User's Guide

Use the remaining content in this section to learn more about some of these
connection options.
Use Video Sense Loops
Video sensing can enhance the ability to sense the power state of a device,
such as whether the device is “on” or “off.” If you need to add video signal
sensing capabilities for a video device (such as a TV, VCR, DVD player, etc.),
connect one of the device’s composite Video Out ports to a Home Controller
Video Sense In port. Then, use the companion Video Sense Out port (where
available) for the device’s video out as needed.
For Video Sense only (no loop-through), connect a device’s Composite Video
Out port to one of the two Video Sense In ports.
Use Pluggable Terminal Block Connectors
For the Contact and Relay ports, the Home Controller makes use of a
pluggable terminal block connector—a removable plastic part to lock in
individual wires. This connector is included.
To connect a device to the Pluggable Terminal Block:
1. Insert one of the wires required for your device into the appropriate opening
in the Pluggable Terminal Block you reserved for that device (refer to
Table 1 on page 2).
For example, if you were adding a motion sensor, you would connect its wires to the
following Contact openings: power input to +12V output signal to SIG, and ground
connector to GND. See the sections that follow for instruction on connecting the
various protocols.
2. Lower the openings latch until it locks the wire in place.
3. Repeat Steps 1-2 for all wires required for your device.
NOTE: When you connect dry contact closure devices, such as door
switches, connect the switch between +12V (Power) and SIG (Signal).
Connect to the Contact Port
The Home Controller provides one contact port as a subset of the pluggable
terminal block provided. See the following figures to determine how to connect
the device to a contact port.
NOTE: Before using a device in the contact port, attach the ferrite
(supplied) to the cable.
Figure 1: Contact Port for Voltage Source (i.e. Motion Sensor)
Figure 2: Contact for Dry Contact (i.e. Door Contact Sensor.
Figure 3: Connect Contact for Self Powered Voltage Source Device
Connect to the Relay Port
The Home Controller provides one relay port as a subset of the pluggable
terminal block provided.
For most applications, you attach one wire to the common terminal and the
other to the normally open terminal.
The relay switches closed when the relay is activated.
The Home Controller can support applications that require a normally closed
contact.
Connect the Serial Ports
The Home Controller provides two DB9-style serial ports. Connect a device to
the Home Controller, like a monitor or TV, by aligning the pins and tightening
the screws.
Figure 4: Connect to DB9 Serial Port
Set Up IR Emitters or IR Blaster
Your system may contain third-party products that are controlled with IR
commands (usually through remote controls). To provide a way for the Home
Controller to control a device that only recognizes IR commands, complete one
of the following setups: IR Emitters or IR Blaster.
IR Emitters
1. Plug the 3.5 mm connector end of one of the 6 IR stick-on emitters provided
into an IR Out port on the Home Controller.
2. Place the stick-on emitter end over the IR receiver on the media player, TV,
or other target device to transmit IR signals from the Home Controller to the
target.
IR Blaster
In addition to IR emitters, the Home Controller is also equipped with an IR
blaster, which is located just under the front LEDs. To use the blaster instead of
an IR emitter:
1. In Composer, connect IR Out #6 of the Home Controller to the IR In of the
device you wish to control.
2. Do not physically connect anything to IR Out Port #6.
3. Test and verify that the Home Controller is positioned in such a way that the
blaster can reach the device you wish to control.
Set up External Storage Device
You can store and access media from an external storage device, such as a
network hard drive or USB memory device. Simply plug the USB drive into one
of the USB ports and configure or scan the media from Composer.
Regulatory Compliance
North America
This product complies with standards established by the following regulatory
bodies:
• Federal Communications Commission (FCC)
• Industry Canada
• Underwriters Laboratories Inc. (UL)
IMPORTANT! Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
Federal Communications Commission (FCC)
FCC ID: R33C4HC3001
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada
This Class B digital apparatus complies with Canada ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Underwriters Laboratories Inc. (UL)
(pending)
CE Declaration of Conformity
Product: Home Controller HC300
The undersigned hereby declares, on behalf of Control4 Corporation, that the
above-referenced product, to which this declaration relates, is in conformity
with the provisions of:
• Council Directive 89/336/EEC (May 3, 1989) on Electromagnetic Compati-
bility
• Council Directive 1999/5/EC (Mar 9, 1999) on Radio & Telecommunication
Terminal Equipment (R&TTE)
• Council Directive 73/23/EEC (Feb. 19, 1973) on Low Voltage Equipment
Safety
• Council Directive 93/68/EEC (Jul. 22, 1993) Amending Directives 89/336/
EEC and 73/23/EEC
and has been tested to the requirements of, and shown to be in compliance
with, the following requisite standards:
• EN 301 489-1 V1.4.1—Electromagnetic compatibility and Radio spectrum
Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services–Part 1 Common technical requirements.
• EN 301 489-17 V1.2.1—Electromagnetic compatibility and Radio spectrum
Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 17: Specific conditions for 2.4 GHz wideband
transmission systems and 5 GHz high performance RLAN equipment.
• AS/NZS CISPR 22: 2002—Information Technology Equipment—Radio dis-
turbance characteristics.
• EN 300 328-2 V1.4.1—Wide band transmission systems; data transmission
equipment operating in the 2.4GHz ISM band. Harmonised EN covering
essential requirements under Article 3(2) of the R&TTE Directive.
• AS/NZS 4771: 2000—Spread Spectrum Equipment using 900MHz, 2.4GHz
and 5.8GHz bands.
• IEC 60950-1: 2001 (1st Edition) and/or EN 60950-1: 2001—Information
Technology Equipment—Safety with national and group differences in
accordance with CB Bulletin No. 109A December 2005: AS/NZS 60950-1:
2003.
The Technical Construction File required by these Directives is maintained at
the corporate headquarters of Control4, Salt Lake City, Utah, U.S.A.
Signed,
Paul E. Nagel—Vice President of Engineering, ________, 2007
Recycling
For information on recycling, please go to www.control4.com/
recycling
About This Document
Copyright © 2007 Control4 Corporation. Control4 and the Control4 logo are
registered trademarks of Control4 Corporation. All trademarks are properties of
their respective owners. Part Number: 200-00031 Rev A - Draft 4
IR Out (6)—3.5 mm jacks for up to 6 IR output transmitters.
See “Set Up IR Emitters or IR Blaster” for more information.
12V
Provides power for small devices
SIG
Signal input
GND
Return path
12V
Provides power for small devices
SIG
Signal input
GND
Return path
Connection Options
SIG
Signal input
GND
Return path
European Contact Information
Control4 UK Limited
Unit 3, Green Park Business Centre
Sutton-on-the-Forest, York
YO61 IET, United Kingdom
[phone]
[e-mail]
United States Contact Information
Control4 Corporation
11734 S. Election Road, Suite 200
Salt Lake City, UT 84020-6432, USA
Tel [phone]