® Controll-A-Door P Diamond and Whisper Quiet Sectional Door Opener Instruction Manual N1854 Manufacturer’s Part # 79075 (Manual) B&D Doors is a division of B&D Australia Pty Ltd ABN 25 010 473 971 www.bnd.com.
Controll-A-Door ® P Diamond Instruction Manual ® Controll-A-Door P Diamond Sectional Door Opener Safety Rules 03 Default Settings & Specifications 04 About Your Opener 05 How To Use Your Opener 24 Transmitter 24 Transmitter Battery 25 Operating Controls 06 Locking 25 Kit Contents 08 Manual Release 25 Installation 10 Power Failure 25 Knockdown C-Rail Assembly 10 Safety Infra-red Beam 26 Determine Door Type 12 Auto-Close 26 Mounting - Track Type Door 13
Controll-A-Door ® P Diamond Instruction Manual Safety Rules Please read these important safety rules These safety alert symbols indicate a personal safety or property damage instruction exists. Read these instructions carefully. This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules.
Controll-A-Door ® P Diamond Instruction Manual Default Settings & Specifications Factory default settings Default Step Minimum Maximum Maximum opener run time 30 seconds - - - Courtesy light time 4 minutes (approx.) - - - Obstruction force margin 2 1 0 14 Auto-Close time 30 seconds - - - Technical specifications Rated temperature +5° to 40°C Power supply 230V - 240Va.c. 50Hz Transformer rating 24Vd.c. Standby power 2.2 Watts Motor power 100 Watts Motor type 24Vd.c.
Controll-A-Door ® P Diamond Instruction Manual About Your B&D Opener Thank you for choosing a Controll-A-Door® P Diamond automatic garage door opener, designed and developed in Australia by B&D Doors.
Controll-A-Door ® P Diamond Instruction Manual Operating Controls 01. 10 Amp fuse to protect the electronic circuit board. 02. Terminal is used to connect Va.c. power to the control board. 03. SBY-3 Battery Charger connection to attach a Battery Back Up kit. 04. 24Vd.c. Motor Connection. 05. OPERATE button (Blue) is used during installation to test the open, stop and close cycles for the opener. The opener has to be initialised by the LIMIT SET button to make the OPERATE button operable. 06.
Controll-A-Door ® P Diamond Instruction Manual 7 05 04 06 03 01 02 07 16 15 15 08 09 14 10 13 11 12 © Copyright 2007 B&D Doors Diamond PD Power Drive : Instruction Manual Fig.
Controll-A-Door ® P Diamond Instruction Manual Kit Contents Powerhead Unit (Fig. 02) Fig. 02 1 x Controll-A-Door® P Diamond powerhead 1 x Transmitter pack (Pack includes two keyring transmitters and batteries) 1 x Wall mount transmitter with battery 2 x Door attachment arms 1 x Accessory and hardware pack 1 x Installation Manual PLUS Single Piece C-Rail with Pre-Assembled Chain (Fig. 03) Note: Chain in one piece rail has been tensioned by the factory. Adjust the tension of the chain to suit. Fig.
Controll-A-Door ® P Diamond Instruction Manual 9 Kit Contents Multi Piece Knockdown C-Rail with Pre-Assembled Chain (Fig. 05) IMPORTANT NOTE: If a modification to the length of the track is required, the adjustment must be made from the powerhead end only. Fig. 05 OR Multi Piece Knockdown C-Rail with Pre-Assembled Timing Belt (Fig. 06) IMPORTANT NOTE: If a modification to the length of the track is required, the adjustment must be made from the powerhead end only. Fig.
Controll-A-Door ® P Diamond Instruction Manual 10 Knockdown C-Rail Assembly Step 1 - Assemble the C-Rail (Knockdown C-Rail units only) Unpack and assemble the C-Rail using the steps outlined below in (Fig. 07). Fig.
Controll-A-Door ® P Diamond Instruction Manual 11 C-Rail Assembly Step 2 - Attach C-Rail to Powerhead Locate and insert the powerhead’s shaft into the C-Rail’s sprocket as shown in (Fig. 08). Shaft Fig. 08 Locate shaft into sprocket Step 3 - Secure C-Rail to Powerhead Fix the two track brackets as shown in (Fig. 09). Fix with the four screws supplied in accessory pack. Hex flange screw taptite ‘S’ M4 X 10 2) t (x cke a r b ck Tra Fig.
Controll-A-Door ® P Diamond Instruction Manual Determine the Door Type Step 4 - Determine the Door Type Proceed from Step 5 Determine which type of garage door you have as illustrated in (Fig. 10) to (Fig. 12). Track For a sectional (panel) door on tracks (Fig. 10) proceed with the installation from Step 5. Fig. 10 Door Sectional door with track Proceed from Step 5 For a one piece door on tracks (Fig. 11) proceed with the installation from Step 5. Track Fig.
