP-28 WIRELESS SCANNER SETTINGS SPP REMOTE CONTROL There are two ways to verify connection status by the host under SPP profile. Command Response Host sends: Scanner replys: CR,LF,{,A,L,},CR,LF O,K,CR,LF (8 bytes) (4 bytes) CR,LF,{,M,1,},CR,LF a short beep (8 bytes) Beeper Response Host sends: Scanner reacts: SHUT DOWN This configuration barcode will shut down the scanner immediately but still reserve the pairing record. . E255$ SHUT DOWN DISCONNECTION .
GROUP-29 WIRELESS SCANNER SETTINGS BATCH MODE . E054$ ENABLE . E053$ DISABLE When out of range, the scanner will temporarily keep scanned data in its memory buffer(2K RAM) until the buffer is full. When back in range, the scanner will send all stored data back to the host. *Note: 1. Batch Mode will not function when Memory Mode is enabled, or no connection is made beforehand. BINARY CHECK CHARACTER . E029$ *.e029$* *.e030$* ENABLE .
GROUP-30 WIRELESS SCANNER SETTINGS MEMORY MODE For memory version only . R001$ *.R001$* *.R002$* ENABLE MEMORY . R002$ DISABLE MEMORY Once enabled, the scanner will stop sending data via Bluetooth and start storing data into the internal flash disk (2MB) Delete Last Record/ Clear All Record . R005$ *.R005$* *.R004$* DELETE LAST RECORD .
GROUP-31 WIRELESS SCANNER SETTINGS DATA OUTPUT For memory version only . R003$ OUTPUT DATA Data Output - Interface WIRELESS *.R003$* . C035$ *.c035$* *.c008$* *.C006$* . C008$ USB-HID . C006$ USB-VCP Data Output - Wireless Method To output stored data via WIRELESS, please do the following: 1. Scan [WIRELESS] 2. Follow the steps on Group 21 to connect to host via HID or SPP. 3. Scan [ENABLE MEMORY] (Group 30) and scan your desired barcodes. 4.
GROUP-32 WIRELESS SCANNER SETTINGS DATA FORMAT For memory version only . R011$ *.R011$* DATA FORMAT The default Data Format is - , ,
GROUP-33 WIRELESS SCANNER SETTINGS DATE FORMAT For memory version only . R008$ *.R008$* DATE FORMAT The default Date Format is DD/MM/YYYY (Code = 09), below is full list of available formats and their setup codes: Code Format Code Format 01 02 03 04 05 06 07 08 DD-MM-YYYY MM-DD-YYYY DD-MM-YY MM-DD-YY YYYY-MM-DD YY-MM-DD DD-MM MM-DD 09 10 11 12 13 14 15 16 DD/MM/YYYY MM/DD/YYYY DD/MM/YY MM/DD/YY YYYY/MM/DD YY/MM/DD DD/MM MM/DD Example: To set Date Format to MM/DD/YY (Code =12) 1.
GROUP-34 WIRELESS SCANNER SETTINGS QUANTITY For memory version only . R017$ ENABLE QUANTITY INPUT *.R017$* Once you enable quantity input, the operation procedure under memory mode will be as follows: 1. Scan [ENABLE MEMORY] (Group 30) 2. Set DATA FORMAT (Group 32) as appropriate. For example, your data format is , . 3. Scan a random barcode; it will be stored as . 4. Scan [SET QUANTITY] 5.
GROUP-35 ENABLE/ DISABLE SYMBOLOGIES ENABLE . A002$ DISABLE . A003$ ENABLE ALL CODE . K010$ CODE 32 . K001$ CHINA POSTAL CODE . L010$ DISABLE ALL CODE . K011$ CODE 32 . K002$ CHINA POSTAL CODE . L011$ UK PLESSEY CODE . N001$ UK PLESSEY CODE . N002$ INDUSTRIAL 2 OF 5 . M010$ INDUSTRIAL 2 OF 5 . M011$ MATRIX 2 OF 5 . J001$ INTERLEAVED 2 OF 5 . J010$ CODE 128 . I 001$ CODABAR MATRIX 2 OF 5 . J002$ INTERLEAVED 2 OF 5 . J011$ CODE 128 . I 002$ . L014$ CODABAR .
