® Controll-A-Door P Diamond Sectional Door Opener SDO-2v2 Instruction Manual Technical Document Installation Manual 1.01 v 04 June 2012 English N1854 Part # 79073 (Manual) B&D Doors is a division of B&D Australia Pty Ltd ABN 25 010 473 971 www.bnd.com.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Controll-A-Door® P Diamond Sectional Door Opener SDO-2v2 03 Battery Back Up Installation 26 Risk Assessment 04 How To Use Your Opener 27 Default Settings & Specifications 05 Transmitter 27 06 Transmitter Battery 28 Operating Controls 07 Locking 28 Kit Contents 09 Manual Release 28 10 Power Failure 28 C-Rail Assembly 10 Safety Beam 29 Determine Door Type 11 Auto-Close 29 Mounting - Track Type Door 12 Courtesy Light
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Safety Rules Please read these important safety rules These safety alert symbols indicate a personal safety or property damage instruction exists. READ THESE INSTRUCTIONS CAREFULLY. This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Risk Assessment Please refer to the risk assessment table below and ensure all the necessary controls are in place.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Default Settings & Specifications Factory default settings Default Step Minimum Maximum Maximum opener run time 60 seconds - - - Courtesy light time 4 minutes (approx.) - - - Obstruction force margin 2 1 0 14 Auto-Close time 30 seconds - - - Technical specifications Power supply 230V - 240Va.c. 50Hz Transformer rating 24Vd.c. Standby power 2.2 Watts Motor power 100 Watts Motor type 24Vd.c.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual About Your B&D Opener Thank you for choosing a Controll-A-Door® P Diamond automatic garage door opener, designed and developed in Australia by B&D Doors.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Operating Controls 01. Terminal Block. V+ is used to power devices such as Wireless Safety Beam, external receiver etc. EB1 input is used to connect to Safety Beam. 0V (Input) is a 0 volt connection for Safety Beam, external receiver, osc, aux etc. EB2 input is used to connect to second Safety Beam.. 0V (Input) is a 0 volt connection for Safety Beam, external receiver, osc, aux etc.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 8 14 13 Fig.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 9 Kit Contents Powerhead Unit (Fig. 02) 1 x Controll-A-Door® P Diamond powerhead 1 x Transmitter pack (Pack includes two keyring transmitters and batteries) 1 x Wall mount transmitter with battery 2 x Door attachment arms 1 x Accessory and hardware pack 1 x Installation Manual Fig. 02 PLUS Single Piece C-Rail with Pre-Assembled Chain (Fig. 03) NOTE: Chain in one piece rail has been tensioned by the factory. Do not adjust the tension of the chain.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 10 C-Rail Assembly Step 1 - Attach C-Rail to Powerhead Shaft Locate and insert the powerhead’s shaft into the C-Rail’s sprocket as shown in (Fig. 05). Fig. 05 Locate shaft into sprocket ck Tra Fig.06 2) t (x cke bra w cre 10 es ang M4 X fl x ’ He tite ‘S tap Step 2 - Secure C-Rail to Powerhead Fix the two track brackets as shown in (Fig. 06). Fix with the four screws supplied in accessory pack.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 11 Determine the Door Type Step 3 - Determine the Door Type Proceed from Step 5 Determine which type of garage door you have as illustrated in (Fig. 07) to (Fig. 09). For a sectional (panel) door on tracks (Fig. 07) proceed with the installation from Step 4. Track Fig. 07 Door Sectional door with track For a one piece door on tracks (Fig. 08) proceed with the installation from Step 4. Proceed from Step 5 Track Fig.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 12 Mounting on a Track Type Door Step 4 - Determine Bracket Position a. Level Level Track Track Fig. 10 b. c. Door Door Open the door and find the highest point of travel of the top door panel. Using a level, transfer this height to the wall above the door (Fig. 10) and mark a line 60mm above it. Determine the centre point on the wall above and on top of the door. Then draw two (2) lines extending 21.5mm from each side of the centre point. (Fig.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 13 Mounting on a Non-Track Type Door WARNING: Make sure concrete, brick wall or timber lintels are solid and sound so as to form a secure mounting platform. Centre of door Fig. 14 Step 8 - Determine the Door’s Centre a. b. Find the centre of the door and mark this location both above the door and on top of the door. Draw two lines 21.5mm either side of this (Fig. 14). Step 9 - Prepositioning the Opener a. b. c. Raise the door to open position.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 14 Mounting Door Bracket and Arms Drill hole at centre of track (recommended bolt size M6 or M8) Fig. 18 Ceiling The height of bolt head must not exceed 6 mm Aluminium rail Step 11.1 - Alternative Mounting Option The opener can be fastened to the roof by driving a bolt through the C-Rail into a structural timber support. The bolt head’s height must not exceed 6mm (Fig. 18). Step 12 - Mounting Door Bracket The door bracket comes in two parts.