Mini Wireless Barcode Reader Quick Guide Full user’s manual is available on the enclosed CD.
FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
OUT OF THE BOX INTRODUCTION Trigger Scanner Tools LED Indicator Mini Wireless Barcode Reader CD Mini USB port (w/ Protective Cover) Exit Window NUMERIC BARCODES Mini Wireless Barcode Reader *1* *2* *3* *4* *5* Quick Guide Quick Guide 1 2 3 4 5 Quick Connection Card USB Charger Cable Hand Strap -3- SPECIFICATIONS Light source Scan rate Sensor Resolution PCS Housing Profile Working Hours Charge Time Coverage 625nm visible red LED 240 scans/sec Linear CMOS sensor 5mil/ 0.
GETTING STARTED BEEPER INDICATION To scan a barcode, make sure the aiming beam crosses every bar and space of the barcode. Single long beep Single beep Single short beep Two beeps Two short beeps Five beeps Three beeps Three short beeps CHARGING THE BATTERY Host USB A Scanner Mini USB 1. Flip open the mini USB port on the scanner. 2. Insert the mini USB connector into the port on the scanner and USB A connector into a USB port on the host PC.
GETTING CONNECTED PINCODE SETUP There are two modes of wireless communication: . E042$ *.E042$* BT mode - SPP 1. Press the trigger for 1 second to activate the scanner. 2. Scan [DISCONNECT] 3. Scan [BT mode - SPP]; the scanner will emit 8 beeps. 4. Select “Wireless Scanner” from discovered device list. The default pincode is “1234”. 5. Open serial communication software with com port (see Device Manager) properly set up. 6. The scanner will beep twice to verify the connection. . E043$ *.
NUMERIC BARCODES *1* *2* *3* *4* *5* -9- 1 6 2 7 3 8 4 9 5 0 *6* *7* *8* *9* *0* - 10 -
POWER OFF TIMEOUT The timeout before automatic power-off to save power. . B017$ *.B017$* *.B018$* *.B019$* *.B020$* *.B021$* 1 MIN . B018$ 3 MIN . B019$ 5 MIN . B020$ 10 MIN 1. Pair with the scanner via [BT mode - SPP]. (page 7) 2. Install Bluetooth Connect.apk and enter the program. 3. Enable [BluetoothConnect] in the Language & Keyboard setting window and choose [BluetoothConnect] as Input Method. 4. Click [Connect] and you will be able to connect the scanner.
GENERAL SETTINGS READING MODE . A001$ . F002$ DEFAULT TRIGGER . P023$ . F003$ RESET TOGGLE . A007$ . F001$ CHECK VERSION FLASH BEEPER . F005$ CONTINUOUS . F012$ BEEP OFF .
KEYBOARD LAYOUT . C010$ . C014$ ENGLISH (USA) ITALIAN ENGLISH (UK) CZECH (QWERTY) FRENCH CZECH (QWERTZ) . C018$ . C017$ . C022$ . C012$ . C021$ . C011$ GERMAN HUNGARIAN SWISS JAPAN (106 key) . C009$ . C016$ . C013$ .
ENABLE SYMBOLOGIES . G010$ . A002$ ENABLE ALL CODE CODE 93 . N017$ . K010$ CODE 32 IATA . L014$ . L010$ UK PLESSEY TELEPEN . L001$ . N032$ MSI GS1 DATABAR INDUSTRIAL 2 OF 5 GS1 DATABAR LIMITED MATRIX 2 OF 5 GS1 DATABAR EXPANDED . N010$ . N001$ . N026$ .
TERMINATOR TEST BARCODES . D012$ CR . D011$ Code 39 CODE-39 TEST LF Interleaved 2 of 5 . D013$ CR + LF 9876543210 Code 128 . D010$ NONE 12345678 . D015$ SPACE EAN .