GROUP-36 ENABLE/ DISABLE SYMBOLOGIES ENABLE . H001$ UPC-A . H007$ UPC-E . H019$ EAN-8 . H013$ DISABLE . H002$ UPC-A . H008$ UPC-E . H020$ EAN-8 . H014$ EAN-13 . L001$ EAN-13 . L002$ MSI . G008$ CODE 39 . I 010$ MSI . G009$ CODE 39 . I 011$ CODE 11 . G010$ CODE 11 . G011$ CODE 93 . M001$ EAN-128 . N017$ CODE 93 . M002$ EAN-128 .
GROUP-37 ENABLE/DISABLE SYMBOLOGIES, CHINA POSTAL CODE ENABLE . N032$ GS1 Databar ENABLE DISABLE . N033$ . N038$ GS1 Databar DISABLE GS1 Databar STACKED ENABLE . N039$ . N010$ GS1 Databar STACKED DISABLE GS1 Databar LIMITED ENABLE . N011$ . N026$ GS1 Databar LIMITED DISABLE GS1 Databar EXPANDED ENABLE . N027$ . N028$ GS1 Databar EXPANDED DISABLE GS1 Databar EXPANDED STACKED ENABLE . N029$ . G021$ PDF 417 ENABLE GS1 Databar EXPANDED STACKED DISABLE .
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-38 SYMBOLOGIES: MSI CODE, UK PLESSEY CODE MSI . L001$ ENABLE . L008$ . L002$ CHECK DIGIT DOUBLE 11 PLUS MOD 10 DISABLE . L009$ . L004$ CHECK DIGIT SINGLE MOD 10 CDV & SEND CD . L005$ . L003$ MIN LENGTH [ 6 ] CDV & NOT SEND CD . L006$ . L007$ MAX LENGTH [ 48 ] CHECK DIGIT DOUBLE MOD 10 . L010$ ENABLE . L011$ DISABLE UK PLESSEY CODE . L012$ CDV & SEND CD .
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-39 SYMBOLOGIES: CODE 93, TELEPEN, IATA . G010$ CODE 93 . G012$ ENABLE . G011$ DISABLE MIN LENGTH [ 6 ] . G013$ MAX LENGTH [ 48 ] . L014$ TELEPEN . L020$ ENABLE TELEPEN . L015$ TELEPEN ASCII . L021$ DISABLE TELEPEN TELEPEN NUMBER . N017$ ENABLE . N018$ IATA . N021$ CDV & NOT SEND CDV DISABLE . N022$ . N019$ MIN LENGTH [ 6 ] DISABLE CDV . N020$ CDV & SEND CD .
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-40 SYMBOLOGIES: INTERLEAVED 2 OF 5, CODE 11 . J001$ ENABLE INTERLEAVED 2 OF 5 . J008$ . J002$ First digit suppressed DISABLE . J009$ . J003$ Last digit suppressed DISABLE CDV . J004$ CDV & SEND CD . J014$ NO suppressed . J006$ . J005$ MIN LENGTH [ 6 ] CDV & NOT SEND CD . J007$ MAX LENGTH [ 48 ] . I 010$ ENABLE CODE 11 . I 043$ . I 011$ CDV & SEND CD (2 DIGITS) DISABLE . I 012$ DISABLE CDV . I 013$ CDV & SEND CD . I 014$ CDV & NOT SEND CD . I 015$ MIN LENGTH [ 6 ] . I 016$ .
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-41 SYMBOLOGIES: INDUSTRIAL 2 OF 5, MATRIX 2 OF 5 . N001$ INDUSTRIAL 2 OF 5 . N005$ ENABLE . N002$ DISABLE CDV & NOT SEND CD . N006$ . N003$ MIN LENGTH [ 6 ] DISABLE CDV . N004$ . N007$ MAX LENGTH [ 48 ] CDV & SEND CD . M010$ ENABLE . M011$ DISABLE MATRIX 2 OF 5 . M014$ CDV & NOT SEND CD . M015$ . M012$ MIN LENGTH [ 6 ] DISABLE CDV . M013$ CDV & SEND CD .
