Model 750 Illustrated Installation Instructions Contractors Wardrobe ® DESIGNERS • MANUFACTURERS 26121 Avenue Hall • Valencia, CA 91355 • (661) 257-1177 • Fax: (661) 257-4907 Toll Free: (800) CW-DOORS • (800) 293-6677 • www.CwDoor.
15 Illustrated Parts Breakdown (IPB) Drawing Model #750 (For shower head nozzle on right) 19 22 A - Note: The Handle (#14) is installed in this location but is not displayed in the drawing. See Step 13 for installation instructions of the handle. 9 23 7 17 1 10 11 7 23 7 17 22 15 10 20 5 13 9 23 15 16 18 23 17 3 A 13 15 12 19 22 16 18 23 22 14 15 6 8 3 19 23 7 20 11 23 21 22 4 8 23 2 No.
No. Qty. Description In this instruction booklet we will walk you through the installation of your new shower door. (#1) 1 Header - #750 (approx. 1” oversized) DO NOT REMOVE your old shower door until you check that your new shower door kit is the right size for your shower and that all the proper parts are in the box or hardware bag. NOTE: The Header (#1) and Curb (#2) are shipped 1” oversize, so you will need to cut each to fit. (#2) 1 Curb (approx.
A. Using the Tape Measure, measure between right and left walls along the flattest part of the shower sill. B. Round off both ends of the Curb (#2) and Wall Jambs if necessary. Figure 1 B. Drill center hole 3" C. A Center Curb (#2) on sill and mark position with Pencil Figure 2 C. Lay the Curb (#2) on the shower sill with the sloping face of the Track towards the inside of the shower. Center the Curb (#2) on the shower sill, and secure it in position with strips of Duct Tape.
G. Remove the Curb (#2). Gently center punch the three holes along each Wall Jamb (#3). On ceramic tile be very careful and only tap the punch lightly enough to nick the tile surface but not crack the tile. H. Use the 3/16" Drill Bit and drill holes into the wall for both Wall Jambs (#3). When finished, be sure to clean the shower sill of any debris from drilling. I. Insert a Screw Anchor (#22) into each of the six holes. STEP 5 STEP 7 A.
STEP 8 Measuring and Installing the Header A. Locate the Header (#1) and two #6 x 1/4" "B"-Point Screws (#15). B. Measure the distance, wall to wall, at the top of the Wall Jambs (#3). Cut the Header (#1) 1/16" shorter than this measurement to allow for clearance. C. Install the Header (#1) over the ends of the Wall Jambs (#3). Stand in the shower for the next steps. D.
STEP 11 A. Locate the Guide (#4) and one #6 x 3/8" PH SMS Screw (#21). Standing inside the shower, position the Guide (#4) on the Curb (#2) exactly midway between the Wall Jambs (#3). The Guide (#4) will lay flush on the Curb (#2). B. Using the hole in the Guide (#4), drill a 1/8" hole into the Curb (#2). C. B. Position Handle midway on Door Panel B.
STEP 15 Cleaning and Removing the Door Panels The enclosure Door Panels (#5 and #6) are not designed to be removed once they are installed. However, inconvenient areas that you may want to clean, such as the overlap between the doors, can still be reached for cleaning. A. Carefully remove all the hardware from door. This will enable you to slide the glass Door Panels (#5 and #6) in either direction to clean them thoroughly. B. Clean the glass and Curb (#2) with a mild, nonabrasive cleaner. C.