STOP DON'T TAKE ME BACK TO THE STORE. LOOK FOR THE TOLL-FREE "HELP" TELEPHONE NUMBER. LISTEN AS THE EXPERTS TALK YOU THROUGH THE PROBLEM. For immediate answers ta your questions regarding operation, missing parks or installation, call: Southwestern Bell Freedom Phone® Retail Sales Help Line at 1-800-366-0937 Monday Friday 8:30 am. 9:00 p.m. EST Saturday 8:30 a.m. 12:30 p.m. EST HTTP: // www. swhireedomphone. com SOUTHWESTERN BELL FREEDOM PHONE 7475 N. GLEN HARBOR BLVD.
PLEASE READ IMPORTANT SAFETY INSTRUCTIONS BEFORE USE. Congratulations! You have purchased a 900M Hz Cordless Telephone with Call Waiting Caller ID and an All Digits) Answering System that has been manufactured to the highest standards of SOUTHWESTERN BELL FREEDOM PHONE ® Retail Sales. Its "DIRIGIBLE PLUS™ circuitry combines noise filtering with aisle of the art technology that reduces background noise from your telephonic conversations.
Safety Instructions for Batteries Handset Battery Pack CAUTION: Use only a Southwestern Bell Freedom Phone® approved battery pack in the handset of your FF2150 Cordless Telephone. To reduce the risk of fire or injury, always do the following when replacing, discarding or charging betters. When handling the batteries, be careful Lotto short the battery with conducting materials such as rings, bracelets. aad keys.
Southwestern Bell Freedom Phone FF2150 Cordless Telephone Contents Subject Safety Instructions, Traits of Cordless Telephones. Bax Content INSTALLATION... Preliminary Preparation. —) Telephone Line Installation outlast Outlet Battery Back; Desk ar Table Installation Wall Moving Handset Battery Charging To Replace Batteries Initial Setup Caller ID & Remote Access code TELEPHONE OPERATION...
Base Diagram BASE CONTROLS: This diagram shows the controls of the FF2150 Base. BATTERY LOW LED HANDSET GUIDE Ix uses CHARGE MESSAGE VOLUME Lip COUNTER UPTOWN Antenna ERASE. REPEAT J PAGE MEMO §TOP VOICE MENU REAR VIEW Apa SEE POKER JAX FINE JACK RE MISMATCH Traits of Cordless Telephones A. Cordless telephones offer convenience and mobility during telephone conversations. The use of cordless telephones is dependent upon ihe availability of AC power.
Installation Box Contents Before installing your phone, check the shipping carton to be sure you have the following: + Base Unit + Short and Long Telephone Line Cord + Remote Access Card » Handset with Rechargeable Battery Notes: + Quick Installation Guide «+ AC Adapter with Cord + Owner's Manual » Wall Mounting Bracket Installation (Cont.) Table/Desk Installation A.
Installation (Cont.) E, Connect the AC adapter into the back of the unit and plug the either end to the 110/120 volt outlet. F. The Message counter wil show AA" flashing. The unit is checking its memory, and you should not press any buttons. 6. When you fug in your unit for the first time, it will take approximately 19 seconds for the unit to check its memory. When the memory check is complete, your system will announce “Unit Ready" and will reset 1 answer incorporating calls.
Caller ID Setup/Telephone Operation Fo Set Area Code Nate : In order for the Caller ID Redial feature to work properly, you must set your local area code. TE (0 uy 203 AREA CODE 5 1. Enter your 3-digit local area code, using the handset keypad 2. After selecting the third digit, press the “MEM” bunion to confirm the displayed area code, The wit will begin to set the remote access PIN code.
J Telephone Operation (Cont.) 5 1, remove the belt clip from the Note: If you experience difficulty with placing or receiving calls, the lost security code may be the cause of the problem. When this occurs, the handset can no longer communicate with its base.
Telephone Operation (Cont.) Scratchpad Memory The FF2150 also functions as a scratchpad, If you want to save a displayed telephone number (up 10 16 digits) into speed dial memory: rT ne ul 555 1234 1. Press the "MEM" button on the handset. The display will show “LOCATION ? x”, with "x" representing the first empty memory location. SEE ie “fs LOCATION © & 2. Press the "MEM" button again to confirm that you want io save the telephone number to that particular memory location number.
Telephone Operation (Cont.) 3. Press the "CALLS" button. The number will scroll across the screen from left to right as it is dialed. TALE ne ug 5551234 Call Timer 1. The LCD will display the call duration timer 10 seconds after a call is begun. 200% 10 TALK Qa 2. During the call, the base message counter will show "In". For example, if the call is made through the handset, the handset display will show the call timer, and the bse message counter will show "fn" 3.
