User's Manual

ManualsBrandsControl4 ManualsComputer equipmentTabletop Touchscreen

Wi-Fi Limited Module

Integration Instructions

Model: 040-00460a

This module has been granted limited modular approval for use in the C4-T4 Series of Automation Controllers.

This device is for internal use only and is NOT sold to 3

parties. Use of this device on products other than those

listed below will require additional certifications.

• The host product with the module installed must be evaluated for simultaneous transmission

requirements.

• The user manual for the host product must clearly indicate the operating requirements and conditions

that must be observed to ensure compliance with current FCC/IC RF exposure guidelines.

The Module must only be used in the following device and antenna combinations

DEVICE

ANTENNA PORT

ANTENNA MODEL

C4-T4IW10-XX*

Antenna 0

1005097

Antenna 1

1005098

C4-T4IW8-XX*

Antenna 0

1005095

Antenna 1

1005096

C4-T4T10-XX*

Antenna 0

1005180

Antenna 1

1005179

C4-T4T8-XX*

Antenna 0

1005178

Antenna 1

1005179

• - XX is a unit color identifier (Black or White)

• A label must be affixed to the outside of the host product with the following statements:

“Contains FCC ID: 2AJACT4TS”

“Contains IC: 7848A-T4TS”

The final host/module combination may also need to be evaluated against the FCC Part 15B criteria for

unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.

If the final host/module combination is intended for use as a portable device (see classifications below) the host

manufacturer is responsible for separate approvals for the SAR requirements from FCC Part 2.1093 and RSS-102.

The module incorporates a MuRata radio module with a single transciever output that connects to an RF

switch for diversity. The switch drives two MHF 4L coaxial sockets to which a the antennas can be attached.

Summary of content (6 pages)

PAGE 1
Wi-Fi Limited Module Integration Instructions Model: 040-00460a This module has been granted limited modular approval for use in the C4-T4 Series of Automation Controllers. This device is for internal use only and is NOT sold to 3rd parties. Use of this device on products other than those listed below will require additional certifications. • The host product with the module installed must be evaluated for simultaneous transmission requirements.
PAGE 2
Signal and power connector Connect signal and power through Novastack 35-P board connector details: I-PEX Connectors: 20709-050E-01 0 CONN, 50PIN PLUS 2 POWER RECEPTACLE 0.7MM HEIGHT 0.35MM PITCH Drawing: Reference A B C D E F Dimension in mm 8.40 9.42 10.92 10.75 9.70 11.
PAGE 3
Receptacle pinout: Device classifications Since host devices vary widely with design features and configurations, module integrators shall follow the guidelines below regarding device classification and simultaneous transmission and seek guidance from their preferred regulatory test lab to determine how regulatory guidelines will impact the device compliance. Proactive management of the regulatory process will minimize unexpected schedule delays and costs due to unplanned testing activities.
PAGE 4
Mobile: (§2.1091) (b) —A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. Per §2.
PAGE 5
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. FCC Modular Usage Statement Note 1: This module certified complies with RF exposure requirements under mobile or fixed condition; this module is to be installed only in mobile or fixed applications.
PAGE 6
Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en oeuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.