Lighting Design Guide
Table Of Contents
- Legal notices
- Introduction
- A complete control solution
- Comprehensive control options
- Enhanced user interface customization
- Integration simplicity
- Best-in-class dealer tools and support
- Wireless Lighting components
- Panelized Lighting components
- System design types
- Specifying a system
- Control4 Wireless Adaptive Phase Dimmer
- Control4 Wireless Keypad Dimmer
- Control4 Forward Phase Dimmer
- Control4 Wireless Switch
- Control4 Wireless Configurable Keypad
- Control4 Wireless Fan Speed Controller
- Control4 Wireless 0-10V Dimmer
- Control4 Auxiliary Keypad
- Control4 Wireless Outlet Dimmer and Switch
- Third-party products
- Control4 5-Slot and 2-Slot Panels
- Control4 8-Channel 0-10V Dimmer
- Control4 8-Channel Dimmer
- Control4 8-Channel Relay
- Control4 8-Port Ethernet Switch
- Control4 Bus Ethernet Gateway
- Control4 Bus Power Supply (48V)
- Control4 Decora Wired Keypad
- Control4 Square Wired Keypad
- Control4 Terminal Blocks
- Control4 4-Channel Bus Dry Contact Input Module
- Lighting project checklist
- Wireless Lighting application
- Panelized Lighting application
51
Control4 8-Channel 0-10V Dimmer
Control4 8-Channel 0-10V Dimmer
(C4-DIN-8TV-E)
The Control4® 8-Channel 0-10V Dimmer controls up to eight
0-10V dimmable fluorescent ballasts or LEDs. Each channel
can control up to 50 ballasts. Individual 0-10V lights can be
programmatically tied to a corresponding channel on an
8-Channel Relay module for on/o control of the ballast or
LED when needed. Alternatively, the Control4 8-Channel 0-10V
Dimmer module also has eight low-voltage outputs for triggering
external power relays.
Product features
• 110V to 277V operation.
• IP controlled.
• Sync up to 100mA per channel for control of up to 50 ballasts
or source up to 25mA per channel for control of up to 12
ballasts.
• Channel buttons allow for toggling on/o or ramping up/down
a load.
• Channel status LEDs indicate load status.
• Module override button allows toggling between the module
override scene and all channels o or setting the module
override scene to current channel levels.
• Module status LED indicates if module power is on with
normal operation or o.
• Auxiliary override connection allows a standard line-voltage
toggle switch to control the attached lights before the control
system is installed or in case the controller malfunctions.
Included
• 8-Channel 0-10V Dimmer
• 8-Channel 0-10V Dimmer Installation Guide
• 8-Channel 0-10V Module Wiring Guide
Installation notes
• Prior to installation, determine whether on/o control of each
0-10V load is required in addition to the 0-10V control. If it is,
determine whether a corresponding channel on a Control4
8-Channel Relay Module will be used, or whether an external
power relay (such as a Leviton Power Pack Relay) will be used.
• In the US and Canada, modules must be installed in a Control4
2-Slot or 5-Slot panel to meet regulatory requirements.
Outside of the US and Canada, modules may be installed in
either a Control4 panel, an o-the-shelf DIN rail panel, or a
custom DIN rail enclosure per local regulatory requirements.
• If using a Control4 panel, install the Terminal Block for the
0-10V Dimmer (C4-DIN-TB-PO) following the instructions
in the Terminal Block Installation Guide and in the location
defined by the Composer Pro Panel Reports. The Terminal
Block should be installed in the lower half of the specified
Terminal Block slot area. Terminal block installation should be
done prior to rough-in so that the electrician can terminate
wires during the rough-in.
• Module must be installed in a climate-controlled area to
prevent overheating.
• For full installation instructions and warnings, see the 0-10V
Dimmer Installation Guide and 0-10V Dimmer Wiring Guide.