Controll-A-Door ® P Diamond Instruction Manual 13 Mounting on a Track Type Door Step 5 - Determine Bracket Position a. b. c. Open the door and find the highest point of travel of the top door panel. Using a level, transfer this height to the wall above the door (Fig. 13) and mark a line 60mm above it. Determine the centre point on the wall above and on top of the door. Then draw two (2) lines extending 21.5mm from each side of the centre point.(Fig. 14) Level Level Track Track Fig.
Controll-A-Door ® P Diamond Instruction Manual Mounting on a Non-Track Type Door Centre of door Warning: Make sure concrete, brick wall or timber lintels are solid and sound so as to form a secure mounting platform. Fig. 17 Step 9 - Determine the Door’s Centre a. b. Find the centre of the door and mark this location both above the door and on top of the door. Draw two lines 21.5mm either side of this (Fig. 17). Step 10 - Prepositioning the Opener a. b. c. Raise the door to open position.
Controll-A-Door ® P Diamond Instruction Manual 15 Mounting Door Bracket and Arms Step 12.1 - Alternative Mounting Option Drill hole at centre of track (recommended bolt size M6 or M8) The opener can be fastened to the roof by driving a bolt through the C-Rail into a structural timber support. The bolt head’s height must not exceed 6mm (Fig. 21). Fig. 21 Ceiling Step 13 - Mounting Door Bracket The door bracket comes in two parts.
Controll-A-Door ® P Diamond Instruction Manual 16 Setting Travel Limits Important note: The OPERATE button will not function until the open and close limit positions are set. Note: The door and shuttle must be engaged into the chain index. The door should be open approximately half way. Fig. 25 Step 15.1 - Setting Limits Positions a. b. c. d. e. Remove the controls cover to access the controls panel as shown in (Fig. 25). Replace it when setup is completed.
Controll-A-Door ® P Diamond Instruction Manual 17 Testing Safety Obstruction Force CAUTION: Take care when testing the safety obstruction force. Failure to follow this warning can result in serious personal injury and/or property damage. 16.1 Test the Close Cycle a. b. c. d. Press the OPERATE button to open the door (Fig. 28). Place a piece of timber approximately 40mm high on the floor directly under the door (Fig.
Controll-A-Door ® P Diamond Instruction Manual Coding Transmitters Step 17.1 - Storing the Transmitter Code The opener can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to fourteen (14) codes can be stored in the receiver’s memory. Fig. 30 Press CODE SET button once a. b. Select one of the four buttons you wish to use to control the door c. d. e. Fig.
Controll-A-Door ® P Diamond Instruction Manual 19 Coding Transmitters Step 17.3 - Setting the Transmitter to Operate Vacation Mode The opener can be programmed into a “Vacation Mode” where the opener will not respond to any transmitter except one preprogrammed unit. a. b. c. d. e. Press CODE SET button three times. The CODE SET LED will illuminate and the courtesy light will flash slowly (once every two seconds) to indicate Vacation learning mode is active. (Fig.
Controll-A-Door ® P Diamond Instruction Manual Coding Transmitters Step 17.5 - Setting the Transmitter to Operate Pet (Pedestrian) Mode The opener can be programmed into a “Pet Mode” where the door opens partially to allow pets to enter/exit the garage: Fig. 34 Press CODE SET button five times a. b. Select one of the four buttons (not programmed yet ) you wish to use to control the door for pet position c.
Controll-A-Door ® P Diamond Instruction Manual 21 Accessories Terminal Block A variety of wired accessory items can be connected to the terminal block such as Safety Infra-red Beams, electric key switch, door status indicators and more (Fig. 37). The terminal block also features and auxiliary output for controlling other devices from your transmitter. These can include: an alarm system, external lighting, or an automatic gate. Terminal connections from top down are as follows: 1. 30V PWR (+ve) 2. P.
Controll-A-Door ® P Diamond Instruction Manual Accessories Safety Infra-red Beam (Part No 062734) For ADDITIONAL PROTECTION B&D Doors STRONGLY recommend the fitting of a Safety Infra-red Beam. In most countries Safety Infra-red Beams are mandatory on all garage doors fitted with automatic openers. For a small additional outlay, B&D recommends that Safety Infra-red Beams be installed with the automatic opener ensuring additional safety and peace of mind. Fig.
Controll-A-Door ® P Diamond Instruction Manual 23 Battery Back Up Installation Fig. 40 Battery Back Up (optional) The opener has provision for a Battery Back Up kit that allows continued operation of the door in the absence of mains power. Testing Battery Back Up 1. 2. Installation 1. 2. 3. 4. 5. 6. Disconnect power to the opener. Remove screws and swing the cover open (Fig. 40). Mount battery pack and secure with item 11 and 12.
Controll-A-Door ® P Diamond Instruction Manual How to use your opener For maximum efficiency of your opener, your garage door must be in good operating condition. An annual service of your garage door by an Approved Dealer is recommended. CAUTION - Activate the opener only when the door is in full view, free of obstructions and with the opener properly adjusted. No one should enter or leave the garage while the door is in motion. Do not allow children to play with or near the door. Fig.
