Manual

4
P/N 190–112486 REV B
After installing your receiver and transmitter, check
the operation of your radio controls by moving
approximately 45 feet back from the garage door, then
press the transmitter button. Operation at this distance
should be reliable. However, environmental
conditions and the location of the transmitter and
receiver will affect distance.
• If the transmitter doesn’t activate the operator check
the coding on both the transmitter and receiver. The
code setting must match exactly . This may necessi-
tate a reprogramming of the transmitter and receiver.
• If the distance is inadequate check the battery and
replace if necessary.
• To maximize the operating distance move the
transmitter to different locations in the car until a
satisfactory distance is achieved. Vanity mirrors on
sun visors will affect performance.
• If the receiver is in the proximity of a metal beam or
other obstruction it may be necessary to relocate the
receiver to increase the operating range.
• If multiple receivers are mounted closer than 15 feet,
blocking and interference may occur. Move the
receivers further apart.
• If system does not work at any distance, check that the
receiver terminals are connected to the proper operator
terminals.
• If the HomeLink® transmitter does not activate the
operator or distance is inadequate,verify proper
operation using the hand-held transmitter. Contact
your HomeLink® system provider for help with
configuring the HomeLink® transmitter and to
resolve distance problems when using the
HomeLink® system.
Operational Check
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
WARNING
Unexpected door operations can cause personal injury or property damage.
LINEAR LIMITED WARRANTY
This product is warranted to the consumer against defects in material and
workmanship for one year from the date of purchase. This warranty applies to first
retail buyers of new devices. Warrantor will repair, or at its option, replace, any
device it finds that requires service under this warranty, and will return the repaired
or replaced device to the consumer at the warrantor’s cost. For warrant service
and shipping instructions contact warrantor at the address shown below. Devices
must be sent to warrantor for service at owner’s expense. The remedies provided
by this warranty are exclusive. Implied warranties under state law are to the one
year period of this written warranty. Some states do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. In
order to be protected by this warranty, save your proof of purchase and send copy
with equipment should repair be required. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
For warranty service and shipping instructions contact Linear at the phone number
shown below. In order to be protected by this warranty, save your proof of
purchase and send a copy with equipment should repair be required. All products
returned for warranty service require a Return Product Authorization Number
(RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and
other important details.
MVP Radio Controls are compatible with HomeLink®.
Homelink® is a registered trade mark of Johnson
Controls, Inc.
Garage Door and Gate Operator Radio Controls
MVP Receiver and Transmitters
Product Features
These controls are designed to remotely
operate garage door and gate openers. The
MVP receiver is compatible with Classic,
MVP and Original Allstar, Allister and Pulsar
type dip-switch transmitters. The MVP
receiver is available in one and three-door
versions and may be used as shown below.The
radio frequency of the remote controls is fixed
and tuned at the factory. RF adjustments are
not required and should not be attempted by
the end user. There are no user serviceable
parts in the radio controls.
Disconnect power to operator
before any installation or repair.
Follow all instructions provided by
the manufacturer of your operator.
WARNING
Installation Steps
First, determine the type of operator (with or
without receiver power). Refer to the operator
manual or contact the operator manufacturer
as needed. Next, attach the receiver to the
operator according to the appropriate
installation instructions. Next, set the
transmitter codes according to the instructions
provided with the transmitter. To finish,
program the receiver with the transmitter
codes.
Installation on Operator Without
Power for Receivers
Some operators do not provide power for an
external receiver. An optional transformer kit
is required. Disconnect power to the operator
before installing receiver. Connect the red and
white wires of the receiver to the transformer.
Connect black wires on the receiver to the
terminals on the operator.
Receiver Wiring
The receiver provides one set of normally
open isolated contacts (2 black wires). The red
and white wires provide 24 VAC or DC power
to the receiver.
To wire, connect the white wire to ground or
common and red wire to 24 VAC or DC. Next
connect the black wires to the pushbutton
circuit you wish to control.
If the receiver is connected to a 3-terminal
system, connect the red and white wires to
power, connect either black wires to ground or
common and the other to the pushbutton.
USA & Canada
[phone] & [phone]
[phone]
Toll Free FAX [phone]
www.linearcorp.com