Telephone Operation (Cont.) LCD/LED INDICATIONS BASE LED STATUS INDICATIONS IN USES OFF -Not in use CHARGE ‘Handset off cradle ON ~In TALK mods “Battery being charged PAGE key pressed MESSAGE ON “Unit in Answer Ready Mode COUNTER -AC power consented OFF “Unit in Answer Off mode -AC power disconnected a Unit in Announce Only Mode BATTLE ON Low 9 volt battery OFF -6 volt basketry installed while AC power connected HANDSET LED STATUS INDICATIONS NEW | FLASHING | -New Caller ID information is in CALL memory.
bo Answering System Operation (Cont.) Recording Outgoing Greeting Your system comes with a prerecorded outgoing greeting; “Hello, We are not available now, please leave your name and number after the beep”. The prerecorded announce only greeting is “Hello, Our machine cannot accept messages. Please call again”. You can record both a personalized Answer On (Answer Ready) and an Announce Only greeting. To record an Answer On greeting, make sue you are in the Answer On mode (the message counter will be Tit).
Message Playback Incoming Messages When the answering system is on and is ready to answer calls, the base display will show the number of new messages and the total number of messages in memory (up 1099). Note: “The machine hangs up and resets 1o answer the next call in the following cases: the cater hangs up, the message length exceeds 60 seconds, there are more than 7 seconds of silence or there is a steady tone (dial tone) for 7 seconds. The FF2150 can record up to 15 minutes of incoming messages.
Tone Remote Operation To access answering functions from an outside Heine, you will need to enter the two digit remote access security/pin code (see page 12). To set a new or to cheek the security coder 1. When the current time/day is displayed on the handset, press the "CH" button for & second. 2. The current set language will display on the handset. Press the "MEM" key to confine. 3. The current set area code will display on the handset. Press the "MEM key to confirm the area code.
Caller ID Operation (Cont.} To Store a Caller ID Record ta Speed Dial Memory Note: ~ You can store a Caller ID record from the handset to speed dial ornery. I. When the handset display shows the current time/day, press the "Hv" bunion select the Caller ID record you want to store to speed dial memory. © Anne CALL ¢ HU o03-55623 SHOESHINE 2. Press the "MEM" button on the handset. i wil 3. The display will show “LOCATION 7x", with "x" representing the first empty memory location. ns pHi LOCATION 7 & 4.
Caller ID Operation (Cont.) Calder ID Erase To Erase s Single Cal 1. When the handset display shows the current timed day, press the "a>" or button to select the Caller ID record you want to erase. 2. Press "DEL button to erase the call displayed; the display will show "ERASE?" an the bottom line. [ET eho ve 203-555-1234 ERASE 7 4. Press "DEL" button again; the Caller ID record will be erased and the display will show the next call message.
Lt Answers to Commonly Asked Questions Q. Y con't get a dial tone. What Your phone may have lost its digital security code and needs to be reset. Refer to the "To Reset" procedure un page 26. ©. My answering system won't work, ‘What You may have had a power failure and zed to serer your machine. Refer to the "To Reset Unit" procedure on page 26 or "To Turn System On" on page 22. Q. How do I erase the incoming messages to make room for more? A. Your unit automatically saves messages unless you erase them.
Troubleshooting Guide 1£ you have followed the instructions in this manual, and have difficulty operating your Southwestern Belt Freedom Phone® Cordless Telephone, local the PROBLEM in the loft column below. Check the corresponding POSSIBLE CAUSE and CORRECTIVE ACTION columns to locate and remedy the problem, Lo or receiving calls security code. The handset can no longer communicate with its base.
| Troubleshooting Guide (Cont.) 1 OFF" mode. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Answering system | You may have had 2 Proceed with a unit reset (page 26). will not operate. | power failure. BAT LOW Battery needs to be Install a fresh 9 volt battery. LED ON installed or replaced. To answer Unit Is in the "ANSWER | Check to verify the base display shows "A" of the message count. If not, press the ANSWER ON/OFF button to tem the unit on, until you hear “Answer On".
Troubleshooting Guide {Cont.) PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Your telephone rings but the FF2150 doesn't stow any Caller ID records. The telephone line is riot connected properly 10 the unit. Connect the telephone line into the back of the unit. Check with your local telephone company to be sure Caller ID service is being provided on your telephone inc, Also, if you pick up the phone before the first complete ring, the caller information will not be completely received.
Service According to FCC regulations, this equipment, which has been certified and registered by the FCC, may only be repaired by authorized persons. If repairs or adjustments are made by an unauthorized person, the FCC certification may be voided. Should you encounter any problems, please call the Southwestern Bell Freedom Phone toll-free Customer Help Line for assistance: 1-800-366-0937, Mandy Friday &:30 am 9:00 pm, and Saturday 8:30 am 12:30 pm.
PLAYBACK/OPERATION: Press and release PLAY button. Unit will playback messages in the order they were received. The set, date/time will be played at the beginning of each message. . After last message is played, you will hear “No more messages. Press and hold the ERASE button to erase all messages”. . Press ERASE button for 2 seconds. You will hear "Press ERASE button again to erase all messages." Press ERASE button again to erase all messages. .
INSTALLATION Locate the FF2150 near a standard AC power outlet and a modular telephone jack. Lift the battery compartment door. Install ene 9-coll battery (not included} inch the compartment. Insert one end of the TELEPHONE LINE CORD into 2 modular wall jack aud the other end into the back of the base. Insert the small fug on the end of the AC adapter into the POWER connection jack at the back of the BASE. Plug the AC adapter into a 110/120V wall outlet. IMPORTANT.
