User's Manual

7” TABLE TOP
TOUCH SCREEN
Installation
Guide
Model
• C4-TST7-EG-B (7” Tabletop Touch Screen, WiFi and Ethernet)
What’s in the Box
Carefully unpack the contents from the box and make sure the following
items are included in the box. If any item is missing or damaged, please
contact your Control4-authorized reseller immediately.
•
7” Tabletop Touch Screen (C4-TST7-EG-B)
• AC power cord and power adapter
• 7” Tabletop Touch Screen Installation Guide (this document)
Accessories
• Control4 Power Over Ethernet Injector (AC-POE1-B)
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Install in accordance with the manufacturer’s instructions.
8. Install in accordance with all national and local electrical codes.
9. This product is also designed for IT power systems with phase-to-phase
voltage 120V or 240V.
10. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
11. Only use attachments/accessories specified by the manufacturer.
12. If applicable, unplug this apparatus during lightning storms or when
unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-sup-
ply cord or plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning! The touch screen must be protected by an external circuit
breaker or a fuse rated at 6A maximum when used in Europe.
Avertissement! To reduce the risk of fire or electrical shock, do not
expose this apparatus to rain or moisture.
Warnung! Die Berührungseingabe muß durch einen externen Circuit
breaker oder eine Sicherung geschützt werden, die am Maximum 6A
veranschlagen wird, wenn sie in Europa verwendet wird.
Warning! To reduce the risk of fire or electrical shock, do not expose
this apparatus to rain or moisture.
Avertissement! Pour réduire le risque du feu ou de choc électrique,
n'exposez pas cet appareil à la pluie ou à l'humidité.
Warnung! Um die Gefahr des Feuers oder des elektrischen Schlages
zu verringern, setzen Sie diesen Apparat nicht Regen oder
Feuchtigkeit aus.
Warning! To avoid bodily harm, always contact a Control4-
authorized reseller for assistance if any repair or adjustment is
required.
Avertissement! Pour éviter des dommages physiques, contactez
toujours un revendeur de Control4-authorized pour l'aide si n'importe
quelle réparation ou ajustement est exigée.
Warnung! Um körperlichen Schaden zu vermeiden, treten Sie immer
mit einem Control4-authorized Reseller für Unterstützung in
Verbindung wenn irgendeine Reparatur oder Justage angefordert
wird.
Warning! Do not place unit near sources of heat or expose to direct
sunlight for an extended period of time.
Avertissement! Ne placez pas l'unité près des sources de chaleur
ou exposition pour diriger la lumière du soleil pendant une période
prolongée.
Warnung! Setzen Sie Maßeinheit nicht nahe Quellen der Hitze oder
des Exposés, um Tageslicht während eines ausgedehnten
Zeitabschnitts zu verweisen.
Warning! Do not stare at the light or proximity sensor. Looking at
these sensors for extended periods of time may cause damage to the
eyes.
Avertissement! Ne regardez pas fixement la lumière ou le capteur
de proximité. Regarder ces sondes pendant des périodes prolongées
peut endommager les yeux.
Warnung! Starren Sie nicht entlang des Lichtes oder des
Annäherungssensors an. Das Betrachten dieser Sensoren nach
ausgedehnten Zeitabschnitten kann Beschädigung der Augen
verursachen.
Important! Do not use pens or sharp objects to navigate or make
selections on the screen. To select an item or scroll through a list, use
your fingertip.
Important!
N'employez pas les stylos ou les objets pointus pour
diriger ou pour faire des choix sur l'écran. Pour choisir un article ou un
rouleau par une liste, employez votre bout du doigt.
Wichtig! Benutzen Sie nicht Federn oder scharfe Gegenstände, um
oder Vorwähleren auf dem Schirm zu bilden zu steuern. Um ein
Einzelteil oder eine Rolle durch eine Liste vorzuwählen, benutzen Sie
Ihre Fingerspitze.
Important! Improper use or installation can cause LOSS/DAMAGE
OF PROPERTY.
Important! L'utilisation ou l'installation inexacte peut causer LOSS/
DAMAGE DE PROPRIÉTÉ.
Wichtig! Unsachgemäßer Gebrauch oder Installation können LOSS/
DAMAGE DER EIGENSCHAFT verursachen.
Important! Using this product in a manner other than outlined in this
document voids your warranty. Further, Control4 is NOT liable for any
damage incurred with the misuse of this product. See “Limited 2 Year
Warranty.”