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-42 SYMBOLOGIES: CODABAR . I 001$ ENABLE CODABAR . I 007$ . I 002$ CDV & NOT SEND CD DISABLE . I 008$ . I 005$ MIN LENGTH [ 6 ] DISABLE CDV . I 009$ . I 006$ MAX LENGTH [ 48 ] CDV & SEND CD . I 030$ ST/SP: abcd/abcd START / STOP . I 003$ . I 029$ SEND START / STOP ST/SP: ABCD/ABCD . I 004$ . I 031$ ST/SP: ABCD/TN*E . I 032$ ST/SP: abcd/tn*e . I 027$ CLSI FORMAT ON .
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-43 SYMBOLOGIES: ABC- CODABAR, CX- CODABAR . I 017$ ON . I 018$ OFF . I 035$ ABC- CODABAR . I 039$ INSERT DATA- ON . I 036$ INSERT DATA- OFF SET INSERT DATA* The data can be any alphanumerics of FULL ASCII Table (GROUP 53-61) ABC-CODABAR (American Blood Commission). The ABC Code is an acronym for American Blood Commission. This bar code is a variant of the CODABAR Code developed for the use in the blood bank. This Code consists of two bar codes which are decoded in one read cycle.
GROUP-44 SYMBOLOGIES: CODABAR COUPLING, ADJACENT REQUIRED . I 019$ CODABAR COUPLING . I 041$ ON . I 020$ OFF INSERT DATA - ON . I 026$ .
GROUP-45 SYMBOLOGIES: STANDARD & FULL ASCII CODE 39, CODE 32 STANDARD CODE 39 & FULL ASCII 39 . G003$ . G008$ DISABLE CDV ENABLE . G004$ . G009$ DISABLE . G001$ CDV & SEND CD . G005$ CDV & NOT SEND CD FULL ASCII CODE 39 ENABLE . G006$ . G002$ MIN LENGTH [ 1 ] FULL ASCII CODE 39 DISABLE . G014$ START / STOP - SEND . G007$ MAX LENGTH [ 48 ] . G015$ START / STOP Not SEND NOTE: The default for Code 39 is Standard Code 39.
APPENDIX FULL ASCII ( Code 39 ) NUMERIC TABLE 0 1 2 3 4 5 6 7 8 9 SETTING PROCEDURE MIN / MAX LENGTH STEP 1 - Scan: MIN LENGTH/ MAX LENGTH STEP 2 - Scan: Two digits from Appendix. STEP 3 - Scan: MIN LENGTH/ MAX LENGTH Please note that when Min Length and / or Max Length are enabled, the scanner will only read bar codes that fall into those length parameters. Bar codes shorter or longer than specified will not be read.
GROUP-46 SYMBOLOGIES FORMATTING: UPC-E . H007$ ENABLE UPC-E . H010$ . H008$ LEAD DIGIT NO SEND DISABLE . H011$ . H009$ CHECK DIGIT SEND LEAD DIGIT SEND . H012$ CHECK DIGIT NO SEND . H037$ ADD ON SUPPLEMENT +5 ON . H047$ . H038$ + 5 OFF ADD A SPACE ON . H048$ . H039$ ADD A SPACE OFF +2 ON . H056$ . H040$ + 2 OFF ADDENDA REQUIRED ON . H055$ ADDENDA REQUIRED OFF NOTE: If ADDENDA REQUIRED is set to ON, the scanner will only read an UPC-E bar code that has an addenda.
GROUP-47 SYMBOLOGIES: UPC-E SYSTEM NUMBER UPC-E0 . H064$ E [ 0 ] OFF . H063$ E ( 0 ) ON UPC-E1 . H065$ E [ 1 ] ON . H066$ E ( 1 ) OFF NOTE: Most UPC bar codes lead with 0 number systems, for these bar codes use UPC E(0) selection. For the bar codes that lead with the 1 number, use UPC E(1) selection. UPC-E EXPAND TO UPC-A . H053$ ENABLE . H054$ DISABLE NOTE: 1. If UPC-E EXPAND TO UPC A FORMAT is enabled, the output of UPC-A will be 12 digits. 2.