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 15 Setting Speed and Limits Step 14 - Setting Speed Mode The default speed of the opener has been set to suit the majority of applications. However, there are 3 speed modes available if required:1. 2. 3. Slow - to suit one piece door without tracks Medium ( default ) - suits majority of applications Fast - to suit some sectional applications Fig. 22 The speed settings can only be changed before setting the travel limits.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Setting Travel Limits IMPORTANT NOTE: The OPERATE button will not function until the open and close limit positions are set. NOTE: The door and shuttle must be engaged into the chain index. The door should be open approximately half way. Fig. 23 Step 15.1 - Setting Limits Positions a. b. c. d. e. Remove the controls cover to access the controls panel as shown in (Fig. 23). Replace it when setup is completed.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 17 Testing Safety Obstruction Force CAUTION: Take care when testing the safety obstruction force. Failure to follow this warning can result in serious personal injury and/or property damage. 16.1 Test the Close Cycle a. b. c. d. Press the OPERATE button to open the door (Fig. 26). Place a piece of timber approximately 40mm high on the floor directly under the door (Fig 27). Press the OPERATE button to close door.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Coding Transmitters Step 17.1 - Storing the Transmitter Code The opener can only operate from transmitters that have been programmed into its receiver. The receiver needs to learn the codes of any transmitter that will be used with the operator. Up to fourteen (14) codes can be stored in the receiver’s memory. Fig. 28 Press CODE SET button once a. b. Select one of the four buttons you wish to use to control the door c. d. e. Fig.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 19 Coding Transmitters Step 17.3 - Setting the Transmitter to Operate Vacation Mode The opener can be programmed into a “Vacation Mode” where the opener will not respond to any transmitter except one preprogrammed unit. a. b. c. d. e. Press CODE SET button three times. The CODE SET LED will illuminate and the courtesy light will flash slowly (once every two seconds) to indicate Vacation learning mode is active. (Fig.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Coding Transmitters Step 17.5 - Setting the Transmitter to Operate Pet (Pedestrian) Mode The opener can be programmed into a “Pet Mode” where the door opens partially to allow pets to enter/exit the garage: Fig. 32 Press CODE SET button five times a. b. Select one of the four buttons (not programmed yet ) you wish to use to control the door for pet position c.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 21 Wireless Safety Beams Installation WARNING: Safety beams must be installed if the closing force at the bottom edge of the door exceeds 400N (40kg force). This is in compliance with AS/NZS 60335-2-95 Step 20.1 -Wireless Photo Electric (PE) Beams (optional) A photo electric (PE) Beams extends across the door opening.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Wireless Safety Beams Installation Step 20.3 -Connecting The Base Station To The Opener a. b. c. Fig. 41 + RESET Fig. 42 + Receiver LED Connect WHITE wire from base station to 0V on the terminal block of the opener Connect RED wire from base station to V+ on the terminal block of the opener. Connect YELLOW wire from the base station to EB1,EB2 or EB3 on the terminal block of the opener. See Fig. 40.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 23 Wireless Safety Beams Installation Step 20.5 -Fixing The Base Station To Wall/ Opener The base station can be attached directly to a sectional opener using the M8 bolt and nut supplied. The wire can be fed through the top gromet of the opener (Fig. 43) Fig. 43 Note: The bracket may also be rotated so the base station hangs above the power head. Step 20.6 Transmitter a. b. c. d. e. f.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Wired Safety Beams Installation WARNING: Safety beams must be installed if the closing force at the bottom edge of the door exceeds 400N (40kg force). This is in compliance with AS/NZS 60335-2-95 6 4 3 Step 19 - Safety Beams (optional) Fig. 35 Safety Beams extend across the garage door opening.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 25 Accessories Terminal Block A variety of wired accessory items can be connected to the terminal block such as Safety Beams, electric key switch, and more (Fig. 47). Terminal connections from top down are as follows: 1. V+ 2. EB1 (Safety Beam input) 3. 0V (0V for Safety Beam) 4. EB2 (Safety Beam input) 5. OSC (Open/Stop/Close trigger) 6. AUX OUT (Auxiliary output trigger) Remote Aerial (Part No 062177) Some sites cause poor radio reception.