Important! Utilisant ce produit en quelque sorte autre que décrit
dans ce document vide votre garantie. De plus, Control4 n'est pas
responsable d'aucun dommage encouru avec l'abus de ce produit.
Voyez que « Limited 2 Year Warranty. »
Wichtig! Das Verwenden dieses Produktes in gewissem Sinne
anders als umrissen in diesem Dokument hebt Ihre Garantie auf.
Weiter ist Control4 NICHT für irgendeine Beschädigung
verantwortlich, die mit der Fehlanwendung dieses Produktes
genommen wird. Sehen Sie, daß “Limited 2 Year Warranty”.
Requirements
To install the touch screen, you need the following:
•
Control4 controller, fully installed and configured.
• (Optional) An amplifier or amplified speakers.
• (Optional) Any RCA cables required to connect the touch screen and the
amplifier or amplified speakers.
• For an Ethernet installation that uses POE Power:
• Ethernet network installed and available that includes a gateway/router/switch
• Access to the Control4 PoE Injector (model #AC-POE1-B) or an 802.3af
compatible PoE Ethernet switch.
• Two Ethernet CAT 5 cables: (1) one that will run from the Ethernet gateway/
router/switch to the PoE injector/switch and (2) one that will run from the PoE
injector/switch to the 7” touch screen.
• For an Ethernet installation that uses AC Power:
• Ethernet network installed and available that includes a gateway/router/switch
• Access to a power outlet.
• One Ethernet CAT 5 cable to run from the Ethernet gateway/router/switch to
the 7” touch screen.
• For a WiFi installation:
• Wireless network (WiFi 802.11b/g) installed and available that includes a
wireless access point (WAP).
• Access to a power outlet.
Placement, Network Connection, and Power
Options
The 7” TabletopTouch Screen is equipped with the touch screen, four
programmable shortcut buttons, a light sensor, and a proximity sensor.
Place the touch screen on a table or level surface in a convenient location.
This device can use either an Ethernet or WiFi network connection. An
Ethernet installation can be powered by Power over Ethernet (PoE) or an AC
connection. A WiFi installation must use an AC power connection.
NOTE:
Do not attempt to use PoE and AC at the same time.
Option 1: Ethernet Connection with PoE
PoE injects electrical current into the Ethernet cable using a PoE injector in
order to provide the touch screen with both power and a network connection.
To set up your PoE and Ethernet connection, see Figure 1. The touch screen
works with the Control4 Power Over Ethernet Injector (model # AC-POE1-B).
FIGURE 1.
Ethernet - Requires connection to PoE injector.
Place the PoE Injector near your gateway/router/switch. Pull the Ethernet
cable from that location to the location of where you want to place your touch
screen.
Option 2: Ethernet Connection with AC
No PoE injector is needed for Ethernet with AC power; the Ethernet is
connected directly to the switch. This power connection requires both neutral
and hot connections. See Figure 2.
FIGURE 2.
Ethernet - Requires connection to Ethernet and AC power
Option 3: WiFi Connection with AC
When using WiFi, the touch screen gets its power from an AC power source
nearby. This power connection requires both neutral and hot connections.
See Figure 3.
Place the touch screen above a power source, such as at an outlet. Ensure
you have WiFi in the home.
FIGURE 3.
WiFi - Requires AC power and WAP.
Front and Rear Panel Description
Front View
1. Display: 7” viewing area, Touch-Screen with 800 x 480 resolution TFT
2.
Shortcut buttons (4): For custom programming to initiate an action or
sequence of actions
3.
Proximity sensor: Laser sensor that detects movement within two feet of
the touch screen and turns off screen saver
4.
Reset button: Button located under the bezel to reset touch screen.
5.
Light sensor: Detects light levels in room for programming purposes
6.
Front Dimensions (H x W x D): 6.95” x 8.37” x 4”
Back View
1. RCA audio line-level output: (Optional) Audio ports available for an ampli-
fier or amplified speakers for audio output using a standard RCA stereo
cable
2.
RG-45 port: Ethernet port available for either a standard Ethernet source
that provides network communication only OR a PoE source
(IEEE802.3af PoE) that provides power to the device and network com-
munication
3. AC power port: 9-12 VDC jack
4. AC power cord recess
5. Network Support: Ethernet or WiFi IEEE 802.11 b/g
Top of Table
Top of Table
Top of Table
1
2
3
6
5
4
1
2
3
4