GROUP-48 SYMBOLOGIES FORMATTING: UPC- A . H001$ ENABLE . H002$ DISABLE . H003$ LEAD DIGIT SEND UPC- A . H004$ LEAD DIGIT NO SEND . H005$ CHECK DIGIT SEND . H006$ CHECK DIGIT NO SEND UPC-A EXPAND TO EAN-13 . H068$ ENABLE . H067$ DISABLE . H033$ ADD ON SUPPLEMENT . H045$ +5 ON . H034$ + 5 OFF . H035$ ADD A SPACE ON . H046$ ADD A SPACE OFF . H060$ +2 ON . H036$ + 2 OFF ADDENDA REQUIRED ON .
GROUP-49 SYMBOLOGIES FORMATTING: EAN 8 . H019$ ENABLE . H020$ DISABLE EAN-8 . H022$ LEAD DIGIT NO SEND . H023$ . H021$ CHECK DIGIT SEND LEAD DIGIT SEND . H024$ CHECK DIGIT NO SEND . H029$ + 5 ON ADD ON SUPPLEMENT . H043$ . H030$ ADD A SPACE ON + 5 OFF . H044$ . H031$ ADD A SPACE OFF + 2 ON . H062$ . H032$ ADDENDA REQUIRED ON + 2 OFF . H061$ ADDENDA REQUIRED OFF NOTE: If ADDENDA REQUIRED is set to ON, the scanner will only read an UPC-E bar code that has an addenda.
GROUP-50 SYMBOLOGIES FORMATTING: EAN13, ISBN, ISSN, ISMN . H013$ ENABLE EAN-13 . H016$ . H014$ LEAD DIGIT NO SEND . H017$ DISABLE . H015$ CHECK DIGIT SEND . H018$ LEAD DIGIT SEND CHECK DIGIT NO SEND . H025$ + 5 ON ADD ON SUPPLEMENT . H041$ . H026$ ADD A SPACE ON + 5 OFF . H027$ + 2 ON . H042$ ADD A SPACE OFF . H058$ . H028$ ADDENDA REQUIRED ON . H057$ + 2 OFF ADDENDA REQUIRED OFF . H050$ . H049$ ISBN ISBN OFF NOTES: ISBN ON 1.
GROUP-51 SYMBOLOGIES: EAN/UCC-128, CODE 128 . M001$ ENABLE EAN/ UCC-128 . M005$ . M002$ FUNC 1 CHAR SEND . M006$ DISABLE . M003$ FUNC 1 CHAR NOT SEND CODE ID ENABLE . M007$ . M004$ DEFINE EAN 128 CODE ID DISABLE NOTES: DEFINE EAN 128 The first FNC1 character is translated to ]c1, and the second FNC1 character is translated to an ASCII character (scan from Group 41) String format: Setting Procedure: 1: Scan DEFINE EAN128. 2: Scan ASCII Code ( Group 41 ) 3: Scan DEFINE EAN128. CODE 128 .
GROUP-52 GS1 DataBar, LIMITED, EXPANDED . N032$ GS1 DataBar (RSS) - OMNI & STACKED GS1 DataBar ENABLE . N034$ GS1 DataBar CHECK DIGIT SEND . N036$ GS1 DataBar PREFIX SEND . N038$ GS1 DataBar STACKED ENABLE . N033$ GS1 DataBar DISABLE . N035$ GS1 DataBar CHECK DIGIT NOT SEND . N037$ GS1 DataBar PREFIX NOT SEND . N039$ . P024$ GS1 DataBar STACKED DISABLE GS1 DataBar SET ID . N010$ GS1 DataBar LIMITED ENABLE . N012$ GS1 DataBar LIMITED CHECK DIGIT SEND . N024$ GS1 DataBar LIMITED PREFIX SEND .