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 26 Battery Back Up Installation Fig. 48 Battery Back Up (optional) The opener has provision for a Battery Back Up kit that allows continued operation of the door in the absence of mains power. Installation 1. 2. 3. 4. 5. 6. Disconnect power to the opener. Remove screws and swing open the cover (Fig 48). Mount the PCB support with two screws item # 12. Secure the SBC0-2 Charger Board onto the PCB support with three (3) screws item #14.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual 27 How to use your opener For maximum efficiency of your opener, your garage door must be in good operating condition. An annual service of your garage door by an Approved Dealer is recommended. CAUTION - Activate the opener only when the door is in full view, free of obstructions and with the opener properly adjusted. No one should enter or leave the garage while the door is in motion. Do not allow children to play with or near the door. Fig.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual How To Use Your Opener Removing the Battery From the Transmitter (Battery Type: 3V Lithium Battery CR2032). Use a non-metallic object (e.g. pen) to remove the battery. (Fig. 50) Inbuilt Locking Facility Fig. 50 DO NOT lock your door when your opener is engaged as it has inbuilt locking facility. With the opener engaged your door will be locked whether the power is on or off.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual How To Use Your Opener Safety Beam A Safety Beam Kit (Part No 062734) may be fitted to this opener. • When this option is fitted, the operation of this device is such that if an object (i.e. car, child, etc.) blocks the Safety Beam, then the garage door opener will not close the door automatically. • If the Safety Beam is fitted but not operating correctly, then the door once opened automatically, will not close automatically.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Maintenance Maintenance Whilst your opener does not require any periodic maintenance, the door that it is fitted to, does. Your garage door is a large, heavy, moving object and should be tested regularly to ensure it is in good condition. A poorly maintained door could cause fatal or serious injuries or serious damage to property. Yearly B&D suggests that you contact your nearest Approved Dealer to perform an annual door service.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Troubleshooting Guide Symptom Possible cause Remedy The opener does not work from the transmitter Garage door in poor condition e.g. springs may be broken Check the door’s operation - see monthly maintenance (Page 30) The opener does not have power Plug a device e.g.
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Parameters Door status indicators Door opener state OPEN LED (green) Open On Close Opening CLOSE LED (red) Beeper On Flashing Closing Flashing Door travel stopped Flashing Door obstructed when opening Flashing Door obstructed when closing Flashing Flashing Opener overloaded Alternating flashes Door in open position with AutoClose mode selected One second flashes Mains power interrupted Rapid flashes Beeps while door is moving
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Spare Parts List © Copyright 2012 B&D Doors Diamond PD Power Drive : Instruction Manual 33
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Warranty Product: CAD P Purchased from:______________________________Purchaser:___________________________________ (described as “you” below) Address:_____________________________________Installed by:__________________________________ Installed on (date):____________________________Invoice No:__________________________________ 1 Making a claim - To make a warranty claim you must: (a) produce a copy of the receipt of purchase, together with this war
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Warranty (b) instructions - failure to observe any instructions or directions (including “warning” notifications in the Instruction Manual), provided with the Product or given to you; (c) other devices - the Product being fitted to any door or other closing device which is not of the type or condition defined in the Instruction Manual as suitable for installation of the Product; (d) installation or adjustment - faulty installation or adjustment of the
Controll-A-Door ® P Diamond SDO-2v2 Instruction Manual Optional Accessories There is a range of additional accessories for your added convenience and security. • Safety Beams - Part No 062734. Gives additional protection if the door is closing onto your property or person. Simply breaking the beam “stops” the door! Must be fitted if the Auto-Close feature is operational. • Keyring Transmitter - Part No 062731. Ideal for personal use when entry into the house may be via the garage.
QLD Office: 17 Oasis Court, Clontarf 4019. Ph: (07) 3883 0200 NSW Office: 34-36 Marigold St, Revesby 2212. Ph: (02) 9722 5555 VIC/TAS Office: 147-153 Canterbury Road, Kilsyth 3137. Ph: (03) 9237 7766 SA Office: 23 Frederick Road, Royal Park 5014. Ph: (08) 8440 4747 WA Office: 96 Mulgul Drive, Malaga 6062. www.bnd.com.au Ph: (08) 9247 8777 NZ Office: 70 Allens Road, East Tamaki, Auckland. www.bnd.co.