Controll-A-Door ® P Diamond Instruction Manual 25 How To Use Your Opener Removing the Battery From the Transmitter (Battery Type: 3V Lithium Battery CR2032). Use a non-metallic object (e.g. pen) to remove the battery. (Fig. 42) Inbuilt Locking Facility DO NOT lock your door when your opener is engaged as it has inbuilt locking facility. With the opener engaged your door will be locked whether the power is on or off. Fig.
Controll-A-Door ® P Diamond Instruction Manual How To Use Your Opener Safety Infra-red Beam A Safety Infra-red Beam Kit (Part No 062734) may be fitted to this opener. • When this option is fitted, the operation of this device is such that if an object (i.e. car, child, etc.) blocks the Safety Infra-red Beam, then the garage door opener will not close the door automatically.
Controll-A-Door ® P Diamond Instruction Manual Maintenance Maintenance The SERVICE LED will indicate the requirement for a service and/or adjustment. To reset the SERVICE LED when the door is serviced, reprogram the Door Travel Limits and the Door Travel Force – on completion of this programming the SERVICE LED will go out. Whilst your opener does not require any periodic maintenance, the door that it is fitted to does.
Controll-A-Door ® P Diamond Instruction Manual Troubleshooting Guide Symptom Possible cause Remedy The opener does not work from the transmitter Garage door in poor condition e.g. springs may be broken Check the door’s operation - see monthly maintenance (Page 27) The opener does not have power Plug a device e.g.
Controll-A-Door ® P Diamond Instruction Manual Parameters Door status indicators Door opener state OPEN LED (green) Open On Close Opening CLOSE LED (red) Beeper On Flashing Closing Flashing Door travel stopped Flashing Door obstructed when opening Flashing Door obstructed when closing Flashing Flashing Opener overloaded Alternating flashes Door in open position with AutoClose mode selected One second flashes Mains power interrupted Rapid flashes Beeps while door is moving Alternatin
062821 062841 062842 062843 20 TIMING IDLER 21 TIMING BELT T10-6280 22 TIMING INDEX CLAMP 23 TIMING INDEX SLEEVE 062794 29 GEARED MOTOR ASSY 14-V2 33 TIMING HARNESS 350 ASSY 062789 65 BELT GUIDE VP2 64 TRANSMITTER TB-4 TWIN PACK 31 TIMING ASSY 32 DUST COVER TOP 63 PLASTIC WALL PLUG PACK 62 LITHIUM BATTERY 3V CR2032 30 HELICAL GEAR 85075-12 CP ASSY 062790 60 STRAIGHT ARM 062788 28 WIRE EARTH ASSY 220L 61 WALL TRANSMITTER WTB-4 RG SV1 59 BENT ARM 062792 27 POWER CORD 1.
Controll-A-Door ® P Diamond Instruction Manual © Copyright 2007 B&D Doors Diamond PD Power Drive : Instruction Manual 31
Controll-A-Door ® P Diamond Instruction Manual Warranty 1. Definitions ‘B&D’ means (a) in Australia - B&D Doors of 17 Oasis Court, Clontarf, Queensland, 4019, a division of B&D Australia Pty Ltd (ABN 25 010 473 971), or (b) in New Zealand - B&D Doors NZ Ltd of 70 Allens Road East Tamaki Auckland, which is a subsidiary of B&D Australia Pty Ltd. ‘Purchaser’ means the purchaser of the Opener.
Controll-A-Door ® P Diamond Instruction Manual Warranty 9. Subject to paragraph 12 hereof; (i) the obligations of B&D under this warranty are limited to those contained herein and such warranties are expressly in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose and notwithstanding any course of dealing between the parties or custom and usage in the trade to the contrary.
Controll-A-Door ® P Diamond Instruction Manual Optional Accessories There is a range of additional accessories for your added convenience and security. • Safety Infra-red Beams - Part No 062734. Gives additional protection if the door is closing onto your property or person. Simply breaking the beam “stops” the door! Must be fitted if the Auto-Close feature is operational. • Keyring Transmitter - Part No 062731. Ideal for personal use when entry into the house may be via the garage.
Controll-A-Door ® P Diamond Instruction Manual © Copyright 2007 B&D Doors Diamond PD Power Drive : Instruction Manual 35
QLD Office: 17 Oasis Court, Clontarf 4019. Ph: (07) 3883 0200 NSW Office: 34-36 Marigold St, Revesby 2212. Ph: (02) 9722 5555 VIC/TAS Office: 147-153 Canterbury Road, Kilsyth 3137. Ph: (03) 9237 7766 SA Office: 23 Frederick Road, Royal Park 5014. Ph: (08) 8440 4747 WA Office: 96 Mulgul Drive, Malaga 6062. www.bnd.com.au Ph: (08) 9247 8777 NZ Office: 70 Allens Road, East Tamaki, Auckland. www.bnd.co.