GROUP-53 FULL ASCII TABLE ( CODE 39 ) CONTROL CODES %U NUL $A SOH $B STX $C ETX $D EOT $E ENQ $F ACK $G BEL $H BS $I HT $J LF $K VT $L FF $M CR $N SO $O SI
GROUP-54 FULL ASCII TABLE ( CODE 39 ) CONTROL CODES $P DLE $Q DC1 $R DC2 $S DC3 $T DC4 $U NAK $V SYN $W ETB $X CAN $Y EM $Z SUB %A ESC %B FS %C GS %D RS %E US SP
GROUP-55 FULL ASCII TABLE ( CODE 39 ) SYMBOLS %L /A %V /C %N %S /F /J %0 %H %Q
GROUP-56 FULL ASCII TABLE ( CODE 39 ) SYMBOLS %P %R %K %M /H /I %G %I > %W /B /G /L %F /Z %J %T DEL
GROUP-57 FULL ASCII TABLE ( CODE 39 ) UPPER CASE ALPHABETS A A B B C C D D E E F F G G H H I I J J K K L L M M
GROUP-58 FULL ASCII TABLE ( CODE 39 ) UPPER CASE ALPHABETS N N O O P P Q Q R R S S T T U U V V W W X X Y Y Z Z
GROUP-59 FULL ASCII TABLE ( CODE 39 ) LOWER CASE ALPHABETS +A a +B b +C c +D d +E e +F f +G g +H h +I i +J j +K k +L l +M m
GROUP-60 FULL ASCII TABLE ( CODE 39 ) LOWER CASE ALPHABETS +N n +O o +P p +Q q +R r +S s +T t +U u +V v +W w +X x +Y y +Z z
GROUP-61 FULL ASCII TABLE ( CODE 39 ) NUMBERS 0 1 2 3 4 5 6 7 8 9
GROUP-62 FULL ASCII TABLE ( CODE 39 ) FUNCTION KEYS $TA F1 $TB F2 $TC F3 $TD F4 $TE F5 $TF F6 $TG F7 $TH F8 $TI F9 $TJ F10 $TK F11 $TL F12 $TM Home $TN End $T+D Enter (Numeric Key) $T+O App
GROUP-63 FULL ASCII TABLE ( CODE 39 ) NAVIGATION KEYS $TO Cursor Right $TP Cursor Left $TQ Cursor Up $TR Cursor Down $TS Page Up $TT Page Down $TU Tab $TV Back Tab $TW Esc $TX Enter $TY BS $TZ Ins $T%K Del
GROUP-64 FULL ASCII TABLE ( CODE 39 ) MODIFIER KEYS $T%M $T%L Alt (Left) break Alt (Left) make*1 $T+E Alt (Right) make $T%N Shift (Left) make *2 $T+I Shift (Right) make $T+K Win (Left) make $T+M Win (Right) make $T%W Ctrl (Left) make *3 $T+G $T+F Alt (Right) break $T%O Shift (Left) break $T+J Shift (Right) break $T+L Win (Left) break $T+N Win (Right) break $T+A Ctrl (Left) break $T+H Ctrl (Right) break Ctrl (Right) make For UK Keyboard Special Character $T+C $T+B Note: *1: When “Alt(Left)
GROUP-65 TROUBLE SHOOTING Our Barcode Scanners are simple to install and use. Most operational issues can be attributed to: INCORRECT INTERFACE CONNECTION INCORRECT CONFIGURATION SETUP POOR BARCODE QUALITY GENERAL PROCEDURES 1. First, make sure the scanner is firmly connected to the host computer, when attached correctly, the scanner will emit one long beep. When the trigger is pressed, LED will flash. 2. Once the power is on, try scanning some sample bar codes from this user’s guide.
GROUP-66 TROUBLE SHOOTING RS232 INTERFACE PROBLEMS Once you read bar code, there is no output on the monitor, the symptoms may be caused by: 1. Have you set the protocol of RS232 like Baud rate, data bits, parity and handshaking etc. of a scanner to match to the PC terminal setting? Solution: reset the above mentioned RS232 protocol of scanner to match to PC protocol. 2. Please check if the cable pinout assignment of bar code match to the pinout assignment of PC terminal? No power supply to the scanner: 1.
GROUP-67 TROUBLE SHOOTING Is the proper symbology enabled? Each bar code symbology can be individually enabled or disabled. It is suggested that you enable only those that you will be scanning, thereby eliminating the possibility of mis reads from the scanning of other symbologies. Does the selected bar code symbology con guration match the bar code(s) being read? Scanned data from each bar code symbology can be restricted to eliminate the scanning of unused symbologies.
APPENDIX 1 DEFAULT TABLE 1 GROUP PARAMETER DEFAULT Computer Type PC-AT 1 Interface (depends on customer order) Setup Code On 2 Reading Mode Trigger 2.2 Bi-color Light Source Green > Red 2.3 Magnetic Switch On Green LED/ Supplement Light (CCD Scanner) On Deactivation Time (CCD & Laser Scanner) 3 Sec Same Code Interval (Laser Scanner) 30 Sec Idle Mode Off Pre-Idle Time 1 Min 2.6 Connection Options BT HID 2.8 Wireless ID Wireless Scanner 2.
APPENDIX 1 DEFAULT TABLE 2 GROUP 16 1 17 2 PARAMETER DEFAULT UPC-A Enable UPC-E Enable EAN-8 Enable EAN-13 Enable MSI Disable Code 39 Enable Code 11 Disable Code 93 Disable EAN-128 Enable IATA Disable GS1 Databar GS1 Databar Stacked GS1 Databar Limited Disable Enable GS1 Databar Expanded GS1 Databar Expanded Stacked PDF417 China Post Code Disable Disable Enable Disable Enable/Disable Enable Check Digits Disable CDV Min Length 11 digits Max Length 48 digits MSI 1 18 2
APPENDIX 1 DEFAULT TABLE 3 GROUP PARAMETER DEFAULT Enable/Disable Check Digits Enable Disable CDV 6 digits 48 digits Min Length Max Length 22 ST/SP; Abcd/abcd, abcd/tn*c, ABCD/ABCD,ABCD/TN*C ABCD/ABCD Start(ST)/Stop(SP) CLSI Format Send On 1 ON/OFF Insert Data Off Off 2 ON/OFF Insert Data Off Off ON/OFF Insert Data Adjacent Required Off Off Off Full ASCII 39 Enable/Disable Check Digits Start/Stop Min Length Max Length Enable Disable CDV Not Send 1 digit 48 digits 23 24 1 25 Code 32 2
APPENDIX 1 DEFAULT TABLE 4 GROUP 30 1 31 2 3 PARAMETER DEFAULT Enable/Disable Enable Check Digits Send Lead Digits Send Add a space Off Addenda required Off +5 On/Off Off +2 On/Off Off ISSN On/Off Off ISBN Off Enable/Disable Enable Code ID Disable Func 1 Char Send Not Send Enable/Disable Enable Check Digits Disable CDV Min Length 5 digits 48 digits Max Length PDF417 Enable/Disable GS1 Databar GS1 Databar Check Digit 32 Disable Disable Not Send GS1 Databar Prefix Not
APPENDIX 2 Cable Pin Assignment INTERFACES: 1. TTL, Wand Emulation 1.1 ) AMP (D-Sub 9Pin): Pin 2 7 9 Signal Data GND +5VCC 1.2 ) Din 5 male (240 degree): Pin 1 2 3 4 5 Signal + 5VCC Data GND N/A N/A 2. Keyboard Interface: Type of connector: 2.1 ) PS/2 Mini Din6 Female: Pin 1 2 3 4 5 6 Signal PC Data NC GND +5VCC PC-Clk NC 2.
APPENDIX 2 Cable Pin Assignment 2. Keyboard Interface: Type of connector: 2.3) PC-AT: Din 5 Male: Pin 1 2 3 4 5 Signal KB-Clk KB-Data NC GND +5VCC 2.4) PC-AT: Din 5 Female: Pin 1 2 3 4 5 Signal PC-Clk PC-Data NC GND +5VCC 3.RS232 Interfaces: 3.1) DB9F Signal Pin 2 TXD(Out) RXD(In) 3 5 GND CTS(In) 7 8 RTS(Out) 9 +5VCC 3.
APPENDIX 3 BAR CODE TEST CHART DENSITY NARROW mm[mil] WIDE mm[mil] CHAR.GAP mm[mil] N/W RATIO MEDIUM DENSITY 0.25(10) 0.625(25) 0.25(10) 1/2.
APPENDIX 3 BAR CODE TEST CHART DENSITY NARROW mm[mil] WIDE mm[mil] CHAR.GAP mm[mil] N/W RATIO LOW DENSITY 0.33(13) 0.825(32.5) 0.33(13) 1